Age | Commit message (Expand) | Author |
2019-09-11 | mb/google/hatch: Create dratini variant | Wisley Chen |
2019-09-10 | mb/google/hatch/variants/helios: Modify FPU power on sequence | Frank_Chu |
2019-09-09 | mb/google/hatch: Distinguish SKU1 and 2 for eMMC and SSD respectively | Peichao Wang |
2019-09-06 | mb/google/hatch/variants/helios: Update DPTF parameters and TDP PL1/PL2 | Frank_Chu |
2019-09-04 | mb/google/hatch/var/kindred: Update DPTF parameters and TDP PL1/PL2 | David Wu |
2019-09-03 | mb/google/hatch/var/kindred: Update DRAM IDs for 8G and 16G 3200 | David Wu |
2019-09-02 | mb/google/hatch/var/helios: Increase touchscreen reset delay to 120ms | Philip Chen |
2019-08-30 | mb/google/hatch: Add settings for noise mitgation | Dtrain Hsu |
2019-08-28 | mb/google/hatch/variants: Increase touchscreen reset delay to 120ms | Sumeet Pawnikar |
2019-08-28 | mb/google/hatch: Override DLL values for Kindred | Jamie Chen |
2019-08-23 | mb/google/hatch/var/kindred:: Add enable signal for touch screen | Philip Chen |
2019-08-23 | mb/google/hatch/variants/kindred: Remove unused devices | Philip Chen |
2019-08-21 | mb/google/kohaku: Correct DPTF temp sensor IDs | Seunghwan Kim |
2019-08-20 | mb/google/hatch: Skip SD card controller WP pin configuration from FSP | Aamir Bohra |
2019-08-20 | mb/google/kohaku: Use level trigger for touchscreen interrupt | Seunghwan Kim |
2019-08-16 | mb/google/hatch: Create Akemi variant | Peichao Wang |
2019-08-15 | mb/google/hatch/var/kindred: Configure GPIOs for eMMC SKUs | David Wu |
2019-08-15 | mb/google/hatch/var/kindred: Disable SATA controller for eMMC SKUs | David Wu |
2019-08-15 | mb/google/hatch/var/kindred: Configure GPIOs for SSD SKUs | David Wu |
2019-08-15 | mb/google/hatch/var/kindred: Disable eMMC for new SKU ID 23 and 24 | David Wu |
2019-08-13 | mb/google/hatch/var/kohaku: Change Atmel touchscreen HID to PRP0001 | Furquan Shaikh |
2019-08-13 | mb/google/hatch: Kohaku: Enable DMIC1 in device tree | Mac Chiang |
2019-08-11 | kohaku: add TEMP_SENSOR_3 and TEMP_SENSOR_4 to DPTF | Paul Fagerburg |
2019-08-11 | mb/google/hatch: Fix Kohaku pen GPIO configuration | Tim Wawrzynczak |
2019-08-09 | mb/google/hatch: Refactor override_early_gpio_table | Tim Wawrzynczak |
2019-08-07 | mb/google/hatch: Kohaku: Re-setup dual-routing of EMR_GARAGE_DET | Tim Wawrzynczak |
2019-08-07 | mb/google/hatch: Kohaku: Add touchscreen controller to device tree | Tim Wawrzynczak |
2019-08-07 | mb/google/kohaku: Enable stylus pen device | Seunghwan Kim |
2019-08-05 | mb/google/helios: Set SPKR_PA_EN PIN high for boot beep | Subrata Banik |
2019-08-03 | mb/google/hatch/variants/helios: Adjust all I2C CLK and I2C0 SDA hold time | Frank_Chu |
2019-08-03 | mb/google/hatch: Enable PmTimerDisabled config to reduce S0ix power usage | Subrata Banik |
2019-08-02 | mb/google/hatch: Fine-tune Kohaku I2C CLK frequency | Philip Chen |
2019-07-31 | mb/google/hatch: Initialize SSD GPIOs in bootblock | Shelley Chen |
2019-07-31 | mb/google/kohaku: Update DPTF parameters and TDP PL1/PL2 | Seunghwan Kim |
2019-07-31 | mb/google/hatch/variants/hatch: Set PCH Thermal Threshold value to 77 deg C | Sumeet Pawnikar |
2019-07-30 | mb/google/hatch: Enable chipset_lockdown coreboot config for hatch | Subrata Banik |
2019-07-26 | mb/google/hatch/helios: Update GPIO and device tree | Tim Wawrzynczak |
2019-07-23 | mb/google/hatch: Add FP MCU to helios device tree | Philip Chen |
2019-07-21 | mb/google/hatch: Remove hatch_whl | Philip Chen |
2019-07-21 | mb/google/hatch/var/kindred: Implement variant_devtree_update() | David Wu |
2019-07-21 | mb/google/hatch: expose get_board_sku() as global | David Wu |
2019-07-21 | mb/google/hatch: Add support for variant_devtree_update() | David Wu |
2019-07-19 | mb/google/hatch: Fix SD card is detected as read only issue | Subrata Banik |
2019-07-19 | mb/google/helios: Add ALC1011 in device tree to enable speaker amps | Sathya Prakash M R |
2019-07-18 | mb/google/hatch/var/helios: Implement variant_memory_sku() | Furquan Shaikh |
2019-07-18 | mb/google/hatch: Add support for variant_memory_sku() | Furquan Shaikh |
2019-07-18 | mb/google/hatch: Add FP MCU to kohaku device tree | Shelley Chen |
2019-07-18 | mb/google/hatch: Disable wireless charging | Subrata Banik |
2019-07-16 | mb/google/hatch: Disable Bluetooth in bootblock and enable in ramstage | Shelley Chen |
2019-07-13 | mb/google/hatch: Fix trackpad configuration in overridetree | Furquan Shaikh |
2019-07-11 | mb/google/hatch: Update AC/DC loadline values | Rizwan Qureshi |
2019-07-11 | mb/google/hatch/variants: Fix nonworking touch pad | Frank_Chu |
2019-07-11 | mb/google/hatch: Disable GPIO community dynamic clock gating | Tim Wawrzynczak |
2019-07-11 | mb/google/hatch: Fix interrupt trigger type for GPP_H0(HP_INT_L) | Furquan Shaikh |
2019-07-08 | mb/google/hatch: Set GPP_D9 as enable pin for Goodix Touch Screen and | Frank Wu |
2019-07-07 | mb/google/hatch: Update GPIO settings for SD card and SPI1 Chip select | Krishna Prasad Bhat |
2019-07-07 | mb/google/hatch/var/kindred: Add Raydium touchscreen support | David Wu |
2019-07-07 | mb/google/hatch/var/kindred: Update ELAN GPIO/IRQ and add Synaptics Touchpad | David Wu |
2019-07-07 | mb/google/hatch/variants/kindred: Enable eMMC support | David Wu |
2019-07-02 | mb/google/hatch: Set trackpad irq and wake to GPP_A21 | Shelley Chen |
2019-07-02 | mb/google/hatch: Add INVERT to all IOAPIC pads | Shelley Chen |
2019-06-28 | mb/google/kohaku: Correct trackpad i2c address | Seunghwan Kim |
2019-06-26 | mb/google/hatch: Add a GPIO to enable/disable FPMCU power | Philip Chen |
2019-06-26 | mb/google/hatch: Remove pulls on NC pads | Furquan Shaikh |
2019-06-26 | mb/google/hatch/variants/baseboard: Update PL2 power limit value | Sumeet Pawnikar |
2019-06-21 | mb/google/hatch/variants/kindred: Update memory strap GPIOs | David Wu |
2019-06-21 | mb/google/hatch: Do not pull down GPP_F2 internally | Philip Chen |
2019-06-20 | mb/google/hatch: Remove unused USB2 port5 from baseboard devicetree | Aamir Bohra |
2019-06-19 | mb/google/hatch/variants/hatch: Adjust all I2C CLK to meet spec | John Su |
2019-06-16 | mb/google/hatch: Move memory strap GPIOs under variant gpio header | Aamir Bohra |
2019-06-15 | mainboard/google/hatch: Scrub Helios GPIOs | Tim Wawrzynczak |
2019-06-14 | hatch: Fix pen eject wake polarity | Tim Wawrzynczak |
2019-06-14 | mainboard/google/hatch: Update Helios device tree | Tim Wawrzynczak |
2019-06-13 | mb/google/hatch/variants/helios: Use LPDDR3 memory | Paul Fagerburg |
2019-06-13 | mb/google/{hatch, sarien, arcada}: Make HECI1 chip config disable | Subrata Banik |
2019-06-12 | mb/google/hatch: Disable dynamic clock gating for cr50's GPIO | Subrata Banik |
2019-06-04 | mb/google/hatch: Enable LTR for PCIe ports | Furquan Shaikh |
2019-05-31 | mb/google/hatch: Create helios variant | Tim Wawrzynczak |
2019-05-31 | mb/google/hatch: Create kindred variant | Paul Fagerburg |
2019-05-23 | mb/google/hatch/variants: Fix DPTF sensor IDs | Evan Green |
2019-05-21 | mb/google/kohaku: Set ACPI_GPIO_IRQ_EDGE_BOTH for headset INT | Kane Chen |
2019-05-20 | mb/google/{arcada, hatch, sarien}: Override FSP default GPIO PM configuration | Subrata Banik |
2019-05-20 | mb/google/hatch: Change SD_CD# reset config to PLTRST | Krishna Prasad Bhat |
2019-05-15 | soc/intel/cannonlake: Support different SPD read type for each slot | Philip Chen |
2019-05-10 | mb/google/hatch: Fine tune Goodix touch screen timing | Dtrain Hsu |
2019-05-06 | mainboard/google/hatch: Enable PEN_EJECT_L as wake & notify source. | Tim Wawrzynczak |
2019-04-30 | mb/google/hatch: Modify IRQ configuration to enable RT5682 headset INT | Naveen Manohar |
2019-04-29 | mb/google/hatch/variants/baseboard: remove unused dqs_map | Paul Fagerburg |
2019-04-29 | mb/google/hatch/variants/kohaku: Add support for LPDDR3 configurations | Paul Fagerburg |
2019-04-25 | mb/google/hatch/: FPMCU not rebooted when DUT reboots | Tim Wawrzynczak |
2019-04-25 | mb/google/hatch: Pull up GPP_C13 for hatch and hatch_whl | Philip Chen |
2019-04-24 | mb/google/kohaku: Update overridetree.cb | Tim Wawrzynczak |
2019-04-24 | mb/google/hatch: Move SD card detect GPIO. | Tim Wawrzynczak |
2019-04-24 | mb/google/hatch/var/kohaku: Skip UART0 config in FSP | Furquan Shaikh |
2019-04-19 | kohaku: mb/hatch/gpio: Scrub Kohaku GPIOs. | Tim Wawrzynczak |
2019-04-15 | mb/google/hatch: Update sleep signal assertion widths | Rizwan Qureshi |
2019-04-13 | mb/google/hatch: Restore Goodix Touch Screen | Eric Lai |
2019-04-12 | mb/google/hatch: Use GPIO IRQ for sx9310 device | Furquan Shaikh |
2019-04-12 | mb/google/hatch: Configure reset config to PLTRST for IOAPIC pads | Furquan Shaikh |
2019-04-12 | mb/google/hatch: Skip UART0 config in FSP | Furquan Shaikh |