| Age | Commit message (Collapse) | Author |
|---|
|
By default all Intel platform has enable IO decode range for COMA if
CONFIG_DRIVERS_UART_8250IO is selected.
With this patch, COMB will get enable based on
CONFIG_SOC_INTEL_COMMON_BLOCK_LPC_COMB_ENABLE Kconfig selection.
Also make lpc_enable_fixed_io_ranges() function returns Enabled I/O bits to avoid
an additional pci configuration read to get the same data.
Change-Id: I884dbcc8a37cf8551001d0ca61910c986b903ebc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Change SECONDARY_SPD_SOURCES to SEC_SPD_SOURCES as that is what the
spd target expects.
TEST=Verified that sec-spd.bin is present in coreboot.rom
Change-Id: I4299df1eb9009095ef899c5b83823750dfc715d8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Prints the timestamp name and value to the debug console if enabled
in Kconfig.
Change-Id: Ie6e6a4877fefec45fb987ceae7d42de6ce768159
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
In preparation for moving AGESA calls out of bootblock:
Add function to enable the four stoneyridge I2C engines.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt (with other changes
to call code not committed at this time)
Change-Id: Icb55c49cf56c65a9c2e1838cff1ed5afc04e1826
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25026
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation for moving AGESA calls out of bootblock:
* Add definitions for needed registers in southbridge.h
* Add function to enable AMD FCH ACPI MMIO regions 0xfed80000 to
0xfed81ffff. Will be called by a later commit.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build boot Grunt (with other changes
to call code not committed at this time)
Change-Id: If26efa6c6f5b562ba898e7d9da4827833310dc26
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25025
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP can only output its traces when the HSUART PCI device is
available.
- Move the hiding to after last FSP call.
- Adapt coreboot PCI enumeration to keep the legacy configuration.
With UART configured as legacy Linux will not re-enumerate it but detects
it as legacy (ttyS0 instead of ttyS4).
Change-Id: Id8801e178ffd8eeee78ece07da7bd6b8dbd88538
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
GPIO 40 isn't currently being used, so set it to be an input.
BUG=b:73387647
TEST=Build & boot grunt
Change-Id: I5a04cbab1276cd20e7f9c7576e8111089dd2b155
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Bayhub part is not used on proto with board_id 0, so disable it.
BUG=b:74248569
TEST=Build & boot Grunt. Bayhub part is disabled.
Change-Id: I635356d41bab637726594d403d66dde730f12256
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Update build so that we can get the board ID in bootblock.
BUG=b:74248569
TEST=build and boot grunt with follow-on patch.
Bayhub part is disabled.
Change-Id: I6353bcb4abcef4e8dc2b625082e33b73525c8525
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since the timeout in bsp_do_flight_plan is bumped up to 1 second, this
change adds a print to indicate the amount of time it takes for all the
APs to check-in.
TEST=Verified on Nami that it prints:
"bsp_do_flight_plan done after 395 msecs."
Change-Id: I4c8380e94305ed58453ed18b341b3b923949d7a8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Return proper SKU IDs so that mosys can return the proper variant.
BUG=b:74059798
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I665fa491de6e277fea5cc071b1f04a21317bccba
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX
IOMMU and the general IOMMU respectively. These addresses have to be
configured in MCHBAR registers and reserved from the OS.
GFXVTBAR/VTVC0BAR policy registers set to be consistent with
proprietary vendor firmwares on hardware of same platform
(2 different vendor firmwares compared, found to be identical).
Change-Id: Ib8f2fed9ae08491779e76f7d1ddc1bd3eed45ac7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24983
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This #define tells superio.asl to add a "PNP0501" "Plug and Play
16550A-compatible COM port" entry to kahlee's ACPI tables.
The EC on kahlee boards do not provide a "Serial Port 1" that should
be exposed via ACPI to the OS. In fact, this entry confuses the
kernel and in some cases can cause it to try to redirect output to a
non existing port.
BUG=b:74200887
TEST=Deploy to grunt. Boot kernel with SERIAL_PORT_DFNS undefined and
"earlycon=uart,mmio32,0xfedc6000,115200,48000000" on the kernel
command line, and with an image with serial console enabled.
=> System boots with (kernel) serial console enabled, starting from
0.00 (earlycon), with no gaps in its output, and serial console
also allows logging in.
Change-Id: I0eaed9b4461bb6a6c1aa4ce97752f588d4322b35
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move call to __gspi_cs_change() in gspi_ctrlr_setup() to after
initialization of cs polarity since it requires polarity to be
set to work properly. Failure to do so confuses cr50.
BUG=b:70628116
BRANCH=chromeos-2016.05
TEST='emerge-meowth coreboot' and verify on scope that chip select
polarity is correct for the first transaction.
Change-Id: I20b4f584663477d751a07889bccc865efbf9c469
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
coreboot's PCI resource allocator doesn't assign BAR1 for
Braswell's LPE device because it doesn't exist, but is
required by Windows drivers for the device to function.
Manually add the required resource via the existing
lpe_read_resources function, and marked it as IORESOURCE_STORED
so pci_dev_set_resources ignores it.
TEST: boot Windows 10 on google/edgar, observe that memory resources
are properly assigned to LPE driver for BAR1 and no error reported.
Change-Id: Iaa68319da5fb999fe8d73792eaee692cce60c8a2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add timestamps before and after the vBIOS load and after the vBIOS
run. This lets us see exactly how long it took to load it from the
ROM chip, and how long it takes to run.
BUG=b:64549506
TEST=Build & boot Grunt, see vBIOS load & initialization times.
Change-Id: I878ba653eb086ad6c6614aa08a6d3fe216a9323e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25018
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CBI abbreviates Cros Board Info.
BUG=b:74177699
BRANCH=master
TEST=Verify CPU log shows expected SKU ID on Nami.
Change-Id: I42dd177de8c49cf3c122c2ebb1fcf42e5ba4cd75
Signed-off-by: amanda_hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/24996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Hardware updates have suggested we need to configure the K&D panel's
power sequence in software, not in hardware. Without this change, K&D
panels will no longer power on correctly and will instead display a
black screen.
Per K&D's suggestion, we tweak these two commands. From the little HW
docs I have, this looks like it's:
(Address 0xB7, Value 0x02) -> set BC_CTRL=bit(1) (Back light control) to
1
(Address 0xF1, Value 0x22) -> change GPO2_SEL=bits(0:3) from
MIPI_TE(0001b) to BC_CTRL (0010b)
BRANCH=scarlet
BUG=b:73133861
TEST=KD display with and without HW fix on Scarlet
Change-Id: Ia076a378b10417dd9891746f9bc1086360a0f6e6
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-on: https://review.coreboot.org/25023
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like there's a typo in the GPIO state table we print as part of
assembling the coreboot tables. Of course, high GPIOs are represented as
1 and low GPIOs as 0. Fix this display bug.
Change-Id: I59b4d49955c13f920576dd09f463e2d399ab64e0
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25022
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If the SoC is VT-d capable, write an ACPI DMAR table. The entry for the
GFXVTBAR is only generated if the IGD is enabled.
Change-Id: Ib354337d47b27d18c3b79b5de3b4fa100b59c8fc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Allows eMMC in PCI mode to be seen/used by Windows.
Test: boot Windows installer on google/edgar, observe internal
eMMC storage available for installation when eMMC in PCI (vs ACPI) mode.
Change-Id: I4272c198e5e675f451a1f4de5d46e3cd96371446
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch configures the gpios for all the gpio communites.
Change-Id: Ibc16edd96f4ef6d55f3a99b195bf4920929b1578
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Change-Id: Id45409a9561671237410dd2f8f0bbfe61ff33562
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Per vendor datasheet, corrected linkfreq of imx258 as
{633600000, 320000000}
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: Ie5beed44c15e26b9f82cb305a91b8ff90a9ea867
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-on: https://review.coreboot.org/24990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We want to report the board SKU via the SMBIOS tables. Add support for
this, obtaining the ID itself from the EC.
BUG=b:74175244
BRANCH=none
TEST=manually on grunt with another CL:
mosys platform sku
0
Change-Id: I9e08d64df3f89d3703de047dd9ec8e1717e6b212
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add WACOM EMR in devicetree I2C #2.
BUG=b:72062737
BRANCH=master
TEST=Verify EMR on nami
Change-Id: Icbe809a48959e5749262aeb1b89b09c4bdafbbc2
Signed-off-by: jasper lee <jasper_lee@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/24997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds SPD files for memory IDs 7 on nami.
BUG=b:73807138
Change-Id: I25fe3b347057eea75c58bfb88df41bdb28cc1460
Signed-off-by: jasper lee <jasper_lee@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:69011806
BRANCH=master
TEST=none
Change-Id: I2ea44b03336b901af68f9092f3386b42d8516b72
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/24962
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
File soc/amd/stoneyridge/sm.c has a CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
that's not used at all and has no control. It's also not used in the
build process. Remove the define from sm.c, create a true Kconfig
definition and use it to define if power should be restored after a power
failure/recovery.
BUG=b:72873003
TEST=Build kahlee. Use serial output to check what is being programmed
to RTC shadow. Build with and without selecting the Kconfig parameter.
Then remove serial output and leave the parameter unselected (always S5
at power recovery).
Change-Id: Iec82cb68cf1e2a820e610f12d8620488662232aa
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The LPEA device memory resources, required by Windows drivers,
were not being set. Allocate required resources per Inte'sl CHT
Tianocore reference code.
Test: boot Windows on google/edgar, observe LPEA device working properly.
Change-Id: Ic3ecfc2ddade7d76dbaa95ffdd82599c3bcf35da
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
As per the latest schematics, this change configures GPP_B0 as wake
source for WLAN.
BUG=NONE
BRANCH=master
TEST=emerge-nautilus coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I72b940452cfbbe471279ef117a868a8ae0b65b8b
Reviewed-on: https://review.coreboot.org/23526
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Certain platforms need paging enabled during cache-as-ram because
dirty lines are being evicted by a heavy speculative frontend. Paging
needs to be enabled in order to utilize the NX (no execute) bit for
the regions that are strictly data (such as the stack). This utility
creates 32-bit PAE page tables using a static address space, and
the resulting tables have entries for all the PDPTEs such that it makes
it easy to enable 2MiB naturally aligned DRAM mappings once memory is
trained. Either binary files can be generated or C files. The pages that
are linked use a default base address of 0xaa000000 that can be changed at
runtime to reflect where the page tables are actually loaded. Or
specify a physical address on the command line that is known a priori.
iomap.txt:
0xd0000000, 0x100000000, UC, NX # All of MMIO
0xff000000, 0x100000000, WP, # memory-mapped SPI
0xffff8000, 0x100000000, WP, # XIP bootblock
0xfef00000, 0xfefc0000, WB, NX # CAR
0xfef40000, 0xfefc0000, WB, # verstage
0xfef20000, 0xfefc0000, WB, # romstage
0xfef40000, 0xfefc0000, WB, # fsp-m
$ go run util/x86/x86_page_tables.go --iomap_file=iomap.txt
Merged address space:
00000000d0000000 -- 00000000fef00000 UC NX : 375 big 256 small
00000000fef00000 -- 00000000fef20000 WB NX : 0 big 32 small
00000000fef20000 -- 00000000fefc0000 WB : 0 big 160 small
00000000fefc0000 -- 00000000ff000000 UC NX : 0 big 64 small
00000000ff000000 -- 0000000100000000 WP : 8 big 0 small
Total Pages of page tables: 5
Pages linked using base address of 0xaa000000.
BUG=b:72728953
Change-Id: I47625a24979b196011e2293712a8cdbdbb880d79
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/24919
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is done by overriding the weak functions from smbios.c
Some values are hardcoded as they are characteristics of the
Tagada system. Other are retrieved from the BMC through the
bmcinfo interface.
Change-Id: I9b08660c6677864f5c96c66002b35bd05a366053
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23843
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add more information on baseboard as described in SMBIOS Reference
Specification 3.1.1.
Change-Id: I9fe1c4fe70c66f8a7fcc75b93672421ae808bf1b
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Idd93b64ef91a569127a0713fdb499dff2a1f11db
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0093cfafe7eaa4a4381e67c9b871fdf28abc470d
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This interface gives access to configuration information stored in flash
by the Tagada BMC before booting the SoC.
Change-Id: I4351aa11b08bdf65e14706b261c532bbf8837aed
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Alkali will use LPDDR3, so need to have Nami support both
DDR4 and LPDDR3. We do this with the PCH_MEM_CONFIG4 GPIO.
BUG=b:73514687
BRANCH=None
TEST=None
Change-Id: Ife6740ce0e8fe109ded7b954134171ba91895628
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add spd files for LPDDR3 based on info received from factory team.
BUG=b:73287172
BRANCH=None
TEST=None
Change-Id: I8924ce97ea422ef1e9a5becb5ea2fda3bf77d8cf
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
* Limit dependency on vendorcode header files and use defines from
iomap.h and southbridge.h
* Factor out to functions, device power-on code for AMBA and UART.
BUG=b:69220826
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt
Change-Id: Ibcf4d617e2a0a520a6d7e8d0d758d7a9705a84ea
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Change OSCOUT1_ClkOutputEnb programming to use registers from iomap.h
and southbridge.h
BUG=b:69220826
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt
Change-Id: Ib138dae6057394740c415e882e4dbd925882c2de
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
* Add definitions to iomap.h for AMD ACPI MMIO base addresses.
* Add FCH AOAC registers for enabling FCH devices.
* From: BIOS and Kernel Developer's Guide (BKDG) for AMD Family 15h,
Models 70h-7Fh Processors Rev 3.04
BUG=b:69220826
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt
Change-Id: I45c1d1d7edc864000282c7ca4e2b8f2a14ea9eac
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/24998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Change-Id: I12ae0d556c43d3d6537cac5d8f640e6a960101ae
Signed-off-by: Ben Pye <ben@curlybracket.co.uk>
Reviewed-on: https://review.coreboot.org/25017
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase memory allocated for the LPEA firmware from 1MiB to 2MiB
to match Intel CHT reference code and fix Windows functionality.
Test: boot Windows on google/edgar, observe no error in Device Manager
for LPEA audio device due to BAR2 resource allocation.
Change-Id: I7cffcdd83a66a922c2454488c8650df03c9f5097
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Without PMAX correctly set, the calculation for PLEN is incorrect,
leading to a Windows BSOD on boot. Correct PMAX using code from
Baytrail SoC, setting PMAX to (CONFIG_MMCONF_BASE_ADDRESS - 1).
Test: Boot Windows 10 on google/edgar without BSOD.
Change-Id: I4f2f4a0ff3a285826709f9eaafa40b0bf0cafb83
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24985
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5df7033e1e52c78e97cdbd26aef2d7824ea67f8b
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/12403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Alan(11")/BigDaddy(14") right type-A(port#2), CCD(port#4) are
occasionally undetectable. USB 2.0 phy needs an override to enhance
drive strength.
right type-A port#2
PERPORTPETXISET: 4
PERPORTTXISET: 4
IUSBTXEMPHASISEN: 1
PERPORTTXPEHALF: 0
CCD port#4
PERPORTPETXISET: 7
PERPORTTXISET: 7
IUSBTXEMPHASISEN: 1
PERPORTTXPEHALF: 0
BUG=b:72922816
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I2b18c11709280d00ec3a6ef10f93a416acb4fb45
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/24969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some type-c monitors do not immediately assert HPD. If we continue
to boot without HPD asserted, Depthcharge fails to show pictures
on a monitor even if HPD is asserted later.
Also, if an HDMI monitor is connected, no wait is needed. If only
an HDMI monitor is connected, currently the API always loops until
the stopwatch expires.
This patch will make the AP skip DisplayPort wait loop if it detects
an HDMI monitor. And if an HDMI monitor is not detected, the AP will
wait for DisplayPort mode (like before) but also its HPD signal.
This patch also extends the wait loop time-out to 3 seconds.
BUG=b:72387533
BRANCH=none
TEST=Verify firmware screen is displayed even when a type-c monitor
does not immediately assert HPD. Verify if HDMI monitor is connected,
AP does not wait (and firmware screen is displayed on HDMI monitor).
Change-Id: I0e1afdffbebf4caf35bbb792e7f4637fae89fa49
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/23816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The MMCONF base address and length are set in Kconfig so it does
not need to be redefined by the SOC as the code can just use the
Kconfig variable directly.
Tested on a fizz board to ensure MCFG is still created properly.
Change-Id: I5fd472b1afc8264823a2b9db0f296fbfb6b1ecc0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24975
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI MCFG table is generated with a static end bus number of 255,
which expects that the reserved range in E820 is 256MB. However the
actual MCFG range is configurable with Kconfig, so these two values
may not match when the OS tries to determine the range:
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) (size reduced!)
acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
Instead of forcing the end bus number to be 255 use the Kconfig value
to set it based on the current configuration.
Tested on a fizz device to ensure that the kernel no longer complains:
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
Change-Id: I999ea9b72b9deba5f27dd692faa0408427a0bf89
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24974
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO pins for UART 0 on Fizz are routed to the add-in card slot
and should not be used as a UART device. coreboot is setting the
pins to GPIO Mode but FSP is re-configuring them for Native Mode
and the behavior is unexpected when the kernel tries to initialize
the UART device.
The UART 0 device is PCI function 0 so it needs to be enabled for
other functions to be visible to the OS so it can't just be disabled.
Instead, set the device to PchSerialIoSkipInit so that FSP will not
change the pin state.
BUG=b:73006317
TEST=Tested with add-in card on fizz hardware to ensure the pin state
does not change when FSP runs or the kernel boots.
Change-Id: Id97c1e482ef0d5642fcf9018d802e1d0e073263d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The SMBus PCI device ID for Stoney wasn't updated when the code was
pulled over from hudson. This means that the IOAPIC wasn't being
initialized in coreboot.
BUG=b:74070580
TEST=Boot Grunt, see IOAPIC init messages in console.
Change-Id: Ida5d3f3592488694681300d79444c1e26fff6a1a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/24930
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 2e81f394cffc6f1993a5f004356ed35f6064fe48, as it will
have side effect that will make system shutdown failure. System will not
enter S5 sleep state, instead a global reset will be generated.
Once camera driver ACPI framework ready, isclk programing will be moved
into APCI method, in _PS3, isclk will be turned off to save power.
BUG=b.72532565
BRANH=master
TEST=Apply the changes and flash coreboot, on meowth devices, issue
"halt" in OS stage, system can shutdown successfully.
Change-Id: If35697911f97c524d9b52bdf4dae5c9ef1cc8618
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25006
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 1dfc2c3
[google/chromeec: Enable unified host event programming interface]
added support for UHEPI, but google_chromeec_is_uhepi_supported()
incorrectly treats negative error return codes from
google_chromeec_check_feature() as supported. Fix this check to only
treat positive return values as supported, as per the original intent.
Test: boot google/lulu, verify cbmem console reports UHEPI not
supported even if feature check returns error code, verify lid/kb
wake events correctly wakes the device from S3/sleep.
Change-Id: I7846efb340bc1546b074e8502daf906c444bd146
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/24982
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for variants to use secondary SPD if
required. This enables a variant to have different types of memory
supported using the same image.
BUG=b:73514687
Change-Id: I3add65ead99c510f2d6ec899fbf2cb9a06c79b0c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Similar to Soraka, this change sets the pch_trip_temp value to
75C. This is important so that PMC can shutdown the thermal sensor
when CPU is in C-state and DTS temp <= pch_trip_temp.
BUG=b:74089135
Change-Id: Ic46fa0681796b821dfb014ab91734c960df7846a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently, the AP check-in time-out in bsp_do_flight_plan is set to
100ms. However, as the number of APs increases, contention could
increase especially for resource like UART. This led to MP record
time-out issues on KBL platform with 7 APs and serial-console enabled
BIOS image.
This change increases the time-out value to 1 second to be on the safer
side and let APs check-in before continuing boot.
BUG=b:74085891
TEST=Verified that MP record time-out is not observed anymore on Nami.
Change-Id: I979c11a10e6888aef0f71b5632ea803a67bbb0ff
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a configurable delay in milliseconds before SLP_EN is set in
SLP_SMI for S5. Reason for doing this is to avoid race between SLP and power
button SMIs.
On some platforms (Nami, Nautilus), it was observed that power button SMI
triggered by EC was competing with the SLP SMI triggered by keyboard
driver. Keyboard driver indicated power button press which resulted in
depthcharge triggering SLP_SMI, causing the AP to enter S5. However, the power
button press also causes the EC to send a pulse on PWRBTN# line, which is
debounced for 16ms before an interrupt is triggered. This interrupt was
generated after SLP_SMI is processed which resulted in the device waking back up
from S5.
This change adds a config option SOC_INTEL_COMMON_BLOCK_SMM_S5_DELAY_MS which is
used to add a delay before SLP_EN is set for S5. This change should only affect
CHROMEOS boards as the config option will be 0 in other cases.
BUG=b:74083107
TEST=Verified that nami, nautilus do not wake back from S5 on power button press
at dev mode screen.
Change-Id: Iaee19b5aba0aad7eb34bd126fda5b0f6ef394ed7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:74083107
Change-Id: I98ab5c84268e8754fbaf6a30cd26fe1084e45a20
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/24963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is useful information, when debugging problems related to graphics.
Change-Id: Iacb0ae5f012207192379fd07e91f4687ec32cdfb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/23807
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit d2d2aef6a3 (sb/intel/{bd82x6,ibexpeak}: Move RCBA macros to a
common location) makes some platforms use the wrong OIC register defi-
nition. It was extended to 16-bit in the corporate version of ICH10.
So let's give the new size and location a new name: EOIC (extended OIC).
This only touches the systems affected by the mentioned change. Other
platforms still need to be adapted before they can use the common RCBA
definitions.
Change-Id: If9e554c072f01412164dc35e0b09272142e3796f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/24924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The console subsystem allows printk() to be called prior to the
drivers and/or infrastructure is completely set up. In those
situations don't allow messages to be added until the console
is completely initialized.
BUG=b:73898539
Change-Id: Idc3840132d7f95f8e22045d7484c528d828bb0de
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/24917
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on pcie ports 9,10. Enable Root Port 9 and set up clkreq 3.
BUG=b:72120814
TEST: Boot to OS via NVMe
Change-Id: I272b63b11e6b00ae5bdbef5a37ee517cc0636f6d
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/23208
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
2760p: enable PCIe
8470p: enable mSATA
8460p: enable PCIe, also add comments according to circuit diagram
2570p: comment for some USB ports
Change-Id: Ib5209f2dfb249fca5bae89bc6da3b704c8e903dd
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/23357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When clearing events from the EC, an error is returned when we try
to clear an event that doesn't exist. This is normal, but can
be distracting when trying to track down an error, so add a message
saying that the error is expected.
BUG=None
Test=Build Grunt with SMM debug enabled. See message before
"EC returned error result code 1".
Change-Id: Ib2e684e357e821c795de4b59658432c91a8d63fc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/24914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:73817825,b:69011806
BRANCH=master
TEST=Build and flash to meowth, verify cpufreq shows up in kernel
for all cores :
localhost ~ # find / -name "cpufreq"
/sys/devices/system/cpu/cpu3/cpufreq
/sys/devices/system/cpu/cpu1/cpufreq
/sys/devices/system/cpu/cpufreq
/sys/devices/system/cpu/cpu2/cpufreq
/sys/devices/system/cpu/cpu0/cpufreq
/sys/module/cpufreq
/usr/share/laptop-mode-tools/modules/cpufreq
Change-Id: I63242b2b049e37167c0d3b8eab630cb6e15a75fd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/24902
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sometimes the USB device is not detected. USB2 port#1 and #4 PHY register need
to be overridden.
port#1:
PERPORTPETXISET = 4
PERPORTTXISET = 4
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
port#4:
PERPORTPETXISET = 7
PERPORTTXISET = 7
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
BUG=b:72623892
BRANCH=master
TEST=emerge-sand coreboot chromeos-bootimage
Change-Id: I4051aefbec4583bb1f8babec08fdbeb27f749769
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/23879
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If the SoC is VT-d capable, write an ACPI DMAR table. The entry for the
GFXVTBAR is only generated if the IGD is enabled.
Change-Id: Id7c899954f1bae9d2b48532ca5ee271944f0c5f6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX
IOMMU and the general IOMMU respectively. These addresses have to be
configured in MCHBAR registers and reserved from the OS.
Change-Id: I7afcce0da028a160174db2cf6b4b6735bcd59165
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Intel DCI (direct connect interface) allows debug Intel target using
USB3.0 ports. It will support debug via USB stack (DCI Dbc) using USB3.0
only.
BUG=None
TEST=Turn on DCI trace hub in descriptor.bin and flash the coreboot
image. Using DAL to halt/run CPU.
Change-Id: I39e68dabfcb9e659733019334299e562eee3681d
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
If switch to VT2 on nautilus, screen flicker appears. We found if we
rollback the change of slew rate setting, then the flicker issue will
be gone: https://review.coreboot.org/c/coreboot/+/22588
But nautilus board needs slew rate tuning to reduce EE noise, so we
decided to change only SlowSlewRateForSa to 2 (Fast/8) instead of
rollback the whole change of the CL:22588. It can remove the flicker on
VT2.
BUG=b:71397040
BRANCH=master
TEST=emerge-nautilus coreboot
Change-Id: Id1d4bd8b1316c02c783de708ec4658e030193a26
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/23877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Sometimes the USB device is not detected. USB2 port#1 and #4 PHY register need
to be overridden.
port#1:
PERPORTPETXISET = 4
PERPORTTXISET = 4
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
port#4:
PERPORTPETXISET = 7
PERPORTTXISET = 7
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
BUG=b:72623892
BRANCH=master
TEST=emerge-reef coreboot chromeos-bootimage
Change-Id: Iab782ac6dfd81af839fff0e60e2b2460ce722733
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/23878
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to there are some chances USB devices can not be detected.
USB2 port#1 and #4 PHY register need to be overridden for variants
Santa/Lava/Blue/Bruce/Astronaut.
port#1:
PERPORTPETXISET = 4
PERPORTTXISET = 4
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
port#4:
PERPORTPETXISET = 7
PERPORTTXISET = 7
IUSBTXEMPHASISEN= 1
PERPORTTXPEHALF= 0
BUG=b:72623892
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: I401905685cc3078df657919b162272c3de320296
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/23881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The GPIOs for PCIe reset and power enable for WLAN must be set up before
amdinitearly for wlan to function.
BUG=b:73898539
TEST=Boot, see WLAN controller in lspci
Change-Id: I568a3240a54817ab6dcf15fe39f7f1336943852b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/24916
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The printk() calls in sb_program_gpios() aren't necessary, and incur a
13 second delay if the function is called from
bootblock_mainboard_early_init(). This commit removes them so GPIOs can
be set up earlier.
TEST=call sb_program_gpios from bootblock_mainboard_early_init
BUG=b:73898539
Change-Id: I064291decf47d86132e36469e029b3262ec20172
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/24915
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7acffcf3fc36742c77ce00b253f5b0a68d435798
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/24911
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This allows for a mainboard to change the value from its Kconfig.
The default value is still SMBIOS_ENCLOSURE_DESKTOP (0x03) or
SMBIOS_ENCLOSURE_LAPTOP (0x09) if SYSTEM_TYPE_LAPTOP is set.
Change-Id: I35bc913af69565531831746040a0afe0cabe1c58
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch fixes brokenness issues in coreboot with CONFIG_DISPLAY_HOBs
config selection due to recent UDK2017 package changes.
TEST=Build and boot UDK2017 platforms with DISPLAY_HOBS select.
Change-Id: I5c779c86870c62253d64c6af456bf017553e269c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- consolidate commonality in meowth and zoombini's SPD makefiles into
a common zoombini/spd/Makefile.inc
- move all SPD hex files into zoombini/spd directory
- move SPD_SOURCES definitions to variants/$(VARIANT_DIR)/Makefile.inc
BUG=b:69011806,b:71776625
BRANCH=master
TEST=Verify 'emerge-meowth coreboot' and 'emerge-zoombini coreboot'
compile and boot successfully.
Change-Id: I2291ebaf0ef5da1b22eb0e8fa7af8dbb50848c29
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23874
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In PORTSC, Port Enabled/Disabled(PED) is RW1CS.
When there is a USB device attached on system, current UPWE method
will set 1 to PED, this will cause port disabled as it's RW1CS.
This change is inspired by xhci_port_state_to_neutral in linux driver.
It will mask all RO and RWS bits and set WDE and WCE.
BUG=b:70777816
TEST=System won't be awakend from s3 automatically when usb devices
is attached. Also system can be awakend by hotplugging usb
devices under S3.
Change-Id: Ifd4c2d6640fea538e0ac71d7c5e73ab529e94f42
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:72062694
BRANCH=master
TEST=Verify touchscreen on nami works with this change.
Change-Id: Iaec71a11121b3d2849f12d18cda0e506be2ace09
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/23872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add LPDDR4 initialization support.
BUG=b:73136980
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ieffcfa2f9d075eb0be13562f1a0c7ee503b005d9
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a boot state callback to print ME version after
DEV_ENABLE is complete. Information is printed only if UART_DEBUG is
enabled because talking to ME to get the firmware version adds ~1
second to boot time.
TEST=Verified on Soraka that ME version printed is correct.
Change-Id: I360d5d7420950d5aa255df08be6d7123621b87a8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Many generations of Intel hardware have identical code concerning the
RCBA.
Change-Id: I33ec6801b115c0d64de1d2a0dc5d439186f3580a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The resource allocator was overly complicated due to porting
from a multi-node resource allocator. It had some assumptions
about the UMA memory and where it would be located. The
refactored allocations account for UMA being reserved above 4GiB.
TEST=Check CBMEM table has correct RAM regions.
Change-Id: I722ded9fb877ec756c3af11fcb5fea587ac0ba8e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Save the UMA base and size settings returned by AGESA
in amdinitpost();
Change-Id: Id96cc65582118ad41d397b1a600cab1615676a55
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:70731385
BRANCH=master
TEST='emerge-meowth coreboot chromeos-bootimage', flash
image.serial.bin to meowth board, boot into kernel, and
verify 4 cores are running.
Change-Id: Ia233e41acd19b317f82433a5d41d84ea934a66c4
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23839
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some DIMMs have invalid strings when it comes to device part number
(bytes 0x149-0x15c). From DDR4 SPD specs it should be ASCIIZ with unused
space filled with white spaces (ASCII 0x20). Byte 20 should be 0 (ASCIIZ),
all others should be ASCII.
Create a test that detects invalid strings and replace invalid
characters with *. If a replacement was made the output string then must
be <Invalid (replaced string)>.
BUG=b:73122207
TEST=Build, boot and record serial output for kahlee while injecting
different strings to dmi17->PartNumber. Use code to examine SMBIOS,
while testing different valid and invalid strings.
Remove string injection before committing.
Change-Id: Iead2a4cb14ff28d263d7214111b637e62ebd2921
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Kahlee DIMM have invalid string when it comes to part number
(bytes 0x149-0x15c). We currently force a NA string, but grunt has the
proper strings. Just let the string go through, and a second commit
within smbios.c will be responsible for testing the string and taking
proper action.
BUG=b:73122207
TEST=Build, boot and record serial output for kahlee while injecting
different strings to dmi17->PartNumber. Remove string injection before
committing.
Change-Id: I427262873f9ec80f459245e5f509e28a68de3074
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
* Add David, Jeff, and Shine
* Remove Fei
Change-Id: I2803af80ac8c2b1d04ecd125c0cb123e736cdf7e
Signed-off-by: Vanessa Eusebio <vanessa.f.eusebio@intel.com>
Reviewed-on: https://review.coreboot.org/23847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mariusz Szafranski
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This change removes extra newline characters from print statements for
wake masks.
Change-Id: I13cde76bfb0f10b1dda8117c27f2891e909f9669
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Coverity scan has found an error where a NULL pointer is dereferenced.
The bug would happen if the devicetree does not contain a valid entry
for PCA9538. In this case the code
* if (dev->path.i2c.device == PCA9538_SLAVE_ADR)
would dereference to a NULL pointer.
This patch fixes this issue. Thanks coverity!
Found-by: Coverity (CID 1386126: Null pointer dereferences (REVERSE_INULL))
Change-Id: I75e271d86c16fa3938420c43575ebba910f6a2fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/23808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Our CFM daughter card would like to use individual PCIe lanes for two
different devices on the card.
dlaurie@ has reconfigured PCIe port 9-12 from 1x4 to 1x2 + 2x1 on b2b
connector on fizz to meet the requirement:
https://chrome-internal-review.googlesource.com/571936
We also need to enable the ports on device tree.
BUG=b:72523836
TEST=none
BRANCH=fizz
Change-Id: Icded9850d833752680e0174b6c476e657817b319
Reviewed-on: https://chromium-review.googlesource.com/923867
Commit-Ready: Zhongze Hu <frankhu@google.com>
Tested-by: Zhongze Hu <frankhu@google.com>
Reviewed-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/924860
Commit-Queue: Shelley Chen <shchen@chromium.org>
Tested-by: Shelley Chen <shchen@chromium.org>
Signed-off-by: Zhongze Hu <frankhu@chromium.org>
Reviewed-on: https://review.coreboot.org/23845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
This change adds a config option to allow mainboard to override
the console loglevel. When the option is set, the platform has
to define the function get_console_loglevel returning a valid
loglevel value.
This allows a mainboard to sample a GPIO to switch the loglevel
value between different environments (qualification vs production)
without re-flashing.
Change-Id: Id6cc72b8fe5c4c50a6f83ce80e6440b078eec6e2
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
While programming interrupts, a message "perhaps this device was defined
wrong?" shows up twice. This is caused because some devices have
interrupt programmed for APIC mode, but not for non-APIC mode. Fix
mainboard_picr_data table by identifying devices programmed with value
0x1F while programmed differently on mainboard_intr_data table. Do so
only for devices that are used by kahlee or interrupt required by old OS.
BUG=b:70788755
TEST=Build and run kahlee, Verify that message disappears from serial
output.
Change-Id: Ic285036290519ed3ee617dffa616bd26c61575c5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This commit uses newly defined macros to make it easier to read which
iomux function pads are being configured to use.
TEST=Booted grunt, confirmed display backlight came on.
BUG=b:72875858
Change-Id: I24e5091fc7ef696f8e9c932ce04664e6cc3ccb90
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit defines a set of macros for defining GPIO configuration that
are easier to read than the raw iomux function values used today.
TEST=None
BUG=b:72875858
Change-Id: Ie100c8494c565afa28fa44d78ff73155fc8c7ea8
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23828
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to set the output enable here; this is already handled
by the native function. I'm making this correction in this change to
prevent the GPIO pin descriptions from getting confusing.
BUG=b:72875858
TEST=Booted, confirmed S5_MUX_CTRL high with and without this change.
Change-Id: I9e047be7169586c59892ef2bdab915683feeebda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Turn on PCH iSCLK for meowth platform.
BUG=None
TEST=Boot up into OS and check register programming with iotools, the
command is iotools mmio_read32 0xfdad8000, returned value is 0x03.
Change-Id: I1e44e3748c9b37c8f60adcc47a866d445d77cfaa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23368
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order for ddr2.h and ddr3.h to be included in the same file it
cannot have conflicting definitions, therefore rename a few things and
move some things to a common header.
Change-Id: I6056148872076048e055f1d20a60ac31afd7cde6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
