Age | Commit message (Collapse) | Author |
|
Add AUXADC controller driver code.
TEST=build pass
BUG=b:202871018
Signed-off-by: Guodong Liu <guodong.liu@mediatek.corp-partner.google.com>
Change-Id: I9fb7fd4903d67a2804c31ff404bc0486983c742f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
GIC (generic interrupt controller) defines architectural requirements
for handling all interrupt sources and common interrupt controller
programming interface.
GIC needs to be pre-initialized on MT8186, so we add this initialize
function.
TEST=build pass
BUG=b:202871018
Change-Id: I6bf439d0d9e1ca7130a69b9006b957afca8b133c
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59252
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Enable and setup USB drivers.
2. Pull up to a weak resistor for USB3_HUB_RST_L and we reset
the hub via GPIO149.
TEST=boot kernel from USB ok
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ifcc11d51b0c1e495477957111e6021ef8275f629
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use regulator interface to use regulator more easily.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ied43cba51036c62a120df2afffeb63b5d73f012b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add SPM register definitions so that other drivers can use them.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iec2b493e464be9d617226cc8a9875ee3ddb759de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Turn off L2C SRAM and reconfigure as L2 cache
Mediatek SoC uses part of the L2 cache as SRAM before DRAM is ready.
After DRAM is ready, we should invoke disable_l2c_sram to reconfigure
the L2C SRAM as L2 cache.
2. Configure DMA buffer in DRAM
Set DRAM DMA to be non-cacheable to load blob correctly.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: If56d29cdd7d9dfaed05e129754aa1f887a581482
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Move mtk_soc_disable_l2c_sram and mtk_soc_after_dram to common folder
which are the same between MT8192, MT8195 and MT8186.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I8f49214b932a8d28ed2ca0d764dc745fa8ad330d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add basic support for VCORE/VDRAM1/VDDQ of MT6366.
TEST=build pass
BUG=b:202871018
Signed-off-by: James Lo <james.lo@mediatek.corp-partner.google.com>
Change-Id: I22e30421560a32f4a9e15899e8150376b1414494
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change help text to "dual IO read mode" to reduce noun confusion.
Suggestion from this comment:
https://review.coreboot.org/c/coreboot/+/58837/comment/40a98af1_dce6bb2b/
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I54b81cdeba3b693451f66e003fb470c9f8c19ad9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add APU device apc driver and set up permissions.
APU has its own device apc for control access by domains.
For Domain 0, the access to the following slaves are restricted to
security read and write:
apusys_ao-2, apusys_ao-4, apusys_ao-5, apu_sctrl_reviser,
apu_iommu0_r1 apu_iommu0_r2, apu_iommu0_r3, apu_iommu0_r4
apu_iommu1_r1, apu_iommu1_r2, apu_iommu1_r3,apu_iommu1_r4
For VPU, D0/D5 are set as no protection, other domains are forbidden.
For other slaves, the D0 is no protection, other domains are forbidden.
BUG=b:203145462
BRANCH=cherry
TEST=boot cherry, check dump log and test permissions
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: If92d3b02ac4966332315b85d68e0f48c6a9fce85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use size_t for count variables.
Reduce debug log level and fix typo.
Fix commit: https://review.coreboot.org/c/coreboot/+/58794
BUG=b:203145462
BRANCH=cherry
TEST=boot cherry correctly
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: Ic03f71b7a9038edb5877ebd9b6aed5e9bd63c918
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59038
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPI controller drivers.
TEST=build pass
BUG=b:202871018
Signed-off-by: Ruwen Liu <ot_ruwen.liu@mediatek.com>
Change-Id: I59a885c4fa31b6e2921698eaa3b97dbdc3144946
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
EINT event mask register is used to mask EINT wakeup source.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel EINT upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I84946c2c74dd233419cb94f013a42c734363baf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add timer drivers to use timer function.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I6524e4dec4cbe7f7eb75a7940c329416559a03c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add PLL and clock init code, frequency meter and APIs for
raising little CPU/CCI frequency.
TEST=build pass
BUG=b:202871018
Signed-off-by: Chun-Jie Chen <chun-jie.chen@mediatek.com>
Change-Id: Id46d0708e7ba0c1a4043a5dce33ef69421cb59c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The NOR-Flash can be configured on SPI0 or TDM-RX GPIOs so we have to
provide an init function in SoC for the mainboard to select right
configuration.
TEST=boot to romstage
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I285ec64ace8b72a48ef1d481d366bd67cb9b0337
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add NOR-Flash drivers to pass verification of flash at verstage.
TEST=boot to romstage
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: If51d765e1fd4895f97898710ec6fa1374e1048fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58837
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add GPIO drivers to let other module control GPIOs.
TEST=build pass
BUG=b:202871018
Signed-off-by: Guodong Liu <guodong.liu@mediatek.corp-partner.google.com>
Change-Id: Ice342ab94397db8bc0fbbeb8fb5ee7e19de871ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58836
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MT8186 requires writing speical value to mode register to clear
status register. The flow of clear status is different from other
platforms, so we override mtk_wdt_clr_status() for MT8186.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I290b69573a8e58db76814e16b5c17c23413f1108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58835
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
mtk_wdt_clr_status is different for MT8186 and MT8195,
so we move this function to soc folder.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ia8697ffdca1e2d1443f2259713c4ab6fdf1b1a9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58834
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new folder and basic drivers for Mediatek SoC 'MT8186'.
Difference of modules including in this patch between MT8186 and existing SoCs:
Timer:
Similar to MT8195, MT8186 uses v2 timer.
EMI/PLL/SPI:
Different from existing SoCs.
TEST=boot from SPI-NOR and show uart log on MT8186 EVB
BUG=b:200134633
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I579f79c15f4bf5e1daf6b35c70cfd00a985a0b81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58640
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some enum variables of timer v2 are the same between MT8195 and MT8186,
so we move them to common timer_v2.h.
TEST=emerge-cherry coreboot
BUG=b:200134633
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I89891a19e622aa24783025e73c38c4ffa43aa166
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58829
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up APU mbox's functional configuration registers.
BUG=b:203145462
BRANCH=cherry
TEST=boot cherry correctly
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: I5053d5e1f1c2286c9dce280ff83e8b8611b573b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58794
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: I82f8e6e5f8ccb7f8246cae45a01a3ddd5f2966f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58244
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: If457f4a096cd63038bf6b40552aa3caaba33d5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58243
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These issues were found and fixed by codespell, a useful tool for
finding spelling errors.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ieafbc93e49fcef198ac6e31fc8a3b708c395e08e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58082
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ltiming and clock_div are not support for MT8173, so we separate them
to weak function: mtk_i2c_dump_more_info()
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I3228c6953be5fac18a76029702b878a34c7563f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58074
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. The original algorithm for I2C speed cannot always make the
timing meet I2C specification so a new algorithm is introduced
to calculate the timing parameters more correctly.
2. Some I2C buses should be initialized in a different speed while
the original implementation was fixed at fast mode (400Khz).
So the mtk_i2c_bus_init is now also taking an extra speed
parameter.
There is an equivalent change in kernel side:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/i2c/busses/i2c-mt65xx.c?h=v5.15-rc3&id=be5ce0e97cc7a5c0d2da45d617b7bc567c3d3fa1
BUG=b:189899864
TEST=Test on Tomato, boot pass and timing pass
at 100/300/400/500/800/1000Khz.
Signed-off-by: Daolong Zhu <jg_daolongzhu@mediatek.corp-partner.google.com>
Change-Id: Id25b7bb3a76908a7943b940eb5bee799e80626a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58053
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
BUG=b:192429713
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507c99b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57980
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Our MIPI panel initialization framework differentiates between DCS and
GENERIC commands, but the exact interpretation of those terms is left to
the platform drivers. In practice, the MIPI DSI transaction codes for
these are standardized and platforms always need to do the same
operation of combining the command length and transfer type into a
correct DSI protocol code. This patch factors out the various
platform-specific DSI protocol definitions into a single global one and
moves the transaction type calculation into the common panel framework.
The Qualcomm SC7180 implementation which previously only supported DCS
commands is enhanced to (hopefully? untested for now...) also support
GENERIC commands. While we're rewriting that whole section also fix some
other issues about how exactly long and short commands need to be passed
to that hardware which we identified in the meantime.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I09ade7857ca04e89d286cf538b1a5ebb1eeb8c04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
The eventlog requires RTC to provide correct timestamps, so we have to
turn on the config and add the common drivers.
BUG=b:199003609
TEST=check timestamp in 'mosys eventlog list'
BRANCH=none
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Change-Id: Ia382cd023fcbfdf2c1efeb7b32c0b99feb71effa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Disable external output reset signal in first WDT reset
to preserve WDT original reset reason for WDT issue in kernel stage.
2. After preserved WDT reset reason, do fully reset again by sending
external output reset signal.
BUG=b:194025005
TEST=boot to kernel ok and function test pass
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.corp-partner.google.com>
Change-Id: I5887a8312f4daab3cbd0a30fea0195670a932e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Sounds like we prefer to have this under drivers/ instead of device/.
Also move all MIPI-related headers out from device/ into their own
directory.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib3e66954b8f0cf85b28d8d186b09d7846707559d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Move bcd2bin() / bin2bcd() functions to commonlib/bsd/include/
Also, the license is changed from GPL to BSD.
This is because it is needed from "utils" (see CL in the chain).
For reference bin2bcd() & bcd2bin() are very simple functions.
There are already BSD implementations, like these ones (just to
name a few):
https://chromium.googlesource.com/chromiumos/platform/mosys/+/refs/heads/main/include/lib/math.h#67
http://web.mit.edu/freebsd/head/sys/contrib/octeon-sdk/cvmx-cn3010-evb-hs5.c
BUG=b:172210863
TEST=make (everything compiled Ok).
Change-Id: If2eba82da35838799bcbcf38303de6bd53f7eb72
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56904
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To reduce suspend power consumption,
1. Disable unused CLKSQ2.
2. Set CLKSQ_EN to sleep control for SPM 26M sleep control.
No bus clock when enter 26m sleep control, and only control
clock square by side band.
Signed-off-by: Chun-Jie Chen <chun-jie.chen@mediatek.com>
Change-Id: Ia9a1735d6f508ce35b9af2d67831a3474255198b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57043
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add HDMI low power setting to reduce power consumption.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ica91645789e5de3401131e7050d2b1ee06c535dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57042
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All boards that are trying to use MIPI panels eventually run into the
problem that they need to store physical parameters and a list of DCS
initialization commands for each panel, and these commands can be very
different (e.g. a large amount of very short commands, a few very large
commands, etc.). Finding a data format to fit all these different cases
efficiently into the same structures keeps being a challenge, and the
Kukui mainboard already once put a lot of effort into designing a
clean, flexible and efficient solution for this. This patch moves that
framework into a common src/device/mipi/ library where it can be used by
other boards as well. (Also, this will hopefully allow us to save some
duplicated work when using the same panel on different boards at some
point.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I877f2b0c7ab984412b288e2ed27f37cd93c70863
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Move DFD driver to common folder so MT8195 can also use it.
BUG=b:192429713
TEST=emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7937cddf5f3a66f9269a94301d3134e6f4f9f22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The MEDIATEK_DRAM_DVFS_LIMIT_FREQ_CNT only makes sense if DVFS
is enabled (e.g., MEDIATEK_DRAM_DVFS) so we should change it to
depend on that instead of selecting DVFS.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ib81e4e48e863616ed1e36cd5c0000f4e2cfb5456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add mt6359p vcore set/get support.
To adjust frequency of little core, we need to adjust voltage of vcore.
Signed-off-by: James Lo <james.lo@mediatek.corp-partner.google.com>
Change-Id: Ibf49390ba78870b834c6d0b64e3f0f30f3494f18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Select mmc storage config for cherry.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I67c8795b6e6fc121e8fe61c40da05593faa02d94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I39a4391c1d1e832d77b709f8f899bb1c6dcacd69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add basic devapc (device access permission control) drivers.
DAPC driver is used to set up bus fabric security and data protection
among hardwares. DAPC driver groups the master hardwares into different
domains and gives secure and non-secure property. The slave hardware can
configure different access permissions for different domains via DAPC
driver.
1. Initialize devapc.
2. Set master domain and secure side band.
3. Set domain remap.
4. Set default permission.
Change-Id: I3677657a117caed0d73526f78b0ebe8180148335
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The GENMASK is defined in multiple files (with various names such as
MASKBIT), which sets certain consecutive bits to 1 and leaves the others
to 0. To avoid duplicate macros, add GENMASK macro to helpers.h.
GENMASK(high, low) sets bits from `high` to `low` (inclusive) to 1. For
example, GENMASK(39, 21) gives us the 64-bit vector 0x000000ffffe00000.
Remove duplicate macro definitions. Also utilize GENMASK for _BF_MASK in
mmio.h.
BUG=none
TEST=make tests/commonlib/bsd/helpers-test
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: If2e7c4827d8a7d27688534593b556a72f16f0c2b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
With the new definition of mt6360_regulator_id,
merge the MT6360 LDO and PMIC interfaces into one.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7ccc32cb0a9481d5f55349c152267a44fe09d20a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
On MT8195 platforms with BC1.2, we have to use EC to control
MT6360 so the mt6360_regulator_id is redefined to match the
numbers defined in EC driver.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I9437edb9776442759ce04c31d315c3760078ffb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56434
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: Ic34f29d1692b94284b2cf6c5d91d323df736c76f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56204
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update IO driving setting for pmif spi.
Signed-off-by: James Lo <james.lo@mediatek.corp-partner.google.com>
Change-Id: I48268cda8845a591592d8ca828ffe492e6dfe0ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56166
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The dramc_param.h defines the header version,
structure and APIs for the DRAM calibration parameters
stored on the flash, and should be platform independent.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: Ib8a6ea1b6cf1538854890b653d5d9a934f7f687e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Enable DCM settings on the MT8195 platform.
DCM means dynamic clock management, and it can dynamically
slow down or gate clocks during CPU or bus idle.
Change-Id: Ib431a0334c157d440d6e89dcb154241d980d97ce
Signed-off-by: Garmin Chang <garmin.chang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Make use of the retry macro intruduced in CB:55778:
helpers: Introduce retry macro
(Change-Id: I421e4dcab949616bd68b3a14231da744b9f74eeb)
BUG=none
TEST=emerge-cherry coreboot
BRANCH=none
Change-Id: Ieaec95e20e5bb54fcd145007cc46f21c8b7e26d2
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: If2e9d8a4dcfad28c48a2b5fa7c92f70fae879e67
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add DPM_FOUR_CHANNEL option for 4 channel configuration for DPM.
Publicize reset_dpm() as dpm_reset() for external reference.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: If6e0d5c4d16a7ddd69c4a427488f8899870db327
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I51e8ebf5a75ac629bed51665e12bafa740b4b81d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Andrew SH Cheng <andrew-sh.cheng@mediatek.com>
Change-Id: Ieaf234f35f2b7d440bdf1e6ec4c455af7b311623
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55710
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add mt6691 buck control for DRAM to run fast calibration test.
It is needed to get and set voltage during testing.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Change-Id: I4fb9f7245d44383a6a3a0cf8d00f7f503cbdeb06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55575
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:189985956
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I37326ad053295aa4944c8291e4e7a7d69c8f3f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55573
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ddp (display controller) driver that supports overlay, read/write
DMA, etc. The output goes to display interface DP_INTF0 directly.
Add ddp gclast and output_clamp settings on mt8195 to support
multi-layer display.
BUG=b:189985956
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Change-Id: I9d5dd1025c4766218c2b1d86b9b1f97f2eab53d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55509
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add disp_dsc/disp_merge/dp_intf/edptx base addresses.
BUG=b:189985956
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Change-Id: I694da1449154e5b167c10d6d43d25ee2c5c0ec36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55332
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add API of TVD_PLL1 mt_pll_set_tvd_pll1_freq() for setting rate.
2. Add API of TVD_PLL1 edp_mux_set_sel() for mux sel.
3. Add eDP power domain control.
BUG=b:189985956
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I9e43e0ffeb7b8bcd1786a8d2f5acbf22d5ab501f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55346
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the offsets by MT8195 Register Map V0.2-1
chapter: 3.2 GPIO Controller (page 3272)
Control register names:
PUPD_CFG0
PU_CFG0
Signed-off-by: Zhiqiang Ma <zhiqiang.ma@mediatek.com>
Change-Id: I9b0f8a24756092a97933cc9d4ba13a9e79c73e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55163
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable auxadc on MediaTek mt8195 platform.
Signed-off-by: Zhiqiang Ma <zhiqiang.ma@mediatek.com>
Change-Id: Ie79420e20c9ed6155791b490e1b5e4b44a579a49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch adds support for loading SPM firmware from CBFS to SPM SRAM.
SPM needs its own firmware to enable SPM suspend/resume function which
turns off several resources such as DRAM/mainpll/26M clk when linux
system suspend.
TEST=program counter of SPM is correct value after booting up.
Change-Id: Ia0f9b9f86e44b293c1cc47213946304c64aea75e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55140
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
spm_parse_firmware can be shared by MT8192 and MT8195.
TEST=emerge-asurada coreboot;
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I54d9672aa9ee9078ec9fe3fa4f2e9fe860a50636
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55139
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load SSPM firmware and boot up SSPM in ramstage.
This adds 23ms to the boot time.
TEST=Load SSPM blob ok, and we can see some logs of SSPM from AP.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ia227ea9f7d58129068cb36ec2de7d9feb677006b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The SSPM driver can be shared by MT8183, MT8192 and MT8195.
TEST=emerge-{asurada, kukui} coreboot;
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: If9779853becb298eeeabb3dc6096bc474baae202
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55050
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load MCUPM firmware and boot up MCUPM in ramstage.
TEST=can see MCUPM log from AP console
Signed-off-by: alex.miao <alex.miao@mediatek.corp-partner.google.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I9e8c45ce7166644b94319ec2e7836d3d3c8008dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The MPUCM drivers can be shared by MT8192 and MT8195.
TEST=emerge-asurada coreboot;
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I07a66bcf5a149582f34df1cfd08b5514fc5c2eb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Set fsrc source to ulposc_d10 for 26m off low power scenario.
Signed-off-by: chun-jie.chen <chun-jie.chen@mediatek.com>
Change-Id: Ifb02d32820944d7cfbbf23de638e9a0e82b5e84d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54870
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ATF configuration to support multi-core.
TEST=boot to kernel with multi-core support.
BUG=b:177593590
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Id1ef29894fa3a6022574c3874dee62617133b12c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53898
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initialize DRAM in romstage and configure to support fast calibration.
Change-Id: I89b87be62c8e88ae4a620d56aa7a35e47f97952d
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54229
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove dram_cbt_mode in dramc_soc.h.
TEST=emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Idc4a3887c9cc3f77cbdd7282e2977f6df858817d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Xi Chen <xixi.chen@mediatek.com>
|
|
vpp_sel and ethdr_sel are vdosys clock source select mux.
Steps to change to support 4K source.
1. Change vpp_sel source to mainpll_d4 to run at 546MHz
2. Change ethdr_sel source to univpll_d6 to run at 416MHz
Signed-off-by: Nancy Lin <nancy.lin@mediatek.com>
Change-Id: Ib6518ed6204528489c41e7161534bbd3734ac851
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54082
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set DRAM DMA to be non-cacheable to load blob correctly.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I819d40431fc7c9e7549686736d9e70de1c1982f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54052
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable SCP SRAM to allow module in SCPSYS to access DRAM.
TEST=AFE acess DRAM successfully
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I40862f8d74e5aa17361f1c91ea31a10b0a4ffb31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54014
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setup APU mbox's functional configuration registers.
BUG=b:186369803
BRANCH=asurada
TEST=boot asurada correctly
Signed-off-by: Chien-Chih Tseng <chien-chih.tseng@mediatek.com>
Change-Id: If05a8af1a2f96598adcf70e15003e4f5dc94e337
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48622
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
eint event mask register is used to mask eint wakeup source.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
Change-Id: I703d87e3dc49cf4e0b7ff0c75a6ea80245dd73d3
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54007
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UFS reference clock (refclk) is enabled by default, which will cause
the UFSHCI to hold the SPM signal and lead to suspend failure. Since
UFS kernel driver is not built-in, disable refclk in coreboot stage.
Change UFSHCI base register to 0x11270000.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I1386e59f802a9e3c938a7e8dbeea547fbcb02709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Both mt8192 and mt8195 use MT659P RTC. Move mt8192/rtc.c to common
folder and rename to rtc_mt6359p.c.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I73ea90512228a659657f2019249e7142c673e68e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53897
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both mt8192 and mt8195 use mt6359p clk_buf.
But mt8195 clk_buf uses legacy co-clock mode without srclken_rc.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: Ie9ee91449a7a14e77231493f807b321b2dbaa6a6
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change-Id: I0ed82e860612e8a62f361e60d217280f775ab239
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53895
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=write/read EEPROM on MT8195 EVB successfully
Change-Id: Ia26e55512501e9758d7f5543d176730cf30ce03d
Signed-off-by: kewei xu <kewei.xu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53894
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Andrew SH Cheng <andrew-sh.cheng@mediatek.com>
Change-Id: I68ca7067f76a67c4e797437593539f8f85909edc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Mediatek SoC uses part of the L2 cache as SRAM before DRAM is ready.
After DRAM is ready, we should invoke disable_l2c_sram to reconfigure
the L2C SRAM as L2 cache.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I8777b0c8471fe17ffffdcb6ad5b7c00fb1d35db1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52925
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update domain remap setting to prevent DSP (domain 4)
from accessing registers.
Change-Id: Iefa9e75db85482a6c016b8b423c0b05f97e585b1
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: If7cd1f596f1406fa21d6586510e9956bb9846a6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
In follow-up patches, we need to set multiple power domains to
power on the display and audio on MT8195.
Move the power domain data under each SoC and make power_on() API
to support multiple settings.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: I8c3d19f1e9a4e516d674d68989ad509f37e5b593
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
TEST=boot to romstage on MT8195 EVB
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I450281fb4b1750e59cb76f6b2083f0e2889fd4cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add SPI controller driver code.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Change-Id: I674763cdb0f338e123c121ede52278cfe96df091
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The SPI drivers can be shared by MT8183, MT8192 and MT8195.
TEST=emerge-{oak, kukui, asurada, cherry} coreboot;
verified on Cherry P0
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7bb7809a88fbda67eca67ecfde45b9cb5f09dffe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
MT8195 also uses mt6359p so we can reuse most drivers.
The only differences are IO configuaration, clock setting, and PMIC
internal setting related to soc.
Reference datasheet: MT6315 datasheet v1.4.2.pdf, RH-D-2019-0616.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
Change-Id: I73f9c9bf92837f262c15758f16dacf52261dd3a3
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Configure ADSP domain from 0 to 4 and lock it to prevent
changing it unexpectedly.
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: Ib938ba05e8d0342572c57366c97ebb0185da8aba
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52728
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PLL and clock init code.
Add frequency meter and API for raising little CPU/CCI frequency.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Change-Id: I8ded0236d10826687f080bd5a213feb55d4bae03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52667
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PMIC drivers can be shared by MT8192 and MT8195.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ie17e01d25405b1e5119d9c70c5f7afb915daf80b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Po Xu <jg_poxu@mediatek.corp-partner.google.com>
Change-Id: Ica1b1c80a851075599442298bb6675caf5c72f57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
TEST=emerge-{oak, kukui, asurada, cherry} coreboot;
verified on Asurada and Cherry P0
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ic6a87e7d5983bf14ad123de82ed670a22a7be1aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52541
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A complete SPM register definition is defined in include/soc/spm.h.
Remove the redundant definition from include/soc/pmif_spmi.h.
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: If55e7adabdf32bb4312b910dce9a55621a8da380
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add register definitions for infracfg_ao, topckgen, apmixed and SPM.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ie740f22aa12f40950a27a3e0142e2d50a506b251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
MT8195 requires writing speical value to mode register to clear
status register. This value is invalid on other platforms. We can
do this safely in the common watchdog driver.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Iba5b41f426fc38719bb343a220e0724bff229c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I28eb13edcded95a9a4c17bdf92da9f792883a613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|