| Age | Commit message (Collapse) | Author |
|---|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
An underscore has crept into the mainboard model option for mc_ehl3 and
mc_ehl4 by mistake. This patch fixes the incorrect entry.
Change-Id: Ie59619877fb6341a5bbfe91c13e7692943480ad0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75040
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I116b1e36f0582956604c3c2508961ffb3de0898a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74947
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
If the ME is disabled with the `me_state` CMOS setting, boot
times are approximately 5 seconds longer:
942:before sending EOP to ME 1,240,773 (5,599)
943:after sending EOP to ME 6,263,951 (5,023,177)
Total Time: 6,167,443
This is because the current code only checks if the ME is
disabled for CSE LITE SKUs. With this patch, boot times are
approximately 5 seconds quicker:
Total Time: 1,143,932
Tested on `starbook/adl` and `starbook/tgl`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I182f30d4fbf43955747c6a7a0b284a43f9c5e4ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Update header files for FSP for Meteor Lake platform to version 3165_81, previous version being 3084_85.
FSPM:
1. Change UPD name from 'GtExtraTurboVoltage' to 'GtAdaptiveVoltage'
2. Change UPD name from 'CoreVoltageAdaptive' to 'CoreAdaptiveVoltage'
3. Change UPD name from 'RingVoltageAdaptive' to 'RingAdaptiveVoltage'
4. Address offset changes
FSPS:
1. Remove deprecated UPD 'PcieDpc'
2. Address offset changes
BUG=b:280005256
TEST=Able to build and boot google/rex to ChromeOS.
Signed-off-by: Kilari Raasi <kilari.raasi@intel.com>
Change-Id: I67939ecf71166fca4f3d2d6cd4622215bebc5718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This fixes an issue where pcie was not power gating and blocked
S0ix entry. Overwrite pcie max non-snoop and snoop latency tolerance
values to 15.73ms as stated in doc #729123 - MTL External Design
Specification.
BUG=none
TEST=Boot google/rex, print/check values.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.corp-partner.google.com>
Change-Id: I9dfb9edbac95d28d50653777466ea172be64f612
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68308
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ibb680bb8f94fb8a2812f420ac38f15684b5c0b4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: I20a66dce1612ab4394c26f9b0943dac14bcdcfc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The Intel SoC Meteor Lake requires a higher pcie max non-snoop and
snoop latency tolerance. Add config to let SoC overwrite the common
code settings if needed.
BUG=none
TEST=Boot google/rex and print/check if able to overwrite values.
Change-Id: Ic2b9a158d219e6c6e7f6e7f0ae0f093c1183b402
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Intel's EHL FSP offers the possibility to select the connected hard
drive type to SATA ports. One has the option to choose between HDD ('0'
- default) and SSD ('1').
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: Idb03aff5b6c5df592b47e2f4abe4fe58ac7151ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74946
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Follow the EC GPIO programming sequence to enable the MXM PCIe slot.
Change-Id: I75d7ac488bb005751e6f674ab9a2fd99baad571b
Signed-off-by: Anand Vaikar <a.vaikar2021@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
All other boards use MAINBOARD_ prefix instead of board name.
Change-Id: I97d9d28963c97e780156d75b39deac069028866a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Processing LD flags is done without most warnings enabled, which is why
this never caused problems.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic9d82c1426a1c1d2f21c8e7560685cf9d7106a88
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75033
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4d34e5c094440dad4a6ab9adc67d3da6b71ac2bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74514
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: If4b7c2b94e0fec84831740336ccdbea0922ffbfe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74513
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name.
Change-Id: I2ae03a3ac548674b8c5e7dfaff47d6c536b452f1
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75013
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I27a610255e5680be1b507d45c6695cf9419ee052
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: I3881c152663a038833d8126d7f24f2a6688426d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74515
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Assigning duty_offset while duty_width==0 has no purpose.
Under intel/common/block, previous assignment for fadt->gpe0_blk
resolves GPE0_STS(0) from xeon_sp/ebg/.../soc_pm.h and also assigns
value matching pmbase + 0x60.
Change-Id: Iaf688d9471ac527ac20307cf16216abdab731a06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74827
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The STA_HIMAX83102_J02 and STA_ILI9882T panel will be used for Starmie,
enable these two panels config for it.
BUG=b:272425116
BRANCH=corsola
TEST=build starmie and check the cbfs include the panels
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I1dd696dd6a84d9606e4b9a2d4884dd70a6df9161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74200
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add STA_ILI9882T panel serializable data to CBFS.
The panel datasheet: ILI9882T_Datasheet_20220428.pdf
BUG=b:275470328
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ia7a37c0659f0959fe7be01aba0f08d63119d139f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
This reverts commit d6e0a90aa0bd574b28b6c9b4b46289bf46a208db.
Reason for revert: Not ready to land, blocked by ancestor CL
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic14e17db4aed2f998878920c66cdc16362920dcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75050
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the CMOS bank I/O base addresses with
PC_CMOS_BASE_PORT_BANK* rather than hard-coding as 0x70, 0x72. The
defaults remain the same.
Change-Id: Ie44e5f5191c66f44e2df8ea0ff58a860be88bfcf
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74903
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CMOS defaults greater than 128 bytes long will extend to bank 1.
Change-Id: I9ee8364d01dd8520be101de3f83d2302d50c7283
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
FSP-M is normally memmapped and then decompressed. The SPI DMA
controller can actually read faster than mmap. So by reading the
contents into a buffer and then decompressing we reduce boot time.
It is interesting that FSP-M takes an additional 8ms to execute. I
suspect since we call it 50ms earlier it's having to wait for one of
its dependencies.
BUG=b:179699789
TEST=Boot guybrush and see 30ms reduction in boot time
| 970 - loading FSP-M | 0.316 | 0.997 Δ( 0.68, 0.05%) |
| 17 - starting LZ4 decompress (ignore for x86) | 0.026 | 13.874 Δ( 13.85, 0.96%) |
| 18 - finished LZ4 decompress (ignore for x86) | 64.361 | 0.337 Δ(-64.02, -4.43%) |
| 2 - before RAM initialization | 0.534 | 0.529 Δ( -0.01, -0.00%) |
| 950 - calling FspMemoryInit | 1.455 | 1.132 Δ( -0.32, -0.02%) |
| 951 - returning from FspMemoryInit | 207.695 | 216.537 Δ( 8.84, 0.61%) |
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I850b1576501753a355e7b23745e04802a0560387
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Librem Mini v1/v2 has an automatic power-on setting provided by the EC
in BRAM bank 1. Use this bank as the high bank of CMOS memory so that
setting can be described in cmos.layout.
Change-Id: Icb87bc521f71aa4350c8f5a64fc2cbe7a7a8c808
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Beware that there's no XHCI2 controller and the USB4 controller device
pointers were added right after the xhci_0 and xhci_1 controller device
pointers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14725d4b546ffcca42e21bbe7756babaaff8fea3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74658
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Introduce acpigen_write_BBN to generate the ACPI method object that
returns the base bus number for a PCI(e) host bridge. When called, the
base_bus_number argument must be the first PCI bus number that got
assigned to the corresponding host bridge.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib67bf42b9c77c262d8a02d8f28ac5cb8482136b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
Add STA_HIMAX83102_J02 panel serializable data to CBFS.
The panel datasheet: HX83102-J02_Datasheet_v03.pdf.
BUG=b:272425116
BRANCH=corsola
TEST=build and check the CBFS include the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I382bdc89e5a217fd1c28e677938f454dc09725cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Add FW_CONFIG item for FP sensor init and conditionally init
the GPIOs based on whether we're using a SPI or UART FP sensor.
BUG=b:276939271
TEST=builds
Change-Id: I9815bd17df1d15f73529beb15d08cde1ef90efad
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG item for eMMC/NVMe support and address the init
of the lanes based on said config.
BUG=b:278877257
TEST=builds
Change-Id: Id6452f497cf78549b7d6126f1b55cd6d45b403c3
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74957
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Mark Hasemeyer <markhas@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For early Sign of Life to work, we may need certain pin configurations
very early in boot (e.g. HDMI). This may happen before romstage GPIOs
are configured, and bootblock is not suitable for field upgrading
existing devices. Add a separate GPIO table that can be configured
when early graphics is invoked.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on HDMI enabled variants
Change-Id: I7b3ce96a4166451e72aa70b3086eff3fb8b082b7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Allow different gma-mainboards configs for different baseboards
as they support varying display interfaces. Set Brya to eDP only
and Brask to HDMI only.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on both brya and brask varaints
Change-Id: Iaf3f35b009d53e50723e4aa82c0f4932783f9bb9
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Denote the correct value of ACPI _PLD for USB ports.
The horizontal position of port C0 is incorrectly labelled.
+----------------+
| |
| Screen |
| |
+----------------+
C0 | | A0
| | C1
| |
+----------------+
BUG=b:216490477
TEST=emerg-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id9ed435ca0af131e3bb4538701fc97d78146899f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74366
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add _PLD support to GFX device so that each display output can store
its physical location of connection point. This is to be used primarily
for describing DP on USB-C ports in the future patches.
The upstream Linux kernel now has a feature to compare _PLD of Type C
connectors and DP connectors to link them together.
https://cgit.freedesktop.org/drm/drm-misc/commit/?id=c5c51b2420625faa1f0e363f21dba1de53806ff7
This feature allows us to tell which display output is used by which
USB-C port.
So, for the future boards, we want to add _PLD for each DP connector
matching with the corresponding USB-C port.
BUG=b:277629750
TEST=emerge-${BOARD} coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: I393207746a9e82c1fd7622ab3661d7b1232cb62f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch adds some of the variety of configuration options exported
by the Pericom Inc. PI7C9X2G608GP PCIe switch over its SMBus interface.
Currently implemented options are only used to adjust the switch
upstream port amplitude and de-emphasis levels in millivolts. Only
values specified in the switch datasheet (in tables 6-6 and 6-8) are
allowed.
Example of a devicetree.cb entry:
chip drivers/i2c/pi608gp
register "gen2_3p5_enable" = "true"
register "gen2_3p5_amp" = "AMP_LVL_MV(425)"
register "gen2_3p5_deemph" = \
"DEEMPH_LVL_MV(37, 5)"
device i2c 0x6f on
ops pi608gp_ops
end
end
Link to the datasheet:
https://web.archive.org/web/20210225074853/https://www.diodes.com/assets/Datasheets/PI7C9X2G608GP.pdf
BUG=none
TEST=Create devicetree.cb and Kconfig entries for this driver
in a mainboard containing the switch and verify, that the values read
out from the switch config space match the values programmed over the
SMBus.
Change-Id: Id191c4e97b99da58efd3ba38bf8cca3603ece4d5
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Update eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 10 cycles of cold boot successfully
Change-Id: I46e2f9df0e82e66fa3ae32aa87b4bcf30d5737ab
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree to support G7500 touchscreen.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and check touchscreen function
Change-Id: I3b63b1bb45275ad7eef8799dcff27f264739c258
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Id5b0fa96ca8d86ddf20d808f5107a43ad2d0a1e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Return 0xf from PCI0 _STA method so that bit 2 is set which indicates
that the device should be shown in the user interface. This ports commit
c259d7192806 ("soc/amd/stoney/acpi: Unhide PCI0 root device from OS")
back from Stoneyridge.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5e724292431be7f7c2a0b6678b426831e3c19154
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74990
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Return 0xf from PCI0 _STA method so that bit 2 is set which indicates
that the device should be shown in the user interface. This ports commit
c259d7192806 ("soc/amd/stoney/acpi: Unhide PCI0 root device from OS")
forward from Stoneyridge to the newer AMD SoCs.
TEST=On Mandolin the PCI Express Root Complex now shows up in the device
manager on Windows 10 and when switching the view to 'devices by
connection', all PCI(e) devices are shown below it.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4155556dc5df8f163fe06aa6719fadbb2684cc19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74949
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures that the PRERAM_CBMEM_CONSOLE_SIZE and
CONSOLE_CBMEM_BUFFER_SIZE hold a larger cbmem buffer size to contain
the entire FSP debug serial log.
The existing implementation was not appropriate, where the larger cbmem
size was even applicable for serial AP firmware (w/o FSP debug) image
as well.
This change is necessary to ensure that the FSP debug serial log is
always available, even in cases where the cbmem buffer size is
limited.
BUG=b:280481298
TEST=Able to build and boot google/rex with non-FSP serial AP image
and with FSP serial AP image. Able to see the AP log completely inside
the cbmem.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib35780fd558c8b6d9aa2e17241131ea4a58c2b9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
While Chromebook hardware originally would not have the
capacity to do suspend-to-disk (ACPI S4), the power management
code in EC should react to S4 request as if it was S5 request.
Change-Id: Ida9118919c8149d94f470847d0c4aad9c0b97d3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
No longer needed, this was used with old SMM relocate code.
Change-Id: I7c913e10eb965419c7d2ddede744f8140a5b7976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I7655de5a8fcd5ac5c820938059bbb8b1ad877db7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
To select COMMON_SMM should not imply COMMON_PMBASE, it's
really a depencency. Select them both explicitly for i82801dx.
Change-Id: I387ade9cfd38b6555ed9e37c1b9178a6da2d7260
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I0ada381883aa65d36434486dcce6b2331599e5c3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I47ec05aa87e4e7c02b19817b2f703eca492008e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch makes CSE sync in romstage default enabled unless ramstage
config (SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE) chooses to override it.
TEST=Able to build google/marasov with this change where CSE sync is
performed early inside romstage.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3f5017fbcf917201eaf8233089050bd31c3d1917
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Add DDR DQ map config for screebo
BUG=b:276814951,b:272218757
TEST=emerge-rex coreboot
Change-Id: I993ae4024689b9cedbea247689a760bd83cd0d45
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74961
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add variant makefile to support including the memory folder for Myst.
BUG=b:273383819
TEST=Builds in chromium with blobs
Change-Id: I03b0cd91dd66f357b15522da36f5118867b6b14c
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74964
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the OEM ID from CBI to determine the correct OEM board name.
ID mapping taken from ChromeEC source, branch firmware-fizz-10139.B.
TEST=build/boot multiple fizz variants, check that board name reported
correctly in SMBIOS tables.
Change-Id: I06251974ac73570b911920ed566a175e8e733710
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Override SMBIOS product name with sub-variant name based on board SKU.
TEST=build/boot multiple nami variants, verify SMBIOS product name
reports correctly.
Change-Id: I2125bfb6436469405378f9c983d7cfcb2f85f916
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Only expand these strings in lib/identity.o.
Change-Id: I8732bbeff8cf8a757bf32fdb615b1d0f97584585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adjust a few things so that the sleepstates.asl file is the same for
sb/amd and soc/amd. These adjustments don't have a functional impact.
Change-Id: I0cc9462b326cdc371ffdbf5759d8adc42456ce74
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74960
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit cbc5d3f34b87db779829eabc90c32780a3865a56 ("soc/intel: Don't
report _S1 state when unsupported") added the `ACPI_S1_NOT_SUPPORTED`
option and commit 0eb5974def63a2fc0dce6dfdad62b0b4c6f4b865 ("acpigen:
Add a runtime method to override exposed _Sx sleep states") added a
mechanism to override the enabled sleep states at runtime. However,
these were only hooked up to Intel sleepstates. so the options would
not have any effect on AMD platforms.
Apply the changes from these two commits to AMD sleepstates so that
both options can be used on AMD platforms as well.
Change-Id: I7d5ef2361e36659ac5c6f54b2c236d48713a07c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74959
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Iaf88f34cedd09e2461bb05050392e178ec84d5d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for marasov board. Please refer to Intel doc#723158
for more information.
BUG=b:279117758
BRANCH=firmware-brya-14505.B
TEST=Boot to OS on marasov.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I286e88e5bec240d64e6c801648f6483ad2b0939c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74931
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure the SuperIO and logical devices in the device tree. This
overrides the power-on default state.
UART1 was already enabled, and if ENABLE_EC_UART1 was selected in
Kconfig, the LPC UART1 I/O range was also already enabled.
The RTC/BRAM interface was enabled (and the BRAM1 base was 0x360 by
default), but the LPC I/O range was not opened previously. Now it is
open and BRAM bank 1 is accessible.
Mouse/Keyboard are not wired to anything on this board and are now
disabled.
UART2, SMFI, power channel 1, and power channel 2 were enabled
previously, but their LPC I/O ranges were not opened and they were not
accessible to the OS. Fan control is performed by the EC on this board
so there is no change.
SWUC and power channels 3-5 were disabled by default, no change.
Change-Id: I58a5a427737f4a2caa64326c110eb53ec00b347d
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
variant_board_sku() is missing dependences in order to work correctly
in romstage. Rather than more intrusive rework as its use is limited,
move the FPMCU early GPIO init back to ramstage. We still meet
sufficient power off time to fully power cycle the MCU.
BUG=b:245954151
TEST=Confirmed FPMCU is still functional on Nami and FP tests all pass
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: Ia428ec5aec1a0438e91bc48903bda043046b740e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74695
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The image processing unit/GMM and xDCI are not used on octopus boards;
additionally, enabling xDCI can cause some problems with USB ports in
both booting from the payload and in the OS.
Change-Id: I1ee99b5c45881a4cf3624bf487bc9d83fb3d07a1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The commit a0b199c6b483 ("soc/intel/xeon_sp/spr: Add soc
set_cmos_mrc_cold_boot_flag") introduced a copy-paste issue in two error
messages. The error messages should mention the Intel platform SPR
instead of CPX. Fix that.
Change-Id: I4de61ec2cf9fbd98263a7a7a588938d548148656
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74956
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on wyvern variant, verify headphone output
and microphone functional under Windows using coolstar's SOF drivers.
Change-Id: I421c070eac321c2fc160b8f26868bcb1ec13001e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74815
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several volteer variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I62a96149cec9eeb7b2da8a2337083969a1b0fce0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74816
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on banshee and osiris variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I12614b85f9779cc40d83a9c868cc46b110f26af6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74817
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add all SOF chip drivers to baseboard and use FW_CONFIG to determine
the correct option, to ensure the correct audio config is passed to the
SOF OS drivers.
TEST=build, boot Windows on several dedede variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I9452b11af614d8727aa8dd448e37f7a06faa450d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74818
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Now that we don't need to find a specific resource in the set resources
function any more, there's no need to use hard-coded indices for the
fixed resources. Instead use an index variable that gets incremented
after each fixed resource got added. The index now starts at 0 instead
of at 1, but now the only requirement is that those indices are unique.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ida5f1f001c622da2e31474b62832782f5f303a32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74849
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Since commit 833bb448c521 ("mb/siemens/mc_ehl: Remove spd.bin from
CBFS"), the subdir 'spd' is no longer necessary.
Change-Id: Ibaf44e3181b2167aa83cffcc59835196e4cb5cdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Remove explicit PNP 6e.1 configuration for UART. This had no effect,
the SuperIO is actually on I/O port 2e. Enabling the 8250IO driver is
sufficient to use the UART, the UART device is enabled by default.
Test: Build Mini v2 with and without CONFIG_ENABLE_EC_UART1, boot and
check output on serial.
Change-Id: Idbb39c81cadd633f4718f0682d231dc578d20325
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74362
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the fallback value of the `fn_ctrl_swap` option to 0, which
is disabled.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I76329ec59ba630c987a122bffb8045150facdf08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Drop the custom lpc_set_resources implementation that does some register
access that has no effect and then calls pci_dev_set_resources and use
pci_dev_set_resources for set_resources in amd_lpc_ops instead.
The SPI controller's base address got configured early in boot in the
lpc_set_spibase call and the enable bits got set early in boot in the
lpc_enable_spi_rom call.
TEST=The contents of the SPI_BASE_ADDRESS_REGISTER at the beginning and
at the end of the call stay the same, so it's simply a no-op.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7a5e3e00b2e38eeb3e9dae6d6c83d11ef925ce22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I77471d464dddffc63bb2f005fef3a33c84ff5f5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I813a27e392a842188dc474018f82e10309783260
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I63fb70da3e9ded6c05354f94ee69bc6dd04e58f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The memory map granularity for those devices is 4kByte.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8806128bdce8988f5cd7c8fa8a342fdb01eb7f42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Since the 16MByte of memory-mapped SPI flash region right below the 4GB
boundary is both a fixed region and isn't decoded on a device below the
LPC device, but assumed to be decoded by the LPC device itself, it
shouldn't be reported as a subtractive resource, but as an MMIO resource
instead.
TEST=On mandolin the 16MByte MMIO-mapped SPI flash now show up as a
reserved region in the e820 memory map which wasn't the case before:
13. 00000000ff000000-00000000ffffffff: RESERVED
The Linux kernel doesn't show any new or possibly related errors.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ib52df2b2d79a1e6213c3499984a5a1e0e25c058a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Tuning i2c frequency ,timing ,Waveform meet to SPEC
i2c frequency :
I2C0=>399.8khz / Setup Time:1765ns / Hold Time:82.35ns.
I2C1=>390.4khz / Setup Time:1.788us / Hold Time:70.58ns.
I2C3=>308.7khz / Setup Time:1.482us / Hold Time:0.4us.
I2C5=>390.8khz / Setup Time:1.218us / Hold Time:0.405us.
BUG=b:275061994
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot,
EE check OK with test FW and TP function is normal.
Change-Id: I5b77cd3fd3ff00804f1b8dd5828dc831a9732566
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74880
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
The patch orders MTL RVP board Kconfigs alphabetically.
TEST=Build the code for mtlrvp
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ib8557aab2848a384fba5203e5f3d62407b2566ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
We have largely dropped from filling in mainboard_ops.name
as unnecessary. A common place should be decided where or if
this information is added in the console log.
Change-Id: I917222922560c6273b4be91cd7d99ce2ff8e4231
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several hatch variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: Ie791fa873fc7bbab84644f5ea5743bdcdc124908
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Add a new chip driver for boards which use SOF (Sound Open Firmware)
OS drivers, which will be attached to the HDAS device and generate
entries in an ACPI _DSD table for the OS driver to use. This will allow
the OS drivers to easily determine the correct topology for the speaker
and jack amplifiers and correct microphone configuration.
TEST=tested with rest of patch train
Change-Id: Ie0431b2002287f35245cbf959828e931d7f375b2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Iadc32f4dbf8bd48d8666a213d7b5f3ba42175a90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The image processing unit (Iunit) and SoC UARTS are not used on any
reef boards.
Change-Id: Iacdf93b4952cbc63fc465f07d440463106527b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
It's not particularly useful to end users, and shows up as an unknown
PCI device under Windows Device Manager.
TEST=build reef, boot Windows, verify unknown PCI device no longer
present in Device Manager.
Change-Id: Ie8ec46e2e07b6635bfe9766812ce08b866c71d66
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add rules to inject the variant specific SPD binaries into APCB.
BUG=b:273383819
TEST=Build Myst BIOS image. Currently no APCB is present. So no SPD is
injected into APCB.
Change-Id: Ic511cdc4fe0989c9abc0cd0531cc0cae40f8dc34
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74746
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Generate the RAM Strap IDs based on the initial memory configuration.
BUG=b:272746814
TEST=Build Myst BIOS image.
Change-Id: I8a4fe9a41f101ac10391756f1b815220c8b98612
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Since disabling C1E could improve acoustic noise for RPL, add judgement
in SOC code to disable C1E on RPL CPUs and enabling it on ADL CPUs .
BUG=b:278654939
TEST:emerge-brya coreboot
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Ic2d2d5d6075de25141c1d08ec18838731c63a342
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change-Id: I6b53536a3d673350fa1b46891da2766b0bc149e8
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
At present the problem has only been reported with Alder Lake and
Raptor Lake FSP where MultiPhaseSiInit API is unable to return any ERROR
status. Hence, this patch ensures to select applicable W/A config to
read FSP return status from the FSP Reset HOB.
BUG=b:278665768
TEST=Able to select FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN for ADL/RPL SoC
code and call into this API to know the return status from
MultiPhaseSiInit FSP API.
Without this patch:
IshInit() Start
IshDisable() Start
IshPerformGlobalReset()
....
....
FSP returning control to Bootloader with reset required return
status 40000003
FspMultiPhaseSiInit Index-1 returned 0 <-- after control returns
into coreboot, the `status` from the FSP API is reset to `0`
instead 0x40000003. Hence, coreboot avoid hitting the reset.
With this patch:
IshInit() Start
IshDisable() Start
IshPerformGlobalReset()
....
....
FSP returning control to Bootloader with reset required return
status 40000003
FSP: handling reset type 40000003 <-- coreboot is able to understand
the reset request in proper.
GLOBAL RESET!
global_reset() called!
HECI: Global Reset(Type:1) Command
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I18a918cca7e19e03ed6020c55c86c64a94212963
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74785
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch calls into fsp_get_pch_reset_status() to get the
MultiPhaseSiInit API return status if
FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN is enabled.
Ideally FSP API should be able to return the status (both success and
error code) upon exiting the FSP API but unfortunately there are some
scenarios in ADL/RPL FSP where MultiPhaseSiInit API is unable to return
any ERROR status. Hence, this function can be considered as an
additional hook to read the FSP reset status by reading the dedicated
HOB without relying on the FSP API exit status code.
Any SoC platform that selects the FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN
config will call into this newly added API to get the FSP return status
from MultiPhaseSiInit.
BUG=b:278665768
TEST=Able to select FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN for ADL/RPL SoC
code and call into this API to know the return status from
MultiPhaseSiInit FSP API.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I749c9986e17e4cbab333b29425c9a4a4ba4128fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74784
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
|
|
This patch creates a function to read the FSP API Reset Status. This
function relies on the FSP Scheduled Reset HOB which holds the reset
type (warm/cold/shutdown) information along with any platform specific
reset need (like global reset).
Ideally FSP API should be able to return the status (both success and
error code) upon exiting the FSP API but unfortunately there are some
scenarios in ADL/RPL FSP where MultiPhaseSiInit API is unable to return
any ERROR status. Hence, this function provides an additional hook to
read the FSP reset status by reading the dedicated HOB without relying
on the FSP API exit status code.
Additionally, create FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN config option
to handle broken FSP API return status issue.
Any SoC platform that selects the `FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN`
config will call into this newly added API to get the FSP return status
from MultiPhaseSiInit.
BUG=b:278665768
TEST=Able to select FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN for ADL/RPL SoC
code and call into this API to know the return status from
MultiPhaseSiInit FSP API.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ief5d79736cc11a0a31ca2889128285795f8b5aae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
There is no platform-level implementation for USB port power management
in various sleepstates. This mainboard never evaluates the set GNVS
variables S3U0, S3U1, S5U0 and S5U1 in ASL or in its SMI handlers.
Change-Id: Ic7af2d608d95c6691f31ef1b8af72f96da20787c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There is no platform-level implementation for USB port power management
in various sleepstates. The mainboards changed here never evaluate the
set GNVS variables S3U0, S3U1, S5U0 and S5U1 in ASL or in their SMI
handlers.
Change-Id: Ia1bc5969804a7346caac4ae93336efd9f0240c87
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
|
|
Change-Id: I5a75a7230fd78c0a9926adc491059f55647cc9a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: I634af65cd41e0d70e673d550ed8063abc6eea6d4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add data.vbt files for all variants supported by current volteer
recovery image. Several boards use the same VBT, so place the "common"
VBT under the baseboard directory and set it as the default.
For variants with a unique VBT, override the default and use the file in
their respective variant directory. Select INTEL_GMA_HAVE_VBT for all
variants which have a VBT file.
TEST=build/boot various volteer variants
Change-Id: I728ab81938c78f600ff8931a8073d1f7de152c09
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74852
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These were hidden because no Windows drivers existed, but now that
they do, the ACPI devices need to be visible in order for the
drivers to properly attach.
TEST=build google/banshee, boot Windows, verify Windows drivers
correctly attach to PCM/IOM devices.
Change-Id: Idbbaee29bffb49059d8450abd09e0c3f7b490fae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74850
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
These were hidden because no Windows drivers existed, but now that
they do, the ACPI devices need to be visible in order for the
drivers to properly attach.
TEST=build google/drobit, boot Windows, verify Windows drivers
correctly attach to PCM/IOM devices.
Change-Id: I1520a71e318674baa234fc6a2126d1d17933d983
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
