| Age | Commit message (Collapse) | Author |
|---|
|
Pointer to an empty string (filled with spaces) is
stored inside GNVS. Rearrange things to avoid having
<chromeos/gnvs.h> in SMBIOS code.
Change-Id: I9405afbea29b896488b4cdd6dd32c4db686fe48c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49281
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
|
|
It would seem that `pres` is an abbreviation for `presence`. Personally,
over the last ~2.5 years, I have seen checkpatch complaints about `pres`
on several occasions, and all of them were abbreviations for `presence`.
Given the high false positive rate for this entry, comment it out.
Change-Id: I72f1811fb1f766e7de7c4957fd9ba844c0728029
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49463
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: Ie122a441145383b820d96e32ce1581dfc27fa57b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
They all operate on that file, so just add it globally.
Change-Id: I953975a4078d0f4a5ec0b6248f0dcedada69afb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Now that intermediate coreboot.pre manipulation is serialized within
the build system, remove the flock calls.
Change-Id: I8a767918aec5fcb7127ebb19ac46e58bed7967fb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
We no longer need the IO-APIC assignments since we use the GNB IO-APIC.
We were also missing the E-H IRQ mapping. I also renumbered them since
IRQ 8 is used by the rtc.
TEST=none
BRANCH=zork
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia956ae457669aeda6fa49e127373aad3807f7b9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enhance USB 2.0 M/B C0, DB C1 A1 port:
HS DC Voltage Level(TXVREFTUNE0): 0xe
COMPDISTUNE(COMPDISTUNE0): 0x7
BUG=b:165209698
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I371e4295c2ee161096f0a277c0c649bf217269b2
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
1. Modify STAPM time constant 2500 to 1400.
2. Add telemetry setting:
VDD Slope : 30518
VDD Offset: 435
SOC Slope : 22965
SOC Offset: 165
BUG=b:177399751
BRANCH=master
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I251029389c10ee0f17f368b1c00ac666d372fc3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Hynix DDR4 DRAM H5ANAG6NCJR-XNC, index was generated by gen_part_id
BUG=b:176313722
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Ia1947fa158a1113c4a0b1a0d55f657ddaac43382
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Two configuration files are added:
1. H9HCNNNFAMMLXR-NEE-8GB: new byte mode
2. MT53E1G32D2NP-046-4GB: new single rank mode
Also initialize the rank number field 'rank_num' for all configs.
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: I1786c1e251e8d6e110cbdce79feeb386db220404
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49108
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add emi setting to support byte mode and single rank ddr sample
2. Modify initial setting for DDR with different architecture
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: Id2845b2b60e2c447486ee25259dc6a05a0bb619b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The fw_config field SPI_SPEED is not used for zork devices.
To define SAR config, use the fw_config bit[23..26].
Then vilboz can loaded different WiFi SAR table for different SKUs.
BUG=b:176858126, b:176751675, b:176538384
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5ba98799e697010997b515ee88420d0ac14ca7ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add code to collect all required information and generate ACPI CRAT
table entries. Publish tables generated from cb, rather than use the
tables created by FSP binary.
BUG=b:155307433
TEST=Boot trembyle and compare coreboot generated tables with tables
that FSP published previously.
BRANCH=Zork
Change-Id: If64fd624597b2ced014ba7f0332a6a48143c0e8c
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Based on voema schematics, two USB2 ports 3 and 5 are assigned to type C
connectors on Voema board.
BUG=b:177483061 b:172535001
TEST=Build and boot Voema.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I12cef85595e511801ab9c563ae4aa26e25875679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Do LPC/eSPI pad configuration at board-level to match other platforms.
Early gpio configuration was done in romstage, while LPC pads were
configured in bootblock. Instead of adding another dedicated gpio table
for bootblock, move early gpio configuration completely to bootblock on
these boards. This won't hurt, since there is no code touching the pads
in between.
The soc code gets dropped in CB:49410.
Change-Id: I2a614afb305036b0581eac8ed6a723a3f80747b3
Tested-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Command timing is the absolute value of the most negative `pi_coding`
value across all ranks, or zero if there are no negative values. Use the
MAX() macro to ease proving that `cmd_delay` can never be negative, and
then drop the always-false underflow check.
The variable type for `cmd_delay` still needs to be signed because of
the comparisons with `pi_coding`, which is a signed value. Using an
unsigned type would result in undefined and also undesired behavior.
Change-Id: I714d3cf57d0f62376a1107af63bcd761f952bc3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Clock is a differential signal and propagates faster than command and
control, therefore its timing needs to be offset with `pi_code_offset`.
It is also a periodic signal, so it can safely wrap around.
To avoid potential undefined behavior, make `clk_delay` signed. It makes
no difference with valid values, because the initial value can be proven
to never be negative and `pi_code_offset` is always positive. With this
change, it is possible to add an underflow check, for additional sanity.
Change-Id: I375adf84142079f341b060fba5e79ce4dcb002be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 7584e550cc (nb/intel/sandybridge: Clean up program_timings)
introduced this condition along with a comment that says the opposite.
Command and clock timings always need to be computed, so drop both the
nonsensical condition and the equally-worthless corresponding comment.
Change-Id: I509f0f6304bfb3e033c0c3ecd1dd5c9645e004b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 does not change.
Change-Id: I0ca98cbe45e10d233607f68923f08752fdda9698
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46923
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Basking Ridge is not ULT, thus does not support C-states deeper than C7.
Replace them with the values used by all other Haswell non-ULT boards to
allow subsequent commits to cleanly factor them out of the devicetree.
Change-Id: Ife34f7828f9ef19c8fccb3ac7b60146960112a81
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46907
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module is not expected to be powered off during warm reset. Hence
configure the LTE_PWR_OFF_ODL (GPP_A10) gpio pad reset configuration to
PWROK and set the TX state to 1.
BUG=b:163100335
BRANCH=dedede
TEST=Verified through the waveforms that power sequence is meeting the LTE module requirements.
Change-Id: I8676da6186559288aabe078b6158fc01075c7b41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Exit early if the chipset power state info isn't in CBMEM. Return -1 in
order to ensure the one caller of this function exits early as well.
Found-by: Coverity CID 1442304
Change-Id: Ifa42ba3024d3144de486d90ed7752820482549bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49359
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module used in metaknight has a specific power on/off sequence.
GPIOs related to power sequence are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: GPP_A10 keeps high, GPP_H17 goes low at least 2ms
Configure the GPIOs based on these requirements.
BUG=b:173671094
TEST=Build and boot Metaknight to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ibff16129dfe2f1de2b1519049244aba4b3123e52
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Use C-style comments everywhere, and follow the coding style.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I3ef96c5f6553ad50cee7d7f5614128b62a89e4ea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The caches have already been enabled during MP-init,
so these function calls are redundant. Remove them.
Change-Id: Ia9be1a3388d8e7c73c35a1c68b3dd5bc488658c2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fix C code to match comment and assembly implementation.
Tested on Prodrive hermes:
The microcode spinlock is no longer used.
Change-Id: I21441299f538783551d4d5ba2b2e7567e152d718
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49304
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change affects Intel CPUs only. As most platforms are doing
uCode update using FIT, they aren't affected by this code either.
Update microcode in MP-init using a single spinlock when running on
a Hyper-Threading enabled CPU on pre FIT platforms.
This will slow down the MP-init boot flow.
Intel SDM and various BWGs specify to use a semaphore to update
microcode on one thread per core on Hyper-Threading enabled CPUs.
Due to this complex code would be necessary to determine the core #ID,
initializing and picking the right semaphore out of CONFIG_MAX_CPUS / 2.
Instead use the existing global spinlock already present in MPinit code.
Assuming that only pre-FIT platforms with Hyper-Threading enabled and at
most 8 threads will ever run into this condition, the boot delay is
negligible.
This change is a counterproposal to the previous published patch series
being much more unsophisticated.
Change-Id: I27bf5177859c12e92d6ce7a2966c965d7262b472
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Eaglelake MRC 2.55 does this, and also stalls for less time.
Change-Id: Iaaefd32c341a490e5c129df865407ec3f8da8212
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
To allow other platforms to reuse this code, extract it into a separate
compilation unit. Since HPET is enabled through the southbridge, place
the code in the southbridge scope. Finally, select the newly-added
Kconfig option from i82801gx and replace lpc.c `enable_hpet` function.
Change-Id: I7a28cc4d12c6d79cd8ec45dfc8100f15e6eac303
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On Coffee Lake systems prog_locate_hook() is called with PROG_POSTCAR.
For this reason the early check is not executed.
Add check for prog->type == PROG_POSTCAR, but execute
verified_boot_early_check() once.
BUG = N/A
TEST = Build and boot on Facebook FBG1701 and Intel CoffeeLake system
Change-Id: Ia3bd36064bcc8176302834c1e46a225937d61c20
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48852
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
make olddefconfig on other projects using USE_VENDORCODE_ELTAN results in error.
USE_VENDORCODE_ELTAN unmet direct dependencies.
Remove dependency on VBOOT for USE_VENDORCODE_ELTAN.
TEST = Build and boot on Facebook FBG1701
Change-Id: I5881c334955c73ae0f1a693f95ceb1aee62ee898
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
TEST=call do_board_reset() manually.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I355f71e731f1045cd80a133cd31cf4d55f14d91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This struct isn't used anywhere else, so there's no need to name it.
Change-Id: I22eda07f14096d2b7400e6ab715641ffd68fbc08
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49444
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The default value is not sufficient to correctly configure the Type-C
ports as it has all ports disabled by default. On Volteer ports 0
and 1 are enabled so setting this value to 0x3 and correctly
keeping the IomPortPadCfg values at 0 for ports that have a
retimer and ports that are not configured. These values were set
to 0x90000000 to avoid s0ix issues which arose from the UsbTcPortEn
value being incorrect.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that s0ix cycles complete
without any issues
Change-Id: Ib4f2bd0f68debd4e97ccaab9e1d8a873dc4e4d9f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48814
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a requirement of TCSS this setting needs to be correctly set
to determine what Type-C ports are enabled on the platform. Without
this value correctly set there can be adverse effects on the other
TCSS specific values.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that S0ix cycles no longer
fail when the IomPortPad is set to 0
Change-Id: I6c5260cda71041439fe89d15bd3cafd4052ef1e7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
These are no longer really useful. We can also enable Power Resource
ACPI debug in the kernel if we want these messages.
BUG=none
BRANCH=zork
TEST=emerge-zork and verify debug messages are no longer posted
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I936e816266825f1c59377c2e079ffe1a5188838c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Target added to INTERMEDIATE all operate on coreboot.pre, each modifying
the file in some way. When running them in parallel, coreboot.pre can be
read from and written to in parallel which can corrupt the result.
Add a function to create those rules that also adds existing
INTERMEDIATE targets to enforce an order (as established by evaluation
order of Makefile.inc files).
While at it, also add the addition to the PHONY target so we don't
forget it.
BUG=chromium:1154313, b:174585424
TEST=Built a configuration with SeaBIOS + SeaBIOS config files (ps2
timeout and sercon) and saw that they were executed.
Change-Id: Ia5803806e6c33083dfe5dec8904a65c46436e756
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49358
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie3188d36e8ecacab42818c8619122751fcb7cdf8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49379
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI part still needs some more code to be in place, so add that
later.
TEST=Together with the currently not merged rest of the amdfw patch
train applied this results in working serial console in bootblock in
Majolica.
Change-Id: Ia844e86a80c19026ac5b47a5a1e91c2553ea5cca
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49378
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d7574b60640eaf9a47a797e823324edeaf1e770
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: Ic6dcbe999234f233fbac8fbdb06d22c8577b1a40
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I1a01cc745c7049dc672bca12df5c6b764ac9b907
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since the functions that get called by the coreboot console
initialization code aren't in the SOC-specific code anymore, the SOC's
uart.c can be included unconditionally in the build now. This also
replaces the STONEYRIDGE_UART Kconfig option with the common
AMD_SOC_CONSOLE_UART one.
Change-Id: I09c15566a402895d6388715e8e5a802dc3c94fdd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5079decfae982d2222bb9a7f5155d51885d4d3a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49374
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will result in less code duplication when the common AMD SoC UART
support gets used for more AMD SoCs.
Change-Id: Id1786f32324de3e3947d792c599e2019705c5a85
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49373
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This partially reverts commit 6f8f9c969be9d471464f1b6a42b4bb1c2590db5c
by moving CONSOLE_UART_BASE_ADDRESS back to the SoC-specific code, since
the number and base addresses of UARTs turned out to be rather SoC-
specific. The help text for the AMD_SOC_CONSOLE_UART option also
contained those base addresses, so remove that as well.
Change-Id: I01211ec62421c56f22ed611313d6245a05bdea67
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The UARTs in the Picasso SoC are memory mapped, but there is also some
hardware support that isn't used by any board to make the UARTs behave
like the ones found on legacy x86 machines from the 90s.
In the MMIO mode the MMIO address of the UART controller is passed to
the OS via ACPI. The OS expects the base clock of the UART controller to
be 48MHz (see the cz_uart_desc struct in drivers/acpi/acpi_apd.c and
drivers/tty/serial/8250/8250_dw.c in the Linux kernel) in this case. It
is also possible to enable additional decodes from four 8 byte legacy
I/O locations used for serial ports to the different UART controllers,
which doesn't disable the MMIO access though. The legacy I/O-mapped
serial ports are usually expected to have a base clock of 16*115200Hz
which the hardware can also provide to the UART's baud rate generator.
So there are two possible valid configurations to use the UARTs; either
MMIO access in combination with a 48MHz base clock or the legacy I/O
decode with a ~1.8MHz base clock.
The existing code unconditionally generates ACPI objects for all enabled
UARTs, so those shouldn't be put into legacy mode and switching the base
clock to ~1.8MHz was only done in the case that the UART was used as
coreboot console UART which still used the MMIO access, but the lower
base clock. Since no board even selects this option and it's rather
invasive to properly implement this feature, just drop the corresponding
broken code.
TEST=SoC UART console still works on Mandolin.
Change-Id: I26fa8fdfc781b583ba56ac4dbcbbfb6100e84852
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49371
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update ELAN i2c-hid touchscreen configuration
BUG=b:172517685
BRANCH=dedede
TEST=Verify touchscreen is working fine on botenflex
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ia7c81fd0a772968ec32406f1e366a90481fc5ad8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Icf1571ae360cee5698626f0360e1408360e8a7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is causing boot errors on zork:
coreboot-v1.9308_26_0.0.22-18590-g4598a7bed945 Wed Dec 16 17:32:25 UTC 2020 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area FW_MAIN_B found @ 312000 (3137280 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1f2bbdd9c87c4efdfb0042e90a20b489fa0efced
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
While unused, this allows use of a common initialisation
code for GNVS allocation.
Change-Id: Ie84b5a3e16d3baa12bcd5dadac0b1f7edb323272
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I9971069803a7cd1b9be0ac0cfa410b6e1fdc3eeb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I61a9b07ec3fdaeef0622df82e106405f01e89a9e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48719
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic9cdcc497bf1a9f5bfed5e6d95040bfa602b0b89
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48732
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I515e830808a95eee3ce72b16fd26da6ec79dac85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48718
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace acpi_create_gnvs() under soc/ to reflect their
changed functionality.
Change-Id: I61010f64a4a935f238e6dcd0f8c1340a6cc68eb4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I80f92bed737904e6ffc858b45459405fe76f1d04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update PL1 min and max values for Delbin systems
BUG=b:168958222
BRANCH=None
TEST=Build and verify on delbin system
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: I2152f0dbeb0ae463b78464571b6c434830f0082a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
|
Allows us to build with `-Wmissing-prototypes`.
Change-Id: I722b41e515ee472697028a912b9136ce59611051
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47635
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The S3/S4 workaround is specific to Panther Point stepping A0, and it is
wrongly implemented. Rewrite the whole function as per reference code.
Since this runs in SMM, be overly cautious and double-check everything.
Do not rely on GNVS to determine if xHCI is enabled. Instead, check
whether the corresponding bit in the Function Disable register is set.
Only Panther Point has xHCI, so exit early if this is not the case.
Change-Id: Iabce6c52fac781dc694f5b589fab2e9fe438f3f5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:174338903
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I875f6b32c4053ef6d23ad7606cd35a129a78c306
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49290
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Compilation has been broken in commit I022468f6957415ae68a7a7e70428ae6f82d23b06
Adding a missing define solved this. See https://cgit.freebsd.org/src/tree/sys/sys/fcntl.h#n319
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I3433e4c9269880d3202dd494e5b2e962757a6b87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add registers from IT5570E datsheet v0.3.1.
Tested on Clevo L141CU.
Change-Id: Idc764c6180e235298835d7639fcb0b562a2c21a4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48922
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change lets IOM consider all USB connected devices as device
attached(DA) scenario. While connecting a typec-to-a dongle, IOM would
disable TC cold and help to resolve enemuration failure after usb3
device is plugged into the dongle.
BUG=b:173054070
TEST=Build and boot on delbin.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0ad0322693b4f8fbf1000b24eb21dddcebec686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The name `..._index` is confusing since the maximum index of an array is
not `ARRAY_SIZE(array)` but `ARRAY_SIZE(array) - 1`.
Rename `uart_max_index` to `uart_ctrlr_config_size` to make the name
match the variable´s value.
Change-Id: I7409c9dc040c3c6ad718abc96f268c187d50d79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Initiate overridetree.cb based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I31e5ac1703476083ac71dac30b0a3299b38384c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow latest schematic to fill gpio table.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a983605b5139ff8510a0cf225e6564b9215cb1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Two USB2 ports 4 and 9 are assigned to type C connectors on Voxel board.
This update configures these USB2 ports for Type C which will allow USB2
port reset message upstream from PCH to CPU to recover a USB3 device
that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Voxel board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia370a449a41701e690c1c507d70bedfce2076a65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
When building as part of the coreboot build system, use the same
mechanism as other tools (cbfstool, amdfwtool, ...) so that abuild
builds ifdtool once into sharedutils instead of once per board (while
avoiding other race conditions, too).
Change-Id: I42c7b43cc0859916174d59cba6b62630e70287fd
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
It is only used in one place, and there's two other equivalent macros.
Change-Id: I7c8241e28f688abd2df8180559dd02ee441c7023
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ie3c7c33096f60a5aa476ff55c538fe68ffadc068
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The bugs happen on real hardware or in qemu with KVM enabled.
The very same code runs on some real devices and it runs in qemu
with KVM disabled.
The bugs are so strange that no root cause could be found yet.
Change-Id: I01050f2e38f92c6b96e3258a5b619aa9ee685acc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Get rid of using eax and reload counter on race condition.
Change-Id: Ie4b9957d8aa1f272ff1db5caf2c69d1e1f086a03
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47714
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use same indents for switch/case to fix linter issues.
Change-Id: I5c6abf5b918bac3df8d7617824392f2ec932cb32
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Registers and their default values are from the datasheet ("IT8720F",
"Preliminary Specification V0.1").
Tested on an Acer G43T-AM3.
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Change-Id: I69987be4f5cb50b3c20f06733f30b308891d5ad0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This change adds a helper function `pcie_rp_enable_mask()` that
returns a 32-bit mask indicating the status (enabled/disabled) of PCIe
root ports (in the groups table) as configured by the mainboard in the
device tree.
With this helper function, SoC chip config does not need to add
another `PcieRpEnable[]` config to identify what root ports are
enabled.
Change-Id: I7ce5fca1c662064fd21f0961dac13cda1fa2ca44
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48968
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the definition of config_of_soc() to a macro that
expands to __pci_0_00_0_config instead of accessing the config
structure by referencing the struct device. This allows linker to
optimize out unused portions of the device tree from early stages.
With this change, bootblock .text section size drops as follows:
Platform | Size without change | Size with change | Reduction |
---------------|---------------------|------------------|-------------|
GLK (ampton) | 27112 bytes | 9832 bytes | 17280 bytes |
APL (reef) | 26488 bytes | 17528 bytes | 8960 bytes |
TGL (volteer2) | 47760 bytes | 21648 bytes | 26112 bytes |
CML (hatch) | 40616 bytes | 22792 bytes | 17824 bytes |
JSL (waddledee)| 37872 bytes | 19408 bytes | 18464 bytes |
KBL (soraka) | 31840 bytes | 21568 bytes | 10272 bytes |
As static.h is now included in device.h which gets pulled in during
the unit tests, a dummy static.h is added under tests/include.
Change-Id: I1fbf5b9817065e967e46188739978a1cc96c2c7e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TEST=Able to build and boot ADLRVP.
Change-Id: Ia331998b46abcf10e939078dea992589f09139bd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49301
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
By default, the HS400 mode of GL9763E is slow mode (150MHz).
Therefore, the slow mode is disabled for HS400 running at 200MHz.
For eMMCs such as Hynix (H26M74002HMR) on HS400, adjust the internal
Rx latch dealy of HS400 to have better compatibility.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Change-Id: I84844c2432d4223d9929182c5c430915e52875b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The FW config takes 2 bits for USE_FAN[27,28].
So FW_CONFIG_SHIFT_WWAN value should be 29.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ica6d04f9c48aa0800189283608bf57416ac75cf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49236
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 542307b815 (broadwell: Add small delay before Flex Ratio reboot)
introduced a workaround for Broadwell. Implement it on Haswell as well.
Since this is only necessary when a TPM is present on a system, only do
the delay (which is not that small, to be honest) on TPM-enabled builds.
Change-Id: Id8b58e9fa2a1c81989305f5b4b765b82c01e1596
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46941
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Apply commit ff0f460e76 (broadwell: Add configuration for tuning VR
for C-state operations) to Haswell, in preparation for unification.
Change-Id: Ib05974e8ed0f73c4f475b90065e8efb14555f9c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46920
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Haswell reference code version 1.9.0 uses the same value as Broadwell.
Change-Id: I979ea1b4ba2962bd0c55cfb9d0c291f32cf5fcad
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46919
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 7f28e4ee01 (broadwell: Enable turbo ratio if available) is also
applicable to Haswell, since the MSR definitions are the same for both.
Change-Id: Ic5f30a5b06301449253bbfb9ed58c6b35a767763
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46918
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The MSR only needs to be set when IO MWAIT redirection is to be enabled.
This was copied from Sandy Bridge, which already had this inconsistency.
Change-Id: I424333afd654db9a7e180e9a2c31d369e3d92fd6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46917
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It either doesn't exist (in-tree builds) or is the same as $_LIBDIR.
Change-Id: I9551cbfc3295d86c22a3785be7cdc0f65eeb08c4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47632
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We only need `$_OBJ` in the include path for in-tree builds. Also,
curses only need special handling for those and PDCurses turned out
to need many more include paths.
Change-Id: Idd29ef33065033e26ba61b09d412d8ca3566d643
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add $_DOTCONFIG and $_XCOMPILE pointing to the respective files and
use them.
Change-Id: I719b42d1c8abf055948daf5b000daa30cd249edd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:171757619
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I37390535e263b4b9547ad7307278e3360ba836bd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Booting on Kingston (EMMC64G-TA29/TX29-HP) and Hynix (H26M74002HMR) eMMC
currently fails due to R/W error. This is a workaround to finetune the
data latch timing by verdor-specific setting of GL9763E. For improving
the compatibility of GL9763E with these two eMMC.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Change-Id: Iddb145ed6a9edb2d7a50248e64659cda78b88ae6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add SLP_S0 residency register and enable LPIT support.
Change-Id: Id1abbe8dcb7796eeb26ccb72f1f26cf7a040dba4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49048
Reviewed-by: Lance Zhao
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
Change-Id: Icccd9d15a9e9a22c9bfe7a9843e95d77013c9c8f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49047
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi
- Linux tested on clevo/cml-u
Change-Id: I51fdf52419aa7f059b70a906fd8bdac88d5b6046
Tested-By: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49046
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for the Intel LPIT table to support reading Low Power Idle
Residency counters by the OS. On platforms supporting S0ix sleep states
there can be two types of residencies:
* CPU package PC10 residency counter (read from MSR via FFH interface)
* PCH SLP_S0 assertion residency counter (read via memory mapped
interface)
With presence of one or both of these counters in the LPIT table, Linux
dynamically adds the corresponding attributes to the cpuidle sysfs
interface, that can be used to read the residency timers:
* /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
* /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
The code in src/acpi implements generic LPIT support. Each SoC or
platform has to implement `acpi_fill_lpit` to fill the table with
platform-specific LPI state entries. This is done in this change for
soc/intel/common, while being added as its own compilation unit, so SoCs
not yet using common acpi code (like Skylake) can use it, too.
Reference:
https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi together with CB:49046
- Linux tested on clevo/cml-u, supermicro/x11ssmf together with CB:49046
Change-Id: I816888e8788e2f04c89f20d6ea1654d2f35cf18e
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:176536593
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wayne3_Wang <wayne3_wang@pegatron.corp-partner.google.com>
Change-Id: I69962a5b7c7c464280b35c834f7ee1c9b77db6fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49197
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change emits chip config pointers for PCI devices on root bus in
static_devices.h so that the config structure can be accessed directly
without having to reference the device structure. This allows the
linker to optimize out unused parts of the device tree from early
stages like bootblock.
Change-Id: I1d42e926dbfae14b889ade6dda363d8607974cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49214
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
