| Age | Commit message (Collapse) | Author |
|---|
|
Set the `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag to request End-Of-Post
right after PCI enumeration and handle the command response at
`BS_PAYLOAD_BOOT'.
With these settings we have observed a boot time reduction of about 20
to 30 ms on brya0.
BUG=b:268546941
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post after PCI initialization and EOP message received at
`BS_PAYLOAD_BOOT'.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Ib850330fbb9e84839eb1093db054332cbcb59b41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74215
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
coreboot supports three instances of sending EOP:
1. At CSE `.final' device operation
2. Early as with Alder Lake in chip_operations.init if
`SOC_INTEL_CSE_SEND_EOP_EARLY' is selected
3. At BS_PAYLOAD_BOOT as designed for Meteor Lake if
`SOC_INTEL_CSE_SEND_EOP_LATE' is selected
Currently, Alder Lake uses #3 as it results in better and more stable
boot time. However, what would deliver even better result is to not
actively wait for CSE completion.
This patch introduces a new `SOC_INTEL_CSE_SEND_EOP_ASYNC' Kconfig
which split the action of sending EOP request and receiving EOP
completion response from the CSE.
This patch used in conjunction with #1 can significantly
improves the overall boot time on a Raptor Lake design. For example
`SOC_INTEL_CSE_SEND_EOP_ASYNC' on a skolas board can deliver up to 36
ms boot time improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 1 | 1020.052 | 971.272 |
| 2 | 1015.911 | 971.821 |
| 3 | 1038.415 | 1021.841 |
| 4 | 1020.657 | 993.751 |
| 5 | 1065.128 | 1020.951 |
| 6 | 1037.859 | 1023.326 |
| 7 | 1042.010 | 984.412 |
|----------+----------+-----------|
| Mean | 1034.29 | 998.20 |
| Variance | 4.76 % | 5.21 % |
The improvement is not stable but comparing coreboot and FSP
performance timestamps demonstrate that the slowness is caused by a
lower memory frequency (SaGv point) at early boot which is not an
issue addressed by this patch.
We also observe some improvement on an Alder Lake design. For example,
the same configuration on a kano board can deliver up to 10 ms boot time
improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 0 | 1067.719 | 1050.106 |
| 1 | 1058.263 | 1056.836 |
| 2 | 1064.091 | 1056.709 |
| 3 | 1068.614 | 1055.042 |
| 4 | 1065.749 | 1056.732 |
| 5 | 1069.838 | 1057.846 |
| 6 | 1066.897 | 1053.548 |
| 7 | 1060.850 | 1051.911 |
|----------+----------+-----------|
| Mean | 1065.25 | 1054.84 |
The improvement is more limited on kano because a longer PCIe
initialization delays EOP in the Late EOP configuration which make it
faster to complete.
CSME team confirms that:
1. End-Of-Post is a blocking command in the sense that BIOS is
requested to wait for the command completion before loading the OS or
second stage bootloader.
2. The BIOS is not required to actively wait for completion of the
command and can perform other operations in the meantime as long as
they do not involve HECI commands.
On Raptor Lake, coreboot does not send any HECI command after
End-Of-Post. FSP-s code review did not reveal any HECI command being
sent as part of the `AFTER_PCI_ENUM', `READY_TO_BOOT' or
`END_OF_FIRMWARE' notifications.
If any HECI send and receive command has been sent the extra code
added in `cse_receive_eop()' should catch it.
According to commit 387ec919d9f7 ("soc/intel/alderlake: Select
SOC_INTEL_CSE_SEND_EOP_LATE"), FSP-silicon can sometimes (on the first
boot after flashing of a Marasov board for instance) request coreboot
to perform a global request out of AFTER_PCI_ENUM notification. Global
request relies on a HECI command. Even though, we tested that it does
not create any issue, `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag should not
be associated to the `SOC_INTEL_CSE_SEND_EOP_EARLY' flag to prevent
potential a global reset command to "conflict" with the EOP command.
This patch also introduces a new code logic to detect if CSE is in the
right state to handle the EOP command. Otherwise, it uses the
prescribed method to make the CSE function disable. The typical
scenario is the ChromeOS recovery boot where CSE stays in RO partition
and therefore EOP command should be avoided.
[DEBUG] BS: BS_PAYLOAD_LOAD exit times (exec / console): 0 / 14 ms
[INFO ] HECI: coreboot in recovery mode; found CSE in expected
SOFT TEMP DISABLE state, skipping EOP
[INFO ] Disabling Heci using PMC IPC
[WARN ] HECI: CSE device 16.0 is hidden
[WARN ] HECI: CSE device 16.1 is disabled
[WARN ] HECI: CSE device 16.2 is disabled
[WARN ] HECI: CSE device 16.3 is disabled
[WARN ] HECI: CSE device 16.4 is disabled
[WARN ] HECI: CSE device 16.5 is disabled
BUG=b:276339544
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with and `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post sent soon after FSP-s and EOP message receive at
`BS_PAYLOAD_BOOT'. Verify robustness by injecting a
`GET_BOOT_STATE' HECI command with or without `heci_reset'. The
implementation always successfully completed the EOP before
moving to the payload. As expected, the boot time benefit of the
asynchronous solution was under some injection scenario
undermined by this unexpected HECI command.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I01a56bfe3f6c37ffb5e51a527d9fe74785441c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This function calls into `set_feature_ctrl_lock()` to lock
IA32_FEATURE_CONTROL MSRfeature control.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9a03ee6786144dae6fd3a18bcc53cb62919dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This function calls into `set_feature_ctrl_vmx_arg()`
to enable VMX for virtualization if not done by FSP (based on
DROP_CPU_FEATURE_PROGRAM_IN_FSP config is enabled) in MeteorLake
SoC based platform.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7e49c15fd4f78a3e633855fea550720f0a685062
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This function performs locking of the AES-NI enablement state.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I16f1c14d8a0ca927a34c295cb95311bd4972d691
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch calls into API to disable 3-strike error on
Meteor Lake SoC based platform.
TEST=Able to build and boot google/rex to ChromeOS.
Dumping MSR 0x1A4 shows BIT11 aka 3-strike error is disabled
```
localhost ~ # iotools rdmsr 0 0x1a4
0x0000000000000900
```
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5c33a1fa2d7e27ec8ffdea876edbb86adc3b45b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch introduces a new config named
`DROP_CPU_FEATURE_PROGRAM_IN_FSP` to avoid FSP running basic CPU
feature programming on BSP and on APs using the "CpuFeaturesPei.efi"
module.
Most of this feature programming is getting performed today in scope
of coreboot doing MP Init. Running this redundant programming in
scope of FSP (when `USE_FSP_FEATURE_PROGRAM_ON_APS` config is enabled)
results in CPU exception (for example: attempting to reprogram CPU
feature lock MSR is causing CPU exception).
SoC users should select this config after dropping "CpuFeaturesPei.ffs"
module from FSP-S Firmware Volume (FV). Upon selection, coreboot runs
those additional feature programming on BSP and APs.
This feature is by default enabled, in case of "coreboot running MP
init" aka `MP_SERVICES_PPI_V2_NOOP` config is selected.
At present, this option does not do anything unless any platform
eventually decides to drop FSP feature programming module and choose
coreboot CPU feature programming over it.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3be5329390401024d7ec9eed85a5afc35ab1b776
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
In Intel designs, internal processor errors, such as a processor
instruction retirement watchdog timeout (also known as a 3-strike
timeout) will cause a CATERR assertion and can only be recovered from by
a system reset.
This patch prevents the Three Strike Counter from incrementing (as per
Intel EDS doc: 630094), which would help to disable Machine Check Catastrophic error. It will provide more opportunity to collect more useful CPU traces for debugging.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I286037cb00603f5fbc434cd1facc5e906718ba2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74158
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Restrict DPTC to 15W boards, since we only have 15W values defined in
the devicetree. This will revert the 6W boards back to their default
values, rather than (incorrectly) configuring them with 15W values.
BUG=b:253301653
TEST=Verify DPTC values are set for 15W boards
TEST=Verify DPTC values are set not set for 6W boards
Change-Id: I94f3974fce6358e3cbb0c30c1af33eb7ecb29ad7
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74127
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP will return the TDP in the format 0xX0000, where 'X' is the
value we're interested in. For example: 0xF0000 (15W), 0x60000 (6W).
Re-interpret the value so the caller just sees the TDP directly, without
needing to re-interpret things themselves.
BUG=b:253301653
TEST=Manually verify value is correct
Change-Id: I632e702d986a4ac85605040e09c1afab2bbdc59d
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74126
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is needed to generate MADT and SRAT where lapicid for threads need
to be added last. When CPUID leaf '0xB' is not present assume some
defaults that would result in identical ACPI code generation.
Change-Id: I2210eb9b663dd90941a64132aa7154440dc7e5a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69222
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On some systems the BSP cannot know how many CPUs are present in the
system. A typical use case is a multi socket system. Setting the enable
flag only on CPUs that actually exist makes it more flexible.
Change-Id: I6c8042b4d6127239175924f996f735bf9c83c6e8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68892
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Don't pass the stub params to the mp_init code.
Change-Id: I070bc00ae5e5bceb6c5b90ea833cc057dd41f6cc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64802
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In the current design the relocatable parameters are used to know the
offset of the 32bit startpoint. This requires back and forward
interaction between the stub, the loader and the mp init code. This
makes the code hard to read.
This is static information known at buildtime, so a better way to deal
with this is to generate a header that contains this offset.
Change-Id: Ic01badd2af11a6e1dbc27c8e928916fedf104b5b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64625
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's quite confusing to keep track of lapic ID inside the device
struct and initial lapic ID inside an array.
Change-Id: I4d9f8d23c0b0e5c142f6907593428d8509e4e7bb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64342
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently this is only used in bootblock and expects a fixed offset.
Change-Id: I3c4db6fffe3343f12383fe9585620ffefb01cf81
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
It will cache decoded EDID string in a static array. If called more
than once, a pointer to the static array is directly returned, without
reading EDID again.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ibdbe4d76f9b59e7ae83b60cda042c2d1c39827ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74180
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Drop devicetree setting X2apic as the same functionality is already
exposed in Kconfig.
To activate X2apic select X2APIC_ONLY or X2APIC_RUNTIME in
the "APIC operation mode".
Note: Your OS must have support for X2APIC. If you are using less
than 256 CPU cores select XAPIC_ONLY here.
Test:
- Booted to OS in X2APIC mode when X2APIC_ONLY or X2APIC_RUNTIME
was selected.
- Booted to OS in XAPIC mode when XAPIC_ONLY was selected.
Change-Id: I65152b0696a45b62a5629fd95801187354c7a93b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
When more than 255 CPU cores are present on a board
the X2APIC must be used.
Select DEFAULT_X2APIC_RUNTIME to support X2APIC by
default when a mainboard enables it in the devicetree.
Change-Id: I3e84cfbd2a7f05b142dc4d782764edce81646c8a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74184
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch renames debug FMD file (chromeos.debug-fsp.fmd) to
chromeos-debug-fsp.fmd in order to match the file path name in `FMDFILE`
config.
TEST=Able to build intel/mtlrvp with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic8de07e4befa6b1ab8ab57d593c6939d87c48e9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Because Markarth PCIe port 1 use for eMMc not SD. So we need override
PCIe config for Markarth. And also the Markarth have NVMe and eMMC
SKU. Follow Winterhold to look at the NVMe CLKREQ signal before
initializing the ports allowing us to identify which device is populated
and only initialize that device.
BRANCH=none
BUG=b:275669215
TEST=emerge-skyrim coreboot chromeos-bootimage
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I0b4e4067a30019d742c7589a52badf93b7091615
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74133
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Inject ACPI code for all generated ASL templates.
This fixes ACPI errors shown in linux when not all sockets
are currently plugged in or some have been disabled.
Test:
Boot Archer City with CONFIG_MAX_SOCKET=4
Change-Id: I9562a37a92c6140a5623db3c8fb5972e6a90aaa4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74183
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
|
|
The RTD3 driver should have its 'use_rp_mutex' set in the devicetree.
BRANCH=firmware-brya-14505.B
TEST=boot to OS and check the generated SSDT table for the WWAN
The RTD3 RPMX mutex should be used in the reset Methods
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ic3fe20c56b67c2b5177f55f4845610087a30dc7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73381
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
When 'use_rp_mutex' (default = 0) is set in the device tree, a root
port mutex will be added. This mutex is used in _ON and _OFF method,
where the GPIO reset and/or enable GPIO value is changed. The
companion driver, such as WWAN driver, needs to acquire this root
port mutex when accessing the same GPIO pins. Using this common mutex
prevents those invoked methods from being called from different thread
while one is not completed.
An example is that WWAN driver calling _RST method to reset the device
and does remove/rescan for the device while the pm runtime work might
call RTD3 _OFF.
For those root port without additional driver, this mutex is not needed.
BRANCH=firmware-brya-14505.B
TEST=boot to OS and check the generated SSDT table for the root port.
The RPMX mutex should be generated and _ON and _OFF should use this
mutex.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ibc077528692b2d7076132384fb7bd441be502511
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
On Skyrim, there isn't a need for a sleep GPIO table. Remove the TODO
and filler table and function to reduce unnecessary function overhead.
BUG=None
BRANCH=Skyrim
TEST=Build Skyrim BIOS image.
Change-Id: Ia9d55a5e2295bb2e2c2957c4f5207362f616022c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
IF its first call is get_blc_pwm_freq_value(NULL), null dereference
will occur.
Now when the parameter is NULL, it will return the value of the static
blc_pwm_freq directly, so the original behavior is kept.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I32354aa0fe1a3ca725c2031f973ffad0bda81ad5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This reverts commit e7a1204f26fe3628de99b4ab4e3f32916565b95c.
This initial change was causing a boot failure when transitioning into
recovery mode.
BUG=b:276927816
TEST='emerge-brya coreboot chromeos-bootimage', flash and boot a skolas
SKU1 to kernel, then press Esc-Refresh-PowerButton to try to reboot into
recovery mode.
Change-Id: Ibebb20a000a239c344af1c96b8d376352b9c774e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74207
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 11f2f88a277124713f7b0023f078fcc2e1a98c32.
Revert initial change as it was causing a boot failure when
transitioning into recovery mode.
BUG=b:276927816
TEST='emerge-brya coreboot chromeos-bootimage', flash and boot a skolas
SKU1 to kernel, then press Esc-Refresh-PowerButton to try to reboot into
recovery mode.
Change-Id: I91c8d0434a2354dedfa49dd6100caf0e5bfe3f4c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74206
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the mode_switch.S
compilation unit to all stages that run on the x86 cores, but not to
verstage on PSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8950375d31557d9a38169869c1d250417261c31c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Use the 'verstage_x86' make target for the mode_switch.S compilation
unit instead of making adding it to the 'verstage' target depending on
VBOOT_STARTS_BEFORE_BOOTBLOCK not being selected. The only case where
VBOOT_STARTS_BEFORE_BOOTBLOCK is selected is the verstage on PSP case,
so I find using the 'verstage_x86' target here a bit easier to
understand.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab618d4b9e325b07a648b91fcdce99c63644fbfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74196
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless build for Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23c6977ae8acebb8dcd546f86f7f7b677272a6cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74153
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless build for Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I181c3207bb1ebe9c5080ef3a3cdda8146ed05822
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74152
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless builds for Mandolin without verstage on PSP and Guybrush
with verstage on PSP result in identical images with and without this
patch applied.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94de6de5a4c7723065a4eb1b7149f9933ef134a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74151
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add the required CMOS entries for the mirror flag, so that it can
be enabled from a defconfig.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I174ac896df050480ee90c8141c5536b628c98432
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73682
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When enabled, the EC will mirror the firmware contained inside the
coreboot ROM. This allows it to be updated at the same time as
coreboot.
Enable the mirror flag if the installed EC firmware does not match
the target version or if a CMOS option, "manual_mirror_flag" is
set.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I377abbb37dc4d3e535e518a73e73969b25967daa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Some third-party SSDs, from Samsung and WD, such as the 990 Pro and
WD Black 850X aren't initialised by coreboot, seemingly as coreboot
is too quick; debug builds work, and enabling hotplug does.
Add a cmos option `pci_hot_plug`, defaulting to enabled to allow these
SSDs to work.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I680211bc87153a5e6005d58040a94725c0973451
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
ASPM is already configured by FSP so disable it in coreboot to
reduce boot time by a whopping 34ms.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I073c68dafa9baa90e253b5230f84b0de6a7e5c47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73982
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ic228b869aea362c1f07e0808c2735ff3b285a6bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73980
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This was added to solve Debian 10 not booting. Debian 10, which
now isn't the latest stable version works, so remove the
workaround that was included in the original port.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic11f355eb218ff3bad00fff83537c99c1b6985bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72669
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Alder Lake (ADL) and Raptor Lake (RPL) dptf settings for omnigul
BUG=b:273415170
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I8280f82ff1534ea63bcb448da231712bb4abd6d3
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This reverts commit ac69ce91229dee68d4135c596f49cf9e5efbe1e9.
Reason for revert: Removing breaks suspend in kernels > 6.2 and
Windows.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3e90266e66192b328b9af51c5e614774a248ddf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
Enables pre-cpu boot timestamps from cse.
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Boot on rex, check "cbmem -t"
Change-Id: I68cd53c18af6a400bcd9dc15d428a904b0647495
Signed-off-by: Bora Guvendik <bora.guvendik@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73759
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table.
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Able to see TS elapse prior to IA reset on Rex
Change-Id: I548cdc057bf9aa0c0f0730d175eaee5eda3af571
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73713
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Boot to OS, check cbmem -t
Change-Id: I4d2da820f39c40ea864d15d25a94a68497b2af3d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74047
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CSE performance data timestamps are different for version 1
Alder Lake/Raptor Lake and version 2 Meteor Lake. This patch
moves the current ADL/RPL timestamp definitions to a separate
header file. It marks current structure as version 1.
BUG=b:259366109
TEST=Boot to OS, check ADL/RPL pre-cpu timestamps.
Change-Id: I780e250707d1d04891a5a1210b30aecb2c8620d3
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73712
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
This patch updates the MTLRVP flash layout to allow CSE Lite FW
update and accommodate multiple ESx SoC stepping blobs.
SI_BIOS:
SI_EC: Removed
RW_SECTION_A/B: Increased by ~1.9MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
Additionally, moved RW_LEGACY under extended BIOS region.
For chromeos-debug-fsp.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.2MB.
RW_LEGACY: Dropped
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
BUG=b:271407315
TEST=Able to enable CSE update on MTLRVP and have free space
to add one more PUNIT FW to support different SoC stepping.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I8cfba861e6d3122b0795a5a8e589c67cebad9762
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73378
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
Debug FSP is ~920KiB larger than release FSP and we don't have
sufficient space for MTL-P RVP flash layout.
Remove RW_LEGACY and split them into RW_SECTION_A/B so we can have a
room for it.
BUG=b:271407315
TEST=Build intel/mtlrvp with CONFIG_BUILDING_WITH_DEBUG_FSP.
Change-Id: Ief7dd39af018c4c1519ca80d1303085d8298cda6
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74193
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
Use the introduced EFI variable store driver on top of the SMMSTORE
region in SPI flash to read/write options.
Change-Id: I520eca96bcd573f825ed35a29bf8f750e313a02d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62562
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a driver to read and write EFI variables stored in a region device.
This is particularly useful for EDK2 as payload and allows to reuse
existing EFI tools to set/get options used by the firmware.
The write implementation is fault tolerant and doesn't corrupt the
variable store. A faulting write might result in using the old value
even though a 'newer' had been completely written.
Implemented basic unit tests for header corruption, writing existing
data and append new data into the store.
Initial firmware region state:
Initially the variable store region isn't formatted. Usually this is
done in the EDK2 payload when no valid firmware volume could be found.
It might be useful to do this offline or in coreboot to have a working
option store on the first boot or when it was corrupted.
Performance improvements:
Right now the code always checks if the firmware volume header is valid.
This could be optimised by caching the test result in heap. For write
operations it would be good to cache the end of the variable store in
the heap as well, instead of walking the whole store. For read
operations caching the entire store could be considered.
Reclaiming memory:
The EFI variable store is append write only. To update an existing
variable, first a new is written to the end of the store and then the
previous is marked invalid. This only works on PNOR flash that allow to
clear set bits, but keep cleared bits state.
This mechanisms allows a fault tolerant write, but it also requires to
"clean" the variable store for time to time. This cleaning would remove
variables that have been marked "deleted".
Such cleaning mechanism in turn must be fault tolerant and thus must use
a second partition in the SPI flash as backup/working region.
For now to cleaning is done in coreboot.
Fault checking:
The driver should check if a previous write was successful and if not
mark variables as deleted on the next operation.
Tested and working:
- Enumerate all existing variables
- Read variables
- Write variables
Change-Id: I8079f71d29da5dc2db956fc68bef1486fe3906bb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52564
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch avoids creating runtime ACPI for unused WIFI solutions.
For example: if the Rex SKU is with WIFI_CNVI then you don't need
to populate ACPI code for WIFI_PCIE.
FW_CONIG can be used for making those decisions.
TEST=No ASL entries being created for WIFI_PCIE if the FW_CONIG is
set to WIFI_CNVI.
Also, helped to save the boot time on google/rex (FSP-S API) by 9ms.
Change-Id: I60e4332d8d8c360fdf425b30513ff79209979e85
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74147
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Fix a typo in an enum's type name, "tmp" ---> "tpm". The enum type is
not used anywhere in the coreboot tree.
Change-Id: Ie7529e7ee80aa9661ec053da8211c2c3295b3942
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The i2c.c compilation unit is added to all stages in all cases, so use
the all target instead of adding it to all stages separately. Also order
the all targets alphabetically.
TEST=Timeless build on Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie90380075a3c87d226cdcb0f41f7e94275eaaa42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Glinda and Phoenix have different requirements, so split the birman
port_descriptors file to betty apply to each SoC.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia28cf4172b6adada10809e0135b2459077fa3da0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Set Type-A USB3 port0/1 tx_de_emp to 0x2B to fix the USB3 Gen2
RX signal integrity issue.
BUG=None
TEST=build FW and check Type-A USB3 port0/port1 RX pass
Change-Id: I9296ae5a8a9d7aa49b3c7529a9c1b2d2829b15d0
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
The Intel Power and Performance (PnP) team requested to update the
following:
- TDC settings for RPL-U 15W variant should be 22A.
- TDC settings for RPL-P 28W variant should be 33A.
BUG=b:275694022
BRANCH=firmware-brya-14505.B
TEST=PnP validated performance impact with these settings on both
RPL-U 15W and RPL-P 28W
Change-Id: I1141414785a990b975e32ebc03e490b83082aab7
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74046
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Baieswara Reddy Sagili <baieswara.reddy.sagili@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add CPU power limits support and values for RPL on Hades
BUG=b:269371363
TEST=builds
Change-Id: I22ef56152abe5a23067c5e923b07d60dc9fac8e7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73895
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CBFS location in memory is different than on the real hardware.
Change-Id: Icd806a57f449042c883b624056c05c1ff7e4c17e
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
|
|
Add override devicetree based on schematics(ver. 20230308).
BUG=b:272829190
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I9cd918c6a48cc6007a18c5aa94afe31fd9608718
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73974
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
The patch defines acpi_set_cpu_apicid_order() which orders the APIC IDs
based on APIC IDs of Performance cores and Efficient cores, calculates
the total core count and total Performance cores count, populates the
information in the cpu_apicid_order_info struct.
The helper function useful to present the Performance and Efficient
cores in order to OS through MADT table and _CPC object.
TEST=Verify the build for Gimble (Alder Lake board)
Change-Id: I8ab6053ffd036185d74d5469fbdf36d48e0021ce
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72131
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to document 640858 MTL EDS Vol2, bit 18 (PWR_PERF_PLATFRM_OVR) of MSR_POWER_CTL must be set.
This patch is backported from
`commit 117770d32468e63df ("soc/intel/
alderlake: Enable Energy/Performance Bias control")`.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic83225b619c49db0b49b521a83a2f1dc1ad69be8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74155
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates energy performance preference value to all logical CPUs
when the corresponding chip config is true.
This patch is backported from
`commit 0bb2225718ef898c ("soc/intel/alderlake: Add EPP override
support")`.
BUG=b:266522659
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8172276159fe3987dae36ec30ebceb76dd0ef326
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74154
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Indent with tabs for the sake of consistency with the rest of the code.
Change-Id: Ibd325a7a8348cc1f9023e54dceab40d02a0df233
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Add the 28W TDP version of the ADL-P with MCHID 0x4629.
Verified that all 28W SoCs have the same PL1/PL2 defined
in Intel document #655258 "12th Generation Intel Core
Processors Datasheet, Volume 1 of 2".
Fixes the error seen in coreboot log:
[ERROR] unknown SA ID: 0x4629, skipped power Limit Configuration
Change-Id: Iad676f083dfd1cceb4df9435d467dc0f31a63f80
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
This patch adds FW_CONFIG to accommodate different Rex BoM
components across various SKUs.
1. Fingerprint sensor - FP Present/Absent
2. Ultra wideband - UWB Absent/Using BITBANG/Using GSPI1
3. WIFI - CNVi/PCIe
TEST=Able to build and boot google/rex.
Change-Id: I97b0dc25f239103a0a235f14b50008a633e2f88d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
This patch updates the Rex flash layout to allow CSE Lite FW
update and accommodate multiple ESx SoC stepping blobs.
For default chromeos.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.9MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
Additionally, moved RW_LEGACY under extended BIOS region.
For chromeos-debug-fsp.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.2MB.
RW_LEGACY: Dropped
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
BUG=b:262868089
TEST=Able to enable CSE update on google/rex and have free space
to add one more PUNIT FW for support different SoC stepping.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6146b36c4ce2c0141277eeb906d6ad1f503f3c78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
tsc_freq.c gets built into all stages, but the tsc_freq_mhz function it
implements calls the get_pstate_0_reg function which was only built into
ramstage. Since tsc_freq_mhz was only called in ramstage, commit
2323acab6a7a ("soc/amd/stoneyridge: implement and use get_pstate_0_reg")
didn't cause the build to fail, but better factor out the P-state-
related utility functions into a separate compilation unit and include
it in all stages that also include tsc_freq.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id3a3ee218f495be5e60a888944487704e7e8a1a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
monotonic_timer.c, tsc_freq.c and uart.c get added to all stage targets,
so just add those to the all stage targets. They still need to be added
to the smm stage target, since the all target doesn't add things to the
smm stage.
TEST=Timeless build results in identical image for Gardenia.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I16c02bc0ff54553f212b94d110abef6a7bdedbb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74144
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI support for Sapphire Rapids. Passes FWTS ACPI tests.
The code was written from scratch because there are Xeon-SP specific
implementation especially Integrated Input/Output (IIO).
Change-Id: Ic2a9be0222e122ae087b9cc8e1859d257e3411d6
Signed-off-by: Jonathan Zhang <jonzhang@meta.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71967
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Debug FSP is ~920KiB larger than release FSP and we don't have
sufficient space for rex flash layout.
Remove RW_LEGACY and split them into RW_SECTION_A/B so we can have a
room for it.
Note: This fmd will only used for internal testing/debugging and not for
the firmware in released devices.
BUG=b:262868089
TEST=Build google/rex with CONFIG_BUILDING_WITH_DEBUG_FSP.
Change-Id: I58b0af9c43c5d096dc80084497b39f13f67c25cd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Intel FSP has "debug" build which is not public, used for debugging by
approved developers. Add a Kconfig to indicate that coreboot is building
with debug version of FSP so we can adjust few things (i.e. flash
layout) in the case.
BUG=b:262868089
TEST=Able to build and boot google/rex.
Change-Id: I5555a2ab4182ad0036c42be6fea3d934ffd0db8c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
PortUsb30Enable has been overridden unexpectedly, this patch fixed it.
BUG=b:276181378
Test=boot to rex and check USB3 ports are working.
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: Ic04b9eb236ed28a76ee516c52fc0c983cb8f2c0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The patch enables addition of core_type member to 'struct cpu_info'
for MeteorLake platform.
TEST=Build and verify the code for Rex
Change-Id: I01abed6b87bec2f8eb39bfc941faff070b83abe6
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74130
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Now that only one build target per stage is included in the build
depending on CONFIG_SOC_AMD_COMMON_BLOCK_TSC being set, don't use a
separate ifeq block for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id9e551b37707081eb2ea1d682013f57c7ca8aabd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74017
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All AMD SoCs with Zen-based CPU cores are already using timestamps based
on the TSC counter, so use the existing common infrastructure instead of
reimplementing it in a similar way.
The behavior of the code changes slightly, but results in identical
timestamps. The timestamp_get implementation in soc/amd/common/block/cpu
divided the result of rdtscll() in timestamp_get by the result of
tsc_freq_mhz() and didn't override the weak timestamp_tick_freq_mhz
implementation that returns 1. The non AMD specific code returns the
result of rdtscll() in timestamp_get, but returns tsc_freq_mhz() instead
of 1 in timestamp_tick_freq_mhz, so we still get the correct timestamps.
TEST=The raw timestamps printed on the serial console are now multiplied
by the expected factor of the TSC frequency in MHz.
TEST=Normalized timestamps printed on the serial console by the x86 code
don't change significantly on Mandolin when comparing before and after
this patch. A slight variation in the timestamps is expected. An example
would be:
Before: CPU_CLUSTER: 0 init finished in 630 msecs
After: CPU_CLUSTER: 0 init finished in 629 msecs
TEST=The calculations of the time spent in verstage on PSP before
entering the bootblock on Guybrush result in similar times when
multiplying the value before the patch with the TSC frequency in the
case with the patch applied. The raw values printed on the serial
console by the verstage on PSP use the 1us time base, but the timestamp
logs that end up in CBMEM will be fixed up to use the same time base as
the x86 part of coreboot.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I57b732e5c78222d278d3328b26bb8decb8f4783e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Having L1.2 enabled on the SD port increases the kernel resume times by
between 30 & 40ms. This patch disables L1.2 on SD to get that time
back.
As with needing to have hotplug enabled on the SD card, this seems like
a driver issue, so hopefully that will get sorted out and this patch
can be reverted.
BUG=b:274025743
TEST=resume times are decreased.
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2c409fa2cd66c712c5ba7104635499d63fa0d2be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set the `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag to request End-Of-Post
right after PCI enumeration and handle the command response at
`BS_PAYLOAD_BOOT'.
With these settings we have observed a boot time reduction of about 20
to 30 ms on brya0.
BUG=b:268546941
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post after PCI initialization and EOP message received at
`BS_PAYLOAD_BOOT'.
Change-Id: I81e9dc66f952c14cb14f513955d3fe853396b21c
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73922
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot supports three instances of sending EOP:
1. At CSE `.final' device operation
2. Early as with Alder Lake in chip_operations.init if
`SOC_INTEL_CSE_SEND_EOP_EARLY' is selected
3. At BS_PAYLOAD_BOOT as designed for Meteor Lake if
`SOC_INTEL_CSE_SEND_EOP_LATE' is selected
Currently, Alder Lake uses #3 as it results in better and more stable
boot time. However, what would deliver even better result is to not
actively wait for CSE completion.
This patch introduces a new `SOC_INTEL_CSE_SEND_EOP_ASYNC' Kconfig
which split the action of sending EOP request and receiving EOP
completion response from the CSE.
This patch used in conjunction with #1 can significantly
improves the overall boot time on a Raptor Lake design. For example
`SOC_INTEL_CSE_SEND_EOP_ASYNC' on a skolas board can deliver up to 36
ms boot time improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 1 | 1020.052 | 971.272 |
| 2 | 1015.911 | 971.821 |
| 3 | 1038.415 | 1021.841 |
| 4 | 1020.657 | 993.751 |
| 5 | 1065.128 | 1020.951 |
| 6 | 1037.859 | 1023.326 |
| 7 | 1042.010 | 984.412 |
|----------+----------+-----------|
| Mean | 1034.29 | 998.20 |
| Variance | 4.76 % | 5.21 % |
The improvement is not stable but comparing coreboot and FSP
performance timestamps demonstrate that the slowness is caused by a
lower memory frequency (SaGv point) at early boot which is not an
issue addressed by this patch.
We also observe some improvement on an Alder Lake design. For example,
the same configuration on a kano board can deliver up to 10 ms boot time
improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 0 | 1067.719 | 1050.106 |
| 1 | 1058.263 | 1056.836 |
| 2 | 1064.091 | 1056.709 |
| 3 | 1068.614 | 1055.042 |
| 4 | 1065.749 | 1056.732 |
| 5 | 1069.838 | 1057.846 |
| 6 | 1066.897 | 1053.548 |
| 7 | 1060.850 | 1051.911 |
|----------+----------+-----------|
| Mean | 1065.25 | 1054.84 |
The improvement is more limited on kano because a longer PCIe
initialization delays EOP in the Late EOP configuration which make it
faster to complete.
CSME team confirms that:
1. End-Of-Post is a blocking command in the sense that BIOS is
requested to wait for the command completion before loading the OS or
second stage bootloader.
2. The BIOS is not required to actively wait for completion of the
command and can perform other operations in the meantime as long as
they do not involve HECI commands.
On Raptor Lake, coreboot does not send any HECI command after
End-Of-Post. FSP-s code review did not reveal any HECI command being
sent as part of the `AFTER_PCI_ENUM', `READY_TO_BOOT' or
`END_OF_FIRMWARE' notifications.
If any HECI send and receive command has been sent the extra code
added in `cse_receive_eop()' should catch it.
According to commit 387ec919d9f7 ("soc/intel/alderlake: Select
SOC_INTEL_CSE_SEND_EOP_LATE"), FSP-silicon can sometimes (on the first
boot after flashing of a Marasov board for instance) request coreboot
to perform a global request out of AFTER_PCI_ENUM notification. Global
request relies on a HECI command. Even though, we tested that it does
not create any issue, `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag should not
be associated to the `SOC_INTEL_CSE_SEND_EOP_EARLY' flag to prevent
potential a global reset command to "conflict" with the EOP command.
BUG=b:276339544
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with and `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post sent soon after FSP-s and EOP message receive at
`BS_PAYLOAD_BOOT'. Verify robustness by injecting a
`GET_BOOT_STATE' HECI command with or without `heci_reset'. The
implementation always successfully completed the EOP before
moving to the payload. As expected, the boot time benefit of the
asynchronous solution was under some injection scenario
undermined by this unexpected HECI command.
Change-Id: Ib09dcf9140eb8a00807a09e2af711021df4b416f
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73619
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
In order for the code to find the correct VBIOS file in CBFS, remap the
revision ID in the RAVEN2_VBIOS_VID_DID case to the one that matches the
CBFS file name. This will make the code work as expected on devices with
the PCI ID RAVEN2_VBIOS_VID_DID and a revision != RAVEN2_VBIOS_REV.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94412dc2e778e7c4f74e475cd49114a00a81b2ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74045
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a new port for the Intel DQ67SW desktop board. It is
microATX-sized with an LGA1155 socket and four DIMM sockets for DDR3
SDRAM.
A list of tested working and non-working features is in the
documentation page.
Change-Id: Ifc703f2d0ad45495e71d3f7799347430f5196791
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:275644832
TEST=emerge-dedede coreboot
BRANCH=firmware-dedede-13606.B
Change-Id: I644f3aa3187e08146d78abb70a568833bc9b9211
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure GPIOs according to schematics(ver. 20230308).
BUG=b:272829190
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id414c9b0d94faffd2d71c348fc7146a6101196e9
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Initial hades GPIO config. Combination of original brya basebaord,
Agah and new arbitrage output for hades design.
Also moved GPIO config to the non baseboard variant model as we did on
rex0.
BUG=b:269371363
TEST=builds
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I2a850240dd7f3ddf137d6a2ebe8a147f8976c16b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72679
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The patch enables addition of core_type member to 'struct cpu_info' for
Alderlake platform.
TEST=Build and verify the code for Gimble
Change-Id: Ia065b98c2013e78328fd38bed9c667792d6d1f4d
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74089
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The patch adds new member 'core_type' to the 'struct apic_path' and
updates core type information.
TEST=Build the code for MTL
Change-Id: I1d34068fd5ef43f8408301bf3effa9febf85f683
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74088
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Refactor map_oprom_vendev_rev as a preparation to also remap the
revision ID in the RAVEN2_VBIOS_VID_DID case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3b81a9464ed49672889fcb767920154fe6efdfcc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Add early configuration of the GPIOs that control the M2 SSD resets.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I81439d193bdd7296d8a8fea83c5c6be2c75adbea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73989
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add option decode for USB-C DDI connection type and remove unnecessary
break after return.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: If38fa667daeb2dd176ecdf33abaec9b56d633a2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This reverts commit 555ceca38a78 ("mb/google/rex: Enable VPU").
Reason: Unable to boot to latest OS image with VPU enabled.
BUG=none
TEST=Boot to OS image 15376 on google/rex
Change-Id: If61282528922304373d492b362056b52995cbcad
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paz Zcharya <pazz@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
The Realtek RTL8111E NIC is currently not defined as a child device,
resulting in the on_board flag not being set to 1. This means that
Linux / udev will call the device enp4s0 rather than eno0, as is
appropriate for on-board ethernet devices.
This patch defines the NIC as a child device of PCIe port 6, so that
it's properly defined as an on-board device.
Change-Id: I2e1b65e4d27852297a739e332c52c15a8c81b858
Signed-off-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74090
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use enum cb_err as return value of fsp_find_range_hob instead of using
the raw -1 and 0 values. Also update the call sites accordingly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6c9f69a886f53868f1ef543c8fa04be95381f53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Since the return value of the fsp_find_range_hob call is only used in
one location, move the call and return value check into the if condition
block to not need the status variable.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4b9e9251368b86382dc4e050cf176db79dbfb230
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
To remove the annoying "ESC [1m" at SimNow console window.
Change-Id: I300aee946f342f41b94288b75b843956de9d3e88
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
To avoid having to calculate the length of a struct separately, rework
the code to give the struct a tag name, so that `sizeof()` can be used
instead. This involves refactoring the `get_emi_eeprom_vpd()` function
to return a struct instead of a union, so callers can no longer access
the EEPROM data as an array of bytes without additional code, but this
array view is only used inside `get_emi_eeprom_vpd()` when reading the
data from EMI.
Change-Id: Id1bc40939631baa131b5f60eadbfe42838294ebe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch avoids the redundant programming of SRAM BAR when
the SRAM PCI device is enabled. Rather read the PCH SRAM Base
Address Register while enabling crashlog feature.
Additionally, this patch relies on PCI enumeration to get the
SRAM BAR rather than hijacking the SPI temporary base address
which might have resulted in problems if SPI is disabled on
some platform with BAR being implemented.
TEST=Able to build and boot google/marasov and crashlog is working.
Change-Id: I8eb256aa63bbf7222f67cd16a160e71cfb89875a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned, and devicetree does not currently support this (it
disables all probed devices when fw_config is unprovisioned).
BUG=b:273791621
TEST=emerge-nissa coreboot
Change-Id: I1a6013e0ad0c430d83bbbad4b92392c8c4815b0d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree according to yavilla's design.
Add Kconfig for TPM I2C bus.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I1b44436a7f93d62764d0451c738ae33976a24a15
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Use die_no_apcb to cause a build error when the APCB or SPD sources are
not found.
TEST=builds with and without matching APCB and SPD sources
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I62dce2c71061bfc5c01e0344b7dc115a47669140
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This sets the location of the skyrim MP2 firmware within the mainboard's
blobs directory, and adds the Kconfig option to the mainboard directory
so that it can be enabled in a saved .config file.
The skyrim MP2 firmware is skyrim specific, so it should not be placed
in the main PSP AMD_BLOBS directory.
We will also only want to enable the MP2 firmware for chromeos builds as
it's not useful for non-chromeos builds.
BUG=b:259554520
TEST=Build MP2 firmware into image, see that it gets loaded
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I04be6f2d0b605d4eca37fd927a70310259dc106c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Instead of using the PSTATE SSDT generated by binaryPI, use the common
AMD code by selecting SOC_AMD_COMMON_BLOCK_ACPI_CPU_POWER_STATE. To
match the SSDT from binaryPI, set ACPI_SSDT_PSD_INDEPENDENT to n. There
are two differences to the binaryPI SSDT: Now coreboot includes the C1
state in the _CST package instead of just having the kernel add this due
to the ACPI_FADT_C1_SUPPORTED bit being set and the address of the
PS_STS_REG P state status MSR is written to the corresponding field of
the _PCT package instead of being 0.
TEST=On Careena the new P and C state ACPI packages are nearly identical
to the ones from the SSDT from binaryPI with the two functional
differences mentioned above.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icdf6bc8f0e0363f185a294ab84edcb51322e7eb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Both the algorithm and the registers involved are described in the
public version of BKDG #55072 Rev 3.09 in chapter 2.5.2.1.7.3.2 _PSS
(Performance Supported States).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9b2c177d9d80c5c205340f3f428186d6b8eb7e98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
