| Age | Commit message (Collapse) | Author |
|---|
|
The power_limits_config variable for ADL/RPL is array data, but we got
soc_power_limits_config variable without its index. So correct the
code to get the proper pointer of the data for current CPU SKU.
I tried to override the PL4 value to 80W from 114W with following
table in ramstage.c as a test for bug b/328729536.
```
const struct cpu_power_limits limits[] = {
{PCI_DID_INTEL_RPL_P_ID3, 15, 6000, 15000, 55000, 55000, 80000},
}
```
And then verified the msr_pl4 value on ChromeOS using Intel PTAT tool.
- Before this patch: msr_pl4 was not changed, it's always 114
- After this patch: msr_pl4 was changed to 80
BUG=None
BRANCH=None
TEST=Built and tested the function could adjust PL4 on xol in local.
Change-Id: I9f1ba25c2d673fda48babf773208c2f2d2386c53
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update GPIO configuration according to the schematic changes. The
locations of speaker and DMIC are swapped.
- Speaker: I2S2 -> I2S1
- DMIC: GPP_S2/GPP_S3 -> GPP_R4/GPP_R5
BUG=b:318584606
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I3468d79f33d9d9ef8377ccf0f8f628956b02d3c3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81444
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
ISH Firmware name needs to be configured only when full sensing
capabilities are enabled through ISH_ENABLE FW_CONFIG. Similarly DMA
property needs to be added only when UFS is enabled through STORAGE_UFS
FW_CONFIG. Hence configure the ISH device at run-time based on
FW_CONFIG.
BUG=b:319164720
TEST=Build Brox BIOS image and boot to OS.
Change-Id: I678416acd48e03ab77ae299beae6e295a688b8df
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81418
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add Synaptics touchpad via HID-I2C interface in I2C5 bus for glassway.
BUG=b:331677400
BRANCH=firmware-nissa-15217.B
TEST=emerge-brya coreboot and check touchpad function work.
[INFO ] input: PNP0C50:00 06CB:CE9B Touchpad as /devices/pci0000:00/0000:00:19.1/i2c_designware.5/i2c-17/i2c-PNP0C50:00/0018:06CB:CE9B.0001/input/input4
[INFO ] hid-multitouch 0018:06CB:CE9B.0001: input,hidraw0: I2C HID v1.00 Device [PNP0C50:00 06CB:CE9B] on i2c-PNP0C50:00
Change-Id: Ifbb2cb750a80bc6e8f96609257dcd1e695ad1fa4
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Create the sundance variant of nissa reference board by copying the
template files to a new directory named for the variant.
Due to new_variant.py limitation that repo can no longer be used in
inside, created this CL manually following google suggestion.
BUG=b:328505938
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_SUNDANCE
Change-Id: Ia8ba318f18d2cac69898687311631778e61bf2ea
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81347
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
|
|
Add a new Kingler follower device 'Kyogre'
BUG=b:318614302
TEST=emerge-corsola coreboot
Change-Id: Iae3857a9f8edadcc2eee3500fda2e76c0334221c
Signed-off-by: Kei Hiroyoshi <hiroyoshi.kei@fujitsu.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81218
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Change-Id: If68303cd59b287c8a5c982063b2ab75fd74898d6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
Currently, simply changing the wake event configuration to ANY does
not completely resolve the issue of inserting a pen not waking the
system. The pen actually needs to wake up the system both when plugged
in and when pulled out. This is because in the pen's GPP_F15
configuration, the original attribute is EDGE_SINGLE, which should be
changed to EDGE_BOTH.
BUG=b:328351027
TEST=insert and remove pen can wakes system up.
Change-Id: I1823afd0bcb86804227117d2d5def38788bc7387
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81441
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Create the yavista variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:321583226
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_YAVISTA.
Change-Id: I6fa464a4dcd9551a42e8746e64c724b3582dbe02
Signed-off-by: Hsueh Rasheed <hsueh.rasheed@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80342
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Wake signal from EC is routed to GPP_D1 and hence GPE_EC_WAKE
corresponds to GPE0_DW1_01. Fix GPE_EC_WAKE configuration.
BUG=b:329026602
TEST=Build Brox BIOS image and boot to OS. Trigger suspend and wake up
using EC generated events like AC connect/disconnect.
Change-Id: Ifb89bd0de7b7fc316792e801ed5a1d3f25ca5b1c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
Change-Id: Ieaaba5b36796d97449896b8475744a21f01e93d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Return statement is not useful in void function.
Change-Id: I8cf020de335e4da933b7bbdc27b7ac6f31afe885
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81430
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Other files in the commits that added these files were licensed under
GPL-2.0-only, and the project as a whole is GPL-2.0-only, so use that
as the license.
Change-Id: I6c1a7ba582f61f98069ebf3857a8b5bdc8588c3e
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81421
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Assign GPP_C0 and enable only the touchscreen. Before modification,
GPP_C0 supplies power to the touchscreen and sensor at the same time.
Now the hardware circuit has been modified, GPP_C0 supplies power to the
touchscreen alone. After the software is synchronously modified, when
the device enters suspend(S0ix), GPP_C0 will not enable VDD, which can
reduce the standby power consumption of the touchscreen when it is
suspended(S0ix), which is about 2.1mW.
BUG=b:304920262
TEST= touchscreen function workable
Change-Id: Ia06209aa8303be4fc0669c5d6e5d7a06e8e9ab99
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81265
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Configure I2C0/1 timing in devicetree to meet timing requirement.
(THIGH(us) minimum is 0.6us).
Before:
I2C0 : THIGH(us) 0.595us
I2C1 : THIGH(us) 0.582us
After:
I2C0 : THIGH(us) 0.673us
I2C1 : THIGH(us) 0.666us
Change-Id: I79af4fde4eb08d4eb896794756a633701bebb755
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81348
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The previous value of 32MB was set to meet Google's ChromeOS reqs,
but hampers real-world performance in Linux/Windows, so increase it
to 128MB to match the "auto" default for the Picasso UEFI firmware.
TEST=build/boot Windows on google/zork (morphius), verify UMA set
to 128MB.
Change-Id: I8c6487a4cb8155f826d20fd3ceca87859829199c
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81364
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
This patch creates a new tivviks variant, which is a Twinlake
platform. This variant uses Nivviks board mounted with the
Twinlake SOC and hence the plan is to reuse the existing
nivviks code.
BUG=b:327550938
TEST= Genearte the Tivviks firmware builds and verify with boot check.
Change-Id: Ia833a1dad45e13cd271506ade364b116c5880982
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81262
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Set FW_CONFIG bit 21 to enable ISH PCI device and define ISH main
firmware name so ISH shim loader can load firmware from file system.
ISH also need to be enabled if STORAGE_UFS is set.
BUG=b:280329972
TEST= Set bit CBI FW_CONFIG bit 21
Boot Brox board, check that ISH is enabled and loaded
lspci shows: 00:12.0 Serial controller: Intel Corporation Alder
Lake-P Integrated Sensor Hub (rev 01).
Change-Id: Iadc5108c62737d27642a6948c00b5c122541aaba
Signed-off-by: Li Feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80773
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yuval Peress <peress@google.com>
|
|
Select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS in brox Kconfig.
This enables a single binary for both SKU1 and SKU2. For SKU2, upon
boot from cold reset, it will disable the UFS Controller and then
trigger a warm boot.
BUG=b:329209576
BRANCH=None
TEST=Boot image on SKU1/SKU2 and check S0ix working.
Change-Id: Iabd0b3a83aa386e09310b671632368807a4018d4
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update eMMC DLL settings based on Craaskov board.
BUG=b:318323026
TEST=executed 2500 cycles of cold boot successfully on all eMMC sku
Change-Id: I56f8329c28261c2bcae9d058da929be6763b293c
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update touchpad and touchscreen I2C timing.
- Data hold time: 300ns - 900ns
BUG=b:328724191
BRANCH=firmware-nissa-15217.B
TEST=Check wave form and met the spec.
I2C1 (touchscreen) Hold time from 83.58ns to 413.87ns
I2C5 (touchpad) Hold time from 95.93ns to 425.27ns
Change-Id: I65fb1298f9e96ab0b63aba436f6a319f21b38925
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Shawn Ku <shawnku@google.com>
|
|
Adjust touchscreen power sequencing for eKTH5015M.
The INX touch panel (eKTH5015M) contains a pull-up register which causes TCHSCR_REPORT_EN pull-up abnormally from Z1 power on.Because the t25 must be at least greater than 20ms, TCHSCR_REPORT_EN is initialized to GPO_L in the early stage (romstage) to meet the spec.
BUG=b:328170008
BRANCH=firmware-nissa-15217.B
TEST=Build and check I2C devices timing meet spec.
[INFO ] input: Elan Touchscreen as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-ELAN0001:00/input/in4
Change-Id: I50f9c21ddee2bc9c1d313f63049cb587b4ae047a
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81135
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, inserting the pen does not wake the system, only removing
the pen does. This is caused by the wake event configuration being
DEASSERTED, so change it to ANY.
BUG=b:328351027
TEST=insert and remove pen can wakes system up.
Change-Id: Icdea995c2be04ea459e985f79269e49faf88248d
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Create the bujia variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:327549688
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_BUJIA
Change-Id: I453a50f1aa64f8d4119bf0f860d928aa3e00a144
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81198
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
|
|
This patch enables the `SOC_INTEL_COMMON_BASECODE_RAMTOP` configuration
at the SoC level for all MTL devices. This change streamlines the
configuration process, avoiding redundant selections on individual
mainboards.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot functionality on google/ovis and google/rex.
Change-Id: I3aa3a83c190d0a0e93c267222a9dca0ac7651f9c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch ensures Ovis baseboard can select RAMTOP caching to improve
the boot time w/o any runtime hang.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot on google/ovis with ~30ms savings in boot time.
Change-Id: Ic0b73eb8fb9cd6ca70d3d7168b79dfd0fbc550e3
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
NVMe using clk_src[0] and clk_req[1] mapping to hardware design,
Due to inconsistency between PMC firmware and FSP, we need to set
clk_src to clk_req number, not same as hardware mapping in coreboot.
Then swap correct setting to clk_src=0,clk_req=1 in mFIT.
BUG=b:328318578
TEST=build firmware and veirfy suspend function on NVMe SKU DUT.
Cq-Depend: chrome-internal:7063434
Change-Id: I1777310782a0f4417bd1bb21287bec5852be966e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81230
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Modeled after the Rex Kconfigs for ISH.
Change-Id: Ic670d550a9aaad64e52489d895b8aac2aee4b5ed
Signed-off-by: Yuval Peress <peress@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81050
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define SSFC bit 0-1 in coreboot for add 2nd BOE G7500 touchscreen.
BUG=b:329339069
BRANCH=firmware-nissa-15217.B
TEST=Check touchscreen can detect and function work.
[INFO ] input: GTCH7503:00 2A94:A804 as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-GTCH7503:00/0014
Change-Id: I85688919864e3cac1beb2442ef3e23fe9d5f916c
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Now that EC software sync has been verified to work on Brox, we can
enable it by default.
BUG=b:326152804
BRANCH=None
TEST=Verify that SW sync occurs
Change-Id: I3d356c006fc448125605761f7328d1f1e203a7c4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81211
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pull down USI_REPORT_EN(GPP_C6) in romstage to solve
an abnormal peek pull high before BL_EN.
Because power sequence no meet spec, pre #comment36,
it may have ghost touch.
BUG=b:326337003
TEST=FW_NAME=omnigul emerge-brya coreboot, measurement of HW and test
touch detection by evtest
Change-Id: I66f4a7915f135927fbc0a16254dece202dfc23a2
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80769
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS to use unified AP
FW for UFS/Non-UFS SKUs.
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I85c3c1c7ccaae9d46b66d3e7a2efea6dc9056188
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81107
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Create the nova variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:328711879
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_NOVA
Change-Id: Ie1cee43f0e2545288130bcc5152075603695c395
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
|
|
Disable unused controllers in overridetree.cb by referring to xol proto2
schematics. Enabling unused controllers blocks entering s0ix.
- I2C3
- SATA
- PCIE RP8
- PCIE RP9
- GSPI1
BUG=b:328318578
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I1be7caf8234c32406aa2cff8fc7fe9fa39b16d89
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81105
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update psys_pmax value to 122 from 145. This value is from internal
power team.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I8bc58343d5736e2457db006972dc229e16d3fe59
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81104
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Enable Acoustic noise mitigation for xol. The setting values are from
internal power team.
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_4
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=None
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I6165ae6ca73d1467a1d2cc7bd545298bd4c2f54f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81103
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
For SKU1, wake pin is WLAN_PCIE_WAKE_ODL.
Update gpio config and corresponding ACPI for WoWLAN.
BUG=b:327379404
BRANCH=None
TEST=Boot image on SKU1 and check Wake on WLAN from S0ix.
Change-Id: I04c35da2c9ac57cafdf7f7a35d83ab2e7a05fe4a
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update eMMC DLL values to improve initialization reliability.
BUG=b:327123701
TEST=Improve reboot on MB with eMMC smoothly.
Change-Id: Ice9ee217acf7dc6e3e704bc82529e0b9a8faf184
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80779
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
|
|
Currently, the oak boards are the only boards that build the ChromeEC
by default as a part of the coreboot build.
As a part of replacing the chromeec submodule with a different build
mechanism, disable this default.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Idd4fe45e52dbdd1c8dccf0d2c09d5cf6d61aa839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81023
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Add VGPIO configurations for NVMe on PEG60.
BUG=b:326481458, b:372086400
BRANCH=firmware-brya-14505.B
TEST=Verified DUT could detect NVMe.
Install ChromeOS into NVMe and boot from it.
Change-Id: I5520dc2a4bf6e788701a774674d223b7e8ad5b44
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add FW_CONFIG probe to separate touch panel settings.
TOUCH_PANEL_ENABLE/TOUCH_PANEL_DISABLE
Use different gpio tables based on the value of TOUCH_PANEL.
BUG=b:325987249
TEST=emerge-nissa coreboot and run in DUT
Change-Id: I23c62406a932815ff1cfafe05b70468b1f9cca54
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
|
|
Add wifi sar table for dochi
BUG=b:326137130
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Iaf90756eb318bef1ffcda9368a976c0ca209a100
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Turn off SD ASPM L1.1/L1.2 as w/a for wlan DMA resume failure
We completed 4 runs for each of the 2 tests - power_idle and power_VideoCall. Here are the averages for both the tests:
L1ss disabled SD plugged power idle test: 735.3875
L1ss enabled SD plugged power idle test: 737.2335
L1ss disabled SD plugged power video test: 333.29325
L1ss enabled SD plugged power video test: 333.442
BUG=b:254382832
TEST=test pass over 10k cycles
Signed-off-by: Jason Nien <finaljason@gmail.com>
Change-Id: I4d903f0f6333ffa18069e42be3c932aeae8013d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80237
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=none
TEST=Verify CSE telemetry data in boot time data on Yahiko.
Before:
```
yahiko-rev9 ~ # cbmem -t
71 entries total:
0:1st timestamp 197,583 (0)
```
After:
```
yahiko-rev9 ~ # cbmem -t
76 entries total:
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 49,000
945:CSE started to handle ICC configuration 49,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 51,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 168,000 (117,000)
0:1st timestamp 195,861 (27,861)
```
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3f90d0462cb766655bf8e59a90bc550ceefb2256
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79768
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For boot beep functionality, relevant register values are
required to be updated.
BUG=b:324528901
BRANCH=None
TEST=Build & verified Boot Beep functionality on Brox
Change-Id: If236c8ac173a279db676af412377fa4e4122c1cd
Signed-off-by: poornima tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80416
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change ClkSrc index for NVME to 0 from 1 by referring to proto2
schematics.
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I7ea1cd7d8e16d4cee953e931d2f1829eae7d1978
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80768
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add 2 configuration on Kconfig for glassway.
- DRIVERS_GENERIC_GPIO_KEYS
- DRIVERS_GENESYSLOGIC_GL9750
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: Id7e358d2f472cd435d2828f6256f5ee91dfb8ef6
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80766
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Refer to the reference board of nivviks, and update GPIO settings
via glassway schematic of ca24a_r10_240108_v3_mb_gsen_gmr.pdf.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: I0de743746160c6eb081cb9a061ac1703b01ba5b4
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Several users complained of link's fan not running at all, particularly
when using ChromeOS Flex. Enabling auto fan control at boot/s3 resume
resolved the issue for them.
Change-Id: I8f0db6b6c94fac2e0dcb580be0f6df839780c38c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80713
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No Windows driver exists or is needed, so hide to prevent an unknown
device from being listed in Windows Device Manager. Same change was
made for frostflow variant previously.
TEST=build/boot Win11 on skyrim, verify unknown device for the
fingerprint reader no longer present.
Change-Id: Ia700aa4ccd478bc734db012e1419e566a5dcf493
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80711
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add STORAGE config in FW_CONFIG to support NVME sku.
- STORAGE_UFS : 0
- STORAGE_NVME: 1
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: Id8316f643ba9a55319b67431a24a507e92419aa7
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80767
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Refer to the reference board of nivviks, and update devicetree settings
via glassway schematic of ca24a_r10_240108_v3_mb_gsen_gmr.pdf.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: Ibbb10a373bd5fa52a0833b81133517d2a088536b
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80742
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IOEX was replaced with GPIOs, this CL makes the required changes
BUG=b:325533052
TEST=Built FW image correctly.
Change-Id: I09ebba336b179cb36c6801b47ee0be5ade08c257
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80570
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
GPP_F19 and GPP_F20 sre set incorrectly previously. Change them to not
connected according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Change-Id: Ifb6da1f8696f44cb47be3d1de83c55e62b12a9e9
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80569
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Starting from MT8195, MediaTek platform supports "dram adaptive" to
automatically detect dram information, including channel, rank, die
size..., and can automatically configure EMI settings. So we can just
pass a placeholder param blob to `mt_mem_init_run` by enabling this
option.
Platforms (MT8173, MT8183, MT8192) which do not support "dram adaptive"
need to implement `get_sdram_config` to get onboard DRAM configuration
info.
TEST=emerge-geralt coreboot && emerge-asurada coreboot
TEST=CONFIG_MEDIATEK_DRAM_ADAPTIVE is set to y on geralt
TEST=CONFIG_MEDIATEK_DRAM_ADAPTIVE is no set on asurada
Change-Id: I05a01b1ab13fbf19b2a908c48a540a5c2e1ccbdc
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/deku using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: Iedaff8a793f1ba5d2b97352b95c4dfdd2b818ebd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80664
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
|
v
ramstage (A19/1, A20/1)
Ideally, we don't need SSD power sequencing at ramstage, but due to the
fact that Karis has RO locked, any change in the bootblock won't be
applicable for FSI'ed karis devices. Therefore, we're keeping the
existing ramstage power sequencing flow as is
TEST=Able to build and boot google/karis using NVMe without any
problems. S0ix and read/write from/to SSD are also normal.
Change-Id: I79171a7830b75f5c20bbe30023f2814a62743a13
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80663
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/ovis using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: I891b5a6d2c29f5d940793a4e90215265f2a4fcd8
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/rex0 using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: Idde2f7693771f1d7e3171e51232d1bb899bfe33e
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
|
v
ramstage (A19/1, A20/1)
Ideally, we don't need SSD power sequencing at ramstage, but due to the
fact that Screebo has RO locked, any change in the bootblock won't be
applicable for FSI'ed screebo devices. Therefore, we're keeping the
existing ramstage power sequencing flow as is.
TEST=Able to build and boot google/screebo using NVMe without any
problems. S0ix and read/write from/to SSD are also normal.
Change-Id: I0ee1fa4613178da8771c9e6b5ee871e50ea6324c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80640
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early EC Sync does not need to be enabled in coreboot as EFS2 is being
enabled in the EC.
BUG=b:326152804
BRANCH=None
TEST=emerge-brox coreboot
To be tested with EC sync enabled
Change-Id: I08bdbe9f3dcea837b0b148adc137c03d3461877a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80689
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:320203629
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot built FW image correctly.
Change-Id: I8db065e25e21406f1966d8020a3b926b3a62ae12
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add supported memory parts in mem_parts_used list, and generate SPD ID
for these parts.
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
K3KL6L60GM-MGCT 1 (0001)
H58G56AK6BX069 2 (0010)
H9JCNNNBK3MLYR-N6E 3 (0011)
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go ADL lp5 \
src/mainboard/google/brya/variants/glassway/memory/ \
src/mainboard/google/brya/variants/glassway/memory/\
mem_parts_used.txt"
Change-Id: I00ae3efe8e554f44cee5a27ac88c5d65eb95f7fb
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
|
|
Add support memory parts for Xol.
- Samsung K3KL6L60GM-MGCT
- Samsung K3KL8L80CM-MGCT
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Proto board can boot to ChromeOS.
Change-Id: Ic6a36e40f0f93109f296c5cc67a368ace81bd217
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80637
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Update memory configuration following proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Proto board can boot to ChromeOS.
Change-Id: I59aabe0870317092f59701bdf88b53bf9731377a
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update initial DTT policy and TCC setting for Xol. The setting values
are from internal power team.
- Critical CPU temparature: 105 -> 99
- TCC offset: 90 -> 94
BUG=b:323989520
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I546b313a1e6af16029309174a5bed2d1e4aa4d11
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80410
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set tdp_pl1_override to 15 for performance required by the thermal team.
Fix policies.critical index from 2 to 0.
BUG=b:313833488
TEST=emerge-nissa coreboot
Change-Id: I5341bd3d4842f9298a2f5d9e589918bb1b06ba69
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Keeping the PM timer enabled will disqualify an ADL system from entering
S0i3, and will also cause an increase in power during suspend states.
The PM timer is not required for brya boards, therefore disabling it.
Fixes: 0e90580 (soc/intel: transition full control over PM Timer from
FSP to coreboot)
This mirrors an identical commit for google/brya: 1ce0f3aab72d
("mb/google/brya: Fix S0i3 regression")
TEST=Boot Linux on google/drobit, verify S0i3 counter incrementing after
exiting S0ix suspend states.
Change-Id: I644e42388c0f6127512bf52e774b79721601ecc9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80612
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the glassway variant of the nivviks reference board by copying
the template files to a new directory named for the variant.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=None
Change-Id: I597666a5be6f71b82c7baddbe343da3d5117dd1c
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Enable DPTF functionality for brox board
BRANCH=None
BUG=b:324360936
TEST=Built and tested on brox board
Change-Id: I0315f7f45688ccc36d321d6be4fa4fac7559a16b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I838ada7dfe948c58a5bb9805ade289b07368aa63
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iacfef5f032278919f1fcf49e31fa42bcbf1eaf20
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79920
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iea7f616f6db579c06722369c08de7cf7261dece8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79919
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Probe usb ports by FW_CONFIG setting to disable C1 port on
beadrix poin2 new daughterboard without C1 port.
BUG=b:316365055
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot
Change-Id: I494a922d2b04dcf7bd35680f5d95f8463e225f2d
Signed-off-by: Kevin Yang <kevin.yang@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add beadrix supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. CXMT CXDB4CBAM-ML-A
BUG=b:321830738
TEST=Use part_id_gen to generate related settings
Change-Id: I3a6925395b52dc7aa5c0f93b8820099369db4dbf
Signed-off-by: Kevin Yang <kevin.yang@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Select this at the SoC level (like other modern Intel SoCs), and drop
it from individual boards which selected it.
Change-Id: I8ebb915fbc21f82e39304473b0fcaa620559b5d5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80558
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib7beed7218f317bc2352b65a6191ef1cdaa0742d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: Id859c981d0bf5dcf90bf6858607a9fe726516309
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
When 'reset_gpio' and 'enable_gpio' properties are defined in
overridetree.cb, the kernel will power on the FPMCU. If the device was
previously enabled the kernel will reset it.
To avoid situation in which the FPMCU is powered on and reset later we
leave the FPMCU powered off in coreboot and started by the kernel. This
is exactly what other boards do (e.g. brya).
TEST=Boot the board (e.g. karis) and make sure the FPMCU was booted once
(e.g. examine FPMCU console logs)
Change-Id: I5df8d9385be2621c02ccee2d36511a4e80ab87d1
Signed-off-by: Patryk Duda <patrykd@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80457
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For devices that require CNVi Bluetooth select WIFI_BT_CNVI
in FW_CONFIG. Discrete Bluetooth devices need to select
WIFI_BT_PCIE.
BUG=b:319188820,b:325084796
BRANCH=None
TEST=Boot image on SKU1,SKU2 and check BT devices enumerate.
Change-Id: Iba008682fcfa7ddc1ec400649c8742c721666f1d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80564
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setting the EC interrupt GPIO as an APIC is able to solve many
problems that we are currently seeing:
1. Routing through the APIC make the IRQ# associated with this pin
unavailable to claim for other devices in the kernel. This is causing
EC interrupts to not work.
2. Since EC interrupt are not working, we are not able to flash the
EC from the DUT.
3. Also, the GPI_INT configuration does not allow us to set the
polarity of the GPIO, which means that it is by default set as active
high. As a result, we are seeing an excessive number of host command
interrupts to the EC. This disappears when we change the
configuration to APIC and set the polarity as INVERT.
BUG=b:319129926,b:324707182
BRANCH=None
TEST=1. After boot up, check if ec_cros_lpcs driver was successfully
registered. Look for the following string:
"cros_ec_lpcs GOOG0004:00: Chrome EC device registered"
2. Make sure can flash the EC image from the DUT
3. Make sure EC console is not getting continuous stream of host
commands.
Change-Id: I74bff88d2ddbaf1f4b085c31d582bd66e18c438a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80467
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ashish Kumar Mishra <ashish.k.mishra@intel.corp-partner.google.com>
|
|
Change-Id: I7230bb8f9883f186c10f41132a2919c3fd99f8c1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Change-Id: I245eb8a9961e3e0025c0275f306a4d989b532331
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80491
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2909375d38c37332293bd7928ae33d5bb502694f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80490
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Vbt data files extracted from dedede recovery image 120.0.6099.272.
Change-Id: I28485d501e519cdaa06c55c20eba07190c5c6b6f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Eliminates the use of a magic number, and the resulting DID entry in the
_DOD method is the same.
TEST=build/boot google/drallion, dump SSDT and verify DID entry is
unchanged.
Change-Id: Ic929cf7ec6849ba398653226bbe46d27b4e3fa81
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Set the display type for the LCD panel configured via the gfx/generic
driver. This will ensure the correct DID/device address are generated
in the SSDT.
Change-Id: If63374329ed5eb4330517ca1bf2ba1ada24fa54a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80244
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
Change-Id: Id52f7c0e542423ba08eeed89bf9b171e540e10e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
Change-Id: Id93cfea93edfefc8237b53214734531b811b36e4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80202
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the display type for the LCD panel configured via the gfx/generic
driver. This will ensure the correct DID/device address are generated
in the SSDT.
Change-Id: I8f390c58710c91bf77555f664e8f89f08ca59b30
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Jinlon disables the eps device if no privacy screen is present, so add
a second generic gfx device 'no_eps' to handle that case, so that ACPI
backlight controls are generated either way. Add logic to ensure only
one of the two devices is active.
TEST=build/boot Win11 on google/hatch (jinlon), ensure LCD backlight
controls present and functional on device both with and without a
privacy screen.
Change-Id: Icf20de97d26c8be76c84e87d5dc6ed1a4b6dbfbc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80178
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
TEST=build/boot Win11 on google/hatch (jinlon), verify LCD brightness
controls are functional.
Change-Id: I4204a518876bed38584260f7566d4d6c9aaa042f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80177
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT
parts match.
TEST=build/boot Win11 on google/brya (redrix), verify brightness
controls are functional.
Change-Id: I389553b2ddc5b09d165229e2d8066cacf852b82c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80174
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Won Chung <wonchung@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Redundant when generic gfx driver is used
Change-Id: I8ed1eede05f531f4c76e7fa168c2b92fae7e45cb
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The GMA driver generates the brightness controls expecting the name
LCD0, so we need to use it here as well so that the DSDT and SSDT parts
match.
TEST=build/boot Win11 on google/drallion, verify brightness controls are
functional.
Change-Id: I6fbdd0c5606ec8f2c497e85bf46d388957f15fa5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80175
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Puff-based Chromeboxes use a LSPCON for HDMI 2.0 output, but no driver
exists or is needed for Windows. Use the devicetree hidden keyword to
set the ACPI status to hidden for these devices, to prevent unknown
devices from being listed in Windows Device Manager.
TEST=build/boot Win11 on google/wyvern, verify no unknown devices in
Windows Device Manager for either LSPCON device.
Change-Id: Ib646e01a337b8d7baf20a886c49a8cb64d6408f3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78040
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add a board-specific VBT file compatible with the latest FSP release
(requires VBT version 250).
TODO: Update all other volteer VBTs to v250 from v240.
TEST=build/boot google/volteer (drobit) with edk2 payload
Change-Id: Ie25a77be5204dfc8b888082492a285973843037c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80183
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TCHSCR_RST_L signal was originally being configured to 1 in gpio.c but
this was causing some leakage. Configuring it to 0 initially in
romstage fixes this. Also, make sure that EN_PP3300_TCHSCR is
initialized in romstage as well.
BUG=b:322249892
BRANCH=None
TEST=Make brox boots and touchscreen is still working
Change-Id: I5bf1901a3a40a38237b950abcb758f96aebcc1cf
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80300
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is an existing issue for nissa where wake up from RTC wake is not working during suspend_stress_test.
The phenomenon of the issue is that after pulling out the stylus, can see an interrupt storm occurs, checking through:
"cat /proc/interrupts | grep acpi".
When the counter of interrupt is greater than a certain value, "Disabling IRQ #9" will occur, so RTC wake is not working.
Reference: https://review.coreboot.org/c/coreboot/+/65086
This patch skips the locking for GPP_F15 to allow kernel to
configure it later. The interrupt storm of acpi disappears.
BUG=b:321348117
TEST=1. cat /proc/interrupts | grep acpi
there isn't interrupt storm of acpi when pulling out stylus.
2. The stylus tools panel will pop up when pulling out it.
3. Inserts stylus can wakeup DUT after powerd_dbus_suspend.
4. Passed:
suspend_stress_test -c 2500 --suspend_min=15 --suspend_max=20
Change-Id: Ie143c43e0555d17d8a290f17637b537fba806144
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80316
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
EVT mini-build changes redriver IC from PS8745 to ANX7493, the ANX7493 not support DP AUX BIAS, so connects DP AUX BIAS of DB to SOC directly. Add DB_AUX_BIAS bit field to fw_config for compatibility.
BUG=b:320235566
TEST=DP function of MB and DB workable
Change-Id: I53974ec7444912a63d0fe0a9303c9e5d6941f68d
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80259
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
