| Age | Commit message (Collapse) | Author |
|---|
|
Drop RMRR entry for XHCI controller since it's not under BIOS control.
There's no USB-PS/2 emulation done in SMM, hence it's not needed.
TEST=intel/archercity CRB
Change-Id: I5afd68371d71a00988fe0f8a6045ec5ce2adc6a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81297
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
Let ACPI DSDT figure out by itself if a stack is enabled.
Allows to drop uncore_fill_ssdt() on all platforms.
TEST=intel/archercity CRB
Change-Id: Ib9051d608147f2de228509ff6b13871ca3183979
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81273
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
As of now coreboot only supported one PCI segment group and thus the
MMCONF size had to be limited to 256 buses on ibm/sbp1. Since the
default FSP doesn't allow to disable unused IIO stacks a patched
version had to be used. Those unused IIO stacks consume lots of PCI
bus ranges, leaving no free buses for the secondary side behind PCI
bridges. The IIO disable mechanism doesn't work after ACPI G3 exit
and thus requires multiple reboots when the previous state was G3.
Since coreboot now supports multi PCI segment groups enable 512
MMCONF buses on 4S platforms by default and drop the IIO stack
disable UPDs on ibm/sbp1. This allows to boot faster without the
need for a patched FSP.
The use of multiple PCI segment groups might prevent legacy software
from working properly, however the only board where multiple PCI
segment groups are used uses u-root as default payload.
TEST=Booted on ibm/sbp1 to ubuntu22.04 using two PCI segment groups.
TEST=intel/archercity CRB
Change-Id: I4e6e5eca1196d4ab50e43b4b58d24eca444ab519
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add PCI enumeration support by reading the PCIeSegment reported in the
FSP HOB and add it when creating the PCI domain for each stack.
The PCI enumeration will be able to scan the additional PCI segment
groups and properly handle those devices.
TEST=Booted on ibm/sbp1 with multiple PCI segment groups enabled
to ubuntu 22.04.
TEST=intel/archercity CRB
Change-Id: I0ba5e426123234979d746d3bdfc1ddfbd71c3447
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79878
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For every PCI segment group generate a new SATC header.
Allows to generate proper ACPI code when multiple PCI segment
groups are enabled.
TEST=Booted on ibm/sbp1 with multiple PCI segment groups.
Properly generates multiple SATC headers.
TEST=intel/archercity CRB
Change-Id: I93b8ee05a7e6798e034f7a5da2c6883f0ee7a0e5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The DMAR entries of type "PCI" have no "Enumeration ID" and thus
there's no need to print it. Drop all unused Enumeration IDs to
simplify the code and debug prints.
Document ID: Intel Virtualization Technology for Directed I/O
Architecture Specification, Rev. 4.0, Order Number: D51397-015
TEST=intel/archercity CRB
Change-Id: I009fbfb9f9d62855d351c5db2d3d88722b5dbfa2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81186
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the `SOC_INTEL_COMMON_BASECODE_RAMTOP` configuration
at the SoC level for all MTL devices. This change streamlines the
configuration process, avoiding redundant selections on individual
mainboards.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot functionality on google/ovis and google/rex.
Change-Id: I3aa3a83c190d0a0e93c267222a9dca0ac7651f9c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch refactors RAMTOP MTRR type selection to address a critical
NEM logic bug on SoCs with non-power-of-two cache sets. This bug can
cause runtime hangs when Write Back (WB) caching is enabled.
Workaround: Force MTRR type to WC (Write Combining) on affected SoCs
when the cache set count is not a power of two.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot on google/ovis and google/rex (including Ovis with
non-power-of-two cache configuration).
Change-Id: Ia9a8f0d37d581b05c19ea7f9b1a07933caa956d4
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81269
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves commonlib/stdlib.h -> commonlib/bsd/stdlib.h, since
all code is BSD licensed anyway.
It also moves some code from libpayloads stdlib.h to
commonlib/bsd/stdlib.h so that it can be shared with coreboot. This is
useful for a subsequent commit that adds devicetree.c into commonlib.
Also we don't support DMA on arm platforms in coreboot (only libpayload)
therefore `dma_malloc()` has been removed and `dma_coherent()` has been
moved to architecture specific functions. Any architecture that tries to
use `dma_coherent()` now will get a compile time error. In order to not
break current platforms like mb/google/herobrine which make use of the
commonlib/storage/sdhci.c controller which in turn uses `dma_coherent` a
stub has been added to arch/arm64/dma.c.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I3a7ab0d1ddcc7ce9af121a61b4d4eafc9e563a8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Rewrite the function by iterating IOMMU (Input/Output Memory
Management Unit) devices instead of iterating socket and stacks,
which is more aligned to coreboot infrastructure.
TEST=intel/archercity CRB
coreboot DRHD generation is compared, the order of sections are
changed as expected but the content is kept equvalient.
Change-Id: I700513e05181303cf3f4effc793a872eb23340cb
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81228
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Obtain IOMMU (Input/Output Memory Management Unit) info and
enumerate devices using device utils instead of FSP HOB interface,
which might change across SoC generations and no ambiguity across
multiple PCIe segments.
TEST=intel/archercity CRB
coreboot DRHD generation log no changes before and after
Change-Id: Ic5c404899172a0e4fba2721b8e8ca6c1f0856698
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81227
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pmc_gpe_init uses soc_get_gpi_gpe_configs to initialize dw0, dw1
and dw2. dw0, dw1 and dw2 are uninitialized before calling
soc_get_gpi_gpe_configs. This is error prone for some soc
implementations where soc_get_gpi_gpe_configs does nothing.
This patch is simple, just to assign zero values to dw0, dw1 and
dw0, to enhance the code robustness.
TEST=intel/archercity CRB
Signed-off-by: Gang Chen <gang.c.chen@intel.com>
Change-Id: I8a710a2ac1482eed8c11977d51b187d834122d26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81210
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In Xeon-SP, the domain0, which is located at stack0, usually needs
special handling due to the compatible devices on it (HEPT, IO-APIC
and legacy IOs). This patch adds util function detect whether a
give domain or stack is with such a role.
TEST=intel/archercity CRB
Change-Id: I2f26b4ac54091c24c554f17964502c364288aa40
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
For Xeon-SP, there are 4 main domain roles (PCIe/CXL/IOAT/UBOX).
This patch adds util function to check whether a given domain
belongs to one of these roles, or a give device belongs to
a domain of the specific role.
TEST=intel/archercity CRB
Change-Id: I6b31c29564c774c27e86f55749ca9eca057a0cfe
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Drop SoC specific code and use generic implementation provided
by pci_domain_fill_ssdt.
TEST=Booted on IBM/SBP1 to Ubuntu 22.04.
TEST=intel/archercity CRB
Change-Id: I8b0bc2eb02569b5d74f8521d79e0af8fee880c80
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80796
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Use CONFIG_MAX_SOCKET instead of the IIO_UDS hob.
Allows to drop the argument in Xeon-SP common layer.
TEST=intel/archercity CRB
Change-Id: I05ec127f2bf84d3c242c3b0bca9709a0a7a4b52b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81181
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Remove those MSVC compiler defaults checks so that the GCC defaults for
wchar_t can be used. The FSP interface does not depend on wchar_t.
TEST: the resulting binaries are the same for intel/mtlrvp
Change-Id: I0ee1abc7e9ba46665838b63a6cfe0f4aa300114c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
This reverts commit 6995efbd1b986d0426ca513fd2e56771dd489f16.
Reason for revert: Submitted out of order and broke the coreboot build:
src/soc/intel/xeon_sp/uncore_acpi.c:275:6: error: call to undeclared function 'is_dev_on_domain0'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
275 | if (is_dev_on_domain0(iommu)) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:343:35: error: call to undeclared function 'is_dev_on_ioat_domain'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
343 | if (CONFIG(HAVE_IOAT_DOMAINS) && is_dev_on_ioat_domain(iommu)) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:423:4: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
423 | assert(vtd_mmio_cap != 0xffffffffffffffff);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:423:4: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:455:3: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
455 | assert(ptr);
| ^~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:455:3: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:540:7: error: call to undeclared function 'is_domain0'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
540 | if (is_domain0(dev_get_pci_domain(dev))) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:546:2: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
546 | assert(iommu0);
| ^~~~~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:546:2: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
Change-Id: I8b66177119ea5f55913a16aae06a3dcb807c2c64
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This reverts commit 6833e8c01afc2827f150135f3805dc71820ddaa4.
Reason for revert: Submitted out of order and broke the coreboot build.
src/soc/intel/xeon_sp/uncore_acpi.c:275:6: error: call to undeclared function 'is_dev_on_domain0'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
275 | if (is_dev_on_domain0(iommu)) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:343:35: error: call to undeclared function 'is_dev_on_ioat_domain'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
343 | if (CONFIG(HAVE_IOAT_DOMAINS) && is_dev_on_ioat_domain(iommu)) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:423:4: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
423 | assert(vtd_mmio_cap != 0xffffffffffffffff);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:423:4: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:455:3: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
455 | assert(ptr);
| ^~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:455:3: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:540:7: error: call to undeclared function 'is_domain0'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
540 | if (is_domain0(dev_get_pci_domain(dev))) {
| ^
src/soc/intel/xeon_sp/uncore_acpi.c:546:2: error: indirection of non-volatile null pointer will be deleted, not trap [-Werror,-Wnull-dereference]
546 | assert(iommu0);
| ^~~~~~~~~~~~~~
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^~~~~~~~~~~~~~~~~
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^~~~~~~~~~~~~~~~~~~~~~
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^~~~~~~~~~~~~~~~
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^~~~~~~~~~~~~~~~~~~~~
src/soc/intel/xeon_sp/uncore_acpi.c:546:2: note: consider using __builtin_trap() or qualifying pointer with 'volatile'
src/include/assert.h:85:27: note: expanded from macro 'assert'
85 | #define assert(statement) ASSERT(statement)
| ^
src/include/assert.h:56:7: note: expanded from macro 'ASSERT'
56 | if (!__build_time_assert(x) && !(x)) { \
| ^
src/include/assert.h:27:40: note: expanded from macro '__build_time_assert'
27 | (__builtin_constant_p(x) ? ((x) ? 1 : dead_code_t(int)) : 0)
| ^
src/include/assert.h:105:2: note: expanded from macro 'dead_code_t'
105 | *(type *)(uintptr_t)0; \
| ^
Change-Id: If919d6fa578a82fbb6bc5e1fd2adf4e9f59cab95
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81232
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Rewrite the function by iterating IOMMU (Input/Output Memory
Management Unit) devices instead of iterating socket and stacks,
which is more aligned to coreboot infrastructure.
TEST=intel/archercity CRB
coreboot DRHD generation is compared, the order of sections are
changed as expected but the content is kept equvalient.
Change-Id: I4c1cbf8d8fc93f746640efc3a82c539dcb3fdee2
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Obtain IOMMU (Input/Output Memory Management Unit) info and
enumerate devices using device utils instead of FSP HOB interface,
which might change across SoC generations and no ambiguity across
multiple PCIe segments.
TEST=intel/archercity CRB
coreboot DRHD generation log no changes before and after
Change-Id: Idcfa899c764ffe51db5ed202ead07ad7b6868864
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81048
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove debug message since it's static information.
Remove additional uint_8 varience and return below settings
directly:
1. CONFIG_SOC_INTEL_USB2_DEV_MAX
2. CONFIG_SOC_INTEL_USB3_DEV_MAX
3. MAX_TYPE_C_PORTS
4. CONFIG_MAX_TBT_ROOT_PORTS
5. CONFIG_MAX_ROOT_PORTS
6. CONFIG_MAX_PCIE_CLOCK_SRC
7. CONFIG_SOC_INTEL_UART_DEV_MAX
8. CONFIG_SOC_INTEL_I2C_DEV_MAX
9. CONFIG_SOC_INTEL_COMMON_BLOCK_GSPI_MAX
BUG=none
TEST=Build and test on rex/karis, system can boot to OS
Change-Id: I26e882d2d9dcbef84718924aaab3864d89c58f39
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
For Xeon-SP, it's common pattern to find devices under specific
socket, stack and domain. This patch adds util function for
these operations.
TEST=intel/archercity CRB
Change-Id: I163eacae363334919fd66d571b7e0415e77bd52d
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Implement watchdog for intel based platform by filling ACPI Watchdog
Action Table (WDAT) table.
The WDAT ACPI table encompasses essential watchdog functions, including:
- Setting and retrieving countdown/timeout values
- Starting and stopping the watchdog
- Pinging the watchdog
- Retrieving the cause of the last reboot, whether it was triggered by
the watchdog or another reason
The general purpose register TCO_MESSAGE1 stores the reason for the most
recent reboot rather than the original register TCO2_STS. This is
because the firmware must clear TCO2_STS, and it can't be reused for
storing this information for the operating system.
The watchdog is designed for use by the OS through certain defined
actions in the WDAT table. It relies on the ACPI Power Management Timer,
which may result in an increase in power consumption.
BUG=b:314260167
TEST=Enable CONFIG_ACPI_WDAT_WDT and CONFIG_USE_PM_ACPI_TIMER in the
config. Enable CONFIG_WDAT_WDT in the kernel config. Build and deploy
both firmware and kernel to the device. Trigger the watchdog by
performing the command: “cat > /dev/watchdog”. Wait approximately 30
seconds for the watchdog to reset the device.
Change-Id: Iaf7971f8407920a553fd91d2ed04193c882e08f1
Signed-off-by: Marek Maslanka <mmaslanka@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
SATC is for RCiEPs (Root Complex Integrated EndPoints) but not
limited to IOAT domains. Rewrite the func by iterating all domains
and its RCiEPs. Currently the codes only support 1 PCIe segment.
TEST=intel/archercity CRB
coreboot SATC generation logs are unchanged before and after.
Change-Id: I1dfc56ccf279b77cfab4ae3457aa8799d2d57a34
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Signed-off-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81049
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SPR CXL IIO stack is divided into 2 PCI domains. The 1st domain
is a PCI domain with single bus number and PCIe RCiEPs (Root
Complex Integrated End Points) on it. The 2nd domain is a CXL
domain with remaining buses for CXL 1.0/1.1 end points and
possible SR-IOV (Single Root IO Virtualizaton) VFs (Virtual
Function) if any.
TEST=intel/archercity CRB
P.S. The SUT is not with CXL cards however we hope this refactor
could be integrated first as an improvement of the design.
Change-Id: I643bcfbae7b6e8cfe11c147cc89374bc6b4d5a80
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81099
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 829e8e65b939 ("soc/intel: Use common codeflow for MP init")
brokes `USE_INTEL_FSP_MP_INIT' by making `init_cpus' function
static. This function needs to be accessible from
src/drivers/intel/fsp2_0/fsp_mpinit.c.
TEST=Verified on Meteor Lake rex board
Change-Id: Idb8cdfef7b4279da2c7dff344c95fe446a605934
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add System Agent IDs for Raptor Lake SKUs based on RPL Datasheet
(Doc ID: 743844) & EDS Vol 1 (Doc ID: 640555).
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I805040c65852742f1bbc43b443e115bcb0a930aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81115
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With this patch, all domain creation logics are moved into the scope
of attach_iio_stack/chip_common.c for the ease of maintenance
and future SoC integration where the domain creation process for
specific stack types might be overridden.
TEST=intel/archercity CRB
1. Boot to CentOS 9 Stream Cloud.
2. Compare PCIe enumeration and ACPI table generation logs before and
and after this patch, no changes.
Change-Id: If06bb5ff41b5f04cef766cf29d38369c6022da79
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81098
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CnviWifiCore UPD exists for ADL (version 4263) and RPL
(version 4415). Remove the guard so it is set correctly.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I9943ee43a442a43d75e78d1551e46dcea39db357
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81079
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `platform_fsp_multi_phase_init_cb' callback is specific to FSP-S,
let's rename it 'platform_fsp_silicon_multi_phase_init_cb' to avoid
any confusion.
Change-Id: I86b69e2069f08023e6f48464f6df4593710aa9ee
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Do not generate empty mem32 resources for CPMx or HQMx stacks.
Switch existing arguments to make sure that base is bigger than
limit to indicate that the resource is invalid.
Change-Id: I679563e97c33c7ee35d402674972e55f521eafa8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80793
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
NUMA will be supported by SPR and future generations.
TEST=intel/archercity CRB
Change-Id: I0d494f8e560059d9c8d5338cef9a6ffe34e59e26
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
TEST=intel/archercity CRB
Change-Id: I285549daad87fe1ad6e8a94853e0a92cd5930e04
Signed-off-by: Li, Jincheng <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81041
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP memory type representations change across Xeon-SP SoCs.
This patch adds type check utils to abstract the differences.
TEST=intel/archercity CRB
Change-Id: I2f5f3c0f16dc50bc739146e46afce2e5fbf4f62c
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Signed-off-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Set the unused 'name' property of the domain device and store
the ACPI name. Every IIO stack can have multiple domain devices,
each owning a subset of the available bus range within the stack.
The name will be used in future changes to generate ACPI names
in SSDT code generation. It can also be used to identify the domain
type by looking at the first two characters of the name.
Change-Id: Ic4cc81d198fb88300394055682a3954bf22db570
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80792
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
Change-Id: Ic080ffe7912ad71c77af09d2f3d1d9b08d9ffac8
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
ACPI _PRT method was missing from PEG (SoC PCI-E) links, resulting in OS
complaining about interrupt routing.
'pcieport 0000:00:06.0: can't derive routing for PCI INT A'
'nvme 0000:04:00.0: PCI INT A: not connected'
'Interrupt: pin A routed to IRQ -2147483648'
TEST=Boot Linux and Windows 10 on TGL-H platform with PEG0/PEG1
populated with PCI-E devices - Radeon RX 7800XT and Kingston KC3000 NVME
SSD. Check logs and stability while running 3D application and disk
benchmark at the same time.
Change-Id: If102522efa1a67b362b14d859d9e27a37bad85a4
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80848
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Move MEM_ADDR_64MB_SHIFT_BITS from FSP headers to Xeon-SP common layer
to reduce the dependency.
TEST=intel/archercity CRB
Change-Id: I4e1a652ad58233f7514cb9b23813d75144b8d435
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Starting with Intel CPX there is a bug in the reference code during
the Pipe init. This code synchronises the CAR between sockets in FSP-M.
This code implicitly assumes that the FSP heap is right above the
RC heap, where both of them are located at the bottom part of CAR.
Work around this issue by making that implicit assumption done in FSP
explicit in the coreboot linker script and allocation.
TEST=intel/archercity CRB
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Change-Id: I38a4f4b7470556e528a1672044c31f8bd92887d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80579
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
Change-Id: Ib319643f6b0b91d8c5854da531e035d333f04d75
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80143
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the code to retrieve the UBOX bus numbers. Only keep
a minial function that works when called from socket0 to retrieve
the bus for UBOX(1).
Change-Id: I2b18f02f62b69ec7c73cd5665102cb6bfc6e64b5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80102
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
- Only compile code in ramstage
- Lock PAM on all sockets
- Instead of manually crafting S:B:D:F numbers for each PCI device
search for the devices by PCI vendor and device ID.
This adds PCI multi-segment support without any further code
modifications, since the correct PCI segment will be stored in the
devicetree.
Change-Id: Ic8b3bfee8f0d02790620280b30a9dc9a05da1be8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch marks CONFIG_SOC_INTEL_CSE_RW_VERSION as deprecated, as
future platforms will automatically determine the CSE RW version using
CSE RW partition.
BUG=b:327842062
TEST=CSE RW update successful on Screebo.
Change-Id: I8c3e5c759e4d9a43c3bce3a0c032086f17592a67
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80924
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch automates the process of determining the CSE RW version used
for the CBFS entry, eliminating the need for manual configuration in
CONFIG_SOC_INTEL_CSE_RW_VERSION.
How to get CSE RW Version:
1. Open CSE RW file as per CONFIG_SOC_INTEL_CSE_RW_FILE
2. Read offset 16 (0x10) to know the CSE version
3. Format:
- CSE_VERSION_MAJOR : offset 16-17
- CSE_VERSION_MINOR : offset 18-19
- CSE_VERSION_HOTFIX: offset 20-21
- CSE_VERSION_HOTFIX: offset 22-23
Benefits:
- Removes error-prone manual version updates.
- Prevents boot loops due to mismatched CSE RW versions (actual vs config)
- Eliminates the need for SKU-specific CSE version limitations.
BUG=b:327842062
TEST=CSE RW update successful on Screebo with this patch.
Example Debug Output:
[DEBUG] cse_lite: RO version = 18.0.5.2066
[DEBUG] cse_lite: RW version = 18.0.5.2107
Change-Id: I0165d81b0e4b38e0e097956f250bb7484d774145
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80923
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MRC_CACHE_USING_MRC_VERSION is irrelevant to the EDK2 binding version
and should not be enabled under specific version conditions, so select
this at SoC level.
Change-Id: I10594df7c8fdc5cfe9b68975e01ae65859735544
Signed-off-by: Jincheng Li <jincheng.li@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80728
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Instead of manually crafting S:B:D:F numbers for each PCI device
search for the devices by PCI vendor and device ID.
This adds PCI multi-segment support without any further code
modifications, since the correct PCI segment will be stored in the
devicetree.
Change-Id: I1dcad4ba3fbc0295d74e1bf832cce95f014fd7bf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80095
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of manually crafting S:B:D:F numbers for each PCI device
search for the devices by PCI vendor and device ID.
This adds PCI multi-segment support without any further code
modifications, since the correct PCI segment will be stored in the
devicetree.
Intel Document-ID: 735086
Intel Document-ID: 612246
Tested: On SPR 4S all PCU on all 4 sockets could be found and locked.
Change-Id: I06694715cba76b101165f1cef66d161b0f896b26
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80093
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Port fix from Alder Lake to not set/reset IOM MCTP during
D3 cold entry or exit.
Ports 5008d340033d ("soc/intel/adl: Remove IOM Mctp command from TCSS
ASL"):
> Recently as part of s0ix hang issue, it was found that sending IOM
> MCTP command as part of TCSS D3 Cold enter-exit sequence created an
> issue.
> We discovered that due to change in hardware sequence, ADL should not
> set/reset IOM MCTP during D3 cold entry or exit. This patch removes
> the bit setting from ASL file to prevent hang in the system.
> This patch also removes obsolete Pcode mailbox communication which
> is no longer required for ADL.
> BUG=b:220796339
> BRANCH=firmware-brya-14505.B
> TEST=Check if hang issue is resolved with the CL and no other
> regression
> observed
> https://review.coreboot.org/c/coreboot/+/62861
Test: build/boot drobit to Win11. Verify TCSS XHCI power management
working and USB Root Hub doesn't Code 43 in device manager
Change-Id: I40a537fd2b0c821caf282f52aaff1874f54325f1
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80719
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Port 9c348a7b7ea3 ("soc/intel/alderlake: Fix processor hang while plug
unplug of TBT device") from Alder Lake to fix a similar issue present
on Tiger Lake:
> Processor hang is observed while hot plug unplug of TBT device. BIOS
> should execute TBT PCIe RP RTD3 flow based on the value of
> TBT_DMA_CFG_VS_CAP_9[30]. It should skip TBT PCIe RP RTD3 flow, if
> BIT30 in TBT FW version is not set.
> BUG=b:194880254
> https://review.coreboot.org/c/coreboot/+/56503
Change-Id: Ie5409111d4239be86c0b153f01b4fe5fc6af352c
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80718
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Don't attempt to open a PMIO window for a resource which doesn't have
the IORESOURCE_ASSIGNED flag set, since there is no point in doing so
and there's a high likelihood that the base address is 0, which will
throw an error.
TEST=build/boot purism/librem_cnl (Mini v2), ensure no errors in cbmem
log for attempting to open a PMIO window for unaassigned resources with
base address 0.
Change-Id: Ifba14a8f134ba12d5f5e9fdbac775d4f82b4c4de
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Mainboards using Intel Twin Lake (TWL) SoC shall select
SOC_INTEL_TWINLAKE.
BUG=none
BRANCH=firmware-nissa-15217.B
TEST=Build and boot Google/Yaviks with Twin Lake kconfig enabled
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ie4c5d137ee54512313344f853e7ca66d1fd25003
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80688
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use uintptr_t for the IOAPIC base parameter of the various IOAPIC-
related functions to avoid needing type casts in the callers. This also
allows dropping the VIO_APIC_VADDR define and consistently use the
IO_APIC_ADDR define instead.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I912943e923ff092708e90138caa5e1daf269a69f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80358
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
System sleep time (SLP_S0 signal asserted) is measured in ticks, for
Alder Lake soc in 122us (i.e. ~8197Hz) granularity/ticks.
BUG=b:301854636
TEST=/sys/devices/system/cpu/cpuidle/
low_power_idle_system_residency_us" will show system idle residency time
Change-Id: I449f7ed0d9ef891ae5266e8fd784a063a75e38eb
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Since the ACPI code is looking for VtdBars, that only appear on
Vtd devices, search for the Vtd device in devicetree.
With the previous commit the VtdBar is now exposed as a resource
on the Vtd device and thus can easily be accessed and used.
Drop the FSP HOB parsing and just use coreboot native functions.
Allows the code to work with multiple PCI segment groups.
Change-Id: I2c752dc595ac4c901f2b3a96718e256e413c76a7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
Provide a helper function to locate PCI devices on a given socket
by their PCI vendor and device IDs and functions to return
information about the current device, like the corresponding stack
and socket.
In addition add functions to return "location" information, like stack
and socket affiliation.
This becomes handy when locating devices and generating ACPI code.
Change-Id: I266360588548ba579f46b228c4d5b3ae6e39a029
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80094
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Read the VtdBar and add it to the resources of the host bridge PCI
device. The BAR is already marked as PciResourceMem32 in the parent
PCI domain.
This allows easy probing for VTD devices with enabled VtdBars in the
next commit, without the need to look up the stack HOB.
Change-Id: Id579a94e653473f3dd0dccea6e33dc64f792d028
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
If a downstream LPC device (eg, SIO function) is disabled, we shouldn't
attempt to open PMIO windows for it, as those functions often have
unset IO bases (which default to 0), resulting in false errors like:
[ERROR] LPC IO decode base 0!
TEST=build/boot purism/librem_cnl (Mini v2), verify no LPC IO errors
in cbmem log for disabled SIO functions.
Change-Id: I92c79fc01be21466976f3056242f6d1824878eab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The get_gpio function in this file is both unused and it shouldn't use
a signed int to pass in the MMIO base address and offset.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3b08bad040ad175b37175ef21d0a0a29525c4478
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
As there are multiple Vtd devices, print the path of each when reporting
resource registers.
Change-Id: I5d3a6484ed7c7b9760fce0f3a02a15ca26c2cbd2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80549
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
The lower bit of the BAR might be used for something else,
like enable bits, so mask the lower 12 bits and align all
base address to 4K.
Confirmed that all BARs have a minimum alignment of 4K, so that
masking the lower bits doesn't change the reported address.
The alignment of the VTD BARs is:
- VTD_MMCFG_BASE_CSR 64 MiB
- VTD_MMIOL_CSR 1 MiB
- VTD_NCMEM_BASE_CSR 64 MiB
- VTD_TSEG_BASE_CSR 1 MiB
- VTD_BAR_CSR 4 KiB
Change-Id: I9a7b963c0074246616968dd15c147f4916297d59
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
IOAT logics are optimized out for non-IOAT platforms where
CONFIG(HAVE_IOAT_DOMAINS) as false.
This patch puts CONFIG(HAVE_IOAT_DOMAINS) check together ahead
of is_ioat_iio_stack_res() check in the corresponding if
statement to fulfill the optimization outs.
TEST=intel/archercity CRB
Change-Id: I2d16c6ff5320bc9195a1033b6d55e3d997b19b88
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80683
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ADL-M is not commercially available, so it can be removed.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If769989f7a0434e32ebbcc8eac9b965b70ca71ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The ACPI is adjusted based on SOFTWARE_CONNECTION_MANAGER, so set
the UPD to match this to avoid the connection type being mismatched.
If it's mismatched, the TBT port will time out.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8a99db165301ce08caf55aac0e33ca1994559d62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80486
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The base for this region is a magic number and none for the fields are
used, which likely means this was simply copied from a different
firmware.
Change-Id: I217bbd0b098cd15ef296854cc6262d651f11d10e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73183
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support for using ADL N 4-core MCH ID 0x4618.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I7b9fc64ccf8e2401dcd55607e8f09b348efb3182
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80166
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Macros MAX_ACPI_MEMORY_AFFINITY_COUNT and MAX_SRAT_MEM_ENTRIES_PER_IMC
are ACPI table specific, and could be used across Xeon-SP SoCs.
This patch moves their definition from FSP header to Xeon-SP layer
ACPI header.
TEST=intel/archercity CRB
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Change-Id: I6c3a84b04a452bc8d4217947a7d12f050c94b56b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80629
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the definition of SRAT memory flags (SRAT_ACPI_MEMORY_ENABLED
and SRAT_ACPI_MEMORY_NONVOLATILE) from FSP header to ACPI common
codes.
TEST=intel/archercity CRB
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Change-Id: I6aa5c20c9556fd5d680406518d19a83801b0852c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
IOAT is the term for the on-chip accelerator technology of
Xeon-SP. In CPX and SPR, IOAT stack is also named as DINO stack.
Different SoC has different check criteria for IOAT stacks,
this patch introduces an util function to abstract these differences
as well as cleaning up the usage of names.
TEST=intel/archercity CRB
Change-Id: I376928ad89b68b294734000678dad6f070d3c97d
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80578
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I838ada7dfe948c58a5bb9805ade289b07368aa63
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch adds support for using ADL N 4-core MCH ID 0x4618.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3e4855ce93666c54ab35def9b58e4b13bc9a8672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch adds ADL N 4-core MCH ID 0x4618.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I47bd8fa991a48d30be4975b7965f2c3c859836dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80487
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iacfef5f032278919f1fcf49e31fa42bcbf1eaf20
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79920
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iea7f616f6db579c06722369c08de7cf7261dece8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79919
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only call fill_pds() once to prevent leaking memory. Previously it was
called for every active stack on every socket.
Only call dump_pds() once to prevent spamming the console with the same
information.
Drop the return value since it's always returning success.
Change-Id: Ifa9609e9da086dc9731556014ea9b320b270d776
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The struct map_entry has two zero'd entries due to the ifdef
being used. Do not read those entries and do not print those
entries.
Fixes a NULL string being printed along as the vendor and device
ID of the PCI device.
Change-Id: Id87ced76af552c0d064538f8140d1b78724fb833
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80546
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch eliminates coreboot from loading microcode from RW CBFS
(when the RO descriptor is locked, which indicates a fixed RO image)
because the kernel can already patch the microcode on BSPs and APs
while booting to OS.
This may be a chance to lower the burden on the AP FW side because
patching microcode on in-field devices is subject to firmware updates,
which are rarely published and, if required, must go through the
firmware qualification testing procedure (which is costly, unlike
kernel updates for ucode updates).
1. The FIT loads the necessary microcode from the RO during reset.
2. Reloading microcode from RW CBFS impacts boot time
(~60ms, core-dependent).
3. The kernel can still load microcode updates.
ChromeOS devices leverage RO+RW-A/RW-B booting. The RO's microcode is
sufficient for initial boot, and the kernel can apply updates later.
BUG=none
TEST=Verified boot optimization; in-field devices skip RW-CBFS microcode
loading when RO is locked.
Change-Id: Ia859809970406fca3fa14e6fa8e766ab16d94c8a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I8ebb915fbc21f82e39304473b0fcaa620559b5d5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80558
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an ACPI stub containing the TCPU device in proper scope, along with
the device status, on boards not using the DPTF driver, so that there
exists an ACPI device to be referenced from the PEPD LPI constraint
list.
Adding the stub fixes an AE_NOT_FOUND ACPI error under Linux for
_SB.PCI0.TCPU on boards with the SA thermal device enabled but which do
not use the Intel DPTF driver.
TEST=build/boot Linux,Win11 on purism/librem_cnl (Librem Mini v2).
Change-Id: I926d0461e5e0dfaf606102575c2be555a6bfb695
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This is now generated by acpigen in the common/block/sata module.
Change-Id: Ic45a059f47a090aa1993e83884408a82826b30cf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
acpi_device_path() includes the device name, so we end up with:
Scope (\_SB.PCI0.SATA) {
Device (SATA) {
...
Fix this by using acpi_device_scope() instead.
TEST=build/boot purism librem_cml (Mini v2), dump ACPI and verify
SATA device scope correct.
Change-Id: Ibbc8890d93b22f0ecba4b3a9b0531994574b3d55
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80554
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: Ie7bc4f3ae00bb9601001dbb71e7c3c84fd4f759a
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80596
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3fb4c6cfe24290c34682ff1c3396540465048727
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: Ie0d25eca75225ab33e6c15ef5ccb9073151f4148
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch increases the IgdDvmt50PreAlloc value as per Intel
recommendation starting with GFX PEIM 103x.
TEST=Able to build and boot google/rex.
Change-Id: I236b38a1ac5efbfcd23e373c09204d8a07b97618
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80406
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Rename tcss_mux_init to disconnect_tcss_devices to make it clear
what this function is doing, as it doesn't initialise anything.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I5e43f0cca9d49bc30fc189663490a306efd71584
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79874
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Improves code maintainability and potentially reduces redundancy by
using the IA common implementation.
Additionally, drop the unused macros from SoC local.
TEST=Build and boot successful on google/marasov.
Change-Id: I290fea99f04cfc9f18e5f1435ed07de42995869f
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80403
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Improves code maintainability and potentially reduces redundancy by
using the IA common implementation.
Additionally, drop the unused macros from SoC local.
TEST=Build and boot successful on google/screebo.
Change-Id: Ie0baae1d3b0093389649dee3531902c5e86c02fe
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80404
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This commit streamlines code and strengthens common code robustness
by moving the following SoC-layer functions to the common layer:
- sa_get_mmcfg_size: Retrieves the MMIO (Memory-Mapped I/O)
configuration space size by reading offset
0x60 of the PCI Host Bridge (D0:F0).
- sa_get_dsm_size: Calculates the size of the DSM (Device Stolen
Memory) by reading offset 0x50 of the PCI
Host Bridge (D0:F0) to determine pre-allocated
memory for the IGD (Integrated Graphics Device).
- sa_get_gsm_size: Calculates the size of the GSM (Graphics Stolen
Memory) by reading offset 0x52 of the PCI Host
Bridge (D0:F0).
- sa_get_dpr_size: Determines the size of the DMA Protection
Range (DPR) by reading offset 0x5C of the PCI
Host Bridge (D0:F0).
TEST= Build and boot successful on google/screebo.
Change-Id: Ic00e001563ec6f0d737a445964c716b45db43327
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Leverages common SA header definitions for Host Bridge registers.
Renames DSM_BASE_ADDR_REG to BDSM and DPR_REG to DPR for brevity.
Additionally, made some minor code alignment corrections while
adding newer macros in the header file.
TEST= Build and boot successful on google/screebo.
Change-Id: I476f213d75a0978336b3749a5ba1499107eb2238
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: sridhar siricilla <siricillasridhar@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Instead of S:B:D:F numbers pass the struct device to
acpi_create_srat_gia_pci and let it extract the information needed.
This also adds support for PCI multi segment groups.
Change-Id: Iafe32e98f0c85f14347695ccaa0225e43fad99e7
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80258
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of a BDF number store a pointer to the device itself.
Change-Id: I3fef93c5e54c8af792102bcd25364c43b554a5f0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This makes it easier to reuse, e.g. if you want to do it twice in one
assembly file.
Change-Id: Ida861338004187e4e714be41e17c8447fa4cf935
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In case where PAD_CFG_GPI_INT() is initialized with a pin value
lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community
the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin.
Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by
find_free_unique_irq() during IRQ assignment and assigned to other pins
which causes IRQ conflicts
BUG=b:322984217
BRANCH=None
TEST=Boot test on brox, check if correct IRQ assigned to EC
Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove hardcoded B:D:F numbers for the first socket and pass the PCI
addresses to be locked within SMM by using the smm_pci_resource_store.
This allows to lock down SMM on all sockets without knowing the actual
bus topology or PCI segment group at compile time where the UBOX devices
reside on.
Tested: SMM is locked on all 4 sockets instead of just one.
Change-Id: Ica694911384005681662d3d7bed354a60bf08911
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80247
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, SOC_INTEL_COMMON_BLOCK_TCSS will set MUX to disabled. The two
related options to re-configure it for either USB devices or displays,
are currently only supported by the ChromeEC. As such, any device
without the ChromeEC will boot with attached USB-C devices in a
non-functional state.
Add TCSS_HAS_USBC_OPS to make this feature configurable, and set the
default to enabled if the board features the ChromeEC.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia848668ae9af4637fc7cffec9eb694f29d7deba9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79882
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: If0397f5cc8d0f4f1872bd37a001fe42e0c37ec96
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80301
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
This patch moves the IP checksum algorithm into commonlib to prepare for
it being shared with libpayload. The current implementation is ancient
and pretty hard to read (and does some unnecessary questionable things
like the type-punning stuff which leads to suboptimal code generation),
so this reimplements it from scratch (that also helps with the
licensing).
This algorithm is prepared to take in a pre-calculated "wide" checksum
in a machine-register-sized data type which is then narrowed down to 16
bits (see RFC 1071 for why that's valid). This isn't used yet (and the
code will get optimized out), but will be used later in this patch
series for architecture-specific optimization.
Change-Id: Ic04c714c00439a17fc04a8a6e730cc2aa19b8e68
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80251
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
Instead of manually crafting S:B:D:F numbers for every
VTD device loop over the entire devicetree by PCI DEV IDs.
This adds PCI multi-segment support without any further code
modifications, since the correct PCI segment will be stored in the
devicetree.
Change-Id: I1c24d26e105c3dcbd9cca0e7197ab1362344aa96
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80092
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
Attach UBOX stacks on newer generation Xeon-SP.
In order to use PCI drivers for UBOX devices, locating UBOX devices
by vendor and device IDs and replacing device access by specifying
S:B:D:F numbers, add a PCI domain for the UBOX stacks and let the
PCI enumerator index all devices.
Since there are no PCI BARs on the UBOX bus the PCI locator doesn't
have to assign resources on those buses.
Once all PCI devices on the UBOX stack can be located without knowing
their UBOX bus number and PCI segment the Xeon-SP code can fully
enable the multi PCI segment group support.
Test: ibm/sbp1 (4S) is able to find all PCU devices by PCI ID.
Change-Id: I8f9d52dd117364a42de1c73d39cc86dafeaf2678
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80091
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
