| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I7ecc394b1e5bc0b8b85a8afac22efc0befe2d36a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3395
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This reverts commit 0210119b4b95e84f954cfd6dc11aafbc187421af
Change-Id: I5be3f2a54394c592650a0dcd671e4a72ae796cb2
Reviewed-on: http://review.coreboot.org/3443
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If56f2cacc5f1b2ef9c7b6aea508d458a43dd1309
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3397
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a struct for referencing UART registers. The layout is quite
strange on this chip, as the entire register space can take on three
different meanings depending on the line control settings (in the LCR
register) And to make things more confusing, some offsets reference
different registers depending on if a read or a write operation is
used.
Change-Id: Ie62af9c0e0edafd01b81686a0fe5c5c1d4fa06c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The current method will treat hex values as 0 and would calculate the wrong
size. This change switches back to an earlier method which used shell syntax
to add the offset and size.
Change-Id: I9fb2d9b323f113cc56a5ad2e38b47d2d22084f08
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3432
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The bootblock and ROM stages are the only ones that are really required to be
loaded in the quite limited on chip RAM during startup. Rather than load the
whole image which requires everything to be small, load just the bootblock and
the ROM stage, allowing the rest of the image to be arbitrarily large. Loading
a minimal amount of stuff should also improve boot performance a little bit.
Change-Id: I2fede63b8d3d8f0d880e4a692ae423021f8232b6
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3421
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Loading on an OMAP SOC requires that the first sector of the image have a
configuration header, and, when not an execute in place image, an additional
header which describes how big the image is and where it should be loaded.
This change adds some infrastructure to statically build that header using C
code, and to paste the header onto the front of coreboot.rom in a new top
level target file called MLO.
The configuration header we're using is as inert as possible, in line with
what U-Boot is doing. I think it could be used to give additional
configuration parameters to the built-in ROM on the SOC, but we don't need to
do that, and there didn't seem to be any actual documentation how to do that.
Because the header is built from C and is defined per CPU, it would be
possible to include extra settings in other CPUs if desired.
Adding a new top level build target is a bit disruptive, but should be
contained to the am335x directory and not interfere with other mainboards.
Change-Id: I06d346a4050c20963b3c7c6e8a152070bf2d145a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3332
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
fam15 vendorcode (src/vendorcode/amd/agesa/f15tn) was licensed under the
AMD software license agreement. Change this license to 3-clause BSD.
Change-Id: I7cab09bb58ef7cd24602628e2278672d577214a2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3414
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch adds a qemu x86 cpu chip. It has no initialization function
as this isn't needed on virtual hardware. A virtual machine can have
pretty much any CPU: qemu emulates a wide range of x86 CPUs (try 'qemu
-cpu ? for a list), also with 'qemu -cpu host' the guest will see a cpu
which is (almost) identical to the one on the host machine. So I've
added X86_VENDOR_ANY as wildcard match for the cpu_table.
Change-Id: Ib01210694b09702e41ed806f31d0033e840a863f
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3344
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
While we had support for updating microcode on the VIA Nano CPUs for a
while now, we never included the actual microcode. Unlike, Intel and
AMD CPUs, VIA microcode is not available for download, and was
extracted from the vendor BIOS. It was not included in coreboot since
we never had explicit permission to do so. I have just received
confirmation from VIA that we can distribute the microcode.
Change-Id: I4c15b090cd2713cfe5dc6b50db777ff89dbc0f19
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3357
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
There were assumptions being made in the haswell
MP and SMM code which assumed the APIC id space
was 1:1 w.r.t. cpu number. When hyperthreading is
disabled the APIC ids of the logical processors
are all even. That means the APIC id space is sparse.
Handle this situation.
Change-Id: Ibe79ab156c0a171208a77db8a252aa5b73205d6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3353
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some settings in the am335x Kconfig weren't actually used for anything, some
where place holders, and some where left over from another CPU. The memory
addresses are in the internal RAM in the SOC as described in the reference
manual. The stack is put where the internal ROM had its stack, and the
bootblock is put at the bottom of that region as the manual suggests. The
ROM stage offset is set to 10K which is a bit bigger than the ~7.5K the
bootblock currently takes up.
Change-Id: I1a117d789a791d7e3db1118823f8216b3361433c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3327
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The following is an excerpt from serial log of the Bachmann OT200.
$ grep usec coreboot_log
clocks_per_usec: 500
Root Device init 48034 usecs
CPU_CLUSTER: 0 init 133251 usecs
PCI: 00:01.0 init 33376 usecs
PCI: 00:01.1 init 9930 usecs
PCI: 00:01.2 init 9929 usecs
PCI: 00:04.0 init 9929 usecs
PCI: 00:0f.0 init 185788 usecs
PCI: 00:0f.2 init 21473 usecs
PCI: 00:0f.3 init 9930 usecs
PCI: 00:0f.4 init 9930 usecs
PCI: 00:0f.5 init 9930 usecs
PCI: 00:0f.6 init 9930 usecs
PCI: 00:0f.7 init 9929 usecs
Change-Id: I4d0805c4cf8fcb25ec107615787fc6da0c945a30
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3308
Tested-by: build bot (Jenkins)
|
|
Initial structure of Beaglebone port
Change-Id: Ia255ab207f424dcd525990cdc0d74953e012c087
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Thanks to Aaron Durbin coreboot provides monotonic timers. Select
the LAPIC monotonic timer for the AMD AGESA CPUs.
The following is an excerpt from serial log of the ASRock E350M1.
$ grep usec seriallog-20130502_100902.log
01.016: Root Device init 1578 usecs
01.029: CPU_CLUSTER: 0 init 112415 usecs
01.029: PCI: 00:00.0 init 3240 usecs
01.088: PCI: 00:01.0 init 104572 usecs
01.088: PCI: 00:01.1 init 1663 usecs
01.088: PCI: 00:11.0 init 1662 usecs
01.088: PCI: 00:14.0 init 1662 usecs
01.088: PCI: 00:14.3 init 8665 usecs
01.088: PCI: 00:14.4 init 1665 usecs
01.088: PCI: 00:18.0 init 1662 usecs
01.088: PCI: 00:18.1 init 1663 usecs
01.088: PCI: 00:18.2 init 1663 usecs
01.088: PCI: 00:18.3 init 1663 usecs
01.088: PCI: 00:18.4 init 1663 usecs
01.088: PCI: 00:18.5 init 1665 usecs
01.088: PCI: 00:18.6 init 1664 usecs
01.088: PCI: 00:18.7 init 1663 usecs
01.088: PNP: 002e.2 init 1576 usecs
01.088: PNP: 002e.5 init 1577 usecs
01.088: PNP: 002e.a init 1590 usecs
01.088: PNP: 002e.b init 30144 usecs
01.088: PCI: 03:00.0 init 1663 usecs
So the graphics device needs around 100 ms for being initialized.
The full serial log is in the Gerrit comments.
Change-Id: Ia7b3012e51fcf94b0f22290cdef2b4424295ad6d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3172
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Commit »haswell: 24MHz monotonic time implementation« (c46cc6f1) [1]
added the Kconfig variable `MONOTONIC_TIMER_MSR` with a help text,
but only used one space instead of the suggested two spaces for
indentation. So add one space.
»Lines under a "config" definition are indented with one tab, while
help text is indented an additional two spaces.« [2]
[1] http://review.coreboot.org/3153
[2] https://www.kernel.org/doc/Documentation/CodingStyle
(Chapter 10: Kconfig configuration files)
Change-Id: I39cf356bfd54c66a2f1b837c6667dcc915e41f29
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3262
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The haswell code allows for vboot ramstage verification.
However, that code path relies on accessing global cache-as-ram
variables after cache-as-ram is torn down. In order to avoid
that situation enable cache-as-ram migration.
cbmemc_reinit() no longer needs to be called from romstage
because it is invoked automatically by the cache-as-ram
migration infrastructure.
Change-Id: I08998dca579c167699030e1e24ea0af8802c0758
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3236
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There are some boards that do a significant amount of
work after cache-as-ram is torn down but before ramstage
is loaded. For example, using vboot to verify the ramstage
is one such operation. However, there are pieces of code
that are executed that reference global variables that
are linked in the cache-as-ram region. If those variables
are referenced after cache-as-ram is torn down then the
values observed will most likely be incorrect.
Therefore provide a Kconfig option to select cache-as-ram
migration to memory using cbmem. This option is named
CAR_MIGRATION. When enabled, the address of cache-as-ram
variables may be obtained dynamically. Additionally,
when cache-as-ram migration occurs the cache-as-ram
data region for global variables is copied into cbmem.
There are also automatic callbacks for other modules
to perform their own migration, if necessary.
Change-Id: I2e77219647c2bd2b1aa845b262be3b2543f1fcb7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3232
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
build-snow got broken when the snow makefile improved. So fix it.
While we're at it, create a script like the update-microcode
scripts that gets the bl1. I thought about making this a common
script but the various names and paths always evolve, leaving
me thinking it's not worth it. This script is just a
piece of the snow build script.
Change-Id: I65c0f8697a978c62fe12533c4f0152d14dbaefda
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3238
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Thread support is added for the x86 architecture. Both
the local apic and the tsc udelay() functions have a
call to thread_yield_microseconds() so as to provide an
opportunity to run pending threads.
Change-Id: Ie39b9eb565eb189676c06645bdf2a8720fe0636a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3207
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Since this parameter is not used anymore, drop it from
all calls to copy_and_run()
Change-Id: Ifba25aff4b448c1511e26313fe35007335aa7f7a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some entries still used spaces while others used tabulators[1]. Convert
spaces to tabs to uniformly use tabs.
---------------------- 8< -------------- 8< -----------------------------
For all of the Kconfig* configuration files throughout the source tree,
the indentation is somewhat different. Lines under a "config" definition
are indented with one tab, while help text is indented an additional two
spaces. [2]
---------------------- 8< -------------- 8< -----------------------------
[1] http://en.wikipedia.org/wiki/File:HollerithMachine.CHM.jpg
[2] http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/Documentation/CodingStyle?id=HEAD
Change-Id: Iee80ad4a90e95b925afbb0c6adc563fa3a6503cf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3173
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Since the TSC udelay() function can be used in SMM that means the
TSC can count up to whatever value. The current loop was not handling
TSC rollover properly. In most cases this should not matter as the TSC
typically starts ticking at value 0, and it would take a very long time
to roll it over. However, it is my understanding that this behavior is
not guaranteed. Theoretically the TSC could start or be be written to
with a large value that would cause the rollover.
Change-Id: I2f11a5bc4f27d5543e74f8224811fa91e4a55484
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3171
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When the haswell MP/SMM code was developed it was using a coreboot
repository that did not contain the asmlinkage macro. Now that the
asmlinkage macro exists use it.
BUG=None
BRANCH=None
TEST=Built and booted.
Change-Id: I662f1b16d1777263b96a427334fff8f98a407755
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3203
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have the monotonic timer implemented on exynos now, and this
also enables helpful bootstage prints with timing info.
Change-Id: I3baa4c9d70d4b4d059abd5e05eddcabd5258dbfd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3210
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Some boards use the local apic for udelay(), but they also provide
their own implementation of udelay() for SMM. The reason for using
the local apic for udelay() in ramstage is to not have to pay the
penalty of calibrating the TSC frequency. Therefore provide a
TSC_CONSTANT_RATE option to indicate that TSC calibration is not
needed. Instead rely on the presence of a tsc_freq_mhz() function
provided by the cpu/board. Additionally, assume that if
TSC_CONSTANT_RATE is selected the udelay() function in SMM will
be the tsc.
Change-Id: I1629c2fbe3431772b4e80495160584fb6f599e9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3168
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of using the local apic timer for udelay() use the tsc.
That way SMM, romstage, and ramstage all use the same delay
functionality.
Change-Id: I024de5af01eb5de09318e13d0428ee98c132f594
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3169
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This re-introduces 2fde966 (http://review.coreboot.org/#/c/3177/)
which was reverted due to unsatisfied dependencies.
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Change-Id: I8e60105629d9da68ed622e89209b3ef6c8e2445b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This goes thru various call sites where we used timer_us() and updates
them to use the new monotonic timer API.
udelay() changed substantially and now gracefully handles wraparound.
Change-Id: Ie2cc86a4125cf0de12837fd7d337a11aed25715c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3176
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
This reverts commit 2fde9668b47e74d1bfad2f1688a4481e6b966d04
Somehow this got merged before its dependencies. 3190 must be merged first, followed by 3176. However 3190 will fail while this patch is in. So the situation can't correct itself.
Reverting this until the other two go in.
Change-Id: I176f37c12711849c96f1889eacad38c00a8142c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3195
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I14ebf75649d101491252c9aafea12f73ccf446b5
Reviewed-on: http://review.coreboot.org/3177
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit
commit 825c78b5da98c7155ff6be3322cdaae0e5a060e8
Author: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Date: Thu May 2 18:06:03 2013 -0600
mainboard/{asus/f2a85-m,amd/thatcher}: move UDELAY_LAPIC
Reviewed-on: http://review.coreboot.org/3178
adds `UDELAY_LAPIC` to `cpu/amd/agesa/family15tn/Kconfig`. This is
not needed, because since commit
commit e135ac5a7ea69b6edcb89345019212f5de412b1e
Author: Patrick Georgi <patrick.georgi@secunet.com>
Date: Tue Nov 20 11:53:47 2012 +0100
Remove AMD special case for LAPIC based udelay()
Reviewed-on: http://review.coreboot.org/1618
`select UDELAY_LAPIC` is present in `src/cpu/amd/agesa/Kconfig` which
applies also to AMD Family 15tn.
Therefore remove `select UDELAY_LAPIC` again from
`cpu/amd/agesa/family15tn/Kconfig`.
Change-Id: I98b783a97c4a1e45ecb29b776cb3d3877bad9c0f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3179
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This implements the new monotonic timer API using the global
multi-core timer (MCT).
Change-Id: Id56249ff5d3e0f85808f5754954c83c0bc75f1c1
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3175
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
Stefan Reinauer suggested 'select UDELAY_LAPIC' did not belong in
f2a85-m/Kconfig. It got there via copy-paste from thatcher/Kconfig
so this commit removes the 'select UDELAY_LAPIC' from both and puts
it in cpu/amd/agesa/family15tn/Kconfig
Since f2a85-m is the only Thatcher board coreboot supports right
now, this should not break any other boards.
Change-Id: I811b579c31f8d259a237d3a6724ad3b17f3a6c3e
Signed-off-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-on: http://review.coreboot.org/3178
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
Implement the timer_monotonic_get() using the TSC.
Change-Id: I5118da6fb9bccc75d2ce012317612e0ab20a2cac
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3155
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Implement the timer_monotonic_get() functionality based off of
the local apic timer.
Change-Id: I1aa1ff64d15a3056d6abd1372be13da682c5ee2e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3154
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Haswell ULT devices have a 24MHz package-level counter. Use
this counter to provide a timer_monotonic_get() implementation.
Change-Id: Ic79843fcbfbbb6462ee5ebd12b39502307750dbb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On x86 systems there is a concept of cachings the ROM. However,
the typical policy is that the boot cpu is the only one with
it enabled. In order to ensure the MTRRs are the same across cores
the rom cache needs to be disabled prior to OS resume or boot handoff.
Therefore, utilize the boot state callbacks to schedule the disabling
of the ROM cache at the ramstage exit points.
Change-Id: I4da5886d9f1cf4c6af2f09bb909f0d0f0faa4e62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3138
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This makes the intermediate rule visible so BL1 gets automatically
placed in the final image.
Change-Id: Iffb0268e5bbcbe135f2d39863ed64fa302409a22
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3141
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The "wakeup" procedure will be shared by bootblock and romstage for different
types of resume processes.
Note, this commit does not include changes in romstage/bootblock to enable
suspend/resume feature. Simply adding functions to handle suspend/resume.
Verified by successfully building and booting Google/Snow firmware image.
Change-Id: I17a256afb99f2f8b5e0eac3393cdf6959b239341
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3129
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
content.
To support suspend/resume, PHY control must be reset only on normal boot
path. So add a new param "mem_reset" to specify that.
Verified to boot successfully on Google/Snow.
Change-Id: Id49bc6c6239cf71a67ba091092dd3ebf18e83e33
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds support for display bring-up on Snow. It
includes framebuffer initialization and LCD enable functions.
Change-Id: I16e711c97e9d02c916824f621e2313297448732b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3116
Tested-by: build bot (Jenkins)
|
|
Add a safety check in function `intel_update_microcode` to return when
accidentally `NULL` is passed as `microcode_updates`, which would lead
to a null pointer dereference later on.
for (c = microcode_updates; m->hdrver; m = (const struct microcode *)c) {
While at it, use `return NULL` for clarity in function
`intel_microcode_find` and include the header file `stddef.h`. for it.
The review of this patch had some more discussion on adding more
comments and more detailed error messages. But this should be done in
a separate patch.
For clarity here some history, on how this was found and what caused
the discussion and confusion.
Originally when Vladimir made this improvement, selecting
`CPU_MICROCODE_IN_CBFS` in Kconfig but not having the microcode blob
`cpu_microcode_blob.bin` in CBFS resulted in a null pointer dereference
later on causing a crash.
for (c = microcode_updates; m->hdrver; m = (const struct microcode *)c) {
Vladimir fixed this by returning if `microcode_updates` is `NULL`,
that means no file is found and successfully tested this on his
Lenovo X201.
When pushing the patch to Gerrit for review, the code was rewritten
though by Aaron in commit »intel microcode: split up microcode loading
stages« (98ffb426) [1], which also returns when no file is found. So
the other parts of the code were checked and the safety check as
described above is added.
[1] http://review.coreboot.org/2778
Change-Id: I6e18fd37256910bf047061e4633a66cf29ad7b69
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2990
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
This makes sure that the product ID (PRO_ID) register can be read
when the OS kernel is figuring out what kind of CPU it's running on.
For historical reference, the original U-Boot code seems to have
worked basically by accident here. The hardware has a quirk where by
reading the value before gating the IP block keeps the value
persistent. U-Boot reads the chip ID early on to distinguish between
chip family, but we do not mix code the same way so we do not read
the chip ID. Since the value has been read before the clock gating
happens, the value remains available for the kernel to use during the
decompression stage. We don't want to rely on that behavior when using
coreboot. Instead the kernel should gate unused IPs.
(credit to Gabe for finding symptom in the kernel)
Change-Id: Iaa21e6e718b9000b5558f568020f393779fd208e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3121
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
This simple error led to corrupted graphics.
How annoying.
Change-Id: I2295c0df0f1d16014a603dc5d66bd4d72f3fb7c9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3120
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The original imported code used "lcdbase" and "lcd_base" which quite
predictably caused confusion and bugs. Let's put an end to this little
bit of insanity.
Change-Id: I4f995482cfbff5f23bb296a1e6d35beccf5f8a91
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3114
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
descriptor
We neglected to copy xres and yres out; now we do.
Change-Id: Icc4a8eb35799d156b11274f71bcfb4a1d10e01e3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3111
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This updates the Exynos TMU code for coreboot:
- Remove dependency on device tree
- Add Makefile entries
Change-Id: I55e1b624d7c7b695b1253ec55f6ae3de8dc671bc
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3107
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This simply imports the Exynos TMU driver from u-boot. It is not
built and thus should not break anything.
Change-Id: I7861132fbf97f864e4250ffbda1ef3843f296ddc
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3106
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This moves the prototype for power_enable_hw_thermal_trip() to
a generic location so it can be used by generalized thermal
management code. The implementation will still be CPU-specific.
Change-Id: Iae449cb8c72c8441dedaf65b73db9898b4730cef
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3105
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This gets rid of the clock-tick based sdelay in favor of udelay().
udelay() is more consistent and easier to work with, and this allows
us to carry one less variation of timers (and headers and sources...).
Every 1 unit in the sdelay() argument was assumed to cause a delay of
2 clock ticks (@1.7GHz). So the conversion factor is roughly:
sdelay(N) = udelay(((N * 2) / 1.7 * 10^9) * 10^6)
= udelay((N * 2) / (1.7 * 10^3))
The sdelay() periods used were:
sdelay(100) --> udelay(1)
sdelay(0x10000) --> udelay(78) (rounded up to udelay(100))
There was one instance of sdelay(10000), which looked like sort of a
typo since sdelay(0x10000) was used elsewhere. sdelay(10000) should
approximate to about 12us, so we'll stick with that for now and leave
a note.
Change-Id: I5e7407865ceafa701eea1d613bbe50cf4734f33e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3079
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The types are (esp. int) are confusing at times as to size.
Make them definite as to size.
Change-Id: Id7808f1f61649ec0a3403c1afc3c2c3d4302b7fb
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3103
Tested-by: build bot (Jenkins)
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This removes the wait_ms argument from the dp_controller_init(). The
only delay involved is a constant 60ms delay that happens if
everything else goes well. This delay is derived from the LCD spec
so there's no reason it should be baked into the controller code.
(This patch also has the side-effect of fixing a bug where we were
delaying on an undefined value for wait_ms).
Change-Id: I03aa19f2ac2f720524fcb7c795e10cc57f0a226e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3078
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a microsecond timer, its declaration, the function to start it,
and its usage. To start it, one calls timer_start(). From that point
on, one can call timer_us() to find microseconds since the timer was
started.
We show its use in the bootblock. You want it started very early.
Finally, the delay.h change having been (ironically) delayed, we
create time.h and have it hold one declaration, for the timer_us() and
timer_start() prototype.
We feel that these two functions should become the hardware specific
functions, allowing us to finally move udelay() into src/lib where it
belongs.
Change-Id: I19cbc2bb0089a3de88cfb94276266af38b9363c5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3073
Tested-by: build bot (Jenkins)
|
|
Split the Persimmon DSDT into common code areas.
For example, split the Southbridge specific code into
the Southbridge directory and CPU specific code into
the CPU directory. Also adding the superio.asl file
to the Persimmon DSDT tree. This file is empty for
the moment but will be necessary in the future. I have
also emptied the thermal.asl file in the mainboard
directory because it does not seem to perform as
intended (fan control does not change when it is
brought back into the code base) and it has been
inside a '#if 0' statement for a long time. Removing
it until it is decided that it is actually necessary.
This change was verified in three different ways:
1. Visual comparison of the compiled DSDT pulled from the
Persimmon after booting into Linux using the ACPI tools
acpidump, acpixtract, and iasl. The comparison was done
between the DSDT before and after doing the split work.
This test is somewhat difficult considering the expanse
of the changes. Blocks of code have been moved, and
others changed.
2. Linux logs were dumped before and after the DSDT split.
Logs dumped and compared include dmesg and lspci -tv.
Neither log changed significantly between the two compare
points.
3. The test suite FWTS was run on the Coreboot build both
before and after doing the DSDT split with the command
'sudo fwts -b -P -u'. The flag -b specifies all batch jobs,
-P specifies all power tests, and -u specifies utilities.
Interactive jobs were not run as most of them consist of
laptop checks. Again, there were no significant changes
between the two endpoints.
These tests lead me to believe that there was no change in
the functionality of the ACPI tables apart from what is
known and expected.
This patch is the first of a series of patches to split the DSDT.
The ASRock patch was merged before this one and breaks the ASROCK
E350M1 build (patch 8d80a3fb: http://review.coreboot.org/#/c/3050/).
Please be aware of this dependency when pulling these patches.
Other patches that depend on this patch are
'AMD Fam14: Split out the AMD Fam14 DSDT'
(http://review.coreboot.org/#/c/3051/)
and 'Fam14 DSDT: Also return for unrecognized UUID in _OSC'
(http://review.coreboot.org/#/c/3052/)
Change-Id: I53ff59909cceb30a08e8eab3d59b30b97c802726
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Properly use the chip settings when configuring the CPU,
at this point being purely graphics.
Change-Id: I9bc2d32c1037653837937b314e4041abc0024835
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3054
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Add basic edp support to the ramstage. Not working.
Change-Id: I15086e03417edca7426c214e67b51719d8ed9341
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3055
Tested-by: build bot (Jenkins)
|
|
Basic cleanup, this code still does not work.
Change-Id: I84ed9f08fd04cd8eb74cd860e0775d8c602f42d6
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3049
Tested-by: build bot (Jenkins)
|
|
This enables type checking for safety as to help prevent errors like
http://review.coreboot.org/#/c/3038/ . Now compilation fails if the
wrong type is passed into readb/readw/readl/writeb/writew/writel
or other macros in io.h.
This also deprecates readw/writew. The previous definition was 16-bits
which is incorrect since wordsize on ARMv7 is 32-bits and there was
only 1 instance of writew (#if 0'd anyway). Going forward we should
always use read{8,16,32} and write{8,16,32} where N specifies the
exact length rather than relying on ambiguous definition of wordsize.
Since many macros relied on __raw_*, which were basically the same
(minus data memory barrier instructions), this patch also gets rid
of __raw_*. There were parts of the code which ended up using these
macros consecutively, for example:
setbits_le32(®s->ch_cfg, SPI_CH_RST);
clrbits_le32(®s->ch_cfg, SPI_CH_RST);
In such cases the safe versions of readl() and writel() should be
used anyway.
Note: This also fixes two dubious casts as to avoid breaking
compilation.
Change-Id: I8850933f68ea3a9b615d00ebd422f7c242268f1c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3045
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This re-factors the Exynos5 I2C code to be simpler and use the
new API, and updates users accordingly.
- i2c_read() and i2c_write() functions updated to take bus number
as an argument.
- Get rid of the EEPROM_ADDR_OVERFLOW stuff in i2c_read() and
i2c_write(). If a chip needs special handling we should take care
of it elsewhere, not in every low-level i2c driver.
- All the confusing bus config functions eliminated. No more
i2c_set_early_config() or i2c_set_bus() or i2c_get_bus(). All this
is handled automatically when the caller does a transaction and
specifies the desired bus number.
- i2c_probe() eliminated. We're not a command-line utility.
- Let the compiler place static variables automatically. We don't need
any of this fancy manual data placement.
- Remove dead code while we're at it. This stuff was ported early on
and much of it was left commented out in case we needed it. Some
also includes nested macros which caused gcc to complain.
- Clean up #includes (no more common.h, woohoo!), replace debug() with
printk().
Change-Id: I8e1f974ea4c6c7db9f33b77bbc4fb16008ed0d2a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3044
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The existing header was imported along with the Exynos code and left
mostly unchanged. This is the first patch in a series intended to
replace the imported u-boot I2C API with a much simpler and cleaner
interface:
- We only need to expose i2c_read() and i2c_write() in our public API.
Everything else is board/chip-dependent and should remain hidden
away.
- i2c_read and i2c_write functions will take bus number as an arg
and we'll eliminate i2c_get_bus and i2c_set_bus. Those are prone to
error and end up cluttering the code since the user needs to save
the old bus number, set the new one, do the read/write, and restore
the old value (3 added steps to do a simple transaction).
- Stop setting default values for board-specific things like SPD
and RTC bus numbers (as if we always have an SPD or RTC on I2C).
- Death to all the trivial inline wrappers. And in case there was any
doubt, we really don't care about the MPC8xx. Though if we did then
we would not pollute the public API with its idiosyncrasies.
Change-Id: I4410a3c82ed5a6b2e80e3d8c0163464a9ca7c3b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3043
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds a missing address-of operator. This was a subtle bug that
didn't seem to cause problems at first since the serial console
appeared to work. However it caused an imprecise external abort which
became apparent later on when aborts were unmasked in the kernel via
the CPSR_A bit.
(credit goes to Gabe Black for finding this)
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I80a33b147d92d559fa8fefbe7d5642235deb9aea
Reviewed-on: http://review.coreboot.org/3038
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This moves highly board-specific code out from the Exynos5250
power_init() into Snow's romstage.c. There's no reason the CPU-
specific code should care about which PMIC we are using and
which bus it is on.
Change-Id: I52313177395519cddcab11225fc23d5e50c4c4e3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3034
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Display hardware is part of this SOC, and we need to be able
to set certain variables in devicetree.cb. This chip file
contains the initial things we think we need to set.
Change-Id: I16f2d4228c87116dbeb53a3c9f3f359a6444f552
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3031
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This was a first pass at display port support, we have
realized that it was ultimately a bad path. The display
hardware is intimately tied into a specific cpu and
mainboard combination, and the code has to be elsewhere.
The devicetree formatting is ugly, but it matters not:
it's changing soon.
Change-Id: Iddce54f9e7219a7569315565fac65afbbe0edd29
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3029
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Based on comments in cpu/x86/msr.h for wrmsr/rdmsr, and for symmetry,
I have added __attribute__((always_inline)) for these.
Change-Id: Ia0a34c15241f9fbc8c78763386028ddcbe6690b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2898
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
If ROM caching is selected the haswell CPU initialization code
will enable ROM caching after all other CPU threads are brought
up.
Change-Id: I75424bb75174bfeca001468c3272e6375e925122
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3016
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The MP code on haswell was mirroring the BSPs MTRRs. In addition it
was cleaning up the ROM cache so that the MTRR register values were
the same once the OS was booted. Since the hyperthread sibling of
the BSP was going through this path the ROM cache was getting torn
down once the hyperthread was brought up.
That said, there was no differnce in observed boot time keeping the
ROM cache enabled.
Change-Id: I2a59988fcfeea9291202c961636ea761c2538837
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3008
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The haswell code was using the old assumption of which MTRR
was used for the ROM cache. Now that there is an API for doing
this use it as the old assumption is no longer valid.
Change-Id: I59ef897becfc9834d36d28840da6dc4f1145b0c7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3007
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
On certain architectures such as x86 the bootstrap processor
does most of the work. When CACHE_ROM is employed it's appropriate
to ensure that the caching enablement of the ROM is disabled so that
the caching settings are symmetric before booting the payload or OS.
Tested this on an x86 machine that turned on ROM caching. Linux did not
complain about asymmetric MTRR settings nor did the ROM show up as
cached in the MTRR settings.
Change-Id: Ia32ff9fdb1608667a0e9a5f23b9c8af27d589047
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2980
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I did not check what was once after the 'and'.
Change-Id: I9f3f725bec281a94abdb2eeb692a96fecdebcc0c
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/2999
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Previously southbridge_smm_init() was provided that did both
the clearing of the SMM state and enabling SMIs. This is
troublesome in how haswell machines bring up the APs. The BSP
enters SMM once to determine if parallel SMM relocation is possible.
If it is possible the BSP releases the APs to do SMM relocation.
Normally, after the APs complete the SMM relocation, the BSP would then
re-enter the relocation handler to relocate its own SMM space.
However, because SMIs were previously enabled it is possible for an SMI
event to occur before the APs are complete or have entered the
relocation handler. This is bad because the BSP will turn off parallel
SMM save state. Additionally, this is a problem because the relocation
handler is not written to handle regular SMIs which can cause an
SMI storm which effectively looks like a hung machine. Correct these
issues by turning on SMIs after all the SMM relocation has occurred.
Change-Id: Id4f07553b110b9664d51d2e670a14e6617591500
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2977
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds a new function to configure L2 cache for the
exynos5250 and deprecates the old function.
Change-Id: I9562f3301aa1e2911dae3856ab57bb6beec2e224
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2949
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Gabe Black <gabe.black@gmail.com>
Tested-by: build bot (Jenkins)
|
|
There is an optimization that can take place when hole
carving in ranges above 4GiB. If the range is the last
range then there is no need to carve UC holes out from
the larger WB range.
This optimization also has the same assumption of choosing
WB as the default MTRR type: the OS needs to properly
handle accessing realloacted MMIO resources with PAT so
that the MTRR type can be overidden.
Below are results using a combination of options. The
board this was tested on has 10 variable MTRRs at its
disposal. It has 4GiB of RAM.
IO hole config #1: hole starts at 0xad800000
No CACHE_ROM and no WRCOMB resources (takes 4 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x0000000100000000 size 0x52800000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 4/6.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007fc0000000 type 0
No CACHE_ROM and 1 WRCOMB resource (takes 6 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 6/7.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0
CACHE_ROM and no WRCOMB resources (takes 7 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000ff800000 size 0x52000000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 11/7.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6
MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6
MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 5 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 6 base 0x0000000100000000 mask 0x0000007f00000000 type 6
CACHE_ROM and 1 WRCOMB resource (takes 8 MTRRs):
Previously this combination was impossible without the optimization.
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 12/8.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6
MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6
MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 5 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 6 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 7 base 0x0000000100000000 mask 0x0000007f00000000 type 6
IO hole config #1: hole starts at 0x80000000
No CACHE_ROM and no WRCOMB resources (takes 1 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x0000000100000000 size 0x80000000 type 0
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 1/2.
MTRR: WB selected as default type.
MTRR: 0 base 0x0000000080000000 mask 0x0000007f80000000 type 0
No CACHE_ROM and 1 WRCOMB resource (takes 3 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 4/3.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 2 base 0x0000000100000000 mask 0x0000007f00000000 type 6
CACHE_ROM and no WRCOMB resources (takes 3 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000ff800000 size 0x7f800000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 9/3.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 2 base 0x0000000100000000 mask 0x0000007f00000000 type 6
CACHE_ROM and 1 WRCOMB resource (takes 4 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 10/4.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 2 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 3 base 0x0000000100000000 mask 0x0000007f00000000 type 6
Change-Id: Ia3195af686c3f0603b21f713cfb2d9075eb02806
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2959
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some ranges would use less variable MTRRs if an UC area
can be carved off the top of larger WB range. Implement this
approach by doing 3 passes over each region in the addres space:
1. UC default type. Cover non-UC and non-WB regions with respectie type.
Punch UC hole at upper end of larger WB regions with WB type.
2. UC default type. Cover non-UC regions with respective type.
3. WB default type. Cover non-WB regions with respective type.
The hole at upper end of a region uses the same min alignment of 64MiB.
Below are results using a combination of options. The board this was
tested on has 10 variable MTRRs at its disposal. It has 4GiB of RAM.
IO hole config #1: hole starts at 0xad800000
No CACHE_ROM or WRCOMB resources (takes 4 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x0000000100000000 size 0x52800000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 4/9.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007fc0000000 type 0
No CACHE_ROM. 1 WRCOMB resource (takes 6 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 6/10.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0
CACHE_ROM and no WRCOMB resources (taks 10 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000ff800000 size 0x52000000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
MTRR: default type WB/UC MTRR counts: 11/10.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x0000000080000000 mask 0x0000007fe0000000 type 6
MTRR: 2 base 0x00000000a0000000 mask 0x0000007ff0000000 type 6
MTRR: 3 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 4 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 5 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 6 base 0x0000000100000000 mask 0x0000007fc0000000 type 6
MTRR: 7 base 0x0000000140000000 mask 0x0000007ff0000000 type 6
Taking a reserved OS MTRR.
MTRR: 8 base 0x000000014f600000 mask 0x0000007fffe00000 type 0
Taking a reserved OS MTRR.
MTRR: 9 base 0x000000014f800000 mask 0x0000007fff800000 type 0
A combination of CACHE_ROM and WRCOMB just won't work.
IO hole config #2: hole starts at 0x80000000:
No CACHE_ROM or WRCOMB resources (takes 1 MTRR):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x0000000100000000 size 0x80000000 type 0
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 1/5.
MTRR: WB selected as default type.
MTRR: 0 base 0x0000000080000000 mask 0x0000007f80000000 type 0
No CACHE_ROM. 1 WRCOMB resource (takes 4 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 4/6.
MTRR: WB selected as default type.
MTRR: 0 base 0x0000000080000000 mask 0x0000007fc0000000 type 0
MTRR: 1 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0
MTRR: 2 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 3 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0
CACHE_ROM and no WRCOMB resources (takes 6 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000ff800000 size 0x7f800000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 9/6.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 2 base 0x0000000100000000 mask 0x0000007f80000000 type 6
MTRR: 3 base 0x000000017ce00000 mask 0x0000007fffe00000 type 0
MTRR: 4 base 0x000000017d000000 mask 0x0000007fff000000 type 0
MTRR: 5 base 0x000000017e000000 mask 0x0000007ffe000000 type 0
CACHE_ROM and 1 WRCOMB resource (takes 7 MTRRs):
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x0000000080000000 size 0x7ff40000 type 6
0x0000000080000000 - 0x00000000d0000000 size 0x50000000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x00000000ff800000 size 0x1f800000 type 0
0x00000000ff800000 - 0x0000000100000000 size 0x00800000 type 5
0x0000000100000000 - 0x000000017ce00000 size 0x7ce00000 type 6
MTRR: default type WB/UC MTRR counts: 10/7.
MTRR: UC selected as default type.
MTRR: 0 base 0x0000000000000000 mask 0x0000007f80000000 type 6
MTRR: 1 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 2 base 0x00000000ff800000 mask 0x0000007fff800000 type 0
MTRR: 3 base 0x0000000100000000 mask 0x0000007f80000000 type 6
MTRR: 4 base 0x000000017ce00000 mask 0x0000007fffe00000 type 0
MTRR: 5 base 0x000000017d000000 mask 0x0000007fff000000 type 0
MTRR: 6 base 0x000000017e000000 mask 0x0000007ffe000000 type 0
Change-Id: Iceb9b64991accf558caae2e7b0205951e9bcde44
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2925
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Downstream payloads may need to take advantage of caching the
ROM for performance reasons. Add the ability to communicate the
variable range MTRR index to use to perform the caching enablement.
An example usage implementation would be to obtain the variable MTRR
index that covers the ROM from the coreboot tables. Then one would
disable caching and change the MTRR type from uncacheable to
write-protect and enable caching. The opposite sequence is required
to tearn down the caching.
Change-Id: I4d486cfb986629247ab2da7818486973c6720ef5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2919
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The CONFIG_CACHE_ROM support in the MTRR code allocates an MTRR
specifically for setting up write-protect cachine of the ROM. It is
assumed that CONFIG_ROM_SIZE is the size of the ROM and the whole
area should be cached just under 4GiB. If enabled, the MTRR code
will allocate but not enable rom caching. It is up to the callers
of the MTRR code to explicitly enable (and disable afterwards) through
the use of 2 new functions:
- x86_mtrr_enable_rom_caching()
- x86_mtrr_disable_rom_caching()
Additionally, the CACHE_ROM option is exposed to the config menu so
that it is not just selected by the chipset or board. The reasoning
is that through a multitude of options CACHE_ROM may not be appropriate
for enabling.
Change-Id: I4483df850f442bdcef969ffeaf7608ed70b88085
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2918
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All resources that set the IORESOURCE_WRCOMB attribute which are
also marked as IORESOURCE_PREFETCH will have a MTRR set up that
is of the write-combining cacheable type. The only resources on
x86 that can be set to write-combining are prefetchable ones.
Change-Id: Iba7452cff3677e07d7e263b79982a49c93be9c54
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2892
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The old MTRR code had issues using too many variable
MTRRs depending on the physical address space layout dictated
by the device resources. This new implementation calculates
the default MTRR type by comparing the number of variable MTRRs
used for each type. This avoids the need for IORESOURE_UMA_FB
because in many of those situations setting the default type to WB
frees up the variable MTTRs to set that space to UC.
Additionally, it removes the need for IORESOURCE_IGNORE_MTRR
becuase the new mtrr uses the memrange library which does merging
of resources.
Lastly, the sandybridge gma has its speedup optimization removed
for the graphics memory by writing a pre-determined MTRR index.
That will be fixed in an upcoming patch once write-combining support
is added to the resources.
Slight differences from previous MTRR code:
- The number of reserved OS MTRRs is not a hard limit. It's now advisory
as PAT can be used by the OS to setup the regions to the caching
policy desired.
- The memory types are calculated once by the first CPU to run the code.
After that all other CPUs use that value.
- CONFIG_CACHE_ROM support was dropped. It will be added back in its own
change.
A pathological case that was previously fixed by changing vendor code
to adjust the IO hole location looked like the following:
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
As noted by the output below it's impossible to accomodate those
ranges even with 10 variable MTRRS. However, because the code
can select WB as the default MTRR type it can be done in 6 MTRRs:
MTRR: default type WB/UC MTRR counts: 6/14.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0
Change-Id: Idfcc78d9afef9d44c769a676716aae3ff2bd79de
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2889
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This moves the ram resource allocation into cpu_init() so that we
no longer rely on declaring a domain in devicetree.cb (which is kind
of weird for this platform). This does not cause any actual changes
to the coreboot memory table, and paves the way for further updates
to Snow's devicetree.
Change-Id: I141277f59b5d48288f409257bf556a1cfa7a8463
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2923
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This reverts commit 9427ca151e44644238b1b52138894195a9f5175f
Looks like we were a bit too anxious to see this one get in. The devicetree.cb change seems to have broken things.
coreboot memory table:
0. 0000000050000000-000000005000ffff: RESERVED
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
2. 0000014004000000-00000140044007ff: RESERVED
Before this patch:
coreboot memory table:
0. 0000000040000000-00000000bfefffff: RAM
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
Change-Id: I618e4f1976265d56cfd6a61d0c5736c55a0f3cec
Reviewed-on: http://review.coreboot.org/2914
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This does NOT turn on the graphics.
The device tree has been changed enough so that, at the very least, the correct
functions are called at the correct time, with the correct paramaters. We
decided to yank the I2C entries as they did not obvious function and might
not even have been correct.
Not working, seemingly, but we need to add a 4M resource for
memory, and it seems it needs to be fixed at the address shown.
This address was chosen from current hardware.
We realized that the display code should be part of the cpu -- that's how
the hardware works!
Change-Id: Ied65a554f833566be817540702f79a02e7b6cb6e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2615
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The amd_mtrr.c file contains a copy of the fixed MTRR algorithm.
However, the AMD code needs to handle the RdMem and WrMem attribute
bits in the fixed MTRR MSRs. Instead of duplicating the code
with the one slight change introduce a Kconfig option,
X86_AMD_FIXED_MTRRS, which indicates that the RdMem and WrMem fields
need to be handled for writeback fixed MTRR ranges.
The order of how the AMD MTRR setup routine is maintained by providing
a x86_setup_fixed_mtrrs_no_enable() function which does not enable
the fixed MTRRs after setting them up. All Kconfig files which had a
Makefile that included amd/mtrr in the subdirs-y now have a default
X86_AMD_FIXED_MTRRS selection. There may be some overlap with the
agesa and socket code, but I didn't know the best way to tease out
the interdependency.
Change-Id: I256d0210d1eb3004e2043b46374dcc0337432767
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2866
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I53982d88f94255abdbb38ca18f9d891d4bc161b0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2858
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Take the vboot path in romstage. This will complete the haswell
support for vboot firmware selection.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as
well by choosing the RO path.
Change-Id: Ie2b0a34e6c5c45e6f0d25f77a5fdbaef0324cb09
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2856
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Convert the existing haswell code to support reloctable ramstage
to use dynamic cbmem. This patch always selects DYNAMIC_CBMEM as
this option is a hard requirement for relocatable ramstage.
Aside from converting a few new API calls, a cbmem_top()
implementation is added which is defined to be at the begining of the
TSEG region. Also, use the dynamic cbmem library for allocating a
stack in ram for romstage after CAR is torn down.
Utilizing dynamic cbmem does mean that the cmem field in the gnvs
chromeos acpi table is now 0. Also, the memconsole driver in the kernel
won't be able to find the memconsole because the cbmem structure
changed.
Change-Id: I7cf98d15b97ad82abacfb36ec37b004ce4605c38
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Using the CPU microcode update script and
Intel's Linux* Processor Microcode Data File
from 2013-02-22
Change-Id: I9bb60bdc46f69db85487ba923e62315f6e5352f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2845
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Using the CPU microcode update script and
Intel's Linux* Processor Microcode Data File
from 2013-02-22
Change-Id: Icaf0e39978daa9308cc2f0c4856d99fb6b7fdffa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2844
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
for latest URL of their microcode tar ball
Change-Id: I3da2bdac4b2ca7d3f48b20ed389f6a47275d24fe
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2842
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These base addresses are used in several places and it
is helpful to have one location that is reading it.
Change-Id: Ibf589247f37771f06c18e3e58f92aaf3f0d11271
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2812
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The RESET_ON_INVALID_RAMSTAGE_CACHE option indicates what to do
when the ramstage cache is found to be invalid on a S3 wake. If
selected the system will perform a system reset on S3 wake when the
ramstage cache is invalid. Otherwise it will signal to load the
ramstage from cbfs.
Change-Id: I8f21fcfc7f95fb3377ed2932868aa49a68904803
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2807
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Cache the relocated ramstage into the SMM region. There is
a reserved region within the final SMM region (TSEG). Use that
space to cache the relocated ramstage program. That way, on S3 resume
there is a copy that can be loaded quickly instead of accessing the
flash. Caching the ramstage in the SMM space is also helpful in that
it prevents the OS from tampering with the ramstage program.
Change-Id: Ifa695ad1c350d5b504b14cc29d3e83c79b317a62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2806
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The SMM region is available for multipurpose use before the SMM
handler is relocated. Provide a configurable sized region in the
TSEG for use before the SMM handler is relocated. This feature is
implemented by making the reserved size a Kconfig option. Also
make the IED region a Kconfig option as well. Lastly add some sanity
checking on the Kconfig options.
Change-Id: Idd7fccf925a8787146906ac766b7878845c75935
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2804
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The TSEG region is accessible until the SMM handler is relocated
to that region. Set the region as cacheable in romstage so that it
can be used for other purposes with fast access.
Change-Id: I92b83896e40bc26a54c2930e05c02492918e0874
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2803
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The haswell processors support the ability to save their SMM state
into MSR space instead of the memory. This feaure allows for parallel
SMM relocation handlers as well as setting the same SMBASE for each
CPU since the save state memory area is not used.
The catch is that in order determine if this feature is available the
CPU needs to be in SMM context. In order to implement parallel SMM
relocation the BSP enters the relocation handler twice. The first time
is to determine if that feature is available. If it is, then that
feature is enabled the BSP exits the relocation handler without
relocating SMBASE. It then releases the APs to run the SMM relocation
handler. After the APs have completed the relocation the BSP will
re-enter the SMM relocation handler to relocate its own SMBASE to the
final location. If the parallel SMM feature is not available the BSP
relocates its SMBASE as it did before.
This change also introduces the BSP waiting for the APs to relocate
their SMBASE before proceeding with the remainder of the boot process.
Ensured both the parallel path and the serial path still continue
to work on cold, warm, and S3 resume paths.
Change-Id: Iea24fd8f9561f1b194393cdb77c79adb48039ea2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2801
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that there is a way to disseminate the presence of s3 wake more
formally use that instead of hard coded pointers in memory and stashing
magic values in device registers. The northbridge code picks up the
field's presence in the romstage_handoff structure and sets up the
acpi_slp_type variable accordingly.
Change-Id: Ida786728ce2950bd64610a99b7ad4f1ca6917a99
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2799
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some of the functions called from assembly assume the standard
x86 32-bit ABI of passing all arguments on the stack. However,
that calling ABI can be changed by compiler flags. In order to
protect against the current implicit calling convention annotate
the functions called from assembly with the cdecl function
attribute. That tells the compiler to use the stack based parameter
calling convention.
Change-Id: I83625e1f92c6821a664b191b6ce1250977cf037a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2794
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that CONFIG_RELOCTABLE_RAMSTAGE is available support it on
Haswell-based systems. This patch is comprised of the following changes:
1. Ensure that memory is not preserved when a relocatable ramstage is
enabled. There is no need.
2. Pick the proper stack to use after cache-as-ram is torn down. When
the ramstage is relocatable, finding a stack to use before vectoring
into ramstage is impossible since the ramstage is a black box with an
unknown layout.
Change-Id: I2a07a497f52375569bae9c994432a8e7e7a40224
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2793
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
