| Age | Commit message (Collapse) | Author |
|---|
|
Add PAD_NC_LOCK and PAD_CFG_GPI_SCI_LOCK macro to support mainboard
to lock NC and GPI_SCI pins as applicable.
BUG=b:216583542
TEST=build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie44d72f4152b55183d900228df3e3670358f7518
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61655
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On systems that use the first 128kByte of the SPI flash for the EC
firmware, it is not possible to place the EFS/amdfw part at the lowest
location in flash where the on-chip PSP firmware will look for the EFS,
since this is at an offset of 128kByte into the flash which is where the
cbfs master header resides when the main CBFS is placed right after the
EC firmware. This patch introduces the AMD_SOC_SEPARATE_EFS_SECTION
option that allows putting the EFS in a separate FMAP section that can
be located right after the EC firmware FMAP section. The EFS FMAP
partition is checked to ensure it begins at the expected location.
Change-Id: I5ed0f76c9c9c9c180ee5f1b96f88689d0979bb5e
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The patch defines USB2_PORT_MAX_TYPE_C macro to allow mark the type_c
flag.The USB2_PORT_MAX_TYPE_C macro modifies the USB2 configuration to
indicate the port mapped to Type-C and sets Max TX and Pre-emp
settings. This is an extension to existing macro USB2_PORT_MAX.
The change is required to enable port reset event on a USB2 port.
This event is passed to USB3 upstream ports to upgrade back to super
speed (USB3) after a downgrade during low power state.
BUG=b:193287279
TEST=Build the code for Gimble board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I464f139d8e367907191c04f9170ac53d327776ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61623
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch implements `cse_control_global_reset_lock()` as per ME BWG
(doc: 627331) recommendation.
It is recommended that BIOS should set this bit early on in the boot
sequence, and then clear it and set the CF9LOCK bit prior to loading
the OS in both an Intel CSME Enabled and a Intel CSME Disabled system.
Note: For CSE-Lite SKUs BIOS should set CF9LOCK bit unconditionally.
BUG=b:211954778
TEST=Able to build and boot Brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3894b2cd8b90dc033f475384486815ab2fadf381
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
The implementation of clearing watchdog status is wrong in CB:58835.
The value written to the 'wdt_mode' register should be
'wdt_mode | 0x22000000' instead of 'wdt_status | 0x22000000'.
BUG=b:204229208
TEST=check watchdog status is cleared.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I8c5dbaab2ac43d3867037bc4160aa5af2d79284f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
For most MediaTek SoCs (MT8183, MT8192, MT8195) we rely on an external
program (e.g., the "DRAM blob") to do the full DRAM calibration first,
then store and and apply the generated parameters to the reference
"fast DRAM calibration" in the vendor/mediatek folder for normal system
boot.
Starting with MT8186 the implementation of fast calibration may need
to be changed, and a "DRAM blob" only path is introduced for devices
that have to do both full and fast calibration using the external blob.
TEST=fast calibration pass on kingler/krabby
BUG=b:204226005
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: If25a7dd6aa6261ecff79a1b4df8b1f2e53d896dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Sabrina uses the same MMIO_CONF_BASE MSR as the previous AMD CPUs to
configure the PCI MMCONF base address.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7e3064bab5ca1e277b04f9aae98f9adabce75399
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change-Id: I7697512a63b58ca7d7200c74a409822389db0762
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Now that PSP verstage can directly write to the UART, we no longer need
to manually dump the cbmem contents.
Ideally if we can get picasso to add support for mapping the UART, or
if we implement bit banging we can delete this functionality
completely.
BUG=b:215599230
TEST=Boot guybrush and verify verstage logs aren't printed twice
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id70b24625c3b2f3d6fe470cf227a0083f5b974f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This will allow PSP verstage to write logs to the serial console. We
are no longer dependent on using a serial enabled PSP boot loader.
Ideally we would delete this psp printk and use the standard printk.
Since picasso doesn't currently support mapping the UART though, I'll
keep it for now.
BUG=b:215599230
TEST=Boot guybrush and verify PSP logs are output on serial console
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ibd77cc754fae5baccebe7adc5ae0790c79236d26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The Sabrina PSP doesn't support mapping the UART, so add a dummy
function to return NULL.
BUG=b:215599230
TEST=None
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idad8e4874e78bb96730feecb5a7b17334d12217c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The Picasso PSP doesn't support mapping the UART, so add a dummy
function to return NULL.
BUG=b:215599230
TEST=Build and boot morphius
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie1f033ff86ebb0f755a9a0b6ff293aa3c8bbbeb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This will allow directly using the UART console. On PSP releases that
don't support mapping the UART, we will just return NULL which is
perfectly acceptable.
BUG=b:215599230
TEST=Boot guybrush and verify verstage can print to the console
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic8d7f0fe00794a715756f92e3fb32c6b512cb8aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61607
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the console system itself will clearly differentiate loglevels,
it is no longer necessary to explicitly add "ERROR: " in front of every
BIOS_ERR message to help it stand out more (and allow automated tooling
to grep for it). Removing all these extra .rodata characters should save
us a nice little amount of binary size.
This patch was created by running
find src/ -type f -exec perl -0777 -pi -e 's/printk\(\s*BIOS_ERR,\s*"ERROR: /printk\(BIOS_ERR, "/gi' '{}' ';'
and doing some cursory review/cleanup on the result. Then doing the same
thing for BIOS_WARN with
's/printk\(\s*BIOS_WARNING,\s*"WARN(ING)?: /printk\(BIOS_WARNING, "/gi'
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3d0573acb23d2df53db6813cb1a5fc31b5357db8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Lance Zhao
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
SPL: Security Patch Level
The data in SPL is used for FW anti-rollback, preventing rollback of
platform level firmware to older version that are deemed vulnerable
from a security point of view.
BUG=b:216096562
Change-Id: I0aa456b8b4eec506fbb319293f0903b293325cb0
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
- Optional feature to provide mechanism to skip _OFF and _On execution.
- It is used for the device to skip _OFF and _ON during device driver
reload.
- OFSK is used to skip _OFF Method at the end of device driver removal.
- ONSK is used to skip _ON Method at the beginning of driver loading.
- General flow use case:
1. Device driver is removed by 'rmmod' command.
2. Device _RST is called. _RST perform reset.
3. Device increments OFSK in _RST to skip the following _OFF invoked by
OSPM.
4. OSPM invokes _OFF at the end of driver removal.
5. _OFF sees OFSK and skips current execution and decrements OFSK so that
_OFF will be executed normally next time.
6. _OFF increments ONSK to skip the following _ON invoked by OSPM.
7. Device driver is reloaded by 'insmod/modprobe' command.
8. OSPM invokes _ON at the beginning of driver loading.
9. _ON sees ONSK and skip current execution and decrements ONSK so that
_ON will be executed normally next time.
- In normal case:
When suspend, OSPM invokes _OFF. Since OFSK is zero, the device goes
to deeper state as expected.
When resume, OSPM invokes _ON. Sinc ONSK is zero, the device goes
to active state as expected.
- Generated changes:
PowerResource (RTD3, 0x00, 0x0000)
Name (ONSK, Zero)
Name (OFSK, Zero)
...
Method (_ON, 0, Serialized) // _ON_: Power On
{
If ((ONSK == Zero))
{
...
}
Else
{
ONSK--
}
}
Method (_OFF, 0, Serialized) // _OFF: Power Off
{
If ((OFSK == Zero))
{
...
}
Else
{
OFSK--
ONSK++
}
}
Test:
Enable and verify OFSK and ONSK Name objects and the if-condition logic
inside _OFF and _ON methods is added.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: Ic32d151d65107bfc220258c383a575e40a496b6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add L23 enter/exit, modPHY power gate, and source clock control methods.
DL23: method for L2/L3 entry.
L23D: method for L2/L3 exit.
PSD0: method for modPHY power gate.
SRCK: method for enabling/disable source clock.
These optional methods are to be used in the device ACPI to construct
flows with root port's power management functions.
Test:
Enable and verify DL23, L23D, PSD0, SRCK methods in ssdt.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I79de76f26c8424b036cb7d2719df68937599ca2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch defines enum values for small and big cores and uses them
to indicate the big or small core.
TEST=Verify the build for Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I740984a437da9d0518652f43180faf9b6ed4255e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Change-Id: Ieb362b5be05421b6ad2b2a3126c2943b7d55d135
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Sabrina is compatible with the common AMD UART block and also with the
DRIVERS_UART_8250MEM_32 driver it selects.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I432414c1d501ffbd1047b378996e06d281a9fb6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Sabrina is compatible with the common AMD SOC_AMD_COMMON_BLOCK_IOMMU
code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4c2e8553fde9467ca1b5e9085e36c33d138b7156
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This comment was added with the AMD family 15h Trinity IOMMU support in
commit 88ebbeb7e2a914330c869147bacb190b4270532f and looks like a copy of
the comment about the subtractive decode ranges in the LPC device. The
IOMMU doesn't have any subtractively decoded I/O or MMIO ranges and this
is also not what the code does. This resource is the MMIO region to
configure the IOMMU instead, so fix the comment in all copies of the
IOMMU support code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2e1e3a46b839b9e58b836932c1bc9b41b1b1dc02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Sabrina is compatible with the common AMD ACPIMMIO function block
mapping and access functions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I890375654a9cb1156e481c5586007ac81ab84120
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The PM2 ACPIMMIO region should only be accessed with 8 bit accesses.
Using 16 or 32 bit read accesses will return the data from the first
byte for all 2 or 4 bytes and 16 or 32 bit write accesses will result in
only the first byte being written which is both unexpected behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ace50d3b81b5bf3ea3b10aa02f25c58a6ea99b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Bit 23 in the PM_RST_STATUS register is called LtReset on Stoneyridge
and ShutdownMsg on Picasso/Cezanne/Sabrina. Bit 30 is reserved on
Stoneyridge and defined as SdpParityErr on the newer SoCs. Bit 31 is
only defined for Sabrina. Since the default value of undefined bits is 0
it isn't a problem to have descriptions for reserved reset status bits
on some SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0782116d327fcad3817a10eb237ac6c8294846b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Implementation for setup_lapic() did two things -- call
enable_lapic() and virtual_wire_mode_init().
In PARALLEL_MP case enable_lapic() was redundant as it
was already executed prior to initialize_cpu() call.
For the !PARALLEL_MP case enable_lapic() is added to
AP CPUs.
Change-Id: I5caf94315776a499e9cf8f007251b61f51292dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Sabrina has no SATA controller, so remove the corresponding PIRQ
mapping. This was verified with PPR #57243 Rev 1.53.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I98ffa3675c361e8a74c50ebfc37e79ae63dacc85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The common AMD data fabric register access code is valid for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I97fb2c6006c09297584845a83342e75058d35713
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The common AMD SMU code and the common AMD SMN access code that gets
selected by the common SMU code are valid for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic220dbb2f73b89554ac7e7b7e6dc7525ae8e9faa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The common AMD FCH AOAC bit definitions and helper functions are correct
for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie791cca0dc760e53e0f5c69c63ac78270ba6ad4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This change is added to address the issue of USB3 ports downgrading to
high speed during low power modes and not returning back to super speed.
The patch enables port reset event on USB2 ports. This event is
is passed to USB3 upstream ports to upgrade back to super speed (USB3)
after a downgrade during low power state
BUG=b:193287279
TEST=Built coreboot on Gimble and tested type A pen drive detects as
super speed device
Change-Id: Iabc6f308992bf3868da66f152c6d7b0164e64bea
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Sabrina uses an identical I2C controller as Picasso and Cezanne. Also
both the type and version read-only register of the I2C controller
contain identical values.
The dma_cr, dma_tdlr, dma_rdlr and clr_restart_det registers that are
defined in the dw_i2c_regs struct in the common Designware I2C code
aren't defined in the PPRs of Picasso, Cezanne and Sabrina, but since
common DW I2C code doesn't access those, this is no problem.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I90732aa98518010686f73f80bee229b13e9bc89c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
I2C bus 0..2 on Sabrina uses a different pad type which supports 1.1V
and 1.8V levels, but doesn't support 3.3V I2C levels. Compared to the
existing I2C pad control registers the bit definitions are different, so
add a separate function to configure those pads which however still has
the same function signature and is compatible with same data structs
used for the devicetree settings. PPR #57243 Rev 1.50 was used as a
reference.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie210c3437f2608d1e9fb99dcb151fc4190721375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This patch removes `gpios_to_lock` lists and `soc_gpio_lock_config`
override function from Alder Lake SoC as the required config
(SOC_INTEL_COMMON_BLOCK_SMM_LOCK_GPIO_PADS) to perform GPIO PAD lock
configuration using SMM is not enabled.
Note: The current assumption is that the responsibility of locking the
sensitive GPIOs (from getting reprogrammed by OS or other SW) remains
with the mainboard.
BUG=b:208827718
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2e22e8453b0ec7d34c0f7cb4c17e3336286581c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This patch removes mainboard capability to override GPIO PAD lock
configuration using `mb_gpio_lock_config` override function as the
variant GPIO pad configuration table is now capable of locking GPIO
PADs.
BUG=b:208827718
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6769f51afaf79b007d4f199bccc532d6b1c4d435
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This patch adds routines to keep CSE and other HECI devices into the
lower power device state (AKA D0I3).
- cse_set_to_d0i3 => Set CSE device state to D0I3
- heci_set_to_d0i3 => Function sets D0I3 for all HECI devices
Additionally, creates a config `MAX_HECI_DEVICES` to pass the HECI
device count info from SoC layer to common CSE block.
As per PCH EDS, the HECI device count for various SoCs are:
ADL/CNL/EHL/ICL/JSL/TGL => 6 (CSE, IDE-R, KT, CSE2, CSE3 and CSE4)
APL => 1 (CSE)
SKL/Xeon_SP => 5 (CSE, IDE-R, KT, CSE2 and CSE3)
BUG=b:211954778
TEST=Able to build and boot Brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie32887196628fe6386896604e50338f4bc0bedfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The I2C pad control registers of Picasso and Cezanne are identical and
the one of Sabrina is a superset of it, so factor out the functionality.
To avoid having devicetree settings that contain raw register bits, the
i2c_pad_control struct is introduced and used. The old Picasso code for
this had the RX level hard-coded for 3.3V I2C interfaces, so keep it
this way in this patch but add a TODO for future improvements.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1d70329644b68be3c4a1602f748e09db20cf6de1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9d098a55a5c6f6e022c3896750c752e2759e101b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
No mainboard in the current tree implements mainboard_i2c_override. In a
follow-up commit the i2c_pad_control struct is introduced to be able to
make more parameters controllable by devicetree settings in the future.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8f9ed5d50d26e4623dc5888cc8af090fdd00fc03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61566
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures PWRMBASE macro name and function to get PWRMBASE
address on APL SoC is aligned with other IA SoC.
PMC_BAR0 -> PCH_PWRM_BASE_ADDRESS
read_pmc_mmio_bar() -> pmc_mmio_regs()
Additionally, make `pmc_mmio_regs` a public function for other IA common
code may need to get access to this function.
BUG=None
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3a61117f34b60ed6eeb9bda3ad853f0ffe6390f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The functionality of disabling HECI1 device has been moved from the
FSP to coreboot (using `DISABLE_HECI1_AT_PRE_BOOT` config), hence,
always set the `Heci1Disabled` UPD to `0`.
BUG=none
TEST=Boot to OS, verify HECI1 is disabled on hatch system
using coreboot when mainboard selects DISABLE_HECI1_AT_PRE_BOOT config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia8908c080ca9991e7a71e795ccb8fc76d99514f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This flag only controls eSPI init in the PSP Stage 2 Boot Loader. It
doesn't control if port 80s are written. This flag also doesn't
currently control LPC init. The PSP is currently hard coded to remove
any LPC init.
BUG=b:215425753
TEST=build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idf3f0dcc216df2fd15b016f9458a208b7e15c720
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61534
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will allow verstage to write post codes.
BUG=b:215425753
TEST=Boot guybrush and verify PSP post codes are printed
22-01-31 15:12:03.214 (S3->S0)
22-01-31 15:12:03.214 03 04 0f 0e f0 f1 f2 01 10 a0 a2 <--new
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ceee8fcb094f462de99c07aef8e96425d9c3270
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61522
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option isn't meant to be assigned statically through devicetrees,
but at runtime according to some config mechanism. It works in
conjunction with the existing Kconfig option.
Change-Id: Ia760be61466bc6a0ec187746e6e32537029512b4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marvin Drees <marvin.drees@9elements.com>
|
|
This patch allows common CSE block to disable HECI1 device using PMC
IPC command `0xA9`.
Select SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PMC_IPC config for
Alder Lake to disable HECI1 device using PMC IPC.
Additionally, remove dead code that deals with HECI1 disabling using
in SMM as HECI1 disabling using PMC IPC is simpler solution.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I11a677173fd6fb38f7c09594a653aeea0df1332c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This patch allows common CSE block to disable HECI1 device using PMC
IPC command `0xA9`.
Select SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PMC_IPC config for
Tiger Lake to disable HECI1 device using PMC IPC.
Additionally, remove dead code that deals with HECI1 disabling using
in SMM as HECI1 disabling using PMC IPC is simpler solution.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Id5f1e3f622f65cd0f892c0dc541625bfd50d038e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Select HECI_DISABLE_USING_SMM config for Jasper Lake to disable HECI1
device using the SBI msg in SMM.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3e8568750ec941fc8b8e7407bad027f7175953c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Select HECI_DISABLE_USING_SMM config for Cannon Lake to disable HECI1
device using the SBI msg in SMM.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6882b619506d1bf4131f68c2c9a32ef4f7d6f6d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set the SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PCR config for
Apollo Lake to disable HECI1 device using PCR writes.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8df9544296f0bea095c5415805a596cb5b36885e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Set the SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PCR config for
Skylake to disable HECI1 device using PCR writes.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib6bfa7c48660a6df8d0944de675a4f30fe248d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Select HECI_DISABLE_USING_SMM config for Elkhart Lake to disable HECI1
device using the SBI msg in SMM.
BUG=none
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4ef7ff7aa234ce411092d70bcb2c9141609be90e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch provides the possible options for SoC users to choose the
applicable interface to make HECI1 function disable at pre-boot.
`SOC_INTEL_COMMON_BLOCK_HECI_DISABLE_USING_SBI` config is used for
disabling heci1 using non-posted sideband write (inside SMM) after
FSP-S sets the postboot_sai attribute. Applicable from CNL PCH onwards.
`SOC_INTEL_COMMON_BLOCK_HECI_DISABLE_USING_PMC_IPC` config is used for
disabling heci1 using PMC IPC command `0xA9`. Applicable from TGL PCH
onwards.
`SOC_INTEL_COMMON_BLOCK_HECI_DISABLE_USING_PCR` config is used for
disabling heci1 using private configuration register (PCR) write.
Applicable for SoC platform prior to CNL PCH.
Additionally, add PID_CSME0 macro for SKL, Xeon_SP and APL to fix the
compilation failure.
Finally, rename heci_disable() function to heci1_disable() to make it
more meaningful.
BUG=none
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7e0bab0004013b999ec1e054310763427d7b9348
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This patch export cse_disable_mei_devices() function instead of marking
it static. Other IA common code may need to get access to this function
for making `heci1` device disable.
BUG=none
TEST=Able to build and boot brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib2a1eb2fdc9d4724bd287b82be4238893c967046
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add platform_report_mode function which report current developer mode
status to the PSP. L1 widevine app in the PSP will use this information
to select key box.
BUG=b:211058864
TEST=build and boot guybrush
TEST=build picasso chrome os boards
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I04b5fcfa338b485b36f1b946203f32823385c0b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add svc_set_platform_bootmode svc to cezanne. PSP will use this
information to select proper widevine keybox.
BUG=b:211058864
TEST=build guybrush
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I6bcc9e49a2b73d486cfecd7b240bf989cad94630
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I6c093e8326733a079ab3c41dfd2c77fe1883a9d4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I8539eb9028f3141dfbeb926a1e19e3ad94be3edf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ifaaf8a240436758a83216037994493255935f158
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I8b5537bb6d0cb934aadb0eba8ba4f51dd53026c2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0ca7cbbf6c4884b58b4ec8a8e3cbc77f118a42f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib964939468ebb8cd0a537d514060ee5b8b13e320
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I59203253ba9e66e4db3ff5dcae347b68d1203f21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Using enum cb_err as return type instead of int improves the readability
of the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I55e6d93ca141b687871ceaa763bbbbe966c4b4a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
New platforms have additional Primary to Sideband bridge besides the PCH
P2SB. This change puts the common functions into the P2SB library.
BUG=b:213574324
TEST=Build platforms coreboot images successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I63f58584e8c3bfe42cdd81912e1e5140337c2d55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add a devicetree option to disable SATA Aggressive Link Power
Management. ALPM is a method of saving power. The corresponding FSP-S
UPD parameter is enabled by default. It may be that this feature is
unwanted, for example for a real-time system. Therefore, allow to
disable ALPM using the devicetree.
Change-Id: Ica8920a87ebebe83f5d8cb4d6c8c0a6105e183e4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add PCR_PSF3_TO_SHDW_PMC_REG_BASE for Alderlake-N.This value is updated
from the FSP code.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I7c788e149744bfae2c5260c996b16fc1ce2070c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61148
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Alder Lake N has eMMC storage device. Select SOC_INTEL_COMMON_BLOCK_SCS
Kconfig for Alder Lake N.
Change-Id: I577ffdc80ef09471309c827551a347d4397a33d1
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Alder Lake N has eMMC storage device. Add PCR Port ID for it.
Reference: Alder Lake N platform EDS Doc# 645548.
Change-Id: I6dc494d1748e66b8b4058954f127ec226863e8af
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add definitions for GPP_I GPIO group pins on Alder Lake N SOC and GPIO
IRQ routing information.
GPP_I GPIO group belongs to GPIO community 1. Hence GPIO community 1 in
Alder Lake N contains GPP_S, GPP_I, GPP_H, GPP_D GPIO groups.
GPIO groups 1-6 in Doc# 645550 Chapter 36 corresponds to GPIO
communities 5-0 respectively.
BUG=b:213535859
Change-Id: Ia71a399c03cb7d098a381bd9439d448e8a620761
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61106
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ADL has 4 TBT root ports which are PCIe compliant. TBT uses PCIe
coalescing logic where in case root port 0 is disabled, other enabled
root port is remapped to port 0.
coreboot handles this remapping scenarios for PCH and CPU PCIe root
ports and not for TBT root ports.
This patch uses the same function used for PCIe remapping to update
devicetree based on coalescing and SoC needs to pass correct function
number and number of slots.
BUG=b:210933428
BRANCH=None
TEST=Check if TBT remapping happens correctly and ACPI tables are
generated correctly.
Change-Id: Ied16191d6af41f8e2b31baee80cb475e7d557010
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
pcie_rp_update_devicetree function takes pcie_rp_group strcuture
as an argument and SoC code passes the parameter in this structure.
This pointer can be NULL and common code may try to dereference
this NULL pointer.
Also, group might have no data and SoC may pass this by indicating
group count as zero (For example, for CPU or TBT root ports).
These checks will prevent function from executing redundant code
and returning early from the call as it's not required.
BUG=b:210933428
BRANCH=None
TEST=check if function returns early for group count 0 and there is
no issue while booting board in case group count = 0.
Change-Id: I132319bb05fdef1590c18302fc64cc76e15bea6d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Commit 86302a806c5cc9b575424305e761753710417692 (soc/amd/{common,
cezanne,picasso}: Add PRE_X86_CBMEM_CONSOLE_SIZE) added this Kconfig
option before the initial commit that added soc/amd/sabrina as copy of
soc/amd/cezanne landed in the tree, so port the change forward to
Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2e8df5e7b7f1ac0af772e8c565f616a68b28e29e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch adds additional IGD device IDs as per document 638514.
BUG=b:216420554
TEST=coreboot is able to probe the IGD device during PCI enumeration.
Change-Id: I0cafe92581c454da5e4aeafd7ad52f0e65370b11
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61441
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch drops stale TODO comment about enabling eNEM on EHL.
eNEM is non-POR on the elkhartlake product.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I47fd755dec2324e05e6349e51e15abcf26967604
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Some registers of PMIC init settings are protected, so we failed to
set the correct value for init_setting. We disable protection before
setting PMIC init setting and enable it afterward.
BUG=b:216263707
TEST=PMIC setting value is set correctly.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I94d73d9c8a137444988e65c3709d29a3a4c03c5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61390
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modem uses different memory regions based on LTE/WiFi.
This adds correct carve-out to prevent region being disturbed.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 developement board
Signed-off-by: T Michael Turney <quic_mturney@quicinc.com>
Change-Id: I56bfb210606b08893ff71dd1b6679f1ec102ec95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Change-Id: Ib9670ee22e36dd988a75b2f8dc565534927b6107
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I61c695fb4fef3ae36ffc5a263236b9d40c299dc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
The recovery mode is meant to provide fixes for the platform deformity
hence, skip locking the GPIO PAD configuration to provide the same
flexibility to the platform owner while booting in recovery mode.
BUG=b:211950520
TEST=Able to build and boot the brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I0f0a3cfb2be7f2a5485679f6a3d8cb4fb407fcf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The existing TCSS registers access is through the REGBAR. There will be
future platforms which access the TCSS registers through the Sideband
interface. This change abstracts the common block API for TCSS access.
BUG=b:213574324
TEST=Build platforms coreboot images successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I3e2696b117af24412d73b257f470efc40caa5022
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Change-Id: I55682de4a1bc74f170e2044de35b0d8d53ef51ff
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
If the HECI1 PCI device is disabled, either via devicetree or other
method (HAP, me_cleaner), then we don't want/need to program a BAR,
set the PCI config, or call heci_reset(), as the latter will result
in a 15s timeout delay when booting.
Test: build/boot Purism Librem 13v2, verify heci_reset()
timeout delay is no longer present.
Change-Id: I0babe417173d10e37327538dc9e7aae980225367
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The patch defines the following helper functions:
get_cpu_scaling_factor(): Returns scaling factors of big and small core.
cpu_is_nominal_freq_supported(): Returns true if CPU supports Nominal
Frequency, otherwise false.
cpu_is_nominal_freq_supported(): Check CPU supports nominal frequency or
not.
The patch also enables CPPCv3 support for Intel Alder Lake which is
based on hybrid core architecture.
TEST=Verified Nominal Frequency and Nominal Performance are getting
updated for ADL-P small and big cores correctly.
Signed-off-by: Sridahr Siricilla <sridhar.siricilla@intel.com>
Change-Id: I963690a4fadad322095d202bcc08c92dcd845360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch implements ACPI CPPCv3 package. It implements and updates the
following methods:
generate_cppc_entries(): Updates method to support CPPCv3 package
acpi_get_cpu_nominal_freq(): Calculates CPU's nominal frequency
acpi_get_cpu_nomi_perf(): Calculates nominal performance for big and
small cores.
acpigen_write_CPPC_hybrid_method(): It generates ACPI code to implement
_CPC method.
acpigen_cppc_update_nominal_freq_perf(): It updates CPPC3 package if cpu
supports Nominal Frequency. It generates ACPI code which sets Nominal
Frequency and updates Nominal Performance. It uses below calculation to
update the Nominal Frequency and Nominal Performance:
Nominal Frequency = Max non-turbo ratio * cpu_bus_frequency
Nominal Performance = Max non-turn ratio * cpu scaling factor
CPU scaling factor varies in the hybrid core environment. So, the
generated ACPI code updates Nominal Performance based on the CPU's
scaling factor.
TEST=Verified CPPCv3 package is getting created in the SSDT table.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Signed-off-by: ravindr1 <ravindra@intel.com>
Change-Id: Icd5ea9e70bebd1e66d3cea2bcf8a6678e5cc95ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
The corresponding mainboard design guide was used as a reference here.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie61af7dab35b560d2eec1ea62058f3a4dad5cb0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The SMU message response register was moved compared to Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie384de52b1efb1d52f9018315a4b72916a4c9cee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iac1b7308851c34bd1556c02af6b270e9346073e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The Sabrina SoC doesn't have the PM_ESPI_CS_USE_DATA2 bit defined in the
PM_SPI_PAD_PU_PD register. It also doesn't have a physical LPC interface
any more, so there are no LPC pins that can be reconfigured as eSPI
interface.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I02bc8d007901c71942475fe707637c5da7227230
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The CPPC feature isn't available on the Sabrina SoC, so drop the
corresponding code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I71a1b0717571729ebca3600ac433e621cafc4e61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Also update mb/amd/chausie accordingly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idb4dcffa48c3dbdcffb66f1398b99ee96562efb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic0226afd9e7fffd6bf196f06ee6c34b6b9c92f30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There are no SATA controllers on the Sabrina SoC. The UPD field will be
removed later as a part of the initial UPD header update.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iedefd9f150e5bcb78173288e5fc9f1bbd6b498cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Some of the names have slightly changed in the PPR, but I kept the
current names for consistency across all AMD SoCs in coreboot. Revision
1.50 of the PPR #57243 was used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6bda656015858a57e221b8d7819f944c21564a39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The data fabric ID table in PPR #57243 Rev 1.50 has a different IOMS0
fabric ID than Cezanne.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I32890b5c03219f6ebf8180929d71ef726d382483
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Since we don't need to support PCI ID remapping for finding the correct
VBIOS binary for the integrated GPU, graphics.c can be dropped for now.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd5b678f472b3b5888353efd057203eb641be874
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Sabrina is family 17h model A0h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I01e02e3491fb90941c767058986da876bdf7ca1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Compared to Cezanne there are 3 more UART controllers. Revision 1.50 of
the PPR #57243 was used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I628b1a7a0930f3409acdcabda2b864d42bf6bd23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
The GPIO and GPIO MUX mapping as well as some GPIO to GEVENT mappings
have changed compared to Cezanne. Sabrina also doesn't have a remote
GPIO bank. Revision 1.50 of PPR #57243 was used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iabb85a3d24c881055e94400d08d01505df44a07a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Compared to Cezanne there are 3 more UARTs controllers. The PCI
interrupt index table in the new SoC's PPR #57243 Rev 1.50 doesn't
contain a PIRQ mapping for UART4. The reference code has a mapping for
this and it uses PIRQ mapping index 0x77 for UART4 and not for I2C5.
Since the I2C5 controller isn't owned by the x86 side and I didn't see
any mapping of the I2C5 controller into the x86 MMIO space, this seems
very plausible. Also add the corresponding fields to the ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I44780f5bc20966e6cc9867fca609d67f2893163d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch drops the CSE common code block from getting compiled
in bootblock without any SoC code using heci communication so
early in the boot flow.
BUG=none
TEST=Able to build brya, purism/librem_skl without any compilation issue.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib4d221c6f19b60aeaf64696e64d0c4209dbf14e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
