| Age | Commit message (Collapse) | Author |
|---|
|
With the latest hardware revision, the two GPIOs GPD11 and GPP_C8 are no
longer used.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: Ia06f93aee4eccb0e4230f0c3ef53922d42701f21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74201
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Ioapic information in the devicetree was only used to set up mptables
but this generic driver was removed (ca5a793 drivers/generic/ioapic:
Drop poor implementation).
This removes the unused remainders from mainboard devicetrees.
Remove ioapic setup from sconfig.
Change-Id: Ib3fef0bf923ab3f02f3aeed2e55cf662a3dc3a1b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Now the CPU topology is filled in struct device during mp_init.
Change-Id: I7322b43f5b95dda5fbe81e7427f5269c9d6f8755
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
From request, all type C port limit to to Gen1 5GHz.
So enable UPD usb3_port_force_gen1 for Markarth.
BUG=b:273841155
BRANCH=skyrim
TEST=Build, verify the setting will be applied on Markarth.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I9314b67a82ad2993c87f0110db5ec927caaa772b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74087
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add GPU power sequencing changes for the Hades baseboard and variant.
Some signals were added, moved or inverted.
Based on implementation from Agah.
Moved signals:
GPIO_1V8_PWR_EN GPP_E11
GPIO_NV33_PWR_EN GPP_E2
GPIO_NV33_PG GPP_E1
New signals:
GPIO_NV12_PWR_EN GPP_D0
GPIO_NV12_PG GPP_D1
Inverted signals:
GPIO_FBVDD_PWR_EN GPP_A19
ifdef's will be dropped once the Agah variant is retired.
BUG=b:269371363
TEST=builds and verified on Agah that DGPU is still detectable (lspci)
Change-Id: I0b8efe7a34102cf61d4f784103c4a4f9337213f7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
mainboard_vbt_filename() used to assume that it is called after a call
to get_blc_pwm_freq_value() with a valid parameter, but currently it
is the first call of get_blc_pwm_freq_value(NULL), and will return 0,
so "data_led.vbt" is always returned, regardless of the actual type of
the panel.
Combined with the previous commit, in this commit
mainboard_vbt_filename() will explicitly read EDID string via
gm45_get_lvds_edid_str() and use this string to call
get_blc_pwm_freq_value().
Resolves: https://ticket.coreboot.org/issues/475
Tested on my x200s with LTD121EQ3B (LED), and x200 with LTD121EWVB
(CCFL).
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I2e080b29321b6989d1f26b6c67876b3d703042f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74181
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This patch updates the MTLRVP debug flash layout to optimize WP_RO to 4MB.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Increase to 7.5MB.
RW_LEGACY: Introduce with 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 2MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot intel/mtlrvp with FSP release and debug image.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie635e3cce1c3fd771e6a17e4b3c1bd700f4729bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the Rex debug flash layout to optimize WP_RO to 4MB.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Increase to 7.5MB.
RW_LEGACY: Introduce with 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 2MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot google/rex with FSP release and debug image.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4ab69eb24937d58c8bc5d3c0a6e5cb70b843a1ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the MTLRVP flash layout to optimize WP_RO to 4MB.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Reduce to 7MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 3MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot intel/mtlrvp with FSP release and debug image.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibd1ea7a3a2cd21928b8e33473c7bdddfad17c636
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the Rex flash layout to optimize WP_RO to 4MB.
The idea is to create more space inside FW_RW_A/B to accommodate
multiple blobs to boot google/rex with different Intel MTL SoC stepping.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Reduce to 7MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 3MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot google/rex with FSP release and debug image.
Change-Id: Iccf83b7bb66d0d5503e0ff9e9a819051296c6724
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74229
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sends the CSE EOP command asynchronous implementation early
as part of `soc_init_pre_device`.
Without this patch the duration between asynchronous CSE EOP send and
receive commands is not ample whichcauses idle delay while waiting
for EOP response.
The goal of the CSE async implementation is to avoid idle delay while
capturing the response from CSE EOP cmd.
This patch helps to create ample duration between CSE EOP command
being sent and response being captured.
TEST=Able to boot google/marasov EVT sku to ChromeOS and observed
~30ms of boot time savings (across warm and cold reset scenarios).
Without this patch:
963:returning from FspMultiPhaseSiInit 907,326 (97,293)
...
...
115:finished elog init 967,343 (2,581)
942:before sending EOP to ME 967,821 (478)
…
16:finished LZMA decompress (ignore for x86) 1,017,937 (12,135)
943:after sending EOP to ME 1,067,799 (49,861)
…
…
1101:jumping to kernel 1,144,587 (13,734)
Total Time: 1,144,549
With this patch:
963:returning from FspMultiPhaseSiInit 918,291 (97,320)
942:before sending EOP to ME 918,522 (230)
...
...
16:finished LZMA decompress (ignore for x86) 1,029,476 (12,483)
943:after sending EOP to ME 1,033,456 (3,980)
...
...
1101:jumping to kernel 1,111,410 (14,007)
Total Time: 1,111,375
Change-Id: Idaf45ef28747bebc02347f0faa77cc858a4a8ef1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This change enables PCIe x1 slot. In addition, it turns off 3.3v and
12v power and assert PERST# when suspend and turn on the power and
deassert the PERST# when resume for the x1 slot.
NOTE: Kconfig flag and required GPIO pins are already configured.
- /soc/intel/meteorlake/Kconfig
select SOC_INTEL_COMMON_BLOCK_PCIE_RTD3
- gpio.c:
/* GPP_A18: X1_PCIE_SLOT3_PWR_EN */
PAD_CFG_GPO(GPP_A18, 1, DEEP),
/* GPP_A19: X1_DT_PCIE_RST_N */
/* SRCCLKREQ: GPP_C12: SRCCLKREQ3_GEN4_X1_DT_SLOT3_N */
PAD_CFG_NF(GPP_C12, NONE, DEEP, NF1),
BUG=b:224325352
BRANCH=None
TEST=Insert a SD card or NIC AIC on PCIe x1 slot and the AIC should
be detected and enabled at boot. For S0ix, run
'suspend_stress_test -c 1'. The RP6 should not cause any suspend and
resume issue.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Id2e92acf754569a22ea76a68c91aafce0075a742
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73054
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIe bridges need to provide the LTR (latency tolerance reporting)
maximum snoop/non-snoop values so that they are inherited by downstream
PCIe devices which support and enable LTR. Without this, downstream
devices cannot have LTR enabled, which is a requirement for supporting
PCIe L1 substates. Enabling L1ss without LTR has unpredictable behavior,
including some devices refusing to enter L1 low power modes at all.
Program the max snoop/non-snoop latency values for all PCIe bridges
using the same value used by AGESA/FSP, 1.049ms.
BUG=b:265890321
TEST=build/boot google/skyrim (multiple variants, NVMe drives), ensure
LTR is enabled, latency values are correctly set, and that device
power draw at idle is in the expected range (<25 mW).
Change-Id: Icf188e69cf5676be870873c56d175423d16704b4
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74288
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Now that power sequencing has been implemented, switch from using ACPI
"probed" flag to "detect" flag for all i2c touchscreens. This removes
non-present devices from the SSDT and relieves the OS of the burden of
probing.
TEST=build/boot Windows/linux on drallion, verify touchscreen functional
in OS, dump ACPI and verify only i2c devices actually present on the
board have entries in the SSDT.
Change-Id: I3b91a628cd4a9edb5d5a7521529f39b75935e1d0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Ensure the GPIOs themselves are configured as level triggered, as well
as the devicetree entiures. I2C-HID spec requires LEVEL trigger, and the
drivers (both Linux and Windows) work better with LEVEL vs EDGE trigger.
TEST=tested with rest of patch train
Change-Id: I4fba55c938f401876798c2b32c5922523f32180f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
For touchscreens on sarien, drive the enable GPIO high starting in
romstage while holding in reset, then disable the reset GPIO in
ramstage. This will allow coreboot to detect the presence of i2c
touchscreens during ACPI SSDT generation (implemented in a subsequent
commit).
BUG=b:121309055
TEST=tested with rest of patch train
Change-Id: I3ce7bfc0fa4c03c0bb96bebaa3c3d256f886ecc4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add method variant_romstage_gpio_table() with empty implementation to
be used in a subsequent commit for touchscreen power sequencing.
Call method in romstage to program any GPIOs that may need to be set.
TEST=tested with rest of patch train
Change-Id: I11b72a10a4a105385fbcf1d795c020708a7a90d9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Without gpio.c compiled in, SMMSTORE will fail to initialize and hang.
Add a conditional inclusion so gpio.c is compiled in SMM when SMMSTORE
is selected.
TEST=build/boot google/banshee with SMMSTORE support enabled
Change-Id: If049cba98f13f060807058029306dcad2ada2d49
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Stylus reset GPIO needs to be held low in romstage, released
in ramstage for runtime i2c detection to pick it up.
TEST=build/boot AKALI360 variant, verify stylus detected in cbmem,
functional in OS.
Change-Id: I2e7f2a28f6b3a71b0c8fc367168cffbe3f064663
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Deselect the 'fixed resolution at boot' and 'eFP attached' options via
the Windows BMP tool. Fixes HDMI audio output under Windows 10/11.
TEST=build/boot Win 11 on Fizz, verify HDMI audio now functional.
Change-Id: Iecede735bc1266af837e791e6c024aec2f9a8a80
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74235
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
At this moment, only GBB flags are moved from PCR-0 to PCR-1 when
vboot-compatibility is not enabled.
Change-Id: Ib3a192d902072f6f8d415c2952a36522b5bf09f9
Ticket: https://ticket.coreboot.org/issues/424
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Intel ADL-P USB Type-C ports are not compatible with Parade PS8815
retimer on USB U1/U2 transition. The usb_lpm_incapable config is
used to disable USB U1/U2 transition for these Type-C ports.
BUG=b:277149723
BRANCH=firmware-brya-14505.B
TEST=Plug in device and check LPM sysfs nodes are disabled
localhost ~ # cat /sys/bus/usb/devices/2-3/power/usb3_hardware_lpm_u1
disabled
localhost ~ # cat /sys/bus/usb/devices/2-3/power/usb3_hardware_lpm_u2
disabled
Change-Id: I618cd09f45ede0a76cf46b3e467ba87775dd5d9d
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ron Lee <ron.lee@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set NOR pin drive to 8mA to comply with HW requirement.
This implementation is according to chapter 5.8 and 5.19 in MT8188
Functional Specification.
BUG=b:270911452
TEST=boot with following logs
[DEBUG] mtk_snfc_init: got pin drive: 0x3
[DEBUG] mtk_snfc_init: got pin drive: 0x3
[DEBUG] mtk_snfc_init: got pin drive: 0x3
[DEBUG] mtk_snfc_init: got pin drive: 0x3
Change-Id: If8344449f5b34cefcaaee6936e94f7f669c7148b
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74064
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add GPIO driving functions to adjust pin driving.
This implementation is according to chapter 5.2 in MT8188 Functional
Specification.
BUG=b:270911452
TEST=build pass
Change-Id: I87cb8dc00c90fd5b3c0b8bdf5acb92b6f7393a73
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74063
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move GPIO driving-related functions to common for code reuse.
BUG=b:270911452
TEST=build pass
Change-Id: I234a2b7ef5075313144a930332bed10ffec00c6c
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74068
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create a new GPIO driving info table that contains only the pins used
in the bootblock. The GPIO driving info table is downsized from 1480
bytes to 24 bytes.
BUG=b:270911452
TEST=build pass
Change-Id: I24775ba93cd74ae401747c2f5a26bbf1c8f6ac0a
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74062
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Original lastbus configuration consumes constant memory size by
allocating 16 and 8 members arrays and the utilization is bad. Refactor
the lastbus structs to save memory usage.
BRANCH=none
BUG=none
TEST=bootblock.raw.bin size is reduced from 60328 bytes to 59048 bytes.
Change-Id: I07ff9ff7c75f03219e1792b92b62814293ef43fe
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74061
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Geralt uses Samsung panel, and Mutto is responsible for bonding the
panel and touch, so rename the panel description.
Add power-on sequence for Samsung ATNA33XC20 panel.
EDID Info:
header: 00 ff ff ff ff ff ff 00
serial number: 4c 83 62 41 00 00 00 00 28 1e
version: 01 04
basic params: b5 1d 11 78 02
chroma info: 0c f1 ae 52 3c b9 23 0c 50 54
established: 00 00 00
standard: 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
descriptor 1: 35 36 80 a0 70 38 20 40 30 20 88 00 26 a5 10 00 00 1b
descriptor 2: 35 36 80 a0 70 38 20 40 30 20 88 00 26 a5 10 00 00 1b
descriptor 3: 00 00 00 0f 00 d1 09 3c d1 09 3c 28 80 00 00 00 00 00
descriptor 4: 00 00 00 fe 00 41 54 4e 41 33 33 58 43 32 30 2d 30 20
extensions: 01
checksum: 6f
BUG=b:276097739
TEST=test firmware display pass.
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Change-Id: Ibd2d05c7eef1360ca954316f2e76b21ed1f85be8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74115
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: jason-ch chen <Jason-ch.Chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust build configs to build Myst for chromeOS.
BUG=b:270618097
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: If4b6917fe024067409bfbb3d2691c37759b5cace
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=b:271788117
TEST=build FW and system power on.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I411c91e1e70285afbf31750a56a039d60bbe093f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
|
|
Declare CrOS GPIOs for Myst, add relevant defines needed by chromeOS for
additional control GPIOs.
BUG=b:270616013
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Ie876883d6ee2e3bc6324c038cefee12d99702dc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74096
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initial GPIO configuration for Myst.
BUG=b:270596581
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Ia019704c7b027f14d46281e0de0ffdbc4906a20b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74095
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add configuration stubs for GPIOs to be implemented later.
BUG=b:270596581
TEST=builds
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I3228f857da7c8c76cf32faf4a23418aedaf40875
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74094
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Myst is a new Google mainboard with an AMD Phoenix SOC.
BUG=b:270596106
TEST=util/abuild/abuild -t GOOGLE_MYST --clean
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Id7d731ce4d6cb6d4e9041f46eb5a799865bb0b9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74093
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
This to fix following error using Clang-16.0.0:
/cb-build/coreboot-toolchain.0/clang/LENOVO_W500/mainboard/lenovo/t400/static.c:135:22: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.backlight_enable = 0x01,
^~~~
/cb-build/coreboot-toolchain.0/clang/LENOVO_W500/mainboard/lenovo/t400/static.c:136:23: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.dock_event_enable = 0x01,
^~~~
Change-Id: Icd35224877fee355e1bbb8a8e838cb047604babb
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This to fix following error using Clang-16.0.0:
/cb-build/coreboot-toolchain.0/clang/APPLE_IMAC52/mainboard/apple/macbook21/static.c:66:19: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.c4onc3_enable = 1,
^
/cb-build/coreboot-toolchain.0/clang/APPLE_IMAC52/mainboard/apple/macbook21/static.c:75:32: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.p_cnt_throttling_supported = 1,
^
Change-Id: I691b51a97b359655c406bff28ee6562636d11015
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This to fix following error using Clang-16.0.0:
CC romstage/mainboard/emulation/qemu-i440fx/static.o
build/mainboard/emulation/qemu-i440fx/static.c:31:17: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.ide0_enable = 1,
^
build/mainboard/emulation/qemu-i440fx/static.c:32:17: error: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
.ide1_enable = 1,
^
Change-Id: I36cc19bc2908119fe940941e108ee217a7b26f50
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Currently coreboot presents the BSP core first, then efficient cores and
Performance cores as indicated below:
```
/sys/devices/system/cpu/cpu0/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu4/topology/thread_siblings_list:4
/sys/devices/system/cpu/cpu5/topology/thread_siblings_list:5
/sys/devices/system/cpu/cpu6/topology/thread_siblings_list:6
/sys/devices/system/cpu/cpu7/topology/thread_siblings_list:7
/sys/devices/system/cpu/cpu1/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu2/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu3/topology/thread_siblings_list:2-3
```
Existing code presents mix of different cores to OS and causes CPU load
balancing and power/performance impact. So, the patch fixes this
disorder by ordering the Performance cores first, compute die efficient
cores next, and finally SOC efficient cores if they are present. This
is done to run the media applications in a power efficient manner,
please refer the ChromeOS patches for details:
https://chromium-review.googlesource.com/c/chromiumos/platform2/+/3963893
BUG=b:262886449
TEST=Verified the code on Rex system
After the fix:
```
/sys/devices/system/cpu/cpu0/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu1/topology/thread_siblings_list:0-1
/sys/devices/system/cpu/cpu2/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu3/topology/thread_siblings_list:2-3
/sys/devices/system/cpu/cpu4/topology/thread_siblings_list:4
/sys/devices/system/cpu/cpu5/topology/thread_siblings_list:5
/sys/devices/system/cpu/cpu6/topology/thread_siblings_list:6
/sys/devices/system/cpu/cpu7/topology/thread_siblings_list:7
```
Change-Id: I21487a5eb0439ea0cb5976787d1769ee94777469
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
Set the `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag to request End-Of-Post
right after PCI enumeration and handle the command response at
`BS_PAYLOAD_BOOT'.
With these settings we have observed a boot time reduction of about 20
to 30 ms on brya0.
BUG=b:268546941
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post after PCI initialization and EOP message received at
`BS_PAYLOAD_BOOT'.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Ib850330fbb9e84839eb1093db054332cbcb59b41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74215
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
coreboot supports three instances of sending EOP:
1. At CSE `.final' device operation
2. Early as with Alder Lake in chip_operations.init if
`SOC_INTEL_CSE_SEND_EOP_EARLY' is selected
3. At BS_PAYLOAD_BOOT as designed for Meteor Lake if
`SOC_INTEL_CSE_SEND_EOP_LATE' is selected
Currently, Alder Lake uses #3 as it results in better and more stable
boot time. However, what would deliver even better result is to not
actively wait for CSE completion.
This patch introduces a new `SOC_INTEL_CSE_SEND_EOP_ASYNC' Kconfig
which split the action of sending EOP request and receiving EOP
completion response from the CSE.
This patch used in conjunction with #1 can significantly
improves the overall boot time on a Raptor Lake design. For example
`SOC_INTEL_CSE_SEND_EOP_ASYNC' on a skolas board can deliver up to 36
ms boot time improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 1 | 1020.052 | 971.272 |
| 2 | 1015.911 | 971.821 |
| 3 | 1038.415 | 1021.841 |
| 4 | 1020.657 | 993.751 |
| 5 | 1065.128 | 1020.951 |
| 6 | 1037.859 | 1023.326 |
| 7 | 1042.010 | 984.412 |
|----------+----------+-----------|
| Mean | 1034.29 | 998.20 |
| Variance | 4.76 % | 5.21 % |
The improvement is not stable but comparing coreboot and FSP
performance timestamps demonstrate that the slowness is caused by a
lower memory frequency (SaGv point) at early boot which is not an
issue addressed by this patch.
We also observe some improvement on an Alder Lake design. For example,
the same configuration on a kano board can deliver up to 10 ms boot time
improvement as illustrated below.
| # | Late EOP | Async EOP |
|----------+----------+-----------|
| 0 | 1067.719 | 1050.106 |
| 1 | 1058.263 | 1056.836 |
| 2 | 1064.091 | 1056.709 |
| 3 | 1068.614 | 1055.042 |
| 4 | 1065.749 | 1056.732 |
| 5 | 1069.838 | 1057.846 |
| 6 | 1066.897 | 1053.548 |
| 7 | 1060.850 | 1051.911 |
|----------+----------+-----------|
| Mean | 1065.25 | 1054.84 |
The improvement is more limited on kano because a longer PCIe
initialization delays EOP in the Late EOP configuration which make it
faster to complete.
CSME team confirms that:
1. End-Of-Post is a blocking command in the sense that BIOS is
requested to wait for the command completion before loading the OS or
second stage bootloader.
2. The BIOS is not required to actively wait for completion of the
command and can perform other operations in the meantime as long as
they do not involve HECI commands.
On Raptor Lake, coreboot does not send any HECI command after
End-Of-Post. FSP-s code review did not reveal any HECI command being
sent as part of the `AFTER_PCI_ENUM', `READY_TO_BOOT' or
`END_OF_FIRMWARE' notifications.
If any HECI send and receive command has been sent the extra code
added in `cse_receive_eop()' should catch it.
According to commit 387ec919d9f7 ("soc/intel/alderlake: Select
SOC_INTEL_CSE_SEND_EOP_LATE"), FSP-silicon can sometimes (on the first
boot after flashing of a Marasov board for instance) request coreboot
to perform a global request out of AFTER_PCI_ENUM notification. Global
request relies on a HECI command. Even though, we tested that it does
not create any issue, `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag should not
be associated to the `SOC_INTEL_CSE_SEND_EOP_EARLY' flag to prevent
potential a global reset command to "conflict" with the EOP command.
This patch also introduces a new code logic to detect if CSE is in the
right state to handle the EOP command. Otherwise, it uses the
prescribed method to make the CSE function disable. The typical
scenario is the ChromeOS recovery boot where CSE stays in RO partition
and therefore EOP command should be avoided.
[DEBUG] BS: BS_PAYLOAD_LOAD exit times (exec / console): 0 / 14 ms
[INFO ] HECI: coreboot in recovery mode; found CSE in expected
SOFT TEMP DISABLE state, skipping EOP
[INFO ] Disabling Heci using PMC IPC
[WARN ] HECI: CSE device 16.0 is hidden
[WARN ] HECI: CSE device 16.1 is disabled
[WARN ] HECI: CSE device 16.2 is disabled
[WARN ] HECI: CSE device 16.3 is disabled
[WARN ] HECI: CSE device 16.4 is disabled
[WARN ] HECI: CSE device 16.5 is disabled
BUG=b:276339544
BRANCH=firmware-brya-14505.B
TEST=Tests on brya0 with and `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post sent soon after FSP-s and EOP message receive at
`BS_PAYLOAD_BOOT'. Verify robustness by injecting a
`GET_BOOT_STATE' HECI command with or without `heci_reset'. The
implementation always successfully completed the EOP before
moving to the payload. As expected, the boot time benefit of the
asynchronous solution was under some injection scenario
undermined by this unexpected HECI command.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I01a56bfe3f6c37ffb5e51a527d9fe74785441c5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This function calls into `set_feature_ctrl_lock()` to lock
IA32_FEATURE_CONTROL MSRfeature control.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9a03ee6786144dae6fd3a18bcc53cb62919dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This function calls into `set_feature_ctrl_vmx_arg()`
to enable VMX for virtualization if not done by FSP (based on
DROP_CPU_FEATURE_PROGRAM_IN_FSP config is enabled) in MeteorLake
SoC based platform.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7e49c15fd4f78a3e633855fea550720f0a685062
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This function performs locking of the AES-NI enablement state.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I16f1c14d8a0ca927a34c295cb95311bd4972d691
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch calls into API to disable 3-strike error on
Meteor Lake SoC based platform.
TEST=Able to build and boot google/rex to ChromeOS.
Dumping MSR 0x1A4 shows BIT11 aka 3-strike error is disabled
```
localhost ~ # iotools rdmsr 0 0x1a4
0x0000000000000900
```
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5c33a1fa2d7e27ec8ffdea876edbb86adc3b45b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch introduces a new config named
`DROP_CPU_FEATURE_PROGRAM_IN_FSP` to avoid FSP running basic CPU
feature programming on BSP and on APs using the "CpuFeaturesPei.efi"
module.
Most of this feature programming is getting performed today in scope
of coreboot doing MP Init. Running this redundant programming in
scope of FSP (when `USE_FSP_FEATURE_PROGRAM_ON_APS` config is enabled)
results in CPU exception (for example: attempting to reprogram CPU
feature lock MSR is causing CPU exception).
SoC users should select this config after dropping "CpuFeaturesPei.ffs"
module from FSP-S Firmware Volume (FV). Upon selection, coreboot runs
those additional feature programming on BSP and APs.
This feature is by default enabled, in case of "coreboot running MP
init" aka `MP_SERVICES_PPI_V2_NOOP` config is selected.
At present, this option does not do anything unless any platform
eventually decides to drop FSP feature programming module and choose
coreboot CPU feature programming over it.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3be5329390401024d7ec9eed85a5afc35ab1b776
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
In Intel designs, internal processor errors, such as a processor
instruction retirement watchdog timeout (also known as a 3-strike
timeout) will cause a CATERR assertion and can only be recovered from by
a system reset.
This patch prevents the Three Strike Counter from incrementing (as per
Intel EDS doc: 630094), which would help to disable Machine Check Catastrophic error. It will provide more opportunity to collect more useful CPU traces for debugging.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I286037cb00603f5fbc434cd1facc5e906718ba2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74158
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Restrict DPTC to 15W boards, since we only have 15W values defined in
the devicetree. This will revert the 6W boards back to their default
values, rather than (incorrectly) configuring them with 15W values.
BUG=b:253301653
TEST=Verify DPTC values are set for 15W boards
TEST=Verify DPTC values are set not set for 6W boards
Change-Id: I94f3974fce6358e3cbb0c30c1af33eb7ecb29ad7
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74127
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP will return the TDP in the format 0xX0000, where 'X' is the
value we're interested in. For example: 0xF0000 (15W), 0x60000 (6W).
Re-interpret the value so the caller just sees the TDP directly, without
needing to re-interpret things themselves.
BUG=b:253301653
TEST=Manually verify value is correct
Change-Id: I632e702d986a4ac85605040e09c1afab2bbdc59d
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74126
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is needed to generate MADT and SRAT where lapicid for threads need
to be added last. When CPUID leaf '0xB' is not present assume some
defaults that would result in identical ACPI code generation.
Change-Id: I2210eb9b663dd90941a64132aa7154440dc7e5a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69222
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On some systems the BSP cannot know how many CPUs are present in the
system. A typical use case is a multi socket system. Setting the enable
flag only on CPUs that actually exist makes it more flexible.
Change-Id: I6c8042b4d6127239175924f996f735bf9c83c6e8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68892
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Don't pass the stub params to the mp_init code.
Change-Id: I070bc00ae5e5bceb6c5b90ea833cc057dd41f6cc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64802
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In the current design the relocatable parameters are used to know the
offset of the 32bit startpoint. This requires back and forward
interaction between the stub, the loader and the mp init code. This
makes the code hard to read.
This is static information known at buildtime, so a better way to deal
with this is to generate a header that contains this offset.
Change-Id: Ic01badd2af11a6e1dbc27c8e928916fedf104b5b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64625
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's quite confusing to keep track of lapic ID inside the device
struct and initial lapic ID inside an array.
Change-Id: I4d9f8d23c0b0e5c142f6907593428d8509e4e7bb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64342
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently this is only used in bootblock and expects a fixed offset.
Change-Id: I3c4db6fffe3343f12383fe9585620ffefb01cf81
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
It will cache decoded EDID string in a static array. If called more
than once, a pointer to the static array is directly returned, without
reading EDID again.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ibdbe4d76f9b59e7ae83b60cda042c2d1c39827ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74180
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Drop devicetree setting X2apic as the same functionality is already
exposed in Kconfig.
To activate X2apic select X2APIC_ONLY or X2APIC_RUNTIME in
the "APIC operation mode".
Note: Your OS must have support for X2APIC. If you are using less
than 256 CPU cores select XAPIC_ONLY here.
Test:
- Booted to OS in X2APIC mode when X2APIC_ONLY or X2APIC_RUNTIME
was selected.
- Booted to OS in XAPIC mode when XAPIC_ONLY was selected.
Change-Id: I65152b0696a45b62a5629fd95801187354c7a93b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
When more than 255 CPU cores are present on a board
the X2APIC must be used.
Select DEFAULT_X2APIC_RUNTIME to support X2APIC by
default when a mainboard enables it in the devicetree.
Change-Id: I3e84cfbd2a7f05b142dc4d782764edce81646c8a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74184
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch renames debug FMD file (chromeos.debug-fsp.fmd) to
chromeos-debug-fsp.fmd in order to match the file path name in `FMDFILE`
config.
TEST=Able to build intel/mtlrvp with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic8de07e4befa6b1ab8ab57d593c6939d87c48e9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Usha P <usha.p@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Because Markarth PCIe port 1 use for eMMc not SD. So we need override
PCIe config for Markarth. And also the Markarth have NVMe and eMMC
SKU. Follow Winterhold to look at the NVMe CLKREQ signal before
initializing the ports allowing us to identify which device is populated
and only initialize that device.
BRANCH=none
BUG=b:275669215
TEST=emerge-skyrim coreboot chromeos-bootimage
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I0b4e4067a30019d742c7589a52badf93b7091615
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74133
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Inject ACPI code for all generated ASL templates.
This fixes ACPI errors shown in linux when not all sockets
are currently plugged in or some have been disabled.
Test:
Boot Archer City with CONFIG_MAX_SOCKET=4
Change-Id: I9562a37a92c6140a5623db3c8fb5972e6a90aaa4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74183
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
|
|
The RTD3 driver should have its 'use_rp_mutex' set in the devicetree.
BRANCH=firmware-brya-14505.B
TEST=boot to OS and check the generated SSDT table for the WWAN
The RTD3 RPMX mutex should be used in the reset Methods
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ic3fe20c56b67c2b5177f55f4845610087a30dc7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73381
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
When 'use_rp_mutex' (default = 0) is set in the device tree, a root
port mutex will be added. This mutex is used in _ON and _OFF method,
where the GPIO reset and/or enable GPIO value is changed. The
companion driver, such as WWAN driver, needs to acquire this root
port mutex when accessing the same GPIO pins. Using this common mutex
prevents those invoked methods from being called from different thread
while one is not completed.
An example is that WWAN driver calling _RST method to reset the device
and does remove/rescan for the device while the pm runtime work might
call RTD3 _OFF.
For those root port without additional driver, this mutex is not needed.
BRANCH=firmware-brya-14505.B
TEST=boot to OS and check the generated SSDT table for the root port.
The RPMX mutex should be generated and _ON and _OFF should use this
mutex.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ibc077528692b2d7076132384fb7bd441be502511
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
On Skyrim, there isn't a need for a sleep GPIO table. Remove the TODO
and filler table and function to reduce unnecessary function overhead.
BUG=None
BRANCH=Skyrim
TEST=Build Skyrim BIOS image.
Change-Id: Ia9d55a5e2295bb2e2c2957c4f5207362f616022c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
IF its first call is get_blc_pwm_freq_value(NULL), null dereference
will occur.
Now when the parameter is NULL, it will return the value of the static
blc_pwm_freq directly, so the original behavior is kept.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I32354aa0fe1a3ca725c2031f973ffad0bda81ad5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This reverts commit e7a1204f26fe3628de99b4ab4e3f32916565b95c.
This initial change was causing a boot failure when transitioning into
recovery mode.
BUG=b:276927816
TEST='emerge-brya coreboot chromeos-bootimage', flash and boot a skolas
SKU1 to kernel, then press Esc-Refresh-PowerButton to try to reboot into
recovery mode.
Change-Id: Ibebb20a000a239c344af1c96b8d376352b9c774e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74207
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 11f2f88a277124713f7b0023f078fcc2e1a98c32.
Revert initial change as it was causing a boot failure when
transitioning into recovery mode.
BUG=b:276927816
TEST='emerge-brya coreboot chromeos-bootimage', flash and boot a skolas
SKU1 to kernel, then press Esc-Refresh-PowerButton to try to reboot into
recovery mode.
Change-Id: I91c8d0434a2354dedfa49dd6100caf0e5bfe3f4c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74206
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the mode_switch.S
compilation unit to all stages that run on the x86 cores, but not to
verstage on PSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8950375d31557d9a38169869c1d250417261c31c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Use the 'verstage_x86' make target for the mode_switch.S compilation
unit instead of making adding it to the 'verstage' target depending on
VBOOT_STARTS_BEFORE_BOOTBLOCK not being selected. The only case where
VBOOT_STARTS_BEFORE_BOOTBLOCK is selected is the verstage on PSP case,
so I find using the 'verstage_x86' target here a bit easier to
understand.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iab618d4b9e325b07a648b91fcdce99c63644fbfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74196
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless build for Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23c6977ae8acebb8dcd546f86f7f7b677272a6cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74153
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless build for Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I181c3207bb1ebe9c5080ef3a3cdda8146ed05822
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74152
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the newly introduced 'all_x86' make target to add the compilation
unit to all stages that run on the x86 cores, but not to verstage on
PSP.
TEST=Timeless builds for Mandolin without verstage on PSP and Guybrush
with verstage on PSP result in identical images with and without this
patch applied.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94de6de5a4c7723065a4eb1b7149f9933ef134a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74151
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add the required CMOS entries for the mirror flag, so that it can
be enabled from a defconfig.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I174ac896df050480ee90c8141c5536b628c98432
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73682
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When enabled, the EC will mirror the firmware contained inside the
coreboot ROM. This allows it to be updated at the same time as
coreboot.
Enable the mirror flag if the installed EC firmware does not match
the target version or if a CMOS option, "manual_mirror_flag" is
set.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I377abbb37dc4d3e535e518a73e73969b25967daa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Some third-party SSDs, from Samsung and WD, such as the 990 Pro and
WD Black 850X aren't initialised by coreboot, seemingly as coreboot
is too quick; debug builds work, and enabling hotplug does.
Add a cmos option `pci_hot_plug`, defaulting to enabled to allow these
SSDs to work.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I680211bc87153a5e6005d58040a94725c0973451
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
ASPM is already configured by FSP so disable it in coreboot to
reduce boot time by a whopping 34ms.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I073c68dafa9baa90e253b5230f84b0de6a7e5c47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73982
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ic228b869aea362c1f07e0808c2735ff3b285a6bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73980
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This was added to solve Debian 10 not booting. Debian 10, which
now isn't the latest stable version works, so remove the
workaround that was included in the original port.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic11f355eb218ff3bad00fff83537c99c1b6985bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72669
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Alder Lake (ADL) and Raptor Lake (RPL) dptf settings for omnigul
BUG=b:273415170
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I8280f82ff1534ea63bcb448da231712bb4abd6d3
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This reverts commit ac69ce91229dee68d4135c596f49cf9e5efbe1e9.
Reason for revert: Removing breaks suspend in kernels > 6.2 and
Windows.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3e90266e66192b328b9af51c5e614774a248ddf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
|
|
Enables pre-cpu boot timestamps from cse.
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Boot on rex, check "cbmem -t"
Change-Id: I68cd53c18af6a400bcd9dc15d428a904b0647495
Signed-off-by: Bora Guvendik <bora.guvendik@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73759
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Get boot performance timestamps from CSE and inject them into CBMEM
timestamp table.
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Able to see TS elapse prior to IA reset on Rex
Change-Id: I548cdc057bf9aa0c0f0730d175eaee5eda3af571
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73713
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Boot to OS, check cbmem -t
Change-Id: I4d2da820f39c40ea864d15d25a94a68497b2af3d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74047
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CSE performance data timestamps are different for version 1
Alder Lake/Raptor Lake and version 2 Meteor Lake. This patch
moves the current ADL/RPL timestamp definitions to a separate
header file. It marks current structure as version 1.
BUG=b:259366109
TEST=Boot to OS, check ADL/RPL pre-cpu timestamps.
Change-Id: I780e250707d1d04891a5a1210b30aecb2c8620d3
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73712
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
This patch updates the MTLRVP flash layout to allow CSE Lite FW
update and accommodate multiple ESx SoC stepping blobs.
SI_BIOS:
SI_EC: Removed
RW_SECTION_A/B: Increased by ~1.9MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
Additionally, moved RW_LEGACY under extended BIOS region.
For chromeos-debug-fsp.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.2MB.
RW_LEGACY: Dropped
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
BUG=b:271407315
TEST=Able to enable CSE update on MTLRVP and have free space
to add one more PUNIT FW to support different SoC stepping.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I8cfba861e6d3122b0795a5a8e589c67cebad9762
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73378
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
Debug FSP is ~920KiB larger than release FSP and we don't have
sufficient space for MTL-P RVP flash layout.
Remove RW_LEGACY and split them into RW_SECTION_A/B so we can have a
room for it.
BUG=b:271407315
TEST=Build intel/mtlrvp with CONFIG_BUILDING_WITH_DEBUG_FSP.
Change-Id: Ief7dd39af018c4c1519ca80d1303085d8298cda6
Signed-off-by: Usha P <usha.p@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74193
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
Use the introduced EFI variable store driver on top of the SMMSTORE
region in SPI flash to read/write options.
Change-Id: I520eca96bcd573f825ed35a29bf8f750e313a02d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62562
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a driver to read and write EFI variables stored in a region device.
This is particularly useful for EDK2 as payload and allows to reuse
existing EFI tools to set/get options used by the firmware.
The write implementation is fault tolerant and doesn't corrupt the
variable store. A faulting write might result in using the old value
even though a 'newer' had been completely written.
Implemented basic unit tests for header corruption, writing existing
data and append new data into the store.
Initial firmware region state:
Initially the variable store region isn't formatted. Usually this is
done in the EDK2 payload when no valid firmware volume could be found.
It might be useful to do this offline or in coreboot to have a working
option store on the first boot or when it was corrupted.
Performance improvements:
Right now the code always checks if the firmware volume header is valid.
This could be optimised by caching the test result in heap. For write
operations it would be good to cache the end of the variable store in
the heap as well, instead of walking the whole store. For read
operations caching the entire store could be considered.
Reclaiming memory:
The EFI variable store is append write only. To update an existing
variable, first a new is written to the end of the store and then the
previous is marked invalid. This only works on PNOR flash that allow to
clear set bits, but keep cleared bits state.
This mechanisms allows a fault tolerant write, but it also requires to
"clean" the variable store for time to time. This cleaning would remove
variables that have been marked "deleted".
Such cleaning mechanism in turn must be fault tolerant and thus must use
a second partition in the SPI flash as backup/working region.
For now to cleaning is done in coreboot.
Fault checking:
The driver should check if a previous write was successful and if not
mark variables as deleted on the next operation.
Tested and working:
- Enumerate all existing variables
- Read variables
- Write variables
Change-Id: I8079f71d29da5dc2db956fc68bef1486fe3906bb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52564
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch avoids creating runtime ACPI for unused WIFI solutions.
For example: if the Rex SKU is with WIFI_CNVI then you don't need
to populate ACPI code for WIFI_PCIE.
FW_CONIG can be used for making those decisions.
TEST=No ASL entries being created for WIFI_PCIE if the FW_CONIG is
set to WIFI_CNVI.
Also, helped to save the boot time on google/rex (FSP-S API) by 9ms.
Change-Id: I60e4332d8d8c360fdf425b30513ff79209979e85
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74147
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Fix a typo in an enum's type name, "tmp" ---> "tpm". The enum type is
not used anywhere in the coreboot tree.
Change-Id: Ie7529e7ee80aa9661ec053da8211c2c3295b3942
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The i2c.c compilation unit is added to all stages in all cases, so use
the all target instead of adding it to all stages separately. Also order
the all targets alphabetically.
TEST=Timeless build on Mandolin results in identical image.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie90380075a3c87d226cdcb0f41f7e94275eaaa42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Glinda and Phoenix have different requirements, so split the birman
port_descriptors file to betty apply to each SoC.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia28cf4172b6adada10809e0135b2459077fa3da0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Set Type-A USB3 port0/1 tx_de_emp to 0x2B to fix the USB3 Gen2
RX signal integrity issue.
BUG=None
TEST=build FW and check Type-A USB3 port0/port1 RX pass
Change-Id: I9296ae5a8a9d7aa49b3c7529a9c1b2d2829b15d0
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
The Intel Power and Performance (PnP) team requested to update the
following:
- TDC settings for RPL-U 15W variant should be 22A.
- TDC settings for RPL-P 28W variant should be 33A.
BUG=b:275694022
BRANCH=firmware-brya-14505.B
TEST=PnP validated performance impact with these settings on both
RPL-U 15W and RPL-P 28W
Change-Id: I1141414785a990b975e32ebc03e490b83082aab7
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74046
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Baieswara Reddy Sagili <baieswara.reddy.sagili@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add CPU power limits support and values for RPL on Hades
BUG=b:269371363
TEST=builds
Change-Id: I22ef56152abe5a23067c5e923b07d60dc9fac8e7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73895
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CBFS location in memory is different than on the real hardware.
Change-Id: Icd806a57f449042c883b624056c05c1ff7e4c17e
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
|
|
Add override devicetree based on schematics(ver. 20230308).
BUG=b:272829190
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I9cd918c6a48cc6007a18c5aa94afe31fd9608718
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73974
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
The patch defines acpi_set_cpu_apicid_order() which orders the APIC IDs
based on APIC IDs of Performance cores and Efficient cores, calculates
the total core count and total Performance cores count, populates the
information in the cpu_apicid_order_info struct.
The helper function useful to present the Performance and Efficient
cores in order to OS through MADT table and _CPC object.
TEST=Verify the build for Gimble (Alder Lake board)
Change-Id: I8ab6053ffd036185d74d5469fbdf36d48e0021ce
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72131
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to document 640858 MTL EDS Vol2, bit 18 (PWR_PERF_PLATFRM_OVR) of MSR_POWER_CTL must be set.
This patch is backported from
`commit 117770d32468e63df ("soc/intel/
alderlake: Enable Energy/Performance Bias control")`.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic83225b619c49db0b49b521a83a2f1dc1ad69be8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74155
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This updates energy performance preference value to all logical CPUs
when the corresponding chip config is true.
This patch is backported from
`commit 0bb2225718ef898c ("soc/intel/alderlake: Add EPP override
support")`.
BUG=b:266522659
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8172276159fe3987dae36ec30ebceb76dd0ef326
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74154
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Indent with tabs for the sake of consistency with the rest of the code.
Change-Id: Ibd325a7a8348cc1f9023e54dceab40d02a0df233
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
