| Age | Commit message (Collapse) | Author |
|---|
|
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to 8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=b:227165770
TEST=build FW and system power on.
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I262ef14032e0e412c63403dbb8c8fbc6a8b03dd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add WiFi SAR table for taniks.
BUG=b:226690925
TEST=build FW and checked SAR table can load by WiFi driver.
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7b52f71b1fe49c02beaa48410495b81661b58fac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
After assessing the signal integrity, 100 MHz SPI fast speed can be
enabled for SPI ROM.
BUG=b:213403891
BRANCH=guybrush
TEST=Build and boot to OS in Dewatt board version 3.
Change-Id: If0318abf1fed9b1f4ba876f736fdbf92c1ea6933
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on kracko.
BUG=b:223687184
TEST=emerge-dedede coreboot
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Change-Id: Ib12265591e679e6b9ed34299f1256db05147eaef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on drawcia.
BUG=b:223687184
TEST=emerge-dedede coreboot
Change-Id: I683049e9d2b10fc9455ef782ce798f1c453073bc
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on lantis.
BUG=b:223687184
TEST=emerge-dedede coreboot
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Change-Id: I3d8eec1d2f962d42f3be225eef8498e8b722aace
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fix WLAN PCIE speed to GEN2. Dynamic switching between speeds is causing
the PSP to hang when resuming from S0ix suspend. The root cause is still
under investigation. Just disabling PSPP fixes the hang but causes poor
PLT performance.
BUG=b:228830362
BRANCH=guybrush
TEST=suspend_stress_test on AC and DC
Change-Id: I988365e51aca0d6515c5605b3032521cf59d8d30
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63722
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG STORAGE and probe for UNKNOWN, NVME and eMMC.
BUG=b:220039297
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: If83031edcd90ea746704590765102b9b0dee03c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
Taeko/Tarlo uses the WIFI_SAR_ID field in FW_CONFIG to pick which
SAR table to load.
BUG=b:226684990
TEST=emerge-brya coreboot
Cq-Depend: chrome-internal:4676926, chrome-internal:4686953
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I9852553f5c91494db845d45a94e2566248538bba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E512M32D1NP-046 WT:B (Micron)
MT53E1G32D2NP-046 WT:B (Micron)
H54G46CYRBX267 (Hynix)
H54G56CYRBX247 (Hynix)
K4U6E3S4AB-MGCL (Samsung)
K4UBE3D4AB-MGCL (Samsung)
BUG=None
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I1fbdce203afd282cef9fcd7aebbace69d19fbbf1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63706
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the osiris variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:229352299
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_OSIRIS
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I41e088a3415add86cba87c919af23494f816bb24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63650
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPI setting as below:
Normal speed:33mhz
Fast speed:66mhz
Alt speed:66mz
TPM speed:33mhz
BUG=b:225213679
TEST=boot skyrim and verify spi settings.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Icbe4b9f4794f7e883c3819258ede809c3c8922b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Increase RFI Spread Spectrum to 6% for Vell as RF team request. The
default of Spread Spectrum in FSP is 1.5%, and set 1.5% in baseboard
as default.
BUG=b:228929196
TEST=emerge-brya coreboot and pass RF test as before
Change-Id: I7cdca8f51ad18f4ab03e4e6c744b60da68263ce2
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure GPP_R0, GPP_R1, GPP_R2 and GPP_R3 for headset function
enable with ALC5682I+MAX98360.
BUG=b:202671753
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I93070a8096d43557a50e5a545227f2906e299d8e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Based on the latest schematic, exchange I2C port for TPM/touchscreen.
TPM: I2C3 -> I2C1
Touchscreen: I2C1 -> I2C3
BUG=b:202671753
TEST=emerge-brya coreboot
Change-Id: Ifa6235869f34e0038a8ecad33d59654626cf7815
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit d80d88c0fec96b2fff93db87d0c83f4c6754ae7a.
Reason for revert: 100Mhz should only be enabled on DeWatt
on board version >=3. Enabling it on board version 2 will
cause failures.
BUG=b:213403891
BRANCH=guybrush
TEST=Build dewatt
Change-Id: I0b6acd2cda2af35ff33e89e3b339731e35d72cb1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63746
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should no longer be needed because the ASL has been fixed.
Change-Id: I4d1500217bef54fa3d2be397e5e2a155da3f965d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This alias name is required for the mainboard.c code to generate the
appropriate power-off seqeuence for use during orderly S5 shutdown
from the OS. It had been accidentally removed, but is required, so
this patch adds it.
BUG=b:227788351
TEST=compile
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8936a01bd3a6b908033a8c58bd4e84b30d199e98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Configure the power saving pin for Smart Card.
BUG=b:229356121
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Ia17970f717c6ba806d9603031c486bad86e42b37
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
After assessing the signal integrity, 100 MHz SPI fast speed can be
enabled for SPI ROM.
BUG=b:213403891
TEST=Build and boot to OS in Dewatt board version 2.
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I7301d873e36bec4ee46c9d18293f924500ea9aba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63685
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for felwinter board. Please refer Intel doc#723158 for
more information.
BUG=b:221461379, b:226020977
TEST=Verify the build for felwinter board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I25033ea218fa3154eb99af6be43c4198f4db3bcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add conn1 for pch_espi and add type-c port2 for pmc_mux.
BUG=b:220814038
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Idfd7b761496a110f34838abb0fd408b37d390ba2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This CL adds the delay time 50 ms and 20 ms into the RTD3 sequence,
the reason is that the rise and fall times of each signal
may differ by board, and so those board-specific delays
must be taken into account when power sequencing.
We checked power on sequence requires enable pin prior to reset pin,
so added delay to meet the sequence.
Based on BH799BB_Preliminary_DS_R079_20201124.pdf in chapter 7.2.
BUG=b:228907551
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Idecb1c89655c9b8b720c3c65efc77e06e6a8b300
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Remove i2c1 because brask devicetree is already has it.
BUG=b:220814038
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Ic782e1c6434ac57bdf65b3d9f4219bdf32d25b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable pen garage. Pen detect is active low.
BUG=b:229168203
TEST:Build and boot to OS in skyrim. Evtest work as expected
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 1
Properties:
Testing ... (interrupt to exit)
Event: time 1649922170.578779, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649922170.578779, -------------- SYN_REPORT ------------
Event: time 1649922172.070740, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I3bb07af6aebdc355a73148d8be79b1014147f61d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Goodix touchscreen according to the Programming Guide Rev.0.7
BUG=b:228907558
TEST=local build and tested with Goodix touch screen
Change-Id: I35dd3ca76e9e0f17508bef46c90b53b4be5d0033
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63573
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the issue that can't hear the boot beep at dev screen. GPP_B14 is
used for PWM_PP3300_BUZZER and it should set to GPO. Modify GPP_B14 from
PAD_CFG_NF_LOCK to PAD_CFG_GPO_LOCK.
BUG=b:229345416
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot and verify if the buzzer beeps.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I601735ab20974cd992ca5dd6dbaca1517a395aa2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63645
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pick specific VBTs for HDMI, DP, and ABSENT according to FW_CONFIG.
BUG=b:220241277
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Icc8fbef1467605505459fce264697f670591c81e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63604
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
select DRIVERS_GENESYSLOGIC_GL9750 to disable ASPM L0s.
BUG=b:229213455
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ie89fa6c66974284063cd25ae8097db94a93326ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Followed the Brya series to lock the gpio pins in baseboard. Variant
should honor locked gpios from baseboard, but not the last. Variant can
add more gpios to lock if needed.
BUG=b:216671701
TEST='emerge-nissa coreboot chromeos-bootimage', flash and verify that
nivviks boots successfully to kernel.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib34ca287596a6958407a944d0caf53f4bcc60d9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add TPM I2C for crota to avoid TPM I2C fail.
BUG=b:229200525
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I8054e623fb0c3c549c3373982ce9d4fbd57e0fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add TPM I2C for crota to avoid TPM I2C fail.
BUG=b:226315394
TEST=USE="project_crota emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I7eb3ce6c2faf857c8f5d789af395e315caea4102
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
update STT setting for dewatt.
BUG=b:228040295
BRANCH=guybrush
TEST=build, verify the parameter has been applied to
the system by checking the AGT tool.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Id319d42747dd0d5f6a9ca727635d85e6b9bd65af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Remove EC_ENABLE_LID_SWITCH since this causes a duplicate SW_LID
entries. The other SW_LID entry is generated by MKBP.
BUG=b:228907256
BRANCH=guybrush
TEST=Lid open close triggers events on Nipperkin
Change-Id: I5c1cf7aeac8405bce7bfc77110eceaf3e5383fe7
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:227296841
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
pass PLT criteria: S0 > 600ms, s0i3 > 14 days
Change-Id: I9c61e1d0f3db8b9885040255d6de266616768b68
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Set the BT USB device to use GPIO for the power status. This causes an
ACPI `_STA()` function to be generated that returns the power status of
the BT USB device, rather than always returning `0x1`. This `_STA()`
function can be used during boot to skip enabling the device (and
performing the associated sleep) if the device is already powered on.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I72f6b28671efddfbef53f328d904a05f73f39efa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Update the build scripts to inject variant specific SPDs into APCB.
BUG=None
TEST=Build and boot to OS in Skyrim boards with all the concerned memory
parts.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3b3f6f248d54681c6f55c00660d1f2988ae906ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63600
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts and generate the associated DRAM part ID.
Also for MT62F2G32D8DR-031 WT:B memory part, add a custom SPD that
configures the DRAM speed at 5500 MHz. Use this custom SPD until that
part can operate at full speed (i.e. 6400 MHz).
BUG=None
TEST=Build Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id87e79f5d6187d57d74487841c09aa309f1450b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Setup the following acoustic noise mitigation features:
1) Slew rate for both IA and GT domains to 1/8
2) Disable Fast package C ramp
BUG=b:229046516
TEST=build and verified by power team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ifb5700391e33818878994f205acae7ee3b1b96d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Disable PSPP parameters for WLAN card on Nipperkin. This feature
is causing S0ix resume hangs.
BUG=b:227296841,b:228830362
BRANCH=guybrush
TEST=Suspend stress test passes on Nipperkin
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I38f05b92ace4aba61163194a6a638915882b8871
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63593
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some brya variants may need to initialize and finalize some
variant-specific devices during ramstage, therefore add the
commonly-used hooks and callbacks to support this.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iede6dc5a5b9a7385fedd59d4eeaaba118eff0e20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:228448327
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
check ACPI device "LCD" in SSDT
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I42c5abdbe3bfab72016d56399278a7aff9e33377
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
We don't want to enable the speaker on init. It will be enabled while
using GPIO AMP codec in depthcharge.
BUG=b:223289882
TEST=boot Nipperkin and Dewatt and then verify the devbeep and gpio
values in kernel
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Change-Id: Id874421d7464b15be6e521576696bb97e6b22d6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Configure lcnt and hcnt directly to give the required frequency, tHIGH
and tLOW, instead of using rise and fall times. Aim for a frequency of
390 kHz to make sure it doesn't exceed 400 kHz on different boards.
BUG=b:227517802
TEST=Probe the clock line and check that it meets the requirements for
frequency, tHIGH and tLOW.
Change-Id: I4d4f877c1f0cd9aacd3fa152890b7ef82e059f78
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the craask variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_CRAASK
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Icf03e3f18468d7dd207ab200fa2dcf96afd02f8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Fixes the following build error:
src/mainboard/google/brya/mainboard.c: In function 'variant_generate_s0ix_hook':
src/mainboard/google/brya/mainboard.c:157:40: error: parameter name omitted
void __weak variant_generate_s0ix_hook(enum s0ix_entry)
^~~~~~~~~~~~~~~
BUG=None
TEST=`abuild -a -x -c max -p none -t google/brya` now succeeds
Change-Id: Id578766e2a3b7647e920740dde3e356a7db39d4d
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Select the Bayhub LV2 driver, and implement power sequencing as per the
datasheet.
BUG=b:223304542
TEST=Check that connecting an SD card works as expected in the OS. Probe
the EN and RST signals and check the timing requirements are met.
Change-Id: Id1cca2024e06e5b2c7cefd22aa0b735bc542dc3b
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Based on the latest schematic, change MAX98360 AMP interface from I2S2
to I2S1 due to Intel BT offload concern.
BUG=b:202671753
BRANCH=firmware-brya-14505.B
TEST=dmidecode -t 11
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Change-Id: I9ee45dbceabdedd39a9befffb8002b8bc3d4bfb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add WWAN power sequence setting to meet spec
BUG=b:220084872
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: If6d3f965b8f6b6753446f55a8bd47d3b0c1ae7be
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Idcaf30c622bf5dc0f1295f2639c656086d01ff7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The workaround causes the eMMC controller to not enter its L1
during the boot process
BUG=b:220079865
TEST=Build FW and run stress exceed 2500 cycles.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I2a5888e943c1ebf83a54f9b172f986f8b13d9b6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I88406fa1b54312616e6717af3d924436dc4ff1a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
consumption
To achieve low power consumption, we disable unused PCIe and SATA
pins at beadrix/overridetree.cb according to baseboard/devicetree.cb
and mainboard schematic. Original measured beadrix board's power
consumption is about 250 mW. After we disable unused PCIe and SATA
pins, as well as, enable the other low power MUX CL (3487086: USB
MUX: Update low power mode of MUX anx7447 used as MUX only |
https://chromium-review.googlesource.com/c/chromiumos/platform/ec/
+/3487086), the measured power consumption achieves about 110 ~ 116
mW, as well as, meets Google battery life for 14 days in the suspend
state and Intel low power consumption about 116 mW.
BRANCH=dedede
BUG=b:204882915
TEST=on beadrix, measured power consumption meets Intel power
consumption.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: I79ec524c5ce8f2a79da4aeba084786fb9dac17af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62776
Reviewed-by: Teddy Shih <teddyshihau@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all guybrush family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:227240985
BRANCH=guybrush
TEST=manual test on Dewatt:
Volume Up/Down and Power buttons, Tablet Mode switch
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: Ic9980f2b5bf10b12f2bd666212b5bce925dc323d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63394
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are currently two issues related to the WLAN power sequencing on
nereid:
- If the EN pin GPP_B11 is not high during cold boot, the SoC gets stuck
in S3.
- During warm reboot, if we only assert RST without pulling the power
low, then the kernel crashes.
As a workaround while we investigate these issues, we pull the EN high
in S5, then actively drive it low in bootblock and high in romstage to
make sure it goes low during warm reboot.
BUG=b:227694137, b:225261075
TEST=Cold boot succeeds, and there's no kernel crash during warm reboot.
Change-Id: I1ca46d9649eff3f96a0e77db594d87288b29a83a
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
BUG=None
TEST=evtest works:
Select the device event number [0-14]: 9
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 1
Properties:
Testing ... (interrupt to exit)
Event: time 1649153020.275201, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649153020.275201, -------------- SYN_REPORT ------------
Event: time 1649153025.848689, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1649153025.848689, -------------- SYN_REPORT ------------
Event: time 1649153028.383195, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649153028.383195, -------------- SYN_REPORT ------------
Event: time 1649153080.869155, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1649153080.869155, -------------- SYN_REPORT ------------
Change-Id: I0d5134737fc758a43e1fff95e9f2a20200991bb1
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Some bytes in the descriptor need to be set differently for Type-C and
HDMI. To allow using a single firmware variant for both cases, update
the descriptor at runtime based on fw_config. This is a temporary
workaround while we find a better solution.
The byte values were determined by changing the following CSE strap and
comparing the generated descriptors:
Type-C: TypeCPort2Config = "No Thunderbolt"
HDMI: TypeCPort2Config = "DP Fixed Connection"
The default value before updating the descriptor is Type-C, but this was
chosen arbitrarily.
BUG=b:226848617
TEST=Type-C and HDMI both work on nereid with fw_config set correctly.
Change-Id: I2cc230e3bd35816c81989ae7e01df5d2c152062e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
Setting the clock source depends on clock request pin for WLAN/SD/SSD
device. Also turn off the unused (CLKREQ#3) clock sources.In skyrim,
clock source 0/1/2 are routed for WLAN/SD/SSD device.
BUG=b:227297986
BRANCH=none
TEST=Build
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I21fb912b69f59717eb4e84c379f706a0257a9ed1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The only purpose of mainboard_chromeos_acpi_generate()
was to pass cros_gpio array for ACPI \\OIPG package
generation.
Promote variant_cros_gpio() from baseboards to ChromeOS
declaration.
Change-Id: I5c2ac1dcea35f1f00dea401528404bc6ca0ab53c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The patch enables dynamic debug capability for Brya family of boards.
BRANCH=MAIN
BUG=b:153410586
TEST= Verified the CSE firmware update functionality on Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I51b0e0bb4392d3fbdb50577d3644491ab90a33c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
The hob finding functions are never looped over so there is no point
for the 'next' inside their name.
Change-Id: I18e452d313612ba14edda479d43f2797f6c84034
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This field was never meant to be filled out by coreboot, because it
can't know what the right value for this will be by the time the OS
is running, so anything coreboot could fill in here is premature.
This field is only read by the chromeos-specific `crossystem` utility,
not by kernel code, so if one does not run through depthcharge there'll
be many more broken assumptions in CNVS anyway.
Change-Id: Ia56b3a3fc82f1b8247a6ee512fe960e9d3d87585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Motivation is to have mainboard_chromeos_acpi_generate()
do nothing else than fill ACPI \OIPG package.
Change-Id: I3cb95268424dc27f8c1e26b3d34eff1a7b8eab7f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The value at offset 329 should be:
0x4B -> "K" not 0x48 -> "H" in ASCII code.
BUG=b:224884904
TEST=Build, confirm the part number is matched the corresponding parts
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I35dc5f036a29cdf4763389b6425df99ff63bbfa0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
K4U6E3S4AB-MGCL and K4UBE3D4AB-MGCL require special SPD files. This
commit overrides the default SPD files used for these parts
BUG=b:224884904
TEST=Verified that Dewatt SKU1 and SKU3 boot with changes
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: Ibd08f109765933640ea3d0ad442873c30fa14bc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Tune I2C parameters to make sure I2C1 and I2C7 bus speed is around 1MHz.
BUG=b:207333035
BRANCH=none
TEST=built and verified adjusted I2C speed around 1MHz
Change-Id: I09a9edf723bb1198bbf5d71248abc07276cd94ff
Signed-off-by: Eddy Lu <eddylu@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63241
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Use dedicated ALERT pin to resolve NO_RESPONSE error/status while
getting target configuration.
* Configure the ESPI to operate at 16 MHZ since operating at 33 MHz
causes boot stall.
BUG=b:226635441
TEST=Build and Boot to OS in Skyrim. Ensure that EC <-> AP communication
is working fine through Host Command debug logs in EC console, ectool
version command.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I951afdada8ee4f917cdeba8e287e5a2ae77c97ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63286
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found an issue where emmc and sd clocks were being misconfigured due
to using incorrect integer values when called instead of the defined
enums. Fixing by splitting the clock_configure_sdcc() function into
two (sdcc1 and sdcc2) as there was no commonality between the two
cases anyway. As a result, we can also get rid of the clk_sdcc enum.
BUG=b:198627043
BRANCH=None
TEST=build herobrine image and test in conjunction with CB:63289
make sure assert is not thrown.
Change-Id: I68f9167499ede057922135623a4b04202f4da9b5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
elog_gsmi_cb_mainboard_log_wake_source is called from SMI and causes
eSPI transactions. If the SMI interrupts an ongoing eSPI transaction
from the OS it will conflict and cause failures. Removing this call to
avoid conflicts. This can be re-enabled after refactoring
google_chromeec_get_mask to use ACPI MMIO.
BUG=b:227163985
BRANCH=gubyrush
TEST=No 164 errors detected during suspend_stress_test
/sys/firmware/log output after resume before change:
SMI# #1
ELOG: Event(B0) added with size 9 at 2022-03-31 19:52:51 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:52:51 UTC
Chrome EC: clear events_b mask to 0x0000000000000000
after change:
SMI# #6
ELOG: Event(B0) added with size 9 at 2022-03-31 19:50:19 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:50:19 UTC
Change-Id: I3320e3fb8bd9e9e0db84332e1d147a0af25f7601
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63280
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:226848617
TEST=HDMI works on nereid
Cq-Depend: chrome-internal:4650256
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I6a90d3d86b32f73ec0130e582539d1c5b045da62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
BUG=b:226848617
TEST=HDMI works on nereid
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I039c30f95d959dba489b24b6938d08da937c5e03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add support for ELAN trackpad on I2C0 bus.
BUG=None
TEST=Build and boot to OS in Skyrim. Perform evtest on Elan trackpad.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia1522af3f35ef131dda74c4aabecc4fa532dfbec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Turn off the NFC power which is controlled by GPP_D3 to save power in
S0ix states. For an USB device, the S0ix hook is needed for the on/off
operations to take place.
BUG=b:202737385
BRANCH=firmware-brya-14505.B
TEST=measure the voltage of GPP_D3 in S0ix states
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I69588c82dfde1744c45c7aff3ac05b80bb16a8f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
We set T3 as 300ms to meet Elan's spec, but the resume/suspend times
are greater than 500ms, which is the spec for Chromebooks.
The actual kernel timing has been measured, and given the ACPI delay
after deasserting reset in addition to the delay until the kernel
driver accesses the device, delaying only 200ms in the ACPI method is
also sufficient to meet the 300ms requirement.
BUG=b:223936777
BRANCH=none
TEST=build and test touchscreen function on DUT.
TEST=suspend, wake DUT and check touchscreen function.
Change-Id: I6b04cf6392d924aed01ca36b720f889b88d92311
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
C0 has no redriver, so enable SBU muxing in the SoC.
C1 has a redriver which does SBU muxing, so disable SBU muxing in the
SoC. However, this also disables AUX biasing when the pins are
configured as NF6. So instead configure the C1 AUX bias pins as GPO.
BUG=b:227259673
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: Ic0af662ecc1c6cee15b4ae98cb02deeefc93a71e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
Based on the latest schematic, agah will replace the Maxim 98390
speaker amps with Maxim max98360. This patch updates the
devicetree entries to reflect that.
BUG=b:210970640
BRANCH=brya
TEST=emerge-draco coreboot
Change-Id: I7ea36d276f7ffeae1510483027092e2bc59690fc
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:210970640
TEST=emerge-draco coreboot
Change-Id: I881c2c1ad7b0d10b7ae38fcd9814f757cf56feb5
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Brask set GPP_D0 to GPO in commit b0769db4, but Kinox doesn't support
fingerprint. This patch sets GPP_D0 to NC for matching schematic.
BUG=b:214025396
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I38b9eb2df83cfbdb58d95cb178c1d767299aa4da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
RF team comfirmed that SAR sensor is not necessary for MP,
therefore remove the corresponding entries from the devicetree.
BUG=b:202978964
TEST=Build pass.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I31faf18563848f8d6787fe70bfb28006efea8427
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Fill in the memory config based on the the schematic by bernadino 14 adl-p 20220112.pdf
BUG=b:219891328
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I981d2cd6feafee8c10ec9724a3dec9a23ba0ddd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 65aaccda5910e9c74aaa2a44ea84119d9476c902.
Reason:
1. Fix firmware messages show [ERROR] dw_i2c:invalid bus speed 390000
2. Measure DVT I2C3 speed < 400KHz.
BUG=b:215095284
TEST=There isn't ERROR messages and verify I2C3 speed < 400KHz.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I5982c82a55710824692b41e263418e4b4d420b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
We are using the second SPI pads for eSPI.
BUG=b:226635441
TEST=Build skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I43713d7376a28ced2be635668836464ceec46392
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63096
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the specific SPD hex file for the Samsung memory part with
updating the part number into the SPD table. The ABL needs to
identify the part by checking SPD data to do the proper tuning.
BUG=b:224884904
TEST=Build, validate the SPD data has been applied.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ia54726ce8c1bae46dcd4fed3df509ef184914e94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
init overridetree.cb based on the schematic bernadino 14 adl-p 20220112.pdf
BUG=b:226315394
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: Ibca9d93a81469730e472a645c607a97a624e9a1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update the GPP_D12 according to USB_C3_LSX_RX.
BUG=b:225081954
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
The device can be recognized when it is attached in port3.
localhost /sys/bus/thunderbolt/devices # ls
0-0 1-0 1-0:3.1 1-3 domain0 domain1
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I38caa76c855e683eb0587eb67ee9abc91af4545d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add override device tree for dojo and add PCIe domain support.
Reference:
- MT8195 Register Map V0.3-2, Chapter 3.18 PCIe controller (Page 1250)
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ifb02960504177fe488e6784b954c16b2c8d94972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add thermal table settings for tarlo which shares the same firmware with
taeko
BUG=b:215033683
TEST=emerge-brya coreboot
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I37f79cde502115bbf65bb97216eddb6ea22b1648
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
We don't want to enable the speaker on init. It will be enabled while
using GPIO AMP codec in depthcharge.
BUG=b:223289882
TEST=boot guybrush and verify the devbeep and gpio value in kernel
Change-Id: Ic949cc95556913a2afef4a683a49eaa1e07e6147
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Move WWAN power on sequence from OS to coreboot. This can save the
WWAN initial time about 10S. Another purpose is power resource be
removed because we don't power off the LTE in S0ix.
BUG=b:223490884
TEST=FM101-GL work as expected.
Enumerate time from
[ 17.747145] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 17.760192] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04
[ 17.760210] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.760215] usb 4-2: Product: Fibocom FM101-GL Module
[ 17.760220] usb 4-2: Manufacturer: Fibocom Wireless Inc.
[ 17.760224] usb 4-2: SerialNumber: 9c88998f
to
[ 3.936409] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 3.966695] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04
[ 3.989989] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.003813] usb 4-2: Product: Fibocom FM101-GL Module
[ 4.019760] usb 4-2: Manufacturer: Fibocom Wireless Inc.
[ 4.019762] usb 4-2: SerialNumber: 9c88998f
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0f3fe999ae3a109b739629948b619a389a9059b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Follow the Moli GPIO Table_20220324.xlsx to update it.
1.Set A15 as the default value.
2.Set A14, A19 NC.
3.Set C3, C4 as the default value.
4.Set D9 as the default value.
5.Set E5, E13 as the default value.
6.Set R4, R5 as the default value.
7.Update E14.
8.Set E12 as the default value.
9.Set D16 as the default value.
BUG=b:220821454
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Ia54256244111a99cb130b74f78c37815099a021a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
While adding this train of patches to program the dGPU power sequences,
I noticed some of the GPU GPIOs are incorrectly programmed in ramstage,
so this patch fixes the settings.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I622b1f5cfba84727bb31792358ca4162c7fa9f52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
AMD SDLE testing had been done and apply the following telemetry settings for dewatt EVT:
vdd scale: 91288
vdd offset: 279
soc scale: 29785
soc offset: 461
BUG=b:219626910
TEST=1. emerge-guybrush coreboot
2. pass AMD SDLE test
Change-Id: I4456ffddbf9963f1202a349abe52df2bbb726468
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63136
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ESPI is not initialized in PSP. Hence any attempt to write to port80
causes failure to boot. Disable PSP postcodes for now and re-enable it
later after ESPI is initialized in PSP.
BUG=b:224618411
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I73b7ddec50936f7836f915f459ca0bdc0777cb22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should be
delayed 100ms (TPVPERL) for the power and clock to become stable.
Instead of asserting PERST# right before PCIe initialization and waiting
for 100ms, which is currently the only function of 'mtk_pcie_pre_init',
so that the extra 100ms delay in ramstage is avoided.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Id5b9369e6f8599f93415588ea585c952a41c5e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Configure GPIO according to b:224107199 comment#15.
- GPP_E19 from NF to NC.
BUG=b:224107199
TEST=emerge-brya coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I06d02c5a8b6cf65d5643eaf30fb277c3321dac8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
The Cherry follower projects may choose Max98390 for audio output
so we have to add a new config CHERRY_USE_MAX98390. Also, the
'dojo' device is the first one to use it.
BUG=b:204391159
BRANCH=cherry
TEST=emerge-cherry coreboot
TEST=Verify beep function through CLI in depthcharge successfully
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Change-Id: I9b6bc5a5520292dd502b0389217f5062479b4490
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63083
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will setup the eSPI GPIOs in bootblock right before eSPI init.
BUG=b:226635441
TEST=build skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ff32bf840aa4b757e98d876cbd4e2ba15a760da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The eSPI CS function only exists on AGPIO30.
We will need to rework all boards to make eSPI function.
I also fixed the comments on the other eSPI pins.
BUG=b:226635441
TEST=Build skyrim
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib03c0a7dcad31d10dd4bad0d10a0184ab84aef9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add Skyrim DXIO descriptors using info from AMD and skyrim bouard
shematics.
BUG=b:225179599
TEST=Boots to OS on Skyrim Board
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Ib68cf3d64641b006e0f2c4805af22b44a505a0d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
