| Age | Commit message (Collapse) | Author |
|---|
|
Configure GPIOs according to schematics revision 20230923.
TEST=emerge-brya coreboot
Change-Id: I10bd1b72c9b0299b8d29ab642fddb5f0c4727652
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Some Type-C monitors do not immediately assert HPD. If we enter FSP-S
before HDP is asserted, display initialisation may fail. So wait for
HPD.
This is similar to commit b40c6009141e ("mainboard/hatch: Fix puff DP
output on cold boots") on puff, except we don't use
google_chromeec_wait_for_displayport() since that EC command was removed
for TCPMv2 (https://crrev.com/c/4221975). Instead we use the HPD signals
only. By waiting for any HPD signal (Type-C or HDMI), we skip waiting if
HDMI is connected, which is the same behaviour as puff and fizz.
TEST=On dibbi, connect a display via a Type-C to HDMI dongle and check
the dev and recovery screens are now displayed correctly. Also check the
logs in the following cases:
Cold reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 800 ms
Warm reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct Type-C:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct HDMI:
HPD ready after 0 ms
Cold/warm reboot in dev mode, no display:
HPD not ready after 3000 ms. Abort.
Change-Id: Id4657b5d5a95a68ecbd9efcf3585cf96ad1e13e1
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
update DTT settings for thermal control, as follows:
1.Cancel TCPU trip point and fine tune other protection temperature on the Critical policy table
2.Fine tune EC/Bios protection temperature
BUG=b:291217859
TEST=emerge-rex coreboot
Change-Id: I0e2ff6eea9fed71ad7680c1fac4921984b87aca5
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78290
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: zhongtian wu <wuzhongtian@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Internal testing showed that CPU heatsink gets hot and temperature
goes over 75C. In this situation, the fan does not even start
to lower down CPU temperature. This is because of existing temperature
thresholds of TSR0 and TSR1 sensors are set at 45C to start fan.
With updated new settings based on tuning from thermal team,
the fan starts early at 43C for TSR0 and TSR1 so the CPU temperature
stays below 75C.
BUG=b:302673874
TEST=Built and tested on google/rex board
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I6580652d6165946e98ecf1b46ace3352cd34dcdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Create the dexi variant of the taranza project by
copying the files to a new directory named for the variant.
BUG=b:303533815
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DEXI
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I708a16cb864dca7309cb0201e7887af7456a4885
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78249
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=b:303533832
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I575da55b96bf4deacec5c0992eae9930eb0745d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Measured the I2C frequency meets spec
- I2C0 (TPM): 949.7 Khz
- I2C1 (TouchScreen): 395.8 Khz
- I2C3 (Audio): 387.4 Khz
- I2C5 (Touchpad): 384.8 Khz
BUG=b:303356736
TEST=USE="project_joxer emerge-nissa coreboot"
and check all I2C devices measurement result
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I17dd1cb7800d00669f86fc6e2b350757695da881
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78218
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Package C-state auto demotion feature allows hardware to determine lower
C-state as per platform policy. Since platform sets performance policy
to balanced from hardware, auto demotion can be disabled without
performance impact.
Also, disabling this feature results soc to enter below PC8 state and
additional power savings ~30mW in Local-Video-Playback scenario.
BUG=b:303546334
TEST=Local build successfully & Boot to OS successfully
- Also check platform enter PC8 state in local video playback
- before this change: # iotools rdmsr 0 0xE2 -> 0x0000000060008008
- After # iotools rdmsr 0 0xE2 -> 0x0000000000008008
Change-Id: Ia4cf4a7cb6bd5eaae26197b55f9385c078960d7b
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78250
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Based on the power sequence of the panel [1], the power on T3 sequence
VSN to RESET should be larger than 1ms. Because the Power IC descending
slope takes 2ms, actual measurement needs 3ms to meet the timing of
panel sequence.
[1] HX83102-J02_Datasheet_v03.pdf
BUG=b:302212730
BRANCH=corsola
TEST=emerge-staryu coreboot chromeos-bootimage and boot the panel
Change-Id: I488c746d1fcfc165125b0ecccb0bccbb99231b00
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78185
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Quandiso reserve bit 11 for mipi camera usage.
BUG=b:300574047
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id4343083f0d69a49c642657d165ceac349cd7422
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78213
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:300573763
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Iff8167695c302f7b58976516d651a81f1a429bee
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
When service center repair touchscreen or touchpad will change
compatible device not specific one, the fw_config probe mechanism is not
convenient for service center. Removing touchscreen and touchpad
fw_config probe for the purpose.
BUG=b:297840605
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I66f12ae478f74c019c53ee5e77f7e0f9c324e758
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77538
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn off GPP_H13 (EN_PP3300_SD_X) in s0ix for power saving. It reduces
about 3mW of power consumption in s0ix on pirrha proto board.
BUG=b:300845527
TEST=Built and verified GPP_H13 voltage was 0V in s0ix.
Also verified SD card worked after s0ix for 20 times.
Change-Id: I5ec53820276e50f5b8b01584595118cf2dc4c95c
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch reverses ISH UART pin configuration to allow ISH to enter
into suspend mode. This UART port is for debugging purposes.
BUG=b:302612549
TEST=On Google/rex platform with ISH enabled, do suspend_stress_test
This test must pass
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I8aba45420744a3990e1f9637c3b31ea2e0f78f87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78049
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for
enable USB wake.
BUG=b:302230434
TEST=Verify USB-A device could wake up Boxy
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I0f6300dc6bbb6fb8226151e49e38f0450b1e71b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78144
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for enable USB wake.
The physical USB slot is 6, USB2 port5 for Bluetooth, total USB2 port num is 7, USB3 keep 6.
BUG=b:300844110
TEST=Verify USB-A device could wake up Taranza
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ied92c4a70bc594bd189dcb942f1a445412509464
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78068
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
This panel is never actually enabled on Geralt. The derived project
won't use this panel either. Therefore, remove this panel support.
BUG=none
BRANCH=none
TEST=emerge-geralt coreboot
Change-Id: I97ed5b341724ed42098b2c17d0eb75eab881dbb1
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The tolerance of ADC voltage table is too small. Update the table values
accordring to the suggestion from the hardware team. The patch is
prepared for the derived projects. There is no actual issue now.
BRANCH=none
BUG=b:301908091
TEST=check firmware screen
Change-Id: I3bde30b6bbe79c81e276f23f4110715c3278d42c
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add VCM power control to configure 2.8V and reset pin, and VCM can
be powered on/off properly.
BUG=b:292907385
TEST=Run ITS test
Change-Id: I242025836fd50076a40ffcc4e5d4a5d5bc6fb4d0
Signed-off-by: Serin Yeh <serin.yeh@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78170
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPL_TABLE_FILE and SPL_RW_AB_TABLE_FILE Kconfig options provide a
way to override the default SPL file configured in the SoC's fw.cfg file
by passing the '--spl-table' parameter to amdfwtool which will then use
the override instead of the SPL file from the fw.cfg file. When
SPL*_TABLE_FILE is an empty string, the corresponding add_opt_prefix
call in the makefile will result in no '--spl-table' parameter being
passed to amdfwtool, so it'll use the default SPL file from fw.cfg. In
order to not pass an SPL override by default, remove the default from
the SPL_TABLE_FILE in the SoC's Kconfig. The SoC default pointed to the
same SPL file as in fw.cfg file anyway. Now only when a mainboard sets
this option to point to a file, that file will be used as an override.
This override is used to include a special SPL file needed for the
verstage on PSP case on the Chromebooks. Since SPL_TABLE_FILE is an
empty string by default, neither the SPL_TABLE_FILE Kconfig option nor
it being evaluated in the Makefile need to be guarded by HAVE_SPL_FILE,
so remove the dependency in the Kconfig and the ifeq in the Makefile.
Before this patch, the HAVE_SPL_FILE option controlled two things that
shouldn't be controlled by the same Kconfig option: Only when
HAVE_SPL_FILE was set to y, the SPL_TABLE_FILE override was taken into
account, and it also controls if spl_fuse.c got added to the build which
when added will send the SPL fusing command to the PSP. So the case of
needing an SPL file override, but not updating the SPL fuses wasn't
supported before.
The SPL file in the amdfw part will be used by the PSP bootloader for
the anti-rollback feature which makes sure that the SPL file version
isn't lower than what is in the SPL fuses. For this the SPL file needs
to be present in the PSP directory table. The SPL version check happens
way before we're running code on the x86 cores. The SPL fusing PSP
command that can be sent by coreboot will tell the PSP to update the SPL
fuses so that the fused minimal SPL version will be updated to the
current SPL version.
Since the former HAVE_SPL_FILE option now only controls if the SPL
fusing command will be sent to the PSP mailbox, rename it to
PERFORM_SPL_FUSING to clarify what this will do and update the help text
correctly describe what this does.
TEST=With INCLUDE_CONFIG_FILE set to n, timeless builds for both Birman
with Phoenix APU and Skyrim result in identical binaries.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6cec1f1b285fe48e81a961414fbc9978fa1003cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78178
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add probe fw_config to USB C1/A0 port on daught_board for DB_1A sku.
BUG=b:294456574
TEST=emerge-nissa coreboot
Change-Id: I2261b0e4d2b673b6186a435cce8dc6a4ccacb0a7
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I1439f785cb9ceeefab9d24caa88e35bd43f68315
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I5527d5968be35f52b912d9d6e1d9f46f24569bbc
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
During suspend, the ISH I2C transactions cannot go through
because the GPIO pads remain the pervious value.
The IO Standby State (IOSSTATE) needs to be changed to keep I2C bus
active and functional during suspend.
BUG=b:302612549
TEST=on Google/rex platform with ISH enabled, do suspend_stress_test
and check that no i2c failure.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I9a2c902ed56461f3a535428db399c2050756f2da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78179
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set default to enabled for hibernate on setup failure for all devices
using a Google EC. This will have no impact on devices that don't
bring the GSC down on hibernate, but will provide a recovery path
for all devices that do.
BUG=b:296439237
TEST=Force error on Skyrim with custom build, boot normally with
normal build
Change-Id: I2d9e8f75b25fb6c530a333024c342bea871eb85d
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78098
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BOARD_SPECIFIC_OPTIONS is duplicate to BOARD_GOOGLE_CORSOLA_COMMON.
Thus, move all selects to the latter option.
Change-Id: I498c6671b2dfc72820fc522744af7ce3b0a62930
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
ASPM on the WLAN PCIe bus introduces large latency spikes, which can be
measured with cyclictest:
$ cyclictest --policy=rr --priority=12 --interval=10000 --threads=1 --loops=6000
Disabling ASPM for WLAN reduces the latency spikes from 2,500-3,000 usec
down to 35-65 usec. These latency spikes can impact the user when
real-time processes like Audio (cras) are starved of CPU time, leading
to buffer underruns resulting in crackling/distorted audio.
ASPM is already disabled for Nipperkin devices (CB:63537), so this CL
disables it for both in the shared declaration of
guybrush_czn_dxio_descriptors.
Power impact for Dewatt:
* ASPM enabled
power_VideoCall.FDO_25min_webrtc
w_energy_rate 7.425043688811071
power_Idle.default20min
wh_energy_used 1.4164200000000022
* ASPM disabled
power_VideoCall.FDO_25min_webrtc
w_energy_rate 8.779998551703423
power_Idle.default20min
wh_energy_used 1.4860800000000012
When using Google Meet over WiFi, power increases by ~1.5W.
BUG=b:297970318
TEST=cyclictest --policy=rr --priority=12 --interval=10000 --threads=1 --loops=6000
Change-Id: I16940987d598943bd5d6ace8b4008eba4d4a177c
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77963
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Implement support for elan i2c touchscreen and use fw_config
to pick between i2c or HID-over-i2c touchscreen.
Support G2 TS have different slave address by fw_config
BUG=b:295272539
BRANCH=firmware-nissa-15217.B
TEST=build and verified touchscreen work
Change-Id: I5e3f85106606d84e1cfa204e62b7b2662db6546b
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Enable hibernate on TPM setup error for Skyrim devices.
BUG=b:296439237
TEST=Force the error by hard coding the return code and observe the
device entering hibernate.
BRANCH=None
Change-Id: Ibf96b830f07dac98035d3152c8ec220685a912bc
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77668
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert TPM functions to return TPM error codes(referred to as
tpm_result_t) values to match the TCG standard.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: Ifdf9ff6c2a1f9b938dbb04d245799391115eb6b1
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77666
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert hex print values to use the %#x qualifier to print 0x{value}.
BUG=b:296439237
TEST=build and boot to Skyrim
BRANCH=None
Change-Id: I0d1ac4b920530635fb758c5165a6a99c11b414c8
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78183
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure PL1 and PL2 are configured for powerformance.
Based on values from Intel Meteor Lake UH Power Map document ID:640982
BUG=b:286834207
TEST=Build and boot google/ovis and check ACPI SSDT for DPTF entries
Change-Id: Ia40884b3abd1417dea6ad291de4845762ee01966
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77623
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify the settings:
1)Add fw_config probe on USB type C for "DB_1C_LTE".
2)Add fw_config probe on USB type A for "DB_1A_HDMI".
BUG=b:296791122
TEST=build and check USB functions on craask
Change-Id: I2775098ab380995e62f264bc51a430762c256c4b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78169
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rather than disabling C State demotions for every single Raptor
Lake board due to an issue with S0ix, regardless of if they even
use S0ix, configure it in the mainboard.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4f941a549bc717ae2f8ec961ead7ac7668347c99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Configure the rcomp, dqs and dq tables based on the schematic.
BUG=b:298337185
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=dochi emerge-brya coreboot
Change-Id: I182e287423e6f784712c5004a6fe2d12a5b36190
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add PLx from JSL PDG (ID: 613095) in taranza devicetree.
Add ramstage.c in Makefile.inc and update Taranza power limits in
taranza ramstage.c.
BUG=b:296004956
TEST=emerge-dedede coreboot and check psys and PLx value on taranza
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Id43bb91bc9efb91cb074b075122cce4f22e0716c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Configure I2C5 timing in devicetree to ensure I2C devices
meet timing requirement.
BUG=b:300177424
TEST=Build and check I2C devices timing meet spec.
| | I2C5-Before | I2C5-After |
|-------------|-------------|------------|
| FSMB(KHz) | 445.400 | 343.638 |
| TLOW(us) | 1.543 | 2.068 |
| THIGH(us) | 0.475 | 0.604 |
| THD:STA(us) | 0.603 | 0.711 |
| TSU:STA(us) | 0.612 | 0.611 |
| TSU:STO(us) | 0.605 | 0.611 |
| TBUF(us) | >1.914 | >2.044 |
Change-Id: I3bb678b66d55c6bfaff76e3e5500a2a3bc3a2c61
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78111
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add 4th sensor device for DTT tuning.
BUG=b:292134655
TEST=Built and verified DTT tool could monitor the new sensor device
Change-Id: I62f50711af81dfc1566d655f6dcfc66f68dbc794
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
|
|
BOARD_SPECIFIC_OPTIONS is duplicate to BOARD_GOOGLE_OAK_COMMON.
Thus, move all selects to the latter option.
Change-Id: Id80b8a9bcad9337c8aa76fa6e5d2c9752b8021b7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
BOARD_SPECIFIC_OPTIONS is duplicate to BOARD_GOOGLE_BASEBOARD_GUYBRUSH.
Thus, move all selects to the latter option.
Change-Id: I570c3cfd3d100ad90e35ec5d89686cb6a4bd8e82
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Facilitates correct profile selection by SOF Windows drivers.
Profiles for nokris and quandiso will be added once correct board
configs can be determined.
TEST=build/boot Win11 on google/craask, verify correct audio profiles
loaded, audio functional.
Change-Id: Id4582b5dd74a4905ea509813ec99663577360095
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
|
|
Add Makefile.inc to include five generic LPDDR5 SPDs for the following
parts for Dochi:
DRAM Part Name ID to assign
MT62F1G32D2DS-023 WT:B 0 (0000)
K3KL8L80CM-MGCT 1 (0001)
H58G56BK8BX068 0 (0000)
BUG=b:298337185
TEST=USE="project_dochi emerge-brya coreboot"
Change-Id: If0fd4bc950cef484db53b7b21849cfdfdd7816a5
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Instead of selecting board-specific options under the common option and
making them conditional, move them to their related board option.
Change-Id: If9bea61cb84590e7455add908fa7722c60444503
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The tolerance of LCM voltage table is too small which leads to wrong
panel ID detection. Fine tune LCM ADC voltages based on hardware
calculations.
BUG=b:300418909
TEST=FW screen display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Id8dec043584f4c552837f70adb491584bfda7acf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
BOARD_SPECIFIC_OPTIONS is duplicate to BOARD_GOOGLE_CHERRY_COMMON.
Thus, move all selects to the latter option.
Change-Id: I080201761d0a06d3b8a5a29de6085dde58960a60
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75085
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BOARD_SPECIFIC_OPTIONS is duplicate to BOARD_GOOGLE_ASURADA_COMMON.
Thus, move all selects to the latter option.
Change-Id: Id80523dce70f13f64a49b71656276c51e80ae5cd
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75084
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id69ea99b452e4214fcc81335a5c961b4da3ce48b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id85503a5ec970ea92c07b99ec7048c521d85c79b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75026
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id450a4b6e409a548ee4d79b8b2ebf30ef61a3e27
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78083
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No Windows driver exists or is needed, so hide to prevent an unknown
device from being listed in Windows Device Manager.
TEST=build/boot Win11 on frostflow, verify unknown device for the
fingerprint reader no longer present.
Change-Id: I666e92706f698608f2df92c8296cfb615d5ece67
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
No Windows driver exists or is needed, so hide to prevent an unknown
device from being listed in Windows Device Manager.
TEST=build/boot Win11 on dewatt, verify unknown device for the ACP
machine driver no longer present.
Change-Id: I44d25fd2ea75593383cbb14f2324d4376b399de7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
No Windows driver exists or is needed, so hide to prevent an unknown
device from being listed in Windows Device Manager.
TEST=build/boot Win11 on morphius, verify unknown device for the ACP
machine driver no longer present.
Change-Id: I14347ab6c840066db4ff700eff1aad4cf6faf66b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
1. Support world facing usb camera on usb2_port7.
2. Update MB/DB fw_config to distinguish LTE and non-LTE devices.
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I0c508475fdc86f0d7357f19684bdaae06e77fc27
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77398
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- GPIO changes:
GPP_B5 ==> I2C_P_SENSOR_SDA
GPP_B6 ==> I2C_P_SENSOR_SCL
GPP_H19 ==> P_SENSOR_INT_L
- I2C SX9324 support
- Disable GPIOs when sub board LTE not used
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5ed82b125b6c594225efca418017ef42f4f63b9d
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
GPIO changes
- GPP_D8 ==> SD_CLKREQ_ODL
- GPP_D17 ==> SD_WAKE_N
- GPP_H12 ==> SD_PERST_L
- GPP_H13 ==> EN_PP3300_SD_X
Genesys Logic GL9750 support
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib7c80f43680481c0d1a18662fa494012390a984d
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77391
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Quandiso doesn't support mipi WCAM.
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I8a166d0bb1c034f2e3a5af7456500abd078e93f9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77389
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update files copied from yavilla
- fw_config setting
- GPIO setting
- Kconfig setting
- overridetree setting
- SPD memory parts
- variant setting
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
flash bin file in DUT
Change-Id: Ibbef42a1f891d0cf0309aa76edd7ec5dd664588e
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77361
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Dedede boards which select AUDIO_AMP_UNPROVISIONED via fw_config use
rt1015 for the speaker topology, not max98360a.
TEST=build/boot Win11 on google/magpie, verify correct audio profile
selected.
Change-Id: I5b75bd8fd37d2837de3c5bd25a02411a6982103b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add data.vbt file and Kconfig to use it.
Extracted from google firmware genesis_13324.283.0
TEST=build genesis with FSP GOP display init
Change-Id: If836b214da1350111d7b7d1f24865199f814c521
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add data.vbt file and Kconfig to use it.
Extracted from google firmware ambassador_13324.283.0
TEST=build ambassador with FSP GOP display init.
Change-Id: I5c47700c5abe7d96112702d48a2b749f1784a494
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78032
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Without the PCH UART GPIOs set early, there is no serial console
output until ramstage. Add them to the early GPIOs for all puff
variants.
TEST=build/boot google/puff (wyvern) with serial console enabled,
verify console output starts in bootblock.
Change-Id: Ica0506b2b80e4fac0d3ca11b4cfdd128ce424b36
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78029
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Brya queries the TPM in early ramstage (pre-device init) to determine
if the CR50 has support for long-pulse interrupts. If the TPM (and
underlying I2C controller) hasn't already been setup in verstage, it
will fail to do so in ramstage since the I2C controller has not yet
been initialized. To work around this, initialize the TPM in bootblock
for the non-vboot case, to ensure the I2C controller is set up when
needed in early ramstage.
TEST=build/boot google/brya (banshee), verify no I2C errors in cbmem
console when initializing TPM in early ramstage.
Change-Id: I26f0711a9cc4c2eb9837f258cadf391d337994c9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78028
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds ACPI entries for SAR Proximity Sensors as below
SAR1 Sensor:
- SAR1_INT_L : GPP_E00
- I2C5 7-bit address 0x28
SAR2 Sensor:
- SAR2_INT_L : GPP_E08
- I2C 7-bit address 0x2c
BUG=b:297977526
TEST=Able to build and boot google/rex.
w/o this patch:
Total 6 devices are listed below:
> ls -lt /sys/bus/iio/devices/iio:device*
/sys/bus/iio/devices/iio:device5 -> ../../../devices/LNXSYSTM:00/
LNXSYBUS:00/PNP0A08:00/device:07/
/sys/bus/iio/devices/iio:device0 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device2 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device4 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device1 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device3 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
w/ this patch:
Total 8 devices are listed below:
> ls -lt /sys/bus/iio/devices/iio:device*
/sys/bus/iio/devices/iio:device6 -> ../../../devices/pci0000:00/
0000:00:19.1/i2c_designware.4/i2c-
/sys/bus/iio/devices/iio:device5 -> ../../../devices/LNXSYSTM:00/
LNXSYBUS:00/PNP0A08:00/device:07/
/sys/bus/iio/devices/iio:device7 -> ../../../devices/pci0000:00/
0000:00:19.1/i2c_designware.4/i2c-
/sys/bus/iio/devices/iio:device0 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device2 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device4 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device1 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
/sys/bus/iio/devices/iio:device3 -> ../../../devices/pci0000:00/
0000:00:1f.0/PNP0C09:00/GOOG0004:0
Change-Id: I0a518d58915f9f4dbe58a45c4dc5875abbfda135
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78045
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Intel Meteor Lake QS silicon provides better size optimized pre-x86
reset blobs.
This patch creates a new flash layout (FMD) for QS to accommodate those
optimizations, and renames the existing FMD for ES (pre-prod) silicon.
Comparative analysis between QS and ES flash layout is here:
For QS silicon:
- SI_ALL reduced from 9MB to 8MB.
- SI_BIOS increased by 1MB (from 23MB to 24MB) to fill in the 32MB SPI
layout.
- ME_RW_A/B reduce from ~4.5MB to 4MB.
- Ensure RW-B slot is starting at 16MB boundary.
- Unused space increased by 1MB.
For ES silicon:
- SI_ALL: 9MB
- SI_BIOS: 23MB
- ME_RWA/B: 4.5MB (for ISH) and 4.4MB (non-ISH).
- Unused space 3MB (for release) and 2MB (for debug) layout.
Change-Id: I881832a6b11a35710d4e847feadcc544b1f5d048
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77994
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I590b7fb5f5f52cbf1a61c65f8fac757e36feac5e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75028
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I866333a234203dc2da3d4dd8c4f87e4cfa332787
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Ia4ed3491e6a32659b957285ab20ad47c9085083c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75025
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I097d50a7af7c8ea48369806e8bb73734a8e84470
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75024
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id7f9b598cc9df51ddf664b851172cc96a710c580
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75023
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I3f4965b8b253983ad1f8db77e1b91860a270c305
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: If2c9c52f1e2866082df8e534b1a074639bb62db2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75020
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Idf4a566af3853636945709c88c03fb8e777211c2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Iaa73bf7f85f840299c467b7d712546d3f72a4e75
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id1b0d375670f9e59047eff737bc17e61bf93175e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75016
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I1033a974a818308b31e1334cad5869d2cd81bd9e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75017
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I207e25059a9fb9e6a951018e954662931b3f8b93
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75018
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Id060f781b87567da2756c89275002b9ea4f4976c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75015
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No drivers exists or are needed, so use devicetree hidden keyword to
set the ACPI status to hidden to prevent unknown devices from showing
in Windows Device Manager.
TEST=build/boot Win11 on morphius, verify unknown devices for the
fingerprint reader and stylus detection are no longer shown.
Change-Id: I992c0ec8d97c6041e3a268445613bfa42dd8b279
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable wake-on-DP by adding USB mux events to the wake mask. The EC
wakes the AP with these events for DP connect/disconnect.
BUG=b:294307786
TEST=DP connect/disconnect wakes the DUT appropriately.
Change-Id: I864b03d08ce3d756bf4987d886db621d937483ce
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78034
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Karis uses PIXA touchpad, update related settings.
BUG=b:294155897
TEST=(1) emerge-rex coreboot
(2) Test on karis, touchpad function works
Change-Id: I26e3257485c4abe050de7a79c6d3b72dbd048710
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77517
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
BUG=b:299374763
TEST=emerge-rex coreboot
Change-Id: I40fc768522e8679337c3b9f5497278e9f4639c3e
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77888
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures that the
`DRIVERS_INTEL_MIPI_SUPPORTS_PRE_PRODUCTION_SOC` config is enabled if
the underlying platform is built with a pre-production SoC (aka
`SOC_INTEL_METEORLAKE_PRE_PRODUCTION_SILICON` config is enabled).
BUG=b:300652989
TEST=Ensures `DRIVERS_INTEL_MIPI_SUPPORTS_PRE_PRODUCTION_SOC` is enabled
for google/rex4es aka all variants with ES silicon.
Change-Id: Ieda39427915fa3973b832376ec20fc414ac2bedd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77993
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
The tree contains engineering sample boards, that ship with
pre-production Meteor Lake SoC. These boards are not sold.
BUG=b:300652989
TEST=Ensure mainboards like google/rex4es and screebo4es have
`SOC_INTEL_METEORLAKE_PRE_PRODUCTION_SILICON` config enabled.
Change-Id: I1a875a0f1d2c38582f35250ebe645e53599f62de
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77992
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Add the eMMC MMIO device to the devicetree and make it use the common
AMD eMMC driver. Since there is now a device for this in the devicetree,
also use this device to determine if the FSP should be told if the eMMC
controller is supposed to be disabled.
TEST=On Mandolin the eMMC controller both disappears in the Windows 10
device manager and in dmesg on Ubuntu 2022.04 LTS
TEST=Morphius with NVMe SSD still works
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5453b69df776d2ce1f3be11e37cd26c8c64f0cd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
GPP_C06 is the report pin of the touchpanel and has no actual function.
Disable this pin to solve the leakage problem.
BUG=b:298529441
BRANCH=none
TEST=Test success by EE.
Change-Id: I13f25788c0258639da4e277e7a15454a08d1599b
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77716
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make naming convention consistent across all functions return values.
BUG=b:296439237
TEST=Boot to OS on Skyrim
BRANCH=None
Change-Id: If86805b39048800276ab90b7687644ec2a0d4bee
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77536
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit dc7cc5bc6edf ("mb/google/skyrim: Disable
USE_SELECTIVE_GOP_INIT") but limits the default enablement to Skyrim
variant only, to allow for continued testing.
BUG=b:271850970
BRANCH=skyrim
TEST=build/boot ChromeOS R117+ on google/skyrim, verify no display init
failures with feature enabled on cold/warm boots or S0i3 resume.
Change-Id: I21c70111a5f407a7e8dd1ad1f2c2759ddb91893e
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update PLDs to match the port layout:
Front (left to right):
A4, A3, A2
Back (left to right):
C0, A0, A1
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port7/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port7
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port4
Change-Id: I682a153d6b757e1b66373c622a6fcfbf389184e3
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77877
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update PLDs to match the port layout:
Front (left to right):
C0, A1, A0
Left side:
C1
Also enable the usb 3.1 device.
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port2
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port6/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port2/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port6
(Ports 5 and 6 are not used on boxy but are peered by default)
Change-Id: I1563d9eaa27353c8c97225a0a6ecc238e9275ce2
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
This patch eliminates the need to maintain separate FMD files for rex
variants and rex variants with ISH. It does this by using the
BOARD_GOOGLE_MODEL_REX_EC_ISH config to differentiate between ME-RW
layout sizes.
TEST=Able to build and boot google/rex and google/rex_ec_ish.
Change-Id: Ibb6ee9aad9fb68198c6c1a1d5978f77d53a2e3ac
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77895
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 449c6d981c216e05d5238056f03c7794e43600ec.
Reason for revert: (EVT board build does not exhibit shutdown followed
by warm reboot)
This commit reverts the workaround that limits the TCC activation
temperature. The original issue that was reported (shutdown followed
by warm reboot) was not seen in the EVT board build, so this change is
likely unnecessary.
Change-Id: I22adcdee6512e57ad0b6d531f2611e22a95c863e
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that the driver skips
initial probe during kernel boot and prevent privacy LED blink.
TEST=Boot to OS, check camera LEDs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib9375d602171aa5018b1add1deac3021724dc207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add fw_config - DB_1A_HDMI for craaskana, and disable C1 PMC mux conn
for HDMI.
BUG=b:296791122
TEST=build and check HDMI function works on craaskana
Change-Id: Ibaa0cd917a23b7f670ecd648765d1eb566edfe61
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77890
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
|
|
There are going to be skus without stylus and fingerprint module.
Disable stylus and fingerprint module based on fw_config.
BUG=b:290689824
TEST=emerge-rex coreboot
Change-Id: I047aae06c4a915d0392edc836757b882a261c178
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77647
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update fw_config settings for karis:
| | | 0 --> STYLUS_ABSENT |
| Bit 2 | STYLUS | 1 --> STYLUS_PRESENT |
| | | |
| Bit 3-5 | AUDIO | 0 --> ALC5650_NO_AMP_I2S |
| | | |
| Bit 8-9 | MIPI_CAM | 0 --> UF_CAM_HI556 |
| | | |
| | | 0 --> FP_ABSENT |
| Bit 10-11 | FP_MCU | 1 --> FP_MCU_NUVOTON |
| | | |
| | | 0 --> WIFI_CNVI |
| Bit 13 | WIFI_TYPE | 1 --> WIFI_PCIE |
BUG=b:290689824
TEST=emerge-rex coreboot
Change-Id: I1df30ad32d212a36b8a5bd7324f3eb8045b2795c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:264960828
TEST=USB2 and USB3 ports are peered correctly in the kernel:
Before:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port4
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port5
After:
$ cd /sys/devices/pci0000:00/0000:00:14.0
$ ls -l $(find . -name peer)
./usb1/1-0:1.0/usb1-port1/peer -> ../../../usb2/2-0:1.0/usb2-port1
./usb1/1-0:1.0/usb1-port2/peer -> ../../../usb2/2-0:1.0/usb2-port3
./usb1/1-0:1.0/usb1-port3/peer -> ../../../usb2/2-0:1.0/usb2-port4
./usb1/1-0:1.0/usb1-port4/peer -> ../../../usb2/2-0:1.0/usb2-port6
./usb1/1-0:1.0/usb1-port5/peer -> ../../../usb2/2-0:1.0/usb2-port5
./usb2/2-0:1.0/usb2-port1/peer -> ../../../usb1/1-0:1.0/usb1-port1
./usb2/2-0:1.0/usb2-port3/peer -> ../../../usb1/1-0:1.0/usb1-port2
./usb2/2-0:1.0/usb2-port4/peer -> ../../../usb1/1-0:1.0/usb1-port3
./usb2/2-0:1.0/usb2-port5/peer -> ../../../usb1/1-0:1.0/usb1-port5
./usb2/2-0:1.0/usb2-port6/peer -> ../../../usb1/1-0:1.0/usb1-port4
Change-Id: I5fe8066e361da62b747464b2ec09bcc6e7dda0fe
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77867
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
UWB on Rex will have 2 options to connect to the SoC:
1. Through GSPI1 (muxed with FP)
2. bit-bang over GPP
This CL adds GSPI1 option. BB may be added later.
BUG=b:263413448, b:263499898
TEST=UWB ranging works on Rex with this CL
Change-Id: I93b3bcef84d775866df43d00c934f013e9f85c47
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76665
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
1. WIFI_SAR_ID_4: AX211
2. WIFI_SAR_ID_5: AX203 (without WiFi-6E)
BUG=b:293360900
TEST=emerge-nissa coreboot
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I6c4705d25d927aaefbc8814ea1df3b4c36b30968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77790
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kuldax-refresh use USB Hub, add fw_config probe for USB Hub.
BUG=b:275335023
BRANCH=brya
TEST=Built and check firmware log.
Change-Id: Ib983ca527a891718f317336597faad66d076247f
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
variants
This enables DRIVERS_INTEL_MIPI_SUPPORTS_PRE_PRODUCTION_SOC for rex
variants boards with ES SoC to load pre-production signed IPU FW from
IPU kernel driver to make Camera function properly.
BUG=None
TEST=Build rex and check if SSDT-IPU0 includes the correct value for
"is_es" with Meteorlake ES and QS SoC.
Change-Id: I407d1932762622652939e8568fe34c704bc3b433
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77855
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
