| Age | Commit message (Collapse) | Author |
|---|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
Touchpad: 386.7kHz
Touchscreen: 387.4kHz
Audio: 385.7kHz
P-sensor: 378.1kHz
BaUG=b:197247706
BRANCH=dedede
TEST=Build and check I2C clock is under 400kHz
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ic5d5660181f36f161ae04cbf5003f6d7ad4bc16f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add MT53E512M32D1NP-046 WT:B supported memory part in the
mem_parts_used.txt and generate the SPD ID for the part. Manufacturer
is Micron, and the memory part is 1anm Tech, difference to 1xnm Tech
on MT53E512M32D2NP-046.
BUG=b:194223174
BRANCH=dedede
TEST=Build the gooey board.
Change-Id: I7b83126a2bf98bb9d0ca05d397c288e0d99ed781
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57310
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drawper change LTE reset pin from GPP_H0 to GPP_H17 from DVT phase.
BUG=b:198117092
TEST=emerge-dedede coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ib65580babf7d21535df2bd8d33bb19261bebfe15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
|
|
TEST=none
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I6346b087543217c78f87751051a4f38b23c566d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Guybrush based boards must usa a dedicated eSPI alert#.
Must be open drain to prevent power leaks.
Keep guybrush reference board in-band since alert# may not be connected.
BUG=b:198409370
TEST=Build guybrush and nipperkin, boot guybrush
BRANCH=None
Change-Id: I4b23bfc6a1167aebfde5acd524fda043b63163dc
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The overrides set the options to the same value as drivers/intel/fsp2_0/
Kconfig does, so drop the overrides.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53922786382a2e7d29b3df560a1998f41e1d2ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Normally, selecting FSP_USE_REPO will select FSP_FULL_FD which then will
configure the proper paths for FSP_M_FILE and FSP_S_FILE. The override
in these two boards caused FSP_M_FILE and FSP_S_FILE being empty despite
ADD_FSP_BINARIES being selected by FSP_USE_REPO which is an invalid case
that needs to be avoided, so remove the board-level override of those
two options.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I20c8cebea8327d59f0f33d05b824a74bf2121f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The ADD_FSP_BINARIES override in the mainboard's Kconfig caused this
option to not be selected when FSP_USE_REPO is selected. Remove the
override to fix this problem. These two boards are the only ones in tree
that had an override for this option, so now the ADD_FSP_BINARIES option
is only defined in drivers/intel/fsp2_0/Kconfig.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23439f3134eef9460625addbff7efd64c5f65ae5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
If a USB_MUX_EVENT happens while the AP is in S3 during powerdown
transtion (S0->S3->S5), this will cause the device to boot again after
it has finished sequencing down to S5. Since S3 is not POR for ChromeOS
devices anymore, change this event to wake from S3 and S0ix to just
S0ix.
BUG=b:197039097
TEST=abuild
Change-Id: I91e5e0ab8301377817875b6fa9e3c0e1f96c1465
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
There are two different types of 682 SKU available with TDP
of 28W and 45W. This patch fix override values for power
limits for these 682 SKU. This patch also sets power limit
values dynamically based on machine ID and CPU TDP of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I796e56321ae9c8312530a4b8986cd73a2245f5fa
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57290
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce DDR One-Time-Training Support
Device reboots without training from second iteration
and also DDR training data is 32kb size, hence update
required in memlayout and to sync with upstream changes
the Fmap size even got bumped up.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I81038c5c7802c154f4310509c6c64710580b8ce4
Signed-off-by: Sudheer Kumar Amrabadi <samrabad@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Configure 384MHz for eMMC clock and 50MHz for SD card clock.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I8acbce58614add0228adc39289762da10937cbe2
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add TPM IRQ config to gpio_m.c, so the TPM IRQ is not allocated
to I2C4.
BUG=NA
BRANCH=None
TEST= boot to os and check cat /proc/interrupts, cr50 SPI interrupt is assigned
and does not conflict with I2C.
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 CPU8 CPU9 CPU10 CPU11
0: 36 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 2-edge timer
1: 0 0 0 0 0 0 0 0 9 0 0 0 IO-APIC 1-edge i8042
8: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 14-fasteoi INTC1055:00
16: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 16-fasteoi intel-ipu6
22: 0 13 0 0 0 0 0 0 0 0 0 0 IO-APIC 22-fasteoi idma64.4, i801_smbus, ttyS0
37: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 37-fasteoi idma64.0, i2c_designware.0
38: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 38-fasteoi idma64.1, i2c_designware.1
41: 0 0 0 0 2274 0 0 0 0 0 0 0 IO-APIC 41-edge cr50_spi
42: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 42-fasteoi idma64.2, i2c_designware.2
43: 4 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 43-fasteoi idma64.3, i2c_designware.3
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: Id0f3885dec5a6f635254c233709090321491c739
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57102
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add GPIO IOMUX defines for the pins that are used in the mainboard code
which enables using the PAD_GPI and PAD_GPO macros.
TEST=Timeless build for APU2/3/4/5 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie32df9ed2cb6a5670a29cff91e085a3585c8bcf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
The mapping of the package GPIO numbers to the GPIO numbers on the GPIO
controller isn't a 1:1 one, so add a comment about that to avoid
confusion. Also change the comment style to match the style guide.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie30bf5483ea2e2516d7e3fdd21ea9338362e526e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Also remove the unused amdblocks/acpimmio.h include in gpio_ftns.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: If121941c8a6ba88913653192740997aeef426548
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56784
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override DdiPortAConfig as MIPI DSI
BUG=b:192521391
BRANCH=None
TEST=Built test coreboot image and boot on bugzzy board
Change-Id: If308f9d69fea56176527e7b67f36b29c43adb525
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
CONFIG_DRIVERS_INTEL_MIPI_CAMERA and CONFIG_SOC_INTEL_COMMON_BLOCK_IPU
are getting selected for all ADLRVPs irrespective of ADL-P and ADL-M
(internal and external EC SKUs) hence, select those Kconfigs from
mainboard Kconfig rather Kconfig.name.
Also, select DRIVERS_INTEL_SOUNDWIRE as per alphabetical order.
TEST=No changes are seen while the .config file is getting auto
generated.
Change-Id: I62d5ec19c3364da79ebe7287b1b3d6eb2a0efca0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the `UserBd` FSP-M UPD to `BOARD_TYPE_DESKTOP` by default on PCH-H.
Remove now-redundant mainboard code to set the `UserBd` UPD.
Change-Id: I349abe5d89f562c158ce9baadbca2b2f56695846
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57261
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SoC code already sets this UPD to `CONFIG_IED_REGION_SIZE`, which
defaults to 0x400000 for soc/intel/cannonlake.
Change-Id: I6587e17a4a3425c561cffe6e3df0d932a2458168
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I291dc71bb6e3888b71ebce315f9ad09ccbc4a9a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_MAX` Kconfig symbol once.
Change-Id: I2e86baaa8bd50c7b82c399fde5dcea05da6b4307
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
variant_has_pcie_wwan() was always coming back as disabled because
find_dev_nested_path() couldn't find the device until the domain was
added to the array.
BUG=b:193036827
TEST=Boot guybrush with PCIe & USB WWAN devices.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id94fa0b0ff5c29fa447e869220d27ccfe61438c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The RW_MRC_CACHE only needs to be 64K for Brya.
BUG=none
TEST="emerge-brya coreboot chromeos-bootimage", flash and boot
brya0 to kernel.
Change-Id: I74365b795e184b92f483ae2bf862791e235c5362
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56989
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO PM was disabled for brya to evaluate if longer interrupt pulses
are required for ADL. Since ADL requires 4us long pulses (EDS:626817),
GPIO PM can be enabled. All devices currently tested on brya support 4us
long pulses. This change drops the GPIO PM override and re-enables
dynamic GPIO PM.
TEST=Boot brya to OS, ensure no TPM errors.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0c7b66b5514d8b80775ab7578ce7b12181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56926
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It doesn't make sense to store the orientation field directly in the
panel information structure, which is supposed to be reuseable between
different boards. The thing that determines orientation is how that
panel is built into the board in question, which only the board itself
can know. The same portrait panel could be rotated left to be used as
landscape in one board and rotated right to be used as landscape in
another. This patch moves the orientation field out of the panel
structure back into the mainboards to reflect this.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If2b716aa4dae036515730c12961fdd8a9ac34753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57324
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable PCIE port 7 using clk 6 for RTL8125 Ethernet
BUG=b:193750191
BRANCH=None
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic60a66dbd6ad87cf9c0de85ca7df4d854c371bf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Windows will write to the century byte (0x32), causing the option table
checksum to be invalid and reset all options to their default values.
Move options and checksum to start after the century byte.
Change-Id: Ia395acacda1e251251c880587bbf61d7ee81ba3d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNCPMMLXR-NEE
K4UBE3D4AA-MGCR
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I71ceaf0a2738584d316a5b7cc51539821b430128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
It turns out that putting a device ref in an overridetree at a different
point in the tree will generate a duplicate device definition, such that
the change introducing this support was ignoring the device presence
specified by overridetree.cb and only using the baseboard configuration.
I believe testing of that change was not redone after the baseboard was
changed to disable the MST, so that conflicting behavior was not
noticed.
The incorrect behavior generated a disabled device for the MST at the
location specified by the baseboard, and one with the probe as a child
of the soc. At runtime this did a fw_config probe of the "I2C 00:4a"
device, and later probed a different "I2C 00:4a" which was already
disabled. As the disabled one came later, it seems to have completely
disabled the MST, discarding the results of the variant-specific probe.
BUG=b:185862297
TEST=10EC2141 device is now present on a Dali berknip
BRANCH=zork
Change-Id: I2a8feb544f3fc198fe6313b226ad8995aad31c3e
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57298
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable this feature, and it can use the probe statement in devicetree
to cache of fw_config field as oem string.
BUG=b:191931762
TEST=With CBI FW_CONFIG field set to 0x8,
set probe AUDIO MAX98390_ALC5682I_I2S_4SPK in devicetree
dmidecode -t 11
OEM Strings
AUDIO-MAX98390_ALC5682I_I2S_4SPK
Change-Id: I93cd9ef2d1ad963e66c422cff17b083abf731046
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change moves the hda device enabling from baseboard device tree
to override tree for the variants that did not provide any hda
specific nodes. This ensures that the probe statements are correctly
selected by the variant depending upon the configurations it
supports.
Change-Id: Ib7b36468f17fbd65eb3d7d9355fcf78148aeb44a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57123
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
volteer baseboard was currently enabling TBT(USB4) devices in
baseboard devicetree and also selecting the Kconfigs required for
resource allocation above 4G for the USB4 controllers. However, not
all volteer devices have USB4 support. This change fixes USB4 enabling
for volteer family by making the following udpates:
1. TBT devices are moved from baseboard devicetree to individual
override trees for the variants that actually support USB4.
2. When moving TBT devices to override tree, tbt_pcie_rp0 is marked as
on instead of hidden for all variants other than volteer
reference. This is because volteer reference is the only device that
has an asymmetric support for USB4 (i.e. does not support USB4 on C0
port).
3. Kconfig selection for PCIEXP_HOTPLUG is moved to Kconfig.name for
these variants.
Change-Id: If380dcb1ea1633b3a1d6932e769cb6ed0a2761c7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57112
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DEV0 - 0x3a i2c-MX98390:00: Right Speaker
DEV1 - 0x3b i2c-MX98390:01: Left Speaker
DEV2 - 0x38 i2c-MX98390:02: Right Tweeter
DEV2 - 0x39 i2c-MX98390:03: Left Tweeter
This is to consist with other 2 speakers configs, and m/c driver design.
uid0/1 = regular speakers.
uid2/3 = tweeter
BUG=191931762
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I0a3183b1e1ecbb109258d6e076551158e0b40ce1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Using tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:194163604
TEST=build and test on cret and cret360
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ie94c2a07ad43fe1cb426e543dd97ed0434c42f2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add SPD support to gimble for LPDDR4 memory part K4UBE3D4AA-MGCR.
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ida21fd50129412af59a341dea45232fd0f9931ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57253
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP-S disables UART #0 as per the `SerialIoDevMode` settings.
Change-Id: Ic1f9f7ce6fd4f453200d563bd8556946eef1b287
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Mimoja <coreboot@mimoja.de>
|
|
Commit 98ec53bdf15ff79369307862e71142d4606f9e5a (mb/google/caroline:
Re-enable I2C2 / fix digitizer) enabled I2C #2 in the `SerialIoDevMode`
array, but left the device disabled in the devicetree. Enable it.
Change-Id: I67eec1c753bfd2a78ed0c1e0a78057cd4a3d4153
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
FSP-S configures the GPIOs for enabled SerialIO devices. However, Poppy
boards only enable UART 0 because it's function 0 of PCI device 30, and
the PCI specification requires that function 0 of multifunction devices
be implemented if other functions are implemented as well.
Nautilus got remedied in commit 8a1f095e50e068e42d378f47c79467e7b6295b7b
(mb/google/poppy/variants/nautilus: Update camera power enable GPIOs) by
using `PchSerialIoSkipInit` for UART 0, which tells FSP to not touch the
SerialIO device. This way, it remains enabled and the GPIO settings will
not be overwritten by FSP.
However, not all variants do this, but use some UART 0 pads as GPIOs. To
prevent any issues, configure UART 0 as `PchSerialIoSkipInit` on all the
variants.
Change-Id: I7e3a61769ef9e3b348ce84c663f67d3c4c5d9485
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55236
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the SPI configuration has been moved into Kconfig, it is no
longer needed in devicetree.
BUG=b:194919326
TEST=Build & boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ifdcd3f33173194c4a25794137756b143751edd70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This fix will enable PCIe x1 slot for ADL-M LP4 and LP5 RVPs.
The BDF for this PCIe slot is pci is: 0000:00:1d.0
TEST = show device command:
$ lspci -s 00:19.0
expect this:
00:19.0 Serial bus controller [0c80]: Intel Corporation Device 51c5
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ia988fa0b5d8fefe68503b39843aab06c4229b36f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57053
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on latest schematic to update the gpio table.
BUG=b:197308586
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0d91199ffd2128a136ea0a33dfe7affa77ae61d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on latest shcematic to update the device tree.
BUG=b:197308586
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I59601571c5e4c2d19738cb333605fb22e1ea0d2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable flag SOC_INTEL_COMMON_BLOCK_TCSS.
BUG=b:187385592
TEST=type-C pendrive/Gen-2 SSD detected as Super speed.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: Ie3cb8b8836b17fa00ab0089d03fca9f22c4d702e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54090
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to schematics, TSR2 thermal sensor is not present in driblee.
BUG=b:191732473, b:197180925, b:195868075
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I343a6161f71f66b77d23f1fa2f581aaee5eddf1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57091
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the combination audio CS42L42 and amp. MAX98360.
BUG=b:195619349, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I264c680ed5638b71c912253a38c27152a9015d4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This change follows other Intel SoCs common way to support SKUs with
bsp lapic_id != 0 by removing hardcoded lapic 0 from devicetree.cb and
allowing its detection at boottime. It completes support for HCV/DNV
after base SoC patch: commit ba936ce5db819d5ecb34e83a998b2390ecbdc4b9
soc/intel/denverton_ns: Ensure CPU device has a valid link
Link: https://mail.coreboot.org/hyperkitty/list/coreboot@coreboot.org/thread/YLMK2FBWWL6RKDNKBVZB3NJDYMEYHED7/
"A different lapic number in devicetree.cb needed for CPU with the same SKU and steping (Intel Atom C3538)."
Change-Id: I88f60f64d2beb2768ec9833de582d7901f456b11
Signed-off-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: King Sumo <kingsumos@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This documentation doesn't add any more value. Thus, remove it.
Change-Id: I0402bc736c6cc77d88a836bddce8eadae8ec5d7c
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Modify USB 2.0 port5 parameter to improve SI diagram measurement.
BUG=b:187992881
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I1eff05a7ad6563898744c24f9657e28625319873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:194356991
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Change-Id: I71b824c42c13cc2a8bebe0072de4a65ce238f074
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory part in the mem_parts_used.txt and generate the
SPD ID for the part. The memory part being added is:
MT53E512M32D1NP-046 WT:B
BUG=b:194223174
BRANCH=dedede
TEST=Build the boten board.
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I36fcbf7333fd9e85b28baa64676f8435aca63889
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E1G32D2NP-046 WT:A
H9HCNNNBKMMLXR-NEE
K4U6E3S4AA-MGCR
MT53E512M32D2NP-046 WT:E
H9HCNNNCPMMLXR-NEE
K4UBE3D4AA-MGCR
H9HCNNNFAMMLXR-NEE
MT53E2G32D4NQ-046 WT:A
MT53E512M32D1NP-046 WT:B
MT53E1G32D2NP-046 WT:B
BUG=b:197850509
TEST=build pass
Change-Id: Ib7bdab1396138d728ae053c30656a9c80dddaff8
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update the I2C ports and touchpad based on the schematic.
BUG=b:195622489, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I8778ad6564e526e029c46c36c78e38f764e3c6b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56998
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the USB port configuration based on driblee schematic.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 1
USB2 [3]: None
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: None
USB2 [7]: None
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: None
BUG=b:195622487, b:191732473
BRANCH=keeby
TEST=FW_NAME="driblee" emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id9f4f8db98cb20db1c3936c65689a847a7802b9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56997
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This takes the devicetree SPI settings and moves them into Kconfig.
BUG=b:195943311
TEST=boot guybrush & majolica and verify spi settings.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Icce1d57761465ae8255e5d9ce8679f3fdcb0ceed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add two thermal sensors for fan and wwan for DPTF based thermal control.
BRANCH=None
BUG=b:181271666
TEST=None
Change-Id: Idc9bd6040c9bb316ec7e314f5e9c937c75cfc95a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Boris Mittelberg <bmbm@google.com>
|
|
This will add ACPI information to enable WACOM touchscreen.
TEST=Boot DUT and issue command:
$ ls -al /sys/bus/i2c/devices
WACOM PWB-D893 device should be listed and touchscreen should be functional.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I37c0831485135fda3284dda6b61f4825b7fc51a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Add the support RAM parts for Corori.
Here is the ram part number list:
DRAM Part Name ID to assign
H9HCNNNBKMMLXR-NEE 0 (0000)
K4U6E3S4AA-MGCR 0 (0000)
lp4x-spd-1.hex # ID = 0(0b0000) Parts = H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR
BUG=b:196744958
BRANCH=keeby
TEST=emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ia11b5db145deeea838a8f5949accdb11e13342f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56988
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to schematics, TSR2 thermal sensor is not present in corori.
BUG=b:197281317
BRANCH=keeby
TEST=FW_NAME="corori" emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Id69f9d6ace738ef1e792addd782d05c2d03d2b3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57110
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Support Elan touchpad.
2. Follow schematic to disable I2C1, I2C2 and I2C3.
BUG=b:197052531
BRANCH=keeby
TEST=FW_NAME="corori" emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ideef57c275432e21f8580d4c5c937909b168d91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57031
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select the drivers for ALC5682 codec and MAX98360A spk amp
BUG=b:197037090
BRANCH=keeby
TEST=FW_NAME="corori" emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I0659a05fbcc28702d922a23d74885ba65a4254f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57015
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to modify USB port settings.
USB2 [0]: USB Type C Port 0
USB2 [1]: None
USB2 [2]: USB Type A Port 0
USB2 [3]: None
USB2 [4]: None
USB2 [5]: Camera UFC
USB2 [6]: None
USB2 [7]: Integrated Bluetooth
USB3 [0]: USB Type C Port 0 (M/B side)
USB3 [1]: None
USB3 [2]: USB Type A Port 0 (M/B side)
USB3 [3]: None
BUG=b:196998272
BRANCH=keeby
TEST=FW_NAME="corori" emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I2045b2be9d79bfd394fa4520faa0fb552a704206
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57010
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updated the GPIO pins based on the latest schematic.
BUG=b:196867404
BRANCH=keeby
TEST=FW_NAME=corori emerge-keeby coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I683a7da4fcb2e4e0efdb3547b1de15796c6b55e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the anahera variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:197850509
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_ANAHERA
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Id7649d56a8d6f85d12208f7ddaf2f71a7fe98e8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Ensure braces are consistent on all branches of a conditional statement,
as per the coding style.
Tested with BUILD_TIMELESS=1, Google Butterfly remains identical.
Change-Id: I34f3b22486e0f0712bc248477acb43012b21c5ee
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This keeps the default of EFS_SPI_SPEED at 66.66Mhz for the non-EM100
case, but switches the EFS_SPI_READ_MODE setting from Dual IO (1-1-2) to
Quad IO (1-1-4) for the non-EM100 case. This patch adds a special config
for the EM100 emulator case that has limited SPI frequency support.
Tested on Majolica by Martin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8996c2bf606ccd21686092beac8d96b22c0b7869
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56815
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make `mainboard_fill_spd_data` mandatory and adapt mainboards to define
this function accordingly.
Change-Id: Ic18c4c574e8c963bbb41c980f43bdbacc57735af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55806
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the `mainboard_fill_spd_data` function out of romstage, in
preparation to confine `pei_data` usage to as few files as possible.
Change-Id: I6447da4d135d920f9145e817bfb7f9056e09df84
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55805
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `pei_data` struct is already zero-initialised.
Change-Id: If539cddc007f32a04389bc3b3b06c43cb5c86e10
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55804
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Variants only need to provide the SPD index and whether said index
corresponds to a dual-channel configuration, which can be achieved
without using `pei_data`. Add two functions that return the values
and use them in `spd.c` at mainboard level.
Change-Id: I9bc4527057d4a771883c8cc60da2501516d6fb94
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
This patch enables SaGv support for primus.
BUG=b:196286180
Signed-off-by: Ariel Fang <ariel_fang@wistron.corp-partner.google.com>
Change-Id: I00074e348dd6347602c18dcfd231a890153b4685
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:187446498
TEST=Boot and verify memory trains at all the SaGv points through FSP
debug logs.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I883ae50b07e7b1d5554763fd79079d40b264b721
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add GPIO "rt1011 reset" and i2c2 initialization for RT1011.
Add CHERRY_USE_RT1011 and CHERRY_USE_RT1019 to Kconfig, so we can
spearate code for the specific codec by config.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Change-Id: I18939a2a2caae0444ce17f4712764647975121ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57157
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updated the GPIO pins based on the latest schematic.
BUG=b:191732473, b:195619827
BRANCH=keeby
TEST=FW_NAME=driblee emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I20baeb6b13c8c0a70c7555aa8f7f5557768c0083
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56996
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support to drawcia for MT53E512M32D1NP-046 WT:B.
This part is already in global_lp4x_mem_parts.json.txt, and use
/util/spd_tool/lp4x/gen_part_id to assigns DRAM IDs.
BUG=b:196951879
BRANCH=firmware-dedede-13606.B
TEST=FW_NAME=drawcia emerge-dedede coreboot chromeos-bootimage
Change-Id: Ic42e6357943ba651ffd92fb2974e9ea52fa19020
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56905
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
commit df520855 (soc/intel/jsl: Add disable_external_bypass_vr config)
Add FW_CONFIG probe for don't stuffing ANPEC APW8738BQBI IC.
BUG=b:190727416
BRANCH=dedede
TEST=test for enter S0ix and resume normally by powerd_dbus_suspend
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I15ab30f14df9dc02157009091aa8398e2fa75188
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56804
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add CBI sku RAM ID 5 for 4GiB Capacity with dual channel and dual rank
with 4gb dram density.
BUG=b:178665760
BRANCH=Octopus
TEST=build fw and flash to the dut with RAMID 5, dut can boot up successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I922a518cffc4dac71caec68e6f7a55c6c5717438
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56982
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override USB port configurations based on the latest bugzzy schematics.
BUG=b:192521391
BRANCH=None
TEST=Built test coreboot image
Change-Id: I4368946f4175f4f065a3483dc7ca6068c6de3123
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
WWAN_PERST_L (GPP_E0) is wrongly configured to NC in ramstage.
So, remove it.
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: If8e96045a0d78a942f77d8d8e371ab75dff0c202
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
4 MAX98390 Speaker Amps are connected to i2c0 and device addresses are
0x38/0x39/0x3a/0x3b
BUG=b:191931762
TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ie8f01e6a7e09e18f6d34f3ceb1db8e2e238197bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57114
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sounds like we prefer to have this under drivers/ instead of device/.
Also move all MIPI-related headers out from device/ into their own
directory.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib3e66954b8f0cf85b28d8d186b09d7846707559d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Create the dewatt variant of the guybrush reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:196460993
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_DEWATT
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: I57860a7cad1bf202bd3ef3eed5f498fbf1d29af8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57108
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3bea9e1f9cc25a4476ddbaa8bd8e434609eb28f7
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Iec6ec8bbf3cc5c9230ba6bcb0126ff6085f26464
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
1. According to the Maxim's comment and schematic diagram of proto, Modify I2C slave address to 0x38, 0x3c.
2. According to the schematic diagram of proto, Change GPD11 to NC.
BUG=b:191811888, b:1191213263
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ibf8adf2ed8dda9ae6da06e7e995bef9395cdee35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57059
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Touchscreen will be no function with R93-14092.19.0 image or be later.
It just happened to work because elants_i2c driver would bind
to the device first based on "ELAN0001" HID ID
BUG=b:195994810
TEST= verify only update RW FW can fix touchscreen no function issue
1.Build test firmware
2.prepare DUT enviroment (R93 image + update RW to test firmware)
3.verify touchscreen function normally
Signed-off-by: FrankChu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: Ie9e0fe726854d0128ad1bb430544640dc8f034ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: I06d8a543dbd77137cb97c4ea695a1f2b9f8ee76c
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57116
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I45ecab8c036a7e75cc0c564867119c027175ed06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Primus has MX98360A, which Linux kernel 5.10 currently does not support
and, therefore, audio does not work. As the device is compatible with
the MX98357A, use that until Linux’ SoF driver supports the new version
(https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/3070268).
BUG=b:194749863
BRANCH=none
TEST=build coreboot and audio function works
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I893d9a31dc2c7726599c150be01b9585fb6c8a47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Commit e7f3e6a0558 added PL4 limits for brya0, but the units were mW,
whereas the `tdp_pl4` field is expected to be in whole Watts, therefore
divide all of the settings by 1000.
BUG=b:197468828
TEST=boot brya0 to OS
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6da6bae4eb8c83188d813828cdc4f7c1e20f1b5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Init basic override devicetree based on schematics
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I283517427612e24eabe2ce736d677253065c7859
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch enabled the SaGv support for brya0 baseboard.
BUG=b:187446498
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I2a71e159fa49f677660af8279f2b582a3916eee2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable DRIVERS_GENESYSLOGIC_GL9755 support for primus.
BUG=b:195611000
BRANCH=None
TEST=build pass
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I0c60979a2d42f836e0f0261c42fcfc36c41e113a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add G2Touch G7500 touchscreen into devicetree for cret.
BUG=b:180547621
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I57638bf8a3eb4efcd819f5433fa54c22b7af3054
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add the support RAM parts for felwinter.
Here is the ram part number list:
DRAM Part Name ID to assign
K4U6E3S4AA-MGCR 0 (0000)
K4UBE3D4AA-MGCR 1 (0001)
H9HCNNNBKMMLXR-NEE 0 (0000)
MT53E1G32D2NP-046 WT:A 2 (0010)
BUG=b:197308861
BRANCH=None
TEST=emerge-brya coreboot
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I76febefc251b02a047819242e23c02dc50891c2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 68d8357dab55660058ad1ab8dca34fd03e0adbb5.
Reason for revert: Device NVS is expected by mainboard samus
in payload depthcharge:
https://chromium.googlesource.com/chromiumos/platform/depthcharge/+/932c6ba2704987c0db64dbdfe03c158482c7ab11/src/board/samus/board.c#60
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Icb5fa6da3412a51aae56c3658163e5b98d57bab3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the moonbuggy variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=191356135
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_MOONBUGGY
Signed-off-by: Rehan Ghori <rehang@google.com>
Change-Id: Iaf545dcd5ff537afdf029f510553d16a1239763e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
gooey is the same design as boten, and differs only in replacing Cr50
with discrete TPM.
BUG=b:193366710, 197247706
TEST=FW_NAME=gooey emerge-keeby coreboot
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I2a54f872a7d5c0bee76a9e6e309613d9357b380b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
