| Age | Commit message (Collapse) | Author |
|---|
|
Now that power sequencing has been implemented, switch from using ACPI
"probed" flag to "detect" flag for all i2c touchscreens. This removes
non-present devices from the SSDT and relieves the OS of the burden of
probing.
TEST=build/boot Windows/linux on redrix?, verify touchscreen functional
in OS, dump ACPI and verify only i2c devices actually present on the
board have entries in the SSDT.
Change-Id: I0273014b2d164f67f503da7b968a09256bffb43c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74929
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For brya variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard). This will allow coreboot
to detect the presence of i2c touchscreens during ACPI SSDT generation
(implemented in a subsequent commit).
BUG=b:121309055
TEST=tested with rest of patch train
Change-Id: I8e56ac4834ce69de18bef2d34f5c361a7fda1aab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fix ethernet MAC address configuration. Currently, coreboot would
use ethernet_mac0 for both ports when setting the system's MAC
address. Instead, set the right device_index for the second controller
to pick up ethernet_mac1.
BUG=b:294856127
TEST=boot device and observe two different MAC addresses on the ethernet
ports.
Change-Id: I5ff6d62d2f837a120f7095f9b9aed487e6c5aee4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77044
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the RPL CPU power limits and system power limits based on
the suggestion of the thermal team for RPL SKUs.
The PL4 value suggested by the thermal team which is different from the reference document 686872.
BUG=b:292471206
BRANCH=firmware-brya-14505.B
TEST=built and booted into OS.
Change-Id: Ia030d13ca276c5e8340ae3b20d6e169bb162751d
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76769
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
|
|
Without setting these GPIO bits, you /can/ power on your board after
powering it down again. This includes after cutting the power.
The only way to recover from this is to pull the CMOS battery and cut
the power for 15mins. Then make sure you don't do this GPIO trickery or
you end up with the same state of basically an unresponsive "dead"
mainboard. So flash the chip before you pull the battery.
One small workaround I found when you like to flash from the system, is
to press the power button with 1 second after you enable power to the
board. In this small timeframe, apparently the superio chip didn't
intialise/restore/gets set with the settings that make it never want to
power on again. The other workaround is to connect the appriopriate
pins on the ATX power connector to force power to the mainboard.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I4c9df200ba3ec5f315ad3d184588551d29fa68ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Copy jack detect GPIO config of NAMI variant, which uses the same
codec for the external jack/mic. The internal pull-up isn't needed,
and fixes issue of high CPU usage under Windows.
TEST=build/boot google/rammus, verify jack detect functional under
both Win11 and Linux 6.x, no high CPU usage from excessive interrupts.
Change-Id: Ifbe23a6b33343e54b43879a8971c7cb6475cf1f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76947
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update eMMC DLL settings to prevent eMMC initialization error
BUG=b:290567342
TEST=warm/cold reboot stress test 2500 times pass
Change-Id: I418836ec3e2d2221c219eae35e2b22aeaacce4a5
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Update firmware to reflect schematics change for SD Card CLKSRC
from 7 to 6 for EVT board revision
BUG=b:291051683
TEST=emerge-rex coreboot
Change-Id: I3347f739650458c833d5a825742cf1d663853cc5
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77023
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The first platform samples came with IT8786E. The production units
switched to IT8784E in the final design.
Change the code to use IT8784E and reflect the proprietary firmware
configuration of the SIO chip.
TEST=Boot Ubuntu 22.04 on Protectli VP4670 (vault_cml) and dump the
configuration with superiotool and compare the configuration with
proprietary firmware.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5dc6669b592484e445c8c4bbe95d73f0a9f0392e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74175
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add ramstage.c in Makefile.inc and update boxy power limits in
Boxy ramstage.c.
BUG=b:290293153
TEST=emerge-dedede coreboot and check psys and PLx value on boxy
Change-Id: I4257dab358f066ebd13b6f251e8a5258a72fbd39
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76877
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All boards based on brya will have GFX devices to represent DRM
connectors in the kernel's /sys/class/drm/.
There should be no functional impact with or without this patch.
BUG=b:277629750
TEST=emerge-brya coreboot
Change-Id: I11afa9e8a1c8bf9f57bf6d195f07531182bd36f1
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
To help identify the licenses of the various files contained in the
coreboot source, we've added SPDX headers to the top of all of the
.c and .h files. This extends that practice to Makefiles.
Any file in the coreboot project without a specific license is bound
to the license of the overall coreboot project, GPL Version 2.
This patch adds the GPL V2 license identifier to the top of all
makefiles in the mainboard directory that don't already have an SPDX
license line at the top.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic451e68b1ad9ccdf34484dd98bd7fca7e177ef22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68982
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Select ENABLE_TCSS_USB_DETECTION for non-ChromeOS builds, to enable
booting from TCSS USB-C ports.
TEST=build/boot google/banshee, verify able to boot from all USB ports
using edk2 payload.
Change-Id: I998cc4a40950f43b4c511ead93ccc02c56c8367c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76945
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select ENABLE_TCSS_USB_DETECTION for non-ChromeOS builds, to enable
booting from TCSS USB-C ports.
TEST=build/boot google/drobit, verify able to boot from USB ports using
edk2 payload.
Change-Id: Ic6ab84dd5d1b980296eac043917d2cc7f14a5536
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Report CPU C10 state over eSPI so that the EC can use Virtual Wires to
detect if PECI can be used.
Change-Id: I301361f35caee8ba1c3fd9227219603897add92b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76910
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When lemp9 was converted to a variant in CB:64528, the Makefile was not
updated to handle the variant-specific `romstage.c`. This, as would be
expected, caused memory init errors and broke boot on CML-U boards.
Tested lemp9 boots to payload again.
Fixes: 5b7b04c938f2 ("mb/system76/cml-u: Convert lemp9 to a variant")
Change-Id: Ibc11d69a1662df653e6553421d67a9cd1b1d03e2
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
BUG=b:279097356
TEST=On dibbi:
- flash OS 15449.0.0 (where suspend is broken due to b:274531972)
- run `suspend_stress_test --count=1 --suspend_max=30 --suspend_min=28`
- check the AP wakes up immediately when the EC detects a sleep hang
Change-Id: I24a2aa5de1f76e6dd1c1ce726b648583756e5e55
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76938
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add PLx from JSL PDG(ID: 613095) in boxy devicetree.
BUG=b:290293153
TEST=emerge-dedede coreboot and read correct value on boxy CPU log:
CPU TDP = 6 Watts, CPU PL4 = 60 Watts
Change-Id: I7b063dc235fb714ba47eb620b914f2f9e92a2715
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76876
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add wifi sar table for craaskov
BUG=b:290739538
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib21f674b6749e125bf76a196902c994bfac15e65
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76576
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
_DSD "StorageD3Enable" property is needs to be set under the root
port in the DSDT or SSDT. The ACPI _DSD method is the preferred way
to opt D3hot support for storage devices.
This also bypasses the low LTR from SSD that blocking S0i2.2
LTR/latency SoC requirement.
Name (_DSD, Package () {
ToUUID("5025030F-842F-4AB4-A561-99A5189762D0"),
Package () {
Package (2) {"StorageD3Enable", 1},
// 1 - Enable; 0 - Disable
}
}
)
BUG=b:289028958
TEST=Check code compiles & boot rex, and verify the "StorageD3Enable"
SSDT entry.
Change-Id: I19decc2706954e73bc28fc2d9c3c4d18d2c384b7
Signed-off-by: Kangheui Won <khwon@chromium.org>
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76835
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch configures external V1p05/Vnn/VnnSx rails for Craaskov
to follow best practices for power savings – untested though.
* Enable the external V1p05, Vnn, VnnSx rails in S0i1, S0i2, S0i3, S3,
S4, S5 , S0 states.
* Set the supported voltage states.
* Set the voltage for v1p05 and vnn.
* Set the ICC max for v1p05 and vnn.
BUG=b:290165011
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Ibaf6a285788e26688d3d42691ab40052ef6d6cdb
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76926
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DPTF parameters were verified by the thermal team.
Based on thermal table in 290705146#comment11.
Set "tcc_offset" = "8"
BUG=b:290705146
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I2d9e1ad2e2fa98757d76578956101a482073885e
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76712
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
To be consistent with other boards setting the keyboard backlight at
boot.
Change-Id: I40d8ebe468a967f0dfe1e82bff9c63f1986699c7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76942
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This feature was originally present and then dropped, but turns out
that users prefer it. Set the backlight to 50% in romstage, back to
zero in ramstage; skip enabling on the S3 resume path.
TEST=build/boot google/eve, verify keyboard backlight turns on/off
as expected.
Change-Id: I33af888d614010538f69512bbd052ed2b83fcaa5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Move the jack detect GpioInt resources under the codec (where they
belong), but also leave a copy under LPEA for since the Linux drivers
(incorrectly) require them there. Add pin list for Windows' SST driver.
Adapted from the Intel ValleyView edk2 ACPI reference code.
TEST=build/boot Win11, Linux on google/swanky; verify audio functional
OOTB under Linux, under Windows with coolstar's drivers.
Change-Id: I51c07013fc20f07d2fd3639f7fbc2af0e0e490a0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76795
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
|
|
- add HRV and GpioIO for coolstar's windows drivers
- fix interrupt type for TI jack detect switch
TEST=build/boot Win11, Linux on google/cyan; verify audio working
OOTB under Linux, under Windows with coolstar's audio drivers.
Change-Id: I6bf6bb9e9989ca8f42436800666d95dd05799838
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76800
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Most of the components of this laptop are tested to work,
which is listed in the documentation.
Change-Id: Id8b3b7f735460c5e76a2dc9ab2d10154e6606ad6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46630
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Disable ASPM on ethernet, sd card, wwan, wlan, and ssd0 PCI devices.
This reduces kernel error logs such as:
[ 15.172613] r8169 0000:01:00.0: PCIe Bus Error: severity=Corrected,
type=Data Link Layer, (Transmitter ID)
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I7b1605f18a91ed20bfc6ab70547c415e0278d290
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
As of OS/FW: 15276.0.0 - Skyrim is not able to wake from S1/standby.
The wake issue either needs to be fixed, or S1 should not be advertised
as a capability in the ACPI table.
Select ACPI_S1_NOT_SUPPORTED to indicate that ACPI state S1 is not
supported on Skyrim devices. This results in 'standby' being removed
from /sys/power/state.
BUG=b:263981434
TEST=suspend_stress_test
TEST=frostflow-rev2 ~ # cat /sys/power/state
freeze mem
Change-Id: I85fcdca34187a8c275cf5a93beb931dfb27a7c87
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
C1-state auto demotion feature allows hardware to determine C1-state
as per platform policy. Since platform sets performance policy to
balanced from hardware, auto demotion can be disabled without
performance impact.
Also, disabling this feature results soc to enter PC2 and lower
state in camera preview case and save platform power.
Note: C1 demotion heuristics used EPB parameter to balance between power
and performance, i.e. low threshold when EPB is low in-order to get C1
demotion faster and vice-versa. ChromeOS operates at default EPB=0x7
(low EPB) in both AC/DC, so in DC mode it gets more C1 demotion hits
than expected (similar to AC mode) and losing power respectively.
BUG=b:286328295
TEST=Code compiles and correct value of c1-state auto demotion is
passed to FSP. Also verified PC residency improvement ~10% in
camera preview case.
Change-Id: I548e0e5340dec537d05718dd2f4652e10fb36ac0
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add support for SD card reader GL9750 and RTS5227S
BUG=b:284273384
TEST=emerge-rex coreboot
Change-Id: I98aa0d3e52c355f6c1528c912a6fa0f32652dda8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add the new memory support:
Samsung K4U6E3S4AB-MGCL
BUG=b:294151054
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/lp4x/gen_part_id.go JSL lp4x \
src/mainboard/google/dedede/variants/pirika/memory/ \
src/mainboard/google/dedede/variants/pirika/memory/\
mem_parts_used.txt"
Change-Id: Ief9bbf11fc05c8155f1da7188926a29dbbfbe488
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76542
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5d9133f2255a96c8367f69dcbb198a1a142cdb82
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add pirrha supported memory parts in mem_parts_used.txt, generate
SPD IDs for them.
1. K3KL8L80CM-MGCT (Samsung)
2. K3KL6L60GM-MGCT (Samsung)
BUG=b:292134655
BRANCH=nissa
TEST=FW_NAME=pirrha emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib3f5a5e5c8296f976d92f0196026d7bb63845664
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76881
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add more details to instruct future boards/models implementers regarding
how GFX devices should be added.
If HDMI and DP connectors are enumerated by the kernel in
/sys/class/drm/ then corresponding GFX device should be added to ACPI.
It is possible that some connectors do not have dedicated ports, but
still enumerated.
The order of GFX devices is DDIA -> DDIB -> TCPX.
BUG=b:277629750
TEST=emerge-brya coreboot
Change-Id: I59e82ee954a7d502e419046c1c2d7a20ea8a9224
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76776
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Add override devicetree based on schematics(ver. 20230714).
BUG=b:290248526
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id002282d91dc94b00f5d133203b62ca39d6cae6d
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76662
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This makes sure google/ovis don't get a random mac address on boot.
Additionally, program the LAN WAKE GPIO properly as per the Ovis
schematics dated July'23.
BUG=b:293905992
TEST=Verified on google/ovis that able to get the fixed MAC address across the power cycles.
Change-Id: I699e52e25f851de325f96ef885e04d15ca64badd
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76872
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for Samsung K4U6E3S4AB-MGCL.
BUG=b:293240969
TEST=emerge-dedede coreboot
Change-Id: I92a1f2110e74b5d25572e0e86e04b5b32112c1f5
Signed-off-by: tongjian <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Configure GPIOs based on schematics and confirm with EE.
BUG=b:290248526
BRANCH=None
TEST=emerge-nissa coreboot
Change-Id: I17fc9333a0ef592ea36b196b3fd417be47fb82bb
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
1. Joxer uses dptf.dv to distinguish 6W/15W by setting OEM variable.
2. Update passive policy and critical policy.
BUG=b:285477026, b:293540179
TEST=emerge-nissa coreboot and check the OEM variable.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I4e52ac624f7d7628cce3035a2bac67fc527bc167
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
|
|
Currently, S0iX test is failing because S0i2 susbstate is blocked.
Enable RTD3 for SSD to unblock S0i2.2 substate residency.
BUG=none
TEST=Screebo can enter into S0iX.
S0iX substate residency w/o this CL -
```
Substate Residency
S0i2.0 0
S0i2.1 38451594
S0i2.2 0
```
S0iX substate residency w/ this CL -
```
Substate Residency
S0i2.0 0
S0i2.1 12108
S0i2.2 33878424
```
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I50ac730820b3f29c387dc73bd90f1392a8797e24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Restrict ASPM to L1 for SD controller to avoid AERs.
BUG=b:288830220
TEST=No PCIE AER on SD controller on Screebo.
w/o this CL -
```
~ # lspci -s 00:06.0 -vvv | grep -i aspm
LnkCap: Port #9, Speed 16GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
~ # lspci -s 02:00.0 -vvv | grep -i aspm
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
~ # dmesg | grep -i -e "pci.*error"
[ 0.734597] pcieport 0000:00:06.1: AER: Corrected error received: 0000:02:00.0
[ 0.734882] rtsx_pci 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
[ 0.735258] rtsx_pci 0000:02:00.0: device [10ec:522a] error status/mask=00001000/00006000
[ 0.736159] pcieport 0000:00:06.1: AER: Corrected error received: 0000:02:00.0
[ 1.520903] pcieport 0000:00:06.1: AER: Corrected error received: 0000:02:00.0
[ 1.531587] rtsx_pci 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
[ 1.548894] rtsx_pci 0000:02:00.0: device [10ec:522a] error status/mask=00001000/00006000
[ 1.567490] pcieport 0000:00:06.1: AER: Multiple Corrected error received: 0000:02:00.0
```
w/ this CL -
```
~ # lspci -s 00:06.0 -vvv | grep -i aspm
LnkCap: Port #9, Speed 16GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
~ # lspci -s 02:00.0 -vvv | grep -i aspm
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
~ # dmesg | grep -i -e "pci.*error"
```
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I05f02c46486be42286fe9bc4f4be17763bb12b79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76829
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. H54G56CYRBX247
2. H9HCNNNCPMMLXR-NEE
3. MT53E1G32D2NP-046 WT:B
4. K4UBE3D4AB-MGCL
5. K4UBE3D4AA-MGCR
BUG=b:290811418
BRANCH=dedede
TEST=FW_NAME=cret emerge-dedede coreboot chromeos-bootimage
Change-Id: Ib7f23dc3604fe1869772d92c9d7b8cc32ed9bbb9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch chooses to show the early splash screen which is an
OEM feature. The current implementation is relying on the Intel
FSP GFX PEIM to perform the display initialization.
Having this feature allows the platform to show the user notification
with 500ms since boot compared to traditional scenarios where first
user notification is coming from kernel (typically ~3sec+ after cpu
reset). Eventually this feature will help to improve the user
experience while booting Intel SoC platform based chromeos devices.
BUG=b:284799726
TEST=Able to see the early splash screen on google/rex.
Change-Id: I399ddb6618e774302200e8a87629647ba070d080
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76361
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These devices are not present/used on CYAN boards.
Change-Id: I012b49562c2b932822823537032e2265901ddc81
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76799
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Ovis4ES variant supports only ESx SoCs. Existing Ovis variant will
support QS SoCs.
BUG=b:293409364
TEST=util/abuild/abuild -p none -t google/rex -b ovis4es -x -a
TEST=util/abuild/abuild -p none -t google/rex -b ovis -x -a
Change-Id: Iacf5ef6d3dfee8838fe13e68b254a84e4a6cf200
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76789
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch changes the `EC CONx Mapping` to fix the hot-plug issue
where attaching a device to USB-C port C1 can affect the USB-C
display over port C2.
Note: `PMC MUX Mapping` remains unchanged to reflect the underlying
board design where the physical MUX has swapped between C1 and C2
USB-C port.
Before:
| PMC MUX Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 3 | 1 |
| USB3-Port | 0 | 2 | 1 |
| EC CONx Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 3 | 1 |
| USB3-Port | 0 | 2 | 1 |
Physical Mapping between EC and SoC as below:
Port C0 - EC CON0 ----> PMC MUX CON0
Port C1 - EC CON1 ----> PMC MUX CON2
Port C2 - EC CON2 ----> PMC MUX CON1
After:
| PMC MUX Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 3 | 1 |
| USB3-Port | 0 | 2 | 1 |
| EC CONx Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 1 | 3 |
| USB3-Port | 0 | 1 | 2 |
Physical Mapping between EC and SoC as below:
Port C0 - EC CON0 ----> PMC MUX CON0
Port C1 - EC CON1 ----> PMC MUX CON1
Port C2 - EC CON2 ----> PMC MUX CON2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I59e2630bc0f93321cc4b734fcf3c4cf254882477
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Typically we set SaOcSupport to allow overclocking RAM, but addw2 saw a
high rate of errors when using the provided 3200 MHz DIMMs. Disable OC
so modules run at the standard 2933 MHz.
Change-Id: I469b9c73d2e6bfa0b3c9175bcc87584aeaa95f75
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform a codec reset to match all other System76 boards.
This applies commit 705ebbea0477 ("mb/system76: Reset Realtek codec
before configuring") to boards that were added later.
Change-Id: I618cc042f1803d07bfc067d1999e1c44ab4a1fa9
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Users report having the touchscreen as a wake device causes many
spurious wakeups due to proximity to the keyboard when the lid is
closed, so remove it as a wake source.
TEST=build/boot google/glimmer, observe no unintended wakeups when
the lid is closed.
Change-Id: Id16cabcd21afa0b373ecddd9eb3b0b8befb71576
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76794
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the ACPI SSID using Google's project campfire ID for EVE, to allow
coolstar's Windows drivers to identify the device (since it uses a
generic ACPI _HID). Custom drivers are necessary under Windows since
the touchpad firmware is not fully I2C-HID compliant.
TEST=build/boot Win11 on google/eve, verify touchpad fully functional.
Change-Id: I3b8d56ff01d4cca7ba5c02f1aaab1a7049607dbc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
|
|
CB:73353 switched ADL boards from using S0ix to S3. DevSlp can be
reenabled now as it no longer breaks suspend.
Change-Id: I618696833b7ed02e49c35d06021b730be91d879e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
System76 EC since system76/ec@99dfbeaec3b8 sets PL4 values through PECI
based on AC state for all boards. Remove the static PL4 value from
coreboot since it won't be used.
Change-Id: I2bc37f12aab11910b4fe029efcee891a93257529
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Do not reconfigured LSX0 so that the FSP values are used.
Change-Id: I76e2ab01a5e853e3c1ac78b471ea0aa87d703d52
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76751
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for vell board. Please refer Intel doc#723158 for
more information.
BUG=b:293535284
TEST=build and boot vell
Change-Id: I8a4d633fbd362188aedef373e515c7bfe5c4327a
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The EAPD pin needs to be enabled and set in order for the headphone
jack to work properly. It's already done for the speaker in the
beep verbs, but needs to be done for the HP jack as well in order
for output to work properly under Windows.
TEST=build/boot Win11 on LINK, verify headphone output functional
when headphones plugged in.
Change-Id: I411d7317aefc1154635c4c17ca0dc1e37c9f40f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76746
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the pirrha variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:292134655
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PIRRHA
Change-Id: Idc0a4dbb467cbdb91a5ed55c5e0a9e898e775b11
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76768
Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Vendor changes touchscreen firmware to use hid method instead of i2c.
BUG=b:274707912
BRANCH=None
TEST=emerge-nissa coreboot
Change-Id: I8e9e0b757e337db6af3fbf3cd4fdbc0079646179
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76680
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The EC serial port on these devices is not accessible to the end user
and exposing it to the OS via ACPI serves no purpose. Debugging over
the EC serial port (via the servo interface) does not require the
ACPI exist. Drop it since it's not needed and serves no purpose.
TEST=build/boot Win11 on auron/link/slippy, verify Windows Device
Manager no longer shows an unusable COM port.
Change-Id: If453bfca8e094aa06043293bdf91a40c38cc7866
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76793
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SX9324 register settings based on tuning value from SEMTECH.
－ Enable GPP_B5/GPP_B6
－ Enable GPP_H19 open irq
－ Adjust register reg_afe_ctrl0/reg_afe_ctrl3/reg_afe_ctrl4
BUG=b:292016304
BRANCH=None
TEST=Check register settings and confirm P-sensor function can work.
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I6f15f7a7c428aee45d35830574ef84aefcae6401
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76711
Reviewed-by: Kyle Lin <kylelinck@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add wifi sar table for constitution
BUG=b:291859402
BRANCH=firmware-brya-14505.B
TEST=emerge-constitution coreboot chromeos-bootimage
Change-Id: I8f99c5cf486cb3e1f2825bbe3a8084f2fe57a41a
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76674
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Lower the TCC Offset by 10 degress.
Change-Id: Ib80d3b73c41ec1196d8294c35b43333e0df218d5
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76374
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the SSID to allow the correct Creative Labs Windows audio drivers
to attach (vs generic HDA audio ones) and provide full functionality.
Linux doesn't care about the SSID, so changing it has no effect there.
TEST=build/boot Windows, Linux on google/link, verify the correct
audio drivers attach under Windows, no regressions under Linux.
Change-Id: Ib5e523b07583289b0222ef156245fb0771ad1f1c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76745
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set GPP_C6(TCHSCR_REPORT_EN) and GPP_C7(TCHSCR_INT_ODL) to NC for
non-touchscreen sku.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=build and boot to ChromeOS
Change-Id: Ie062eef24f640c3d6c4a0b4c77792e57ac3a722c
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Uldren will support internal fivr in next phase and using fw_config to
decide the board with internal or external fivr.
BUG=b:287379760
BRANCH=firmware-nissa-15217.B
TEST=boot to ChromeOS, cold reboot/suspend/recovery mode/install OS
work normally.
Change-Id: I8a1ac60f599f2895654946d9fa1c4e1f2657fd10
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1) LP5 Memory - 2GB Micron MT62F512M32D2DR-031 WT:B
2) LP5 Memory - 2GB Hynix H9JCNNNBK3MLYR-N6E
3) LP5 Memory - 4GB Samsung K3LKBKB0BM-MGCP
4) LP5 Memory - 4GB Hynix H9JCNNNCP3MLYR-N6E
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H9JCNNNBK3MLYR-N6E 0 (0000)
K3LKBKB0BM-MGCP 1 (0001)
H9JCNNNCP3MLYR-N6E 2 (0010)
BUG=b:292461498
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I02e49d60e43c4fed8356556ec194d726c30cd609
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The patch disables PCH USB2 Phy power gating to fix display flicker
BUG=b:292403156
TEST=Verified on the defeat board
Change-Id: If0c0e655c5d32f39b90635bb3c1d13d8b6993b59
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update Touchscreen GPIO to use the correct GPIO 90. GPIO 32 was a
copy/paste from dalboz and corresponds to the FP PWR EN on trembyle
platforms.
BUG=b:292656388
TEST=build/boot morphius
Change-Id: Ia6cdbe9195535093e68dbafedaddb70aaf73da88
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76747
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the cs_pi_start_high_in_ect if the DUT is using one of the two
following Hynix parts: H54G56CYRBX247 and H54G46CYRBX267. Failure to
set cs_pi_start_high_in_ect when using these parts will result in an
MRC cache failure and DUT will fail to boot.
BUG=b:292153199
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot brya
variant to kernel.
Change-Id: I36040139b959c85c3ac220a34574caa12ca6c5fe
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
With currently set default PSP_SOFTFUSE_BITS for phoenix SoC,
the non-serial build does not boot on Myst.
Override PSP_SOFTFUSE_BITS by disabling SPIConfig to also get
the non-serial build booting.
The documentation of PSP_SOFTFUSE_BITS is available in #55758 doc (NDA).
BUG=b:292489356
TEST=Flash image-myst.bin, verify that it's able to boot on Myst
proto0.
Change-Id: Id4472fd85fdefcafb8378199dbaa054fab8b3274
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76713
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: Ica3756e117fc58166958f37e7b007abb79d9d350
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76744
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: Ie1d882cac90211541a636d2dab297c343a12d66d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76743
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Necessary to allow coolstar's Windows touchpad driver for this board,
since the touchpad is attached to the SMBus. The VID/DID combo used is
not registered/doesn't conflict with any currently in use, and would
be difficult to change at this point since the Windows drivers have
already been signed.
TEST=build/boot Win11, Linux on butterfly/lumpy/parrot, verify
touchpad driver works properly.
Change-Id: I61912fd6db9eb4b8d202ab633b8c7ca5913e759f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for redrix board. Please refer Intel doc#723158 for
more information.
BUG=b:292435264
TEST=build and boot redrix
Change-Id: I34d10c763f4710d2c5678704320fd1cc8d8b6287
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76670
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Camera LED will blink several times as sensor is being probed during
kernel boot.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:292173903
TEST=Build and boot on Yavilly EVT unit. Verify & observe Camera LED
blinking behavior.
Change-Id: Ic3e3439dc9313325189761b277e1a3bd1c1d9418
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76671
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These boards do not actually support RTD3. The power GPIOs for
components are connected to 3.3V and the reset GPIO is connected to
`PLT_RST#`.
Change-Id: Id5e318c388f669d6b2935dc98ae29485955e6e72
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
After switching to S3, it was found that drives on the SATA port do not
exit D3cold on S3 exit. Disable RTD3 on the port until the issue can be
resolved.
Avoids the following error in Linux:
pcieport 0000:00:1d.0: Unable to change power state from D3cold to D0, device inaccessible
Tested on darp8 with a Samsung 970 EVO or Crucial P5 in J_SSD1.
Change-Id: Ib26f59db61acfbf9248cea379c197765d3d9c470
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76593
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Lemur Pro 12 (lemp12) is a Raptor Lake-U board.
Tested with a custom edk2 UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- DIMM slot with 4800 MT/s memory
- Both SSD slots
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone + mic audio
- 3.5mm microphone input
- S3 suspend/resume
- TPM 2.0 device
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
Not working:
- Onboard RAM
Change-Id: I0c4941534b719ea8fc93eb3492d5fe16db208647
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Bonobo Workstation 15 (bonw15) is a Raptor Lake-HX board.
Tested with a custom edk2 UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots with 5200 MT/s memory
- All M.2 SSD slots
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone + mic audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
- TPM 2.0 device
Not working:
- Discrete/Hybrid graphics
- Thunderbolt
Change-Id: I6d4e408604a0c5c5272e841f4093baaf28c790cd
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add bank locator and slot existance to the mainboard code.
TEST: Verified on Linux that all slots show in dmidecode -t 17.
Change-Id: I4ced36e26368d3f99a7341cb55a8deb118b2d1a4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The SuperIO is not used so don't enable decoding of 0xE2 and
drop all code using it. It's not even required for the virtual
UART on 0x3f8 to work.
Add the virtual UART on 0x3f8 as ACPI device.
TEST: Verified on SBP1 that serial still works.
Change-Id: I8e431a0c8417435cc6e3ba16f97ff080e1656a7b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add pujjo new supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. Hynix H58G56BK7BX068
2. Samsung K3KL6L60GM-MGCT, K3KL8L80CM-MGCT
3. Micron MT62F1G32D2DS-026 WT:B
BUG=b:292452868
TEST=Use part_id_gen to generate related settings
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ia123a1cfd93a5e08ab0ba65f1d9be240d60ff356
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76672
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a new variant screebo4es.
The new variant will support only ESx samples. The existing rex
variant will support the QS samples.
BUG=b:292280656
TEST=Able to build google/screebo4es board and boot on target
hardware.
Change-Id: If77b4a773bee3633008d39c1886b61869c9618de
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=b:290894460
TEST=`emerge-rex coreboot chromeos-bootimage`
then check variant name with image*.bin.
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I8f739485dbaab074f57eaa4dacc9f228a3f4aa14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76667
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the APOB cache for only Myst, and re-enable APOB for other
Phoenix SOC mainboards.
BUG=b:290763369
TEST=verify APOB cache is disabled
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ie611e0b84611b2f50c989c75612fc2186b2dbfdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76567
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Mapping to the fw_config of AUDIO_AMP in dedede,
and set new AUDIO_AMP configuration of ALC5650 as value 4.
BUG=b:284060672
BRANCH=dedede
TEST=build pass
Change-Id: Ic3dccd09d3ba1619cce2ac0d5f123badbeeaccdc
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch increases the `tcc_offset` to reduce the TCC
(Thermal Control Circuit) activation temperature to avoid running
into abrupt power off during power cycle tests.
On Intel processors, the core frequency can be by an HW agent when
the current temperature reaches the TCC activation temperature.
The default TCC activation temperature is specified by MSR_IA32_TEMPERATURE_TARGET (which is 90°C for google/rex variants).
However, this patch adjusted the TCC by specifying an offset in
degrees C (i.e., using `tcc_offset` from variant override device tree).
Note: The bigger the TCC offset is, the lower the effective TCC activation temperature would be, to ensure that processors can be throttled earlier before the system critical overheats.
BUG=b:283008762
TEST=Able to perform power cycle on google/screebo w/o any crash/shutdown.
Change-Id: Ib19703877dbbfc26b2d9f538dda4f10c27cf872d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76658
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Adding EC_HOST_EVENT_PANIC to SCI mask allows the EC to interrupt the
Kernel when an EC panic occurs. If system safe mode is also enabled
on the EC, the kernel will have a short period to extract and save info
about the EC panic.
BUG=b:290985698
BRANCH=firmware-volteer-13672.B
TEST=Observe kernel ec panic handler run when ec panics
Change-Id: I87173f93d0e47baa816d15dad0777007342b4fdb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Choose BOARD_GOOGLE_MODEL_REX while setting up the default config value
for variants created using google/rex model.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I107f4e375b5c9e9c0fb80c4d396164c10c1fc1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch creates a new variant rex4es. The new variant will support ESx samples. The existing rex variant will support the QS samples.
BUG=b:290732344
TEST=Able to build google/rex4es board and boot on target hardware.
Change-Id: I25dd1f42ee812f47289da0c2ef7aa79d6f340d48
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch creates a rex model so that other variants developed using
`rex` baseboard are easy to land without duplicating the config
selection.
So far, `rex0` and `rex_ec_ish` are developed using the `rex` model.
The plan is to extend the support for `rex4es` and `rex4es_ec_ish`
variants.
TEST=Able to build and boot google/rex.
Change-Id: Id4e8d1162da93b7266ee1108f870e89b6d884ab9
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76608
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow baseboard Rex to make GPIO changes
BUG=b:286187821
TEST=Ability to enable and disable WIFI function in OS.
Change-Id: I805ce859c42c7c0a9d117418a80555658f844e09
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76551
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
This supports a brand new I2C driver that is designed specifically
for the Pixel 2013 chromebook (LINK). The GMBus interface on the IGPU
is an i2c-compatible interface, but AFAIK only Link has touch devices
attached in this way.
On Windows, the PCIe device for the IGP is owned by the Intel
proprietary driver, hence a separate ACPI device has to be added for
the I2C driver arbitrator to attach to. The MMIO method is used instead
of _CRS so that Windows does not try to assign ownership of the
resource to our device (even though we're using the MMIO registers at
the same time as the IGP driver).
Even though in theory 2 drivers accessing the same MMIO may cause
problems, in testing, there has been no issues with
sleep/wake/hibernate, updating/installing/uninstalling the IGP driver,
or changing display resolutions with the i2c driver attached.
The arbitrator is necessary as well, since even though there are
multiple i2c buses, the MMIO registers are shared. Hence a shared lock
is required for i2c access across the buses.
The original Sleep Button devices are preserved for Linux due to the
completely custom and non-standard implementation of the Windows driver
in order to work around the non-standard nature of Link's hardware.
Change-Id: If7ee05d15bc17d335cf8c1a8e80bea62800de475
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
CPU:
- 2 SPR sockets
- 64 total PCIe 5.0 lanes with up to 64 lanes of Flex Bus/CXL per CPU
- Up to 32 DDR5 DIMM
- 1 Gbase-T NIC port
- 1 USB3.0 type A, 1 USB2.0 connector
- 1 VGA connector
BMC:
- ASPEED AST2600 BMC
- 1 DDR4 8Gb memory
- 1 8GB eMMC
Test:
The board boots to Linux 4.19.6 with all 192 cores available.
Change-Id: Ic9d99c3aadaa9f69e6d14d4b1a6c5157f5590684
Signed-off-by: Annie Chen <Chen.AnnieET@inventec.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Wei Chen <Chen.HW@inventec.com>
Reviewed-by: Annie Chen <chen.annieet@inventec.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In order to reduce S0ix resume time, decrease stop_delay_ms from
300ms to 200ms for Goodix GT7996F. The value source is from
https://partnerissuetracker.corp.google.com/issues/285999032#comment16.
BUG=b:285999032
BRANCH=firmware-nissa-15217.B
TEST=boot uldren to ChromeOS and touchscreen is workable.
Change-Id: I2f0adadbd3d0774da03338cc0abd1639104876d9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76577
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
There is a problem of screen shake on the old panel[1]. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code is
mainly adjusted for GOP timing. When Display sleep in, raise all GOP
signals to VGHO and then drop to GND. In order to be consistent with
the current panel model, let's rename this file.
[1]: INX old panel product number is HJ110IZ-01A-B1, and the new
panel product number is HJ110IZ-01A-B2. We have recalled the shipment
old panel.
BUG=b:270276344
BRANCH=trogdor
TEST= test firmware display pass
Change-Id: I2b2534afee1ed700c39d3c360aafd685b63ccbfb
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch updates the Type-C USB2/3 port mapping to reflect the mux
connection change as mentioned in previous patch
commit ee3f796200bf3baf8a1906 (mb/google/rex/var/ovis: Fix mux
change as per schematics).
Here is the correct port mapping after considering the mux swap:
+--------------------------------+-------------+---------------+
| TCSS-USB Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 3 | 1 |
| USB3-Port | 0 | 2 | 1 |
+------------------+-------------+-------------+---------------+
BUG=b:289300284
TEST=Able to build and boot google/ovis to get display over Type-C1
and Type-C2 port.
Change-Id: I460004842dd8fcdc03fca6639d03e422259380ca
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76464
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change SD_CLKREQ_ODL from GPP_D19 to GPP_D18
BUG=b:291051683
BRANCH=none
TEST=emerge-rex coreboot
Change-Id: Ic102e42482328580c5334e6ff036b774f5002e00
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76565
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
According to Intel doc#763797 to overcome early command training hang
issue, the CsPiStartHighinEct needs to be enabled for hynix memory.
BUG=b:284192689
BRANCH=firmware-brya-14505.B
TEST=Built and booted into OS.
Change-Id: Ic177c5ffcb6a3d3f76292a0d99ab0e806d43fc11
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76549
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable CsPiStartHighinEct to fix MRC Cache fail issue
BUG=b:279835630
BRANCH=none
TEST=Pass MRC Cache test with toolkit 1000 times
Change-Id: I25cd856785bab9c661e30e2987b43f0dc2ba9564
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
