| Age | Commit message (Collapse) | Author |
|---|
|
SKU1A C0 has no redriver, so enable SBU muxing in the SoC.
BUG=b:283044004
BRANCH=none
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: I18b4ade2c60c270855fb2e733a9201539e08d8ba
Signed-off-by: mike <mike5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Enabling BT for screebo project
BUG=b:278169273
TEST=Check whether BT can connect to Bluetooth device
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Change-Id: I0ecd62abfbe751e1036948b1490844e7e63d7f0d
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75352
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
BUG=b:282912666
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Iee6a9026a4d210407350bfb7ecc8a058e7ff5c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
TEST=set the corresponding cbi bit, and saw SPI0 under sysfs
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I7099cde14cff90ad63e9164769f9913a8284a805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
BUG=b:278156430
TEST=verify the fingerprint on screebo
Change-Id: I986e470b28145f7b17427e794055929a4283c721
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75287
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch enables stylus support by configuring the "GPP_D08" irqs for
rex SoC. This allows the SoC to detect a stylus device, when in use.
However stylus is not a wake up source for the rex.
BUG=b:282256460
Test=Stylus is detected on proto1 device.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I84a71aa664698e105b738f8680d0a4751ca1fc72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch adds support for variant specific chip config update similar
to commit 061a93f93d2 ("mb/google/brya: Add variant specific soc chip config update").
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I60a4042cba608fd527527af9340ec0215f3086ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75046
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
add initial devicetree config for screebo
BUG=b:276814951
TEST=emerge-rex coreboot
Change-Id: Ie64d0e50ec22b3e363597af64eb723ef1f86dfa8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:278022971
TEST=verified on screebo
Change-Id: I16f1d66ca7f885120358eb2a2d3c6fb111319f11
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75173
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Denote the correct value of ACPI _PLD for USB ports.
The horizontal position of port C0 is incorrectly labelled.
+----------------+
| |
| Screen |
| |
+----------------+
C0 | | A0
| | C1
| |
+----------------+
BUG=b:216490477
TEST=emerg-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id9ed435ca0af131e3bb4538701fc97d78146899f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74366
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add DDR DQ map config for screebo
BUG=b:276814951,b:272218757
TEST=emerge-rex coreboot
Change-Id: I993ae4024689b9cedbea247689a760bd83cd0d45
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74961
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Generate RAM IDs for -
MT62F512M32D2DR-031 WT:B (LP5)
H9JCNNNBK3MLYR-N6E (LP5)
MT62F1G32D2DS-026 WT:B(LP5x)
H58G56BK7BX068 (LP5X)
BUG=b:276814951
TEST=Run part_id_gen tool without any errors
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I0fb2e488c06ed74d3fd493e5ca0ab89a825a9349
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74802
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
add the initial gpio configuration for screebo initial variant
BUG=b:276814951
TEST=emerge-rex coreboot
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Change-Id: Ib96e03f47bc1d6e5628ae459c3e1eb4dc18849c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74475
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch adds new USB_DB FW_CONFIG to enable support for USB4 ANX7452
Rev 2.
BUG=b:279647370
TEST=Able to build and boot google/rex with Proto 2 SKU
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I878b591e5919d05d3c5fc2eefdeb492e95d4f7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Set the `SOC_INTEL_CSE_SEND_EOP_ASYNC' flag to request End-Of-Post
right after PCI enumeration and handle the command response at
`BS_PAYLOAD_BOOT'.
With these settings we have observed a boot time reduction of about
100ms on google/rex.
TEST=Tests on google/rex with `SOC_INTEL_CSE_SEND_EOP_ASYNC' show
End-Of-Post after PCI initialization and EOP message received at
`BS_PAYLOAD_BOOT'.
Change-Id: I27b540eeddcada521eba91fcc51504831d6dc855
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Change-Id: Ie75ce1eee3179a623da812a6b76c7ec457684177
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch enables all DDI ports on Rex board to support display port
tunneling and dual display on TBT dock.
BUG=b:273901499
TEST=Boot google/rex and connect two displays over a TBT dock and check the display functionality.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I45ee5334fbb877bd58912c8d24920037f155dc42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74413
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the screebo variant of the rex0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:276814951
BRANCH=None
TEST=util/abuild/abuild -p none -t google/rex -x -a
make sure the build includes GOOGLE_SCREEBO
Change-Id: I8d05ca7c0fe596378ca15d0734d46ad1dc63a1f9
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74391
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
No need for variant to use _weak.
BUG=b:276818954
TEST=new_variant_fulltest.sh rex0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I7ad904e06e5d83edf4bc11cafd5060ca409bd4ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74294
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add DTT thermal settings for thermal control provided by
thermal team for rex0 board
BRANCH=None
BUG=b:262498724, b:270664854
TEST=Built and verified thermal entries in ACPI SSDT on Rex board
Change-Id: I00dd97b759c8c68edaeeb4d64422b83c5e86981d
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the Rex debug flash layout to optimize WP_RO to 4MB.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Increase to 7.5MB.
RW_LEGACY: Introduce with 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 2MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot google/rex with FSP release and debug image.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4ab69eb24937d58c8bc5d3c0a6e5cb70b843a1ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the Rex flash layout to optimize WP_RO to 4MB.
The idea is to create more space inside FW_RW_A/B to accommodate
multiple blobs to boot google/rex with different Intel MTL SoC stepping.
Changes for chromeos.fmd:
SI_BIOS:
RW_SECTION_A/B: Reduce to 7MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Increased to 1MB.
RW_UNUSED: 3MB (reserved)
WP_RO: Reduce to 4MB
Additionally, ensure RW_SECTION_B region starts at 16MB boundary in the
SPI Flash.
BUG=b:277143384
TEST=Able to build and boot google/rex with FSP release and debug image.
Change-Id: Iccf83b7bb66d0d5503e0ff9e9a819051296c6724
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74229
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables pre-cpu boot timestamps from cse.
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 47,000
945:CSE started to handle ICC configuration 225,000 (178,000)
946:CSE sent 'Host BIOS Prep Done' to PMC 225,000 (0)
947:CSE received 'CPU Reset Done Ack sent' from PMC 516,000 (291,000)
991:Die Management Unit (DMU) load completed 587,000 (71,000)
0:1st timestamp 597,427 (10,427)
BUG=b:259366109
TEST=Boot on rex, check "cbmem -t"
Change-Id: I68cd53c18af6a400bcd9dc15d428a904b0647495
Signed-off-by: Bora Guvendik <bora.guvendik@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73759
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch avoids creating runtime ACPI for unused WIFI solutions.
For example: if the Rex SKU is with WIFI_CNVI then you don't need
to populate ACPI code for WIFI_PCIE.
FW_CONIG can be used for making those decisions.
TEST=No ASL entries being created for WIFI_PCIE if the FW_CONIG is
set to WIFI_CNVI.
Also, helped to save the boot time on google/rex (FSP-S API) by 9ms.
Change-Id: I60e4332d8d8c360fdf425b30513ff79209979e85
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74147
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch adds FW_CONFIG to accommodate different Rex BoM
components across various SKUs.
1. Fingerprint sensor - FP Present/Absent
2. Ultra wideband - UWB Absent/Using BITBANG/Using GSPI1
3. WIFI - CNVi/PCIe
TEST=Able to build and boot google/rex.
Change-Id: I97b0dc25f239103a0a235f14b50008a633e2f88d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
This patch updates the Rex flash layout to allow CSE Lite FW
update and accommodate multiple ESx SoC stepping blobs.
For default chromeos.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.9MB.
RW_LEGACY: Reduce to 1MB.
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
Additionally, moved RW_LEGACY under extended BIOS region.
For chromeos-debug-fsp.fmd
SI_BIOS:
RW_SECTION_A/B: Increased by ~1.2MB.
RW_LEGACY: Dropped
RW_MISC: Reduce to 152KB.
- Drop RW_SPD_CACHE
- Optimize other sections
BUG=b:262868089
TEST=Able to enable CSE update on google/rex and have free space
to add one more PUNIT FW for support different SoC stepping.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6146b36c4ce2c0141277eeb906d6ad1f503f3c78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Debug FSP is ~920KiB larger than release FSP and we don't have
sufficient space for rex flash layout.
Remove RW_LEGACY and split them into RW_SECTION_A/B so we can have a
room for it.
Note: This fmd will only used for internal testing/debugging and not for
the firmware in released devices.
BUG=b:262868089
TEST=Build google/rex with CONFIG_BUILDING_WITH_DEBUG_FSP.
Change-Id: I58b0af9c43c5d096dc80084497b39f13f67c25cd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This reverts commit 555ceca38a78 ("mb/google/rex: Enable VPU").
Reason: Unable to boot to latest OS image with VPU enabled.
BUG=none
TEST=Boot to OS image 15376 on google/rex
Change-Id: If61282528922304373d492b362056b52995cbcad
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paz Zcharya <pazz@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add GOOGLE_SMBIOS_MAINBOARD_VERSION flag for rex board.
BUG=None
TEST=Verfied board ID for rex using "crossystem" command, giving the
output as 1.
Without CL:
localhost ~ # crossystem
arch = x86 # [RO/str] Platform architecture
backup_nvram_request = 1 # [RW/int] Backup the nvram somewh
battery_cutoff_request = 0 # [RW/int] Cut off battery and shu
block_devmode = 0 # [RW/int] Block all use of develo
board_id = (error) # [RO/int] Board hardware revision
clear_tpm_owner_done = 0 # [RW/int] Clear TPM owner done
With CL:
localhost ~ # crossystem
arch = x86 # [RO/str] Platform architecture
backup_nvram_request = 1 # [RW/int] Backup the nvram somewh
battery_cutoff_request = 0 # [RW/int] Cut off battery and shu
block_devmode = 0 # [RW/int] Block all use of develo
board_id = 1 # [RO/int] Board hardware revision
clear_tpm_owner_done = 0 # [RW/int] Clear TPM owner done
Signed-off-by: Jay Patel <jay2.patel@intel.com>
Change-Id: I644ed7a948f0094a0be080153d83eaa2e37b8f1f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74037
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch drops the UFC sensor OV2740 (reused from the Brya chassis)
support for Rex and added support for Rex specific UFC sensor HI-556W.
BUG=b:269499723
TEST=Verified UFC is working on google/rex Proto 1.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6b8ac08adec351a103ac1764d974db4881dc4d6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70225
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add enable_gpio for USB power resource
BUG=b:273891168
TEST=Able to detect USB CAM
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I08ebe560c8b75c8b590c889b7b90dbe678318d2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Align project style with other chrome projects.
TEST=built FW not changed
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Icfd1d274216d387cab6feb68afa49fc63c8c52e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Rex uses GL9755 and miss select the driver.
BUG=b:273906526
TEST=SD card is functional.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I674b052689c80873e8a3b295d15788f3a93f0b82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch increases FW_CONFIG for USB_DB to 3-bits.
BUG=b:273346973
TEST=Able to build and boot google/rex with Proto 2 SKU
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib07ba1d54e7f7e2b09a99438529e503d9c9edb7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that the driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:268607999
TEST=Build and boot rex proto1 to OS and verify privacy LED behavior.
Change-Id: Ife849f7407b02867ddb992d7eebb08b0b44aecc8
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kiran2 Kumar <kiran2.kumar@intel.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Touchscreen signals were renamed for Rex schematics dated 21st Dec'22.
This CL fixes the comments for those signals.
BUG=b:263411413
TEST=None required (changed comments only)
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Ic40ef943d199d9f4a2bec9c0e6d4820224ef6adc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=b:270529665
TEST=Verify the build and boot on Rex board
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I0e3d3312c546a2a468fb906a08b8d3ec3e96c46a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add the support LP5 RAM parts for rex:
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 3 (0011)
BUG=b:270708359
TEST=emerge-rex coreboot
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Id0925ccec014c9c535178ed3d908e60889df624d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add the support LP5 RAM parts for rex:
DRAM Part Name ID to assign
H58G56BK7BX068 1 (0001)
BUG=b:270708359
TEST=emerge-rex coreboot
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I9eea7e277628992be9b7768a678a50425444002a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Remove `fixme` from gpio.h since it has been addressed.
BUG=none
TEST=Only a cosmetic change
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I79a2493dba6becd4b8c1ebf37e452a5a173eb396
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Define some actions based on probe results for audio:
- Disable the SoundWire GPIOs when I2S option is selected.
- Disable the I2S GPIOs when SoundWire option is selected.
- Disable all the GPIOs when no audio is enabled.
BUG=b:269497731
TEST=Test that GPIOs are configured based on the current
value of the fw_config field in cbi.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I0ed452a0d08e6779add318d9bbd1e97b50b6aea9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In order to improve gpio merge mechanism. Change iteration override
to padbased table override. And the following patch will change fw
config override with ramstage gpio table override.
Port of commit 7aef2b1294f2 ("mb/google/nissa: Apply gpio padbased
table override")
BUG=none
TEST=Verify devbeep at depthcharge console
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I2ee86bbec7d25a35d726f29ad79891f1054bf52c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73182
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch makes EC wake up AP from s3/s0ix for OS shutdown/hibernate
when the state of charge drops to low_battery_shutdown_percent.
BUG=b:255465618
TEST=emerge-nissa chromeos-bootimage (EC: https://crrev.com/c/4243898)
Verify system resumes from s0ix and then enter S5 on nivviks with steps:
1. disconnect AC
2. powerd_dbus_suspend --disable_dark_resume=false
3. fakebatt 5
4. fakebatt 4
Change-Id: I63b5246432687e38ddfc5733ac3a115c3456d7e9
Signed-off-by: Ivan Chen <yulunchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73082
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
This patch marks unused USB ports (USB2.0/TCSS) empty to avoid
prompting wrong dmesg as below.
```
usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
```
Mainboard variants to override the USB ports as per the target
board design.
TEST=Able to build and boot google/rex with all USB ports are
working as expected.
Change-Id: Ic3d21151a22f2318413f480f3386bf2dbf696307
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch overrides `SkipExtGfxScan` UPD as the Rex device is
equipped with an on-board graphics device hence, skip scanning
external GFX devices.
BUG=b:228002764
TEST=Able to save ~1ms+ boot time on google/rex.
FSP FPDT Data is showing the timestamp between those function calls.
Without this patch:
[INFO ] CheckOffboardPcieVga/5b7cc220-e183-481c-87f427a92d8db88f -> 979684 -> 22
[INFO ] CheckOffboardPcieVga/5b7cc220-e183-481c-87f427a92d8db88f -> 980815 -> 1131
With this patch:
`CheckOffboardPcieVga` is not getting called.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I20aa09e80671ab94e639787f40b95b740bbe5efb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch drops the WFC sensor OV8856 (reused from the Brya chassis)
support for Rex and added support for Rex specific UFC sensor OV13B10.
BUG=b:267264348
TEST=WFC MIPI cameras have been enabled using google/rex Proto 1.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic785b82db4368f40d91921f29c218cf417938541
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70226
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Enabling `SaGv` along with FSP v2473 is causing blank display issue.
Mostly likely we shouldn't enable SaGv yet on Intel MeteorLake.
BUG=b:267446159
TEST=Able to see ChromeOS UI in consecutive boot.
This reverts commit cbca81c5946384843197c08401c4266f45fef4a2.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ifbcc36515f7550c183c40e5af94684f5c3e39a7a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72774
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Removed workaround since the latest schematics fixed.
Power Sequencing of ELAN6918 (in ACPI) after this patch
`POWER enabled -> RESET deasserted -> Report EN enabled`
BUG=b:247029304
TEST=Verified ELAN touch panel is working as expected after booting
Google/rex device to ChromeOS.
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I19629262776f7e0cccbdebb2285890d177a8a8a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72725
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch overrides `SaGv` FSP-M UPD to enable SaGv feature to be
able to train memory (DIMM) at different frequencies.
On all latest Intel based platforms SaGv is expected to be enabled
to support dynamic switching of memory operating frequency.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7cf52b966c1355c1f2bd4ae7c256fa4252a90666
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
Introduce at new config option CONFIG_FSP_PUBLISH_MBP_HOB to
control the creation of ME_BIOS_PAYLOAD_HOB (MBP HOB) by FSP.
This new option is hooked with `SkipMbpHob` UPD and is always
disabled for ChromeOS platforms.
This made skip_mbp_hob SOC chip config variable redundant
which is also removed as part of this change.
BUG=none
TEST=Build and boot to Google/Rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Iaba1ea29a92a63d2b287e1ccdea1a81ec07b9971
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO.
Previously, we flagged as an error any device which set the
'has_power_resource' flag but did not set 'disable_gpio_export_in_crs.'
There's no reason to require explicit disablement however, so drop the
superfluous 'disable' flag, and change the _CRS generation to check if
the GPIOs will be exported via the 'has_power_resource' flag instead.
BUG=b:265055477
TEST=build/boot skyrim, dump SSDT and verify touchscreen GPIOs only
listed under PRx, not under _CRS.
Change-Id: I837ae6c6fe4b8e1c4e10686406cba06bdb7759d2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This patch disables the stage cache to save boot time.
Note: S3 is not POR for Intel MTL mobile skus.
Boot time is reduced by ~8ms.
Boot time before:
4:end of romstage 1,391,225 (13,724)
100:start of postcar 1,403,339 (12,114)
Boot time after:
4:end of romstage 1,380,262 (5,618)
100:start of postcar 1,392,323 (12,060)
Change-Id: I9775fc628f345a514894f30435a374e2ffa057c1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch configures GPP_H15 (EN_DMIC_SOC_DATA) as GPO and put into
safe state aka LOW/PD.
BUG=b:263411621
TEST=Able to build and boot Google, Rex to ChromeOS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3d376f895b2f0882c9fa6fe7b98686907bde4321
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71631
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the USB2-C1 mapping from USB2 Port 4 to USB2 Port 1
as per latest Rex schematics dated 12/06/2022.
TEST=Hardward awaited.
Change-Id: Ifc82200e6eafcea7e820a96df81325f3c8849fd1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70426
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DCI interface deprecated for Proto1. USB2_8 port becomes no-connect.
BUG=b:263494661
TEST=Able to build and boot Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6f03d600acd8ceaa5a5630fc19c1c7e34a4ea28f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71237
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Rename DB_USB4 for KB8010 while adding ANX7452 as different
DB_USB4 option.
2. Add audio component for Soundwire.
3. Rename MAX98357_ALC5682I_I2S to MAX98360_ALC5682I_I2S.
Change-Id: I9f04c644b8a392feb2609f906bc9db945bf5fce2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70867
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to build and boot Google/Rex.
Device (PMC)
{
Name (_HID, "INTC1026") // _HID: Hardware ID
Name (_DDN, "Intel(R) Meteor Lake IPC Controller") // _DDN: DOS Dev
ice Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0B)
}
...
}
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I28c0153a770b36cde0653ac92d2e5ad1b8dd3449
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71268
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTF functionality for Meteor Lake Rex board.
BUG=b:262498724
TEST=Booted to OS and verified DPTF entries in ACPI SSDT on Rex board.
Change-Id: I87b2d71650be9ce940d9452bf4a76d4cd1ddba52
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70884
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:263413949
TEST=Able to build and boot Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I453fe8e1f4b4b8d4730ade259899d76aec949a44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71231
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
BUG=b:263412235
TEST=Able to build and boot Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia444cc8e3666fe15479ece81d068f9e8f1d339ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71228
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch connects USB3_PCH_*_WWAN_* to USB32_2 as per Proto 1
schematics dated 12/14/2022.
TEST=Able to build Google/Rex.
Change-Id: Ie04c79ff5c231527e3d5f63a5cc553ec39c46914
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch updates the GPIO PIN name as per Proto 1 schematics dated
12/14/2022.
TEST=Not code change, just updated the comment section.
Change-Id: Ic076ab35689fd2afb7c18eff065a90b9464a6b1d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70747
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
BUG=none
TEST=Build and boot to the OS on google/rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I2c5bac880e7dbc2ec14376c5cee3c13363bab377
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70444
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures to be able to drive SYS_SLP_S0IX_L `low` based
on the state of the system while `SLP_S0_L` signal is `low` (while
the system is in S0ix).
Implemented runtime ASL method (MS0X) being called by PEPD device
_DSM to configure `SLP_S0_GATE (GPP_H14)` PIN at S0ix entry/exit.
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One))
{
\_SB.PCI0.CTXS (0x75)
}
Else
{
\_SB.PCI0.STXS (0x75)
}
}
BUG=b:256807255
TEST=Able to see SYS_SLP_S0IX_L goes low in S0ix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie6b5e066f228ea5dc79ae14dd803fc283fd248ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70196
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables S0ix for Google/Rex platform.
BUG=b:256807255
TEST=Able to program FADT table Bit 21 (Low Power Idle S0)
Change-Id: I79546267d29622c65321f7dfa29d3aac2fa59438
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70430
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch generates the following for the mainboard:
Scope (\_SB)
{
Method (MPTS, 1, Serialized)
{
Local0 = \_SB.PCI0.RP06.RTD3._STA ()
If ((Local0 == One))
{
\_SB.PCI0.RP06.PXSX.DPTS (Arg0)
}
}
}
Change-Id: I27ade63cfe0586aee9f03ba816b2590f14dcb610
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70229
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds PCIe based SD controller at RP 7 (from RP 11) with
Proto 1 schematics dated 11/30.
Additionally, added the RTD3 entries for the SD controller.
Finally, ensured that EN_PP3300_SD (GPP_D03) is configured in
bootblock and SD_PERST_L (GPP_D02) is configured in romstage to
meet the power cycle requirement.
BUG=b:242917011
TEST=Able to build and boot Google/Rex. SD card detection is due
for the Proto 1 hardware.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I23d53e4d61ec36d2145f9e5816d97d13eb5b219e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70064
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
This patch drops the usage of reading `board_id()` while performing
the GPIO configuration.
The reason to drop the board_id check is to ensure that GPIO
configuration for MLB (mainboard) would remain the same and the only
GPIO PIN configuration that differs would be due to usage of having
different DBs (daughter board) which will be taken care using
CBI (and fw_config.c file) in coreboot.
Additionally, drop unused early GPIO default configuration table.
BUG=b:260804656
TEST=Able to perform the GPIO configuration and able to boot
Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I96cafd1c904001cbf4199977e9e721afe5eab470
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Enable this feature, and it can use the probe statement in devicetree
to cache of fw_config field as oem string.
TEST=With CBI FW_CONFIG field set to 0x1561
localhost ~ # dmidecode -t 11
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: AUDIO-MAX98357_ALC5682I_I2S
String 2: CELLULAR-CELLULAR_PCIE
String 3: UFC-UFC_MIPI
String 4: WFC-WFC_MIPI
String 5: DB_SD-SD_GL9755S
Change-Id: I6cb35eb9c0fbe32764ca76bb7a929cc92fc38404
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70228
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SATA is not supported on google/rex hence disable it.
BUG=none
TEST=Build and boot to google/rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I35a742ab9782feed86c3af514505d870d181b34b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
`is_untrusted` is eventually ended up by adding DMA property _DSD which is similar to what `add_acpi_dma_property` does for WWAN drivers, hence it
makes sense to have a unified name across different device drivers.
BUG=b:259716145
TEST=Verified that the _DSD object is still present in the SSDT.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I4e0829a76a193b0a1e1e0f2b7ce2119bb00dd696
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69937
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adding cros_gpios for crossystem to access WP GPIO
BUG=b:258048687
TEST= run FAFT firmware_WriteProtect passed.
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: Ieac1df805c6399aefdc13aae136630d496aacd58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69924
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables the DisplayPort detection at preboot for Rex board.
BUG=b:247670186
TEST=Built image and validated DisplayPort feature at preboot on Rex.
Change-Id: I1a8a13e937c7132696aa39d85c3c6b6fb2dd13a5
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67742
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
EC_HOST_EVENT_USB_CHARGER is no longer defined by the EC, so remove all
references.
BUG=b:216485035,b:258126464
BRANCH=none
TEST=none
Change-Id: I9e3e0e9b45385766343489ae2d8fc43fb0954923
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch deselects `USE_PM_ACPI_TIMER` kconfig to ensure that
ACPI PM timer remains disabled.
The PM timer (by PMC IP) consumes more power and blocks S0ix so the
timer is emulated by ucode to save power and unblock S0ix.
TEST=Able to boot Google, Rex and ensure PMC MMIO register 0x18fc
BIT 1 is set.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2a23b417ff7fb6328323380a7df46b4b397fc8eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69685
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
None of the touchscreens (over I2C) used in the rex program requires
exporting GPIOs in the ACPI _CRS method.
This can cause i2c devices to malfunction or cause timing
sequence violations if ACPI exports a PowerResource for the
device that uses GPIOs that are also exported in _CRS.
BUG=none
TEST=Able to build and boot Google, Rex platform.
Without this patch:
[ERROR] I2C: 00:10: Exposing GPIOs in Power Resource and _CRS
With this patch:
None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I578a60eff27f94d6dc94b900604bc7560337d60b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69612
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will enable crossystem to access WP GPIO
BUG=b:258048687
TEST= wpsw_cur in crossystem reads the correct gpio
Change-Id: I67f4a57025064dbf8c691255b0abae9d3fa0dbd3
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69468
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Fingerprint SPI, and power-off FPMCU during romstage.
For reference see CL:66915 for a similar change to Brya's power sequence
SHA: 2b523ce6316e5c5ec86fe812d739fe48ca81d83d ("Invoke power cycle of
FPMCU on startup")
TEST=Tested on Rex - setup and logged in using fingerprint
Change-Id: I4e6be24e72a8232ae2c958a01cf8ea9a272d7365
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66992
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch enables the radio frequency interference mitigation for Rex.
BUG=b:248391777
TEST=Booted to OS on Rex board. Verified RFIM DSM is presented to kernel
through ACPI SSDT.
Change-Id: I22f9861452c2c222dd7a33bfeb02c63b026bf2f7
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fix fw_config probe for UFC and WFC.
BUG=b:255971791
TEST=Build Google Rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I5103e7da04004414d96f42057c105cf9fbf51b25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Rex board only uses TBT PCIe root ports 0 and 2. This change disables
rp1 and rp3 root ports.
BUG=b:254207628
TEST=Booted to OS and verified rp1 and rp3 root ports were disabled.
Change-Id: Ia5c1d657c0ad0482619d739f8949bc9168eac25b
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68854
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch moves DRIVERS_INTEL_USB4_RETIMER config from Meteor Lake
SoC to Rex mainboard to maintain the symmetry with previous
generation ChromeOS devices (Brya and Volteer).
BUG=none
TEST=Able to build and boot to Google/Rex with USB4 functionality
remaining intact.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I38360f6f1f2fcb4b0315de93c68f00d77e63003c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This change is to skip sending the MBP HOB since coreboot doesn't
use it and also helps to reduce the boot time by ~40 ms.
Boot time data
Before:
* 955:returning from FspSiliconInit 1,656,985 (274,416)
After:
* 955:returning from FspSiliconInit 1,593,036 (233,286)
BUG=b:252410202
TEST=Verified that boot time is reduced by ~40 msec.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I0d4f66940529b8d38d9658c769feba8b5c9b715e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68418
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add initial fw config as per config.star.
BUG=b:253199788, b:245158908, b:244113761, b:244012065
TEST=emerge-rex coreboot. Make sure that ACPI tables are equivalent
before and after this change with CBI.FW_CONFIG set to 0x1561.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I66f8b3e4ab414c03b8d63fdd31e0f3f424619340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68220
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:253199788
TEST=Build and boot to Google/Rex.
Change-Id: Ib729c98a4d67aa46992fdccf592010b0313605a6
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66817
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add CHROMEOS_WIFI_SAR to include the SAR configs.
2. Add get_wifi_sar_cbfs_file_name() that return the wifi SAR
filename.
BUG=none
TEST=emerge-rex coreboot
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia863eaa53c9456ae0e9f0e8914e0de497a32b53b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68393
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch enables PD Sync for Rex.
BUG=b:248775521
TEST=Able to boot Google/Rex with PD sync enabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I749b5dea481c7546579e97f923f143dd17f831d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67819
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
This patch de-selects EC software sync config and enable early
EC Software Sync.
BUG=b:248775521
TEST=Able to perform EC sync on Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6bf8018e8a3fd06bb98c82a27d12883fc8d3a5db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch adds ACPI configurations of 8MP YHUX and 2MP CJFKF28-1
as world- and user-facing cameras of Rex.
BUG=b:246413264
TEST=Verified world- and user-facing cameras using Chrome Camera App on
Google/rex device.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Iaaa16e491a66500606b3a9eb1d87f396641778e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch selects the SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES to allocate
TBT/USB4 root port resources for PCIe tunneling.
BUG=b:248328015
TEST=Built image and verified TBT/USB4 tunneling functions on Rex.
Change-Id: I69f4d26bb7b3d74dbda068add284a69f1bbeff40
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This reverts commit 1a8eb6c02103727431ac1ea23f4f507e49f3cde7.
Reason for revert: migrating to the 32MB AP Firmware hence, need to
revert this CL.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibea1ad0cff008f9391cbda9e51899557b1e9c979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add FM350GL 5G WWAN support using drivers/wwan/fm and additional PM
features from RTD3.
BUG=b:244077118
TEST=check cbmem -c
\_SB.PCI0.RP06: Enable RTD3 for PCI: 00:1c.5 (Intel PCIe Runtime D3)
\_SB.PCI0.RP06: Enable WWAN for PCI: 00:1c.5 (Fibocom FM-350-GL)
check PXSX Device is generated in ssdt.
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6114c589769d2eca882cf1a5255cf4c5937121a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
ELAN6918 Power Sequencing seems not perfectly matching
with the previous platforms and setting GPP_C06 to high prior
to the power sequencing is actually makes it work.
Ideally Power Sequencing should be as below for ELAN6918 (in ACPI)
`POWER enabled -> RESET deasserted -> Report EN enabled`
But below sequence is only working currently:
`Report EN enabled (ramstage) -> POWER enabled (ACPI) -> RESET
deasserted (ACPI)`
BUG=b:247029304
TEST=Verified ELAN touch panel is working as expected after booting
Google/rex device to ChromeOS.
Change-Id: Ideaeb0faa882b8e603534bbface51ea76923d436
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
TEST=Able to build and boot the Google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iae5317b24856ef2cbd2f36cc28f645826536c21a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
BUG=b:232573696
TEST=Able to verify audio playback on Google/Rex with this change.
Change-Id: Ia8dfc79e7e4d27828726145156c870733d716899
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66919
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Lists of GPIO PINS being updated:
SPKR_INT_L_R
RST_HP_L
SOC_HDMI_HPD_L
SOCHOT_ODL
SOC_FPMCU_INT_L
EN_PP3300_WLAN
BUG=b:24410269
TEST=Build and boot Google/Rex to ChromeOS.
Change-Id: If2fb354f931217c09a6c1c81ca780cb121b24468
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67449
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable touchpad for Google Rex.
BUG=b:245866939
TEST=Build and boot to Google Rex. Verify touchpad works.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I49fdd72bf3350085e82411b95edcd6a9a09d2df5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67471
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
|
|
Add GPE route for GPP_B.
BUG=b:245866939
TEST=Build and boot to Google Rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I28066a6cc75908f8ceefbdbf8c088c56833606ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The PCIe WWAN module used on rex requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WWAN_RST#, then WWAN_PERST# in ramstage
BUG=b:244077118
TEST=FM350 could be enumerated via lspci
Measured signals to check start-up Timing Sequence, tpr/ton1/ton2.
Tpr = 572mS
Ton1 = 6.3s
Ton2 = 6.3+4.17ms
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6cda9348ef7f54efe5ba2358040596a1c2da1b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67332
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
