| Age | Commit message (Collapse) | Author |
|---|
|
Override GPIO pad configurations based on the latest bugzzy schematics.
BUG=b:192521391
BRANCH=None
TEST=Built test coreboot image and boot on bugzzy board
Change-Id: I7c3580e7eb34efed0441ead243343d2d7875d50f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add the support RAM parts for Driblee.
Here is the ram part number list:
1. Hynix H9HCNNNBKMMLXR-NEE
2. Micron MT53E512M32D2NP-046 WT:F
3. Samsung K4U6E3S4AA-MGCR
4. Micron MT53E512M32D1NP-046 WT:B
BUG=b:195619346
BRANCH=keeby
TEST=emerge-keeby coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I683acb91ec13cbd772e732d7f81152ceb3cefc1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56924
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the `_HID` value of device in SSDT depending on the fw_config.
According to value of AUDIO_CODEC_SOURCE field in fw_config(SSFC) which
stored in CBI:
AUDIO_CODEC_ALC5682: _HID = "10EC5682" /* ALC5682I-VD */
AUDIO_CODEC_ALC5682I_VS: _HID = "RTL5682" /* ALC5682I-VS */
BUG=b:193623380
BRANCH=dedede
TEST=ALC5682I-VD or VS audio codec can work normally
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Ic8840454e4934162ea59c742634a56f70b153238
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Add SPD support to lantis for MT53E512M32D1NP-046 WT:B
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=FW_NAME=lantis emerge-dedede coreboot chromeos-bootimage
Change-Id: I22c50a55dd3b8bbda64ba1b607c8b22cc6592f98
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
irq(ACPI_IRQ_LEVEL_LOW) -> ACPI_DESCRIPTOR_INTERRUPT -> IO-APIC,
will assert interrupt frequently;
irq_gpio(ACPI_GPIO_IRQ_EDGE_BOTH) -> ACPI_DESCRIPTOR_GPIO -> INT34C8;
will not assert interrupt frequently;
Because IRQ configuration can't be setted to both EDGE trigger.
BUG=b:195635555
BRANCH=dedede
TEST=Cirrus audio codec PLT pass
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I65bca519f75af84848284f039b6ad67cb1887823
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56973
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the driblee variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:191732473
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DRIBLEE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1ad9a4e0cf7999337b55d62d5cc94e4f6c2e98f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the corori variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:194356176
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CORORI
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I8380d5aab61c99d545625789ff1251ec1caa84a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56796
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add charger current throttling support for galtic
control charger index * 64 = Value mA
32*64=2048
28*64=1792
24*64=1536
20*64=1280
BUG=b:187231627
TEST=Built and tested on boten system
Cq-Depend: chrome-internal:3846209
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5e1849551ff051bca591f19f9e40da4c89ab74e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Haboki is project which use discrete TPM, so add discrete TPM and
disable cr50 in overrideree.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I08f2a562c3f62c60402350151ea260b70890a744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Compatible headphone codec "Realtek ALC5682I-VD" and "cirrus CS42L42"
Compatible AMP codec "ALC1015Q-VB" and "MAX98360"
BUG=b:193373320
BRANCH=dedede
TEST=Both realtek and cirrus audio codec can work normally
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I9121e75eaf46b43e6dc5ef2e31029a153c7a807d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
The TSR1._PSV has been redefined.
It will report errors when disassembling the ACPI tables with the iasl.
It is OK when Removing the TSR1._PSV and adding the TSR0._PSV
BUG=b:194509417
BRANCH=dedede
TEST=The iasl can run on Dut successfully
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I524255c79d3c71573d122944da5058389f79d95d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I726d70b4ffc35a28a654abbd20c866f1410e1aee
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add camera support in devicetree and associated GPIO configuration.
BUG=b:193397569
BRANCH=dedede
TEST=Camera function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I3275ab408f6a03735a35eaa8025c36df09c9898c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the bugzzy variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192521391
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_BUGZZY
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I851b9a75c387586d2fb84b762788e962f33472b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The all shipped magolor and maglia has SSFC= 0x840.
The value is defined as 5M MIPI camera.But the value:0x840 will
conflict with the updated touchscreen field.
It will cause some touchscreen no function if make auto-update new
firmware.The CL would correct the field error.
The original fields:
CAMERA_WFC 38 40
TS_SOURCE 41 44
Correct fields:
MIPI Cam
CAMERA_WFC 38 40
CAMERA_UFC 41 42
CAMERA_VCM 43 44
Touch-screen
TS_SOURCE 45 48
The SSFC value of Magolor:
CAMERA_OVTI5675 5M AF (SSFC = 0x840)
CAMERA_OVTI8856 8M AF (SSFC = 0x880)
BUG=b:194639170
TEST=Build firmware and verify on camera and touch-screen devices
Change-Id: I13d76ce8b932f483e20ca5388f1c67eb39ba12a1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56685
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit f29437862269de24f85392d49f6afa6fa60ac43e.
Reason for revert: It makes cret can't boot to os without depthcharge change. The depthcharge change related with fw_config and will effect other variants.
BUG=b:194961854
TEST=Build and boot to OS.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I929369c9419375e74be61a4ff3e5566b0f41ce65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The cappy2 removed the anpec apw8738bqbi and "disable_external_bypass_vr" should be set to "1" to disable
BUG=b:194146867
BRANCH=dedede
TEST=VCCIN_AUX is disable
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ieb4182a989459db629e3b69757c293ca26e8b0cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Using Tpm2.0 device instead of the Cr50 in cappy2
BUG=b:191743435
BRANCH=dedede
TEST=tpm2.0 device function is ok
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I216ceb6386ad57c9f1982187a4525d89869fa9c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56658
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:187801363
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I9328e758ed92389e44b25ff4daf6ec19b37ae7d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.corp-partner.google.com>
|
|
Add tp and audio devices support in devicetree.
BUG=b:193099842
BRANCH=dedede
TEST=i2c devices function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I995e93b5a4c4294d6f6b97c48d14fabf48004d92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56513
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:193898133
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ic84dc83b749cf3c6029a06730096b64ef8cb8cd9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Audio codec:388.91 kHz
Touchpad:394.48 kHz
BUG=b:193864546
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Change-Id: Ia57c90ead44ceb0990878dc0566e595bae5a9099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56383
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add wifi sar for magister.
Due to fw-config cannot distinguish between magolor and magister.
Using sku_id to decide to load magister custom wifi sar.
BUG=b:192290227
TEST=build and test on magolor/magister
Cq-Depend: chrome-internal:3986580
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4510cc2ad42a11ec802ecd439b353f8e87d63868
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
to 0ms
LTE module L850-GL may encounter U3 wakeup race condition with the host.
Setting xHCI LFPS periodic sampling off time to 0ms so that the host would not
miss the device-initiated U3 wakeup thus avoid the race condition.
BUG=b:191426542
BRANCH=dedede
TEST=flash the image to the device. Run following command to check the bits[7:4] is 0x0:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I3be7adad49f87956a6764ad91fec6e76681b393f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chiasheng Lee <chiasheng.lee@intel.com>
|
|
This change adds fine-tuned USB2 PHY parameters for pirika.
BUG=192601233
TEST=Built and verified USB2 eye diagram test result
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Change-Id: Icf9fb41cd0ae40728e4ec5bd72a15ec3c45c963b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add supported memory 'K4U6E3S4AA-MGCR' for cappy2
BUG=None
TEST=Build the cappy2 board.
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ie76a4dca607bb2c3261bbe5478209a43e8430591
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Provide an option to set xHCI LFPS period sampling off time
(SS_U3_LFPS_PRDC_SAMPLING_OFFTIME_CTRL in JSL EDS revision 2.0).
If the option is set in the devicetree, the bits[7:4] in
xHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated.
The host will sample LFPS for U3 wake-up detection when suspended, but
it doesn't sample LFPS at all time due to power management, the
default xHCI LFPS period sampling off time is 9ms. If the xHCI LFPS
period sampling off time is not 0ms, the host may miss the
device-initiated U3 wake-up and causes some kind of race condition for
U3 wake-up between the host and the device.
BUG=b:187801363, b:191426542
TEST=build coreboot with xhci_lfps_sampling_offtime_ms and flash
the image to the device. Run following command to check the bits[7:4]:
iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Ben Kao <ben.kao@intel.com>
Change-Id: I0e13b7f51771dc185a105c5a84a8e377ee4d7d73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wifi sar for cret.
BUG=b:194163601
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ic2f3dbc5822c1f4b1c935c87295ba9916e0e359e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Due to new sku id apply for AMP ALC1015Q-VB. Modify correct WIFI-SAR
detect condition for boten/botenflex sku.
BUG=b:186174768
TEST=build and test on boten/botenflex
Change-Id: I0a4fb08e558fee26534564aa5e37cac814c5a98a
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875582
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I6d87bc63a66ff38bc2f706d58b8537c052bf4594
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure I2C high / low time in the device tree to ensure I2C
CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
touchpad:390.4 kHz
BUG=b:192601250
BRANCH=dedede
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ibe1603a48a3e841b6a50aa0c703697ec615b2854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The caller is already passing the address to the required LTE reset and
enable GPIO. During memcpy, the address to that pointer is used which
will lead to copying undefined data. Fix the pointer/address used in
memcpy.
BUG=None
BRANCH=dedede
TEST=Build Kracko, Drawcia and Metaknight mainboards which use this
function.
Change-Id: I79d6d9af03acd59ab5e1cd7df97bf451011dfeaa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Found-by: Coverity CID 1458053, 1458054.
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56046
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Cret doesn't support SDCard. Disable SDCard contorller for Cret.
BUG=b:191232222
TEST=Build and boot to check lspci
Cq-Depend: chromium:2993724
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I889f0545883aa75813dd91dc3e6a4dcfc246687f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add G2 touchscreen support for magma.
BUG=b:189852808
TEST=Build and verify that touchscreen works.
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I3e032bff7f3e97f54f3e544035e862058ea0dbfc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Create the cappy2 variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:192035460
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY2
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I772801152b9ca9c2c6afe76a353cb2b62d6210ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE modem to devicetree.
Configure GPIO control for LTE modem by fw_config.
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:186393848
TEST=Build image and check with command modem status
Change-Id: I20450ae37e5047dba67211316515994bd2a09600
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update LTE USB port configuration at run-time after probing FW_CONFIG.
By default the concerned USB port takes the Type-A port configuration.
BUG=b:178092096
BRANCH=dedede
TEST=Build and boot to OS to check LTE by modem status
Change-Id: If12cc29ddda6d5c32c0bda840a3680e7bf932f89
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54671
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds fine-tuned USB2 PHY parameters for storo.
BUG=191089827
TEST=Built and verified USB2 eye diagram test result
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I38dd8ad59b32f635e641765e0a1bd13651180d23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
To reduce power load, set unused GPIOs to NC and close
unused interface in devicetree. GPIOs and
interfaces are as below:
GPIO: GPP_C18/C19/D12/D14/D15/D19/D20/D21/E00/E02/H06/H07
Interface: I2C1/I2C3/I2C5
USB: port2_3/2_4/2_6
BUG=b:185044041
BRANCH=dedede
TEST=Built bios and test, it reduces power load without affecting
device function.
Change-Id: Ib5999f0e129bf3e660fe293eda7af3e8e1426151
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ben Kao <ben.kao@intel.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I4dbe3947779395903d7999627948d3e97d6cc985
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add cs42l42 codec support in cret.
BUG=b:188623237, b:189073353
TEST=Build and boot to check functional with cs42l42 EV board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2c53291e07fd785c1360c05171eed634788bc665
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55091
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:190518303
BRANCH=None
TEST=emerge-dedede coreboot
Change-Id: I4005047e0c5f39a12c161a92fbd0afaaec1dc976
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
|
|
Support audio AMP selection with fw_config.
BUG=b:188446060
BRANCH=None.
TEST=built pass
Change-Id: Idf0eb2a87bfa9665e61d185e37adb90987f3cefb
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
|
|
Modify driver from hid to generic(ELAN0001 that used
generic driver without hid).
BUG=b:191620724
BRANCH=dedede
TEST=build bios and boot, touchscreen will work properly.
Change-Id: Ife77d514d9906049f237edd169bc07bb53c48579
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
|
|
Add weida touchscreen support for magister.
BUG=b:191633024
BRANCH=dedede
TEST=Build and verify that touchscreen works on magister.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I3de6a84d2d58ef87f0ae13e8a117a980a0210ac4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Randy Lai <randy.lai@weida.corp-partner.google.com>
|
|
Use drivers/i2c/hid can't update firmware by kernel update script,
so change to drivers/i2c/generic.
BUG=b:188602529
BRANCH=dedede
TEST=can update ELAN touchpad firmware(277.0_1.0) by kernel script
Change-Id: I3592403fe5d0f8d0f67059f8296277e3c028c117
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55248
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875582
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ica2f2856000c8dcbf4d23b7b4a3c479dc7d4862b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enable Acoustic noise mitigation for blipper and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:187760191
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I187702c23712416eaaaaf1e210dcfc6b2c560041
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
On dedede boards without Cr50, the CrOS Board Info (CBI) EEPROM write
protect signal is decoupled from the hardware write protect signal.
Instead, we'd like for it to mirror the software write protect status.
This commit simply checks the software write protect status of the SPI
flash and sets the CBI EEPROM write protect if it's enabled. To prevent
changing the WP signal at run-time, the GPIO configuration is also
locked down after the level has been set. If HW WP is deasserted, the
CBI EEPROM WP will be deasserted as well.
BUG=b:191189275,b:184592299
BRANCH=None
TEST=Build and flash lalala, disable SW WP by running `flashrom -p host
--wp-disable` from a root shell and verify that the GPIO is asserted
after a reboot. Export the gpio via sysfs and verify that attempting to
change the value of the GPIO is futile. Enable SW WP via `flashrom -p
host --wp-enable` and reboot the DUT. Again, export the GPIO via sysfs
and verify that attempts to change the GPIO value are futile.
localhost ~ # iotools mem_read32 0xfd6e08d0
0x44000200
localhost ~ # cd /sys/class/gpio/
localhost /sys/class/gpio # echo 217 > export
localhost /sys/class/gpio # cd gpio217/
localhost /sys/class/gpio/gpio217 # echo out > direction
localhost /sys/class/gpio/gpio217 # cat value
0
localhost /sys/class/gpio/gpio217 # echo 1 > value
localhost /sys/class/gpio/gpio217 # cat value
1
localhost /sys/class/gpio/gpio217 # iotools mem_read32 0xfd6e08d0
0x44000200
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: Ic103037921ec7d2f96f86178675c11a3a1357d1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Touchpad: 387.7kHz
Touchscreen: 389.4kHz
Audio: 387.6kHz
P-sensor: 372.5kHz
BaUG=b:178092096
BRANCH=dedede
TEST=Build and EE check after tuning I2C clock is under 400kHz
Change-Id: I4f6bdd3802cd94671325a89458cde981a2ffa929
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the cappy variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190515828
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CAPPY
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Id5a3b0cb475ee77a9f62523d8322a5e4123ce3be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add camera support in devicetree.
BUG=b:190797339
BRANCH=None.
TEST=built pirika firmware and verified camera function is OK.
Change-Id: I66ded32105f3166e2faec3ea5dcfb93c29822366
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55450
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
speaker L/R
Add Realtek audio codec ALC5682I and speaker L/R the same way as in waddledee
BUG=b:188446060
BRANCH=dedede
TEST=Boot to check ALC5682I and speaker L/R are functional
Change-Id: I8173ffbfb1a8f18978a5e35c69972d4a6d8cb04a
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54529
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add low_power_probe config to camera devices so that driver skips initial
probe during kernel boot and hence prevents privacy LED blink.
BUG=b:178060668
TEST=Build and boot to OS on Drawcia. Ensure no blink on privacy LED.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I00dfe2ce0b57ff3eaa258204f49e79a280754dcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52190
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:181189479
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I379c0ea79a7c27bdd81ed41a54135f7284fb6412
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure GPIO D22/D23/E11.
Add P-sensor to device tree, these registers are draft version.
BUG=b:178092096
BRANCH=dedede
TEST=built firmware and dmesg shows STH9324 initial success.
Change-Id: I2c8feedd6efc1a471304322a17480c836e22349e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Id18a38cddbcacbafbe2c54d94dbda5e00de02b3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Add Goodix GT7996F touchscreen into devicetree for cret.
BUG=b:180547935, b:188501391
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2a6f7c1e9900492937202c0bc6595674f1e79e5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Elan eKTH7D18 touchscreen into devicetree for cret.
BUG=b:180547935, b:187484857
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iab87ddfc7b46420439efa3e7e55c88ad4c27155d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately (380<frequency<400 kHz).
Measured touchpad I2C frequency is 394 kHz
BUG=b:189740533
BRANCH=dedede
TEST=Build bios and make sure frequency meets specification.
Change-Id: Ibc0504a5be6fe9237b8b30783c659a761d10561a
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
haboki/habokay is the same design as drawlat/drawcia, and differs only
in replacing Cr50 with discrete TPM.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot
Cq-Depend: chrome-internal:3850094
Change-Id: Id866927b7041c5bf1c73fb4f0c03798eb61efa79
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54755
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory MT53E512M32D1NP-046 WT:B in the mem_parts_used.txt and
generate the SPD ID for the parts.
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib797af858e8f7ea275291e552102db74f4724aad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchpad into devicetree for sasukette.
BUG=b:188376649
BRANCH=dedede
TEST=built sasukette firmware and verified touchpad function
Signed-off-by: lizhi7 <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I898aeda936eb10ef4ead679a1c087060fad71a08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drawper would use synaptics touchpad.
BUG=b:184878424
TEST=emerge-dedede coreboot and check touchpad function work.
Change-Id: I2d2c205e19d8e3472e0fa7ca20fd38e381ac0de0
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Drawper support LTE+HDMI,
so use DB_PORTS_1A_HDMI_LTE to select HDMI VBT output for it.
BUG=b:186393848
BRANCH=dedede
TEST=Build and boot to OS check HDMI output works.
Change-Id: Ibf34cce1e3cbfce8a71dce880c50f85db9295b1e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DB_PORTS_1C_1A_LTE 6
DB_PORTS_1C 7
DB_PORTS_1A_HDMI_LTE 8
BUG=b:186393848
BRANCH=dedede
TEST=build pass
Change-Id: I8632960d7e538402bf033d07402116dac848f5ac
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Move discrete TPM in the devicetree to avoid emitting the following
message: "Using default TPM ACPI path: '\_SB_.PCI0.LPCB'"
There is no corresonding ACPI device for 1f.5 PCI device. Therefore,
move the discrete TPM to a device that has the corresponding ACPI
device node. Functionality should remain the same.
BUG=b:187518267
Change-Id: Ie9ec70336d5651c87f06f8b357abd1bfdb1cc06b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
|
|
Add ELAN Touchpad device under I2C0
BUG=b:188373661
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Change-Id: I15b9cb0d0276b5e2dd06694530cc35e5643efb9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52936
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable/disable LTE function based on LTE bit of FW_CONFIG.
The LTE function settings are included GPIO settings, USB port settings and
power off sequence.
BUG=b:187797408
BRANCH=dedede
TEST=Build and test the change on cret.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib926e99aaf9df433a7cff71180ee55431d69f718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DPTF parameters from thermal team.
1. Modify TSR1 sensor as charge sensor.
2. Modify P-state parameter
BUG=b:180641150
BRANCH=dedede
TEST=build and verified by thermal team.
Change-Id: I43002db61de650d29cd85944a4eaea1b2f99aec4
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52755
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select touchscreen(s) based on touchscreen source provisioned in SSFC of CBI (higher 32 bits of FW_CONFIG in coreboot).
The reason is to avoid to enable multiple touchscreen ICs with the same slave address.
BUG=b:186609348
TEST=build and boot to OS.
Change-Id: I087ea677a8865fc8c5b3f7c9773bd7f97924dbb3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Remove TSR2 and use DPTF parameters from internal thermal team.
BUG=b:175938681
TEST=build and boot to OS.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If0ec1ec48b8971efe87f1f8d10332a9c16352122
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Probe the fw_config for RT1015 speaker amplifier operation mode and
enable it accordingly in the device tree.
BUG=b:180570923
BRANCH=dedede
TEST=ALC1015Q-VB drive speaker OK
Change-Id: I756bfa6f604ed320de9a515821979aa95c869ebf
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add support for GPIO and SPD driver for pirika
BUG=b:184157747
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: Id367a83b04aad62b7deabae99b3f91905a2fc46c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update LTE USB port configuration at run-time after probing the firmware
config. By default the concerned USB port takes the Type-A port
configuration.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight
Change-Id: I5ad5a1670adef54075923cf912fb41a1ce776155
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
This callback is required to update the devicetree config at run-time
after probing the firmware config.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight.
Change-Id: I857211bfc4beb36ab225f3786c1707336a34aae9
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
Create the pirika variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:184157747
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_PIRIKA
Signed-off-by: kirk_wang <kirk_wang@pegatron.corp-partner.google.com>
Change-Id: I57bf33deeadacc88800f9ce1d3d54385ba56c798
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52626
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify reset pin setting to ACPI_GPIO_OUTPUT_ACTIVE_LOW for
ELAN and Weida touchscreen.
BUG=b:180547621
BRANCH=dedede
TEST=Build the cret board and touchscreen is workable.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I912fe8a0e18a4c3527fb8587592b855c93b12406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Default VBT supports only integrated Display port. Magister supports a
HDMI port and hence support a separate VBT for Magister.
BUG=b:180666608
BRANCH=dedede
TEST=Build and boot to OS.
Cq-Depend: chrome-internal:3661227
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I52c10452887312959f68cfc4e25d5897dae388f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51279
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because galith/gallop both non-suport tablet mode,
remove un-use fw_config conditional.
BUG=b:176206495
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ic9bb76c207ef033f81ecdd57849535b8ac8d13ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52565
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define TOUCH_RPT_EN pin(GPP_A11) as the stop_gpio for the touch screen
and control TOUCH_RPT_EN pin to keep low.
BUG=b:176253069
TEST=Build and boot metaknight to OS, confirm GPP_A11 pin keep low.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I816e29eccac0f1935aeaa3b94c907870e2451e3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52653
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, it fails to dump the nvme data by test command.
It reports the following error:
cat: '/sys/bus/i2c/devices/i2c-PRP0001:01/eeprom': Connection timed out
So increase the value from 0x0400 to 0x2000 and double the address width from 0x08 to 0x10 to solve this problem.
BUG=b:177393430
TEST=1. cat /sys/bus/i2c/devices/i2c-PRP0001:01/eeprom > /tmp/ov8856_eeprom.bin
2. hexdump -C /tmp/ov8856_eeprom.bin > ov8856_eeprom_dump.log
3. cat ov8856_eeprom_dump.log
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ia933927981f07e0f7954a4bc6d82f0bdd70181f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52048
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: ShawnX Tu <shawnx.tu@intel.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch has changes to support multiple cameras modules, based on
the value set in the SSFC_CONFIG.
BUG=b:176065425
TEST=Tested the changes with magolor 5MP and 8MP camera.
Change-Id: I764abf70bacbe61452e7b0fd59c1b375227b5748
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add control charging current from TSR0 and correct charger_perf table value.
BUG=b:179067801
BRANCH=dedede
TEST=emerge-dedede coreboot
Change-Id: Ie0d969898defe76952e5c136fa93b7edffe51de3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Edward Doan <edoan@google.com>
|
|
Metaknight has two daughter-board (DB_PORTS_1A_HDMI and
DB_PORTS_LTE_HDMI), LTE and USB Type A use the same usb port,so needs to
probe daughter-board to avoid USB device cannot recognize correctly.
BUG=b:184809456
TEST=build and verify USB device can recognize correctly
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie42d12c7ce5c7341751c3cf92b5f37b6cd4d479f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raymond Wong <wongraymond@google.com>
Reviewed-by: Kaiyen Chang <kaiyen.chang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
support audio AMP selection with fw_config.
BUG=b:185082705
BRANCH=dedede
TEST=build pass
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ieb169c69a6716082dd218d05479bca46bbc09a3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add AUDIO_AMP ports bit field in devicetree.
UNPROVISIONED 0
MAX98360 1
RT1015_I2C 2
RT1015P_AUTO 3
BUG=b:185082705
BRANCH=dedede
TEST=build pass
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I54f1e44036857dc00df074c38fde0fa82e589320
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52317
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify GPIO_D22/D23/E11 configuration for P-sensor
BUG=b:185214363
BRANCH=dedede
TEST=built storo firmware and verified P-sensor function
Change-Id: Ia2df1a227b04688a6b98384cd3a4e63023c0c1d9
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE modem to devicetree
Configure GPIO control for LTE modem
BUG=b:178092096
TEST=Built image and verified with command modem status
Change-Id: Id8f483e1132a08500fbe950711cc84197ce40b12
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wifi sar for botenflex.
Due to fw-config cannot distinguish between boten and botenflex.
Using sku_id to decide to load botenflex custom wifi sar.
Detail reason for using sku_id in b:182433707.
BUG=b:182433707
TEST=build and test on boten/botenflex
Cq-Depend: chrome-internal:3686313
Change-Id: Id3f2529a7ad56ff306df98f77cda556656da52a5
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree and gpio setting of metaknight to handle pen detection.
BUG=b:180426949
TEST=Build and check behavior is expected.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ieeca20eff57b16217a13d996dca3f662911f3e5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add LTE module support into devicetree and associated GPIO configuration.
BUG=b:183774169
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I14684bb30e46bf845a401649f56b16b60db379e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
