| Age | Commit message (Collapse) | Author |
|---|
|
This change updates devicetree and GPIO configurations to match the
schematics:
1. pcie_rp...[2] is the one being used for wifi, thus, clk_req and
deemphasis_enable for [2] need to be set instead of [0].
2. WLAN power enable, wifi disable and PERST# GPIOs need to be
configured correctly.
BUG=b:76180142
TEST=Verified that wlan0 scan works.
Change-Id: Ic51a94902e2cac3491081ade32079e5b88719f45
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Thinkpad X200.
Change-Id: I9db7a71608aaec956a7b22649498b97d58f35265
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23418
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This moves the sandybridge both smm setup and smihandler code to a
common place.
Tested on Thinkpad X220, still boots, resume to and from S3 is fine
so smihandler is still working fine.
Change-Id: I28e2e6ad1e95a9e14462a456726a144ccdc63ec9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enables ThunderPeak WiFi card on M.2.
TEST=Verify wlan card shows up in lspci
Change-Id: I5b3f871bdc67bfc4ed283b997b2a5698451b2bd2
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/24931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable VMX if supported by CPU and enabled in board devicetree.
Check lock bit unset before enabling VMX.
Change-Id: Ic57eac45e9c65baa4479735c6d70a7eb685f080e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb.
Change-Id: I34e7d750d3f75757a68977ae8d92bfbee1a10af1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
Change-Id: I5aea15511c52d1191babf551feb237f4144683e4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When CONFIG_VBOOT is enabled then the xDCI controller should only be
enabled if the system is in developer mode. This prevents a system
in normal/verified mode from being used as a USB peripheral device
which could potentially be used to access user data.
This change adds a function to return whether xDCI can be enabled
or not, which will be used by the SOCs.
Change-Id: Ie3ee9dd7077c094a01fd857a2e4033a12ce8979b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use soc/common VMX block to enable VMX on supported devices.
Change-Id: Iaa1a6201b431783d709c0509715fa8e8b1ce349a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
This patch disables debug consent in the devicetree. When debug
consent is set to DBC by default, it prevents some clocks from turning
off during S0ix. This blocks S0ix entry.
This patch also enables S0ix from the devicetree.
BUG=b:76163091
TEST=enter S0ix and check if slp_s0 is asserted
Change-Id: I05001a41b13e7784c34fa8f1f773fb94bbdcd01f
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25312
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the NHLT configuration for the max98373 codec to skylake,
taken directly from cannonlake.
This will allow skylake/kabylake boards to use this codec.
Change-Id: Ifb6bf2d31fda25b18d9b1ce2bb721255335d55e4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
|
|
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I1738a2544eb2435cb4b8718bcce5170d1ef04f72
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/25144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This change adds a call to heci_reset before attempting to read
ME firmware version. This is important to ensure that both ME and BIOS
are in sync.
BUG=b:76167737
BRANCH=poppy
TEST=Verfied that ME firmware version read does not fail on first boot
after power failure (i.e. removing battery and AC power).
Change-Id: Ib6b39c398d2e1177b087352a4acb8bcf5a9897d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Current emmc tuning parameters for octopus were copied over from other
boards and result in failure to boot from emmc. This change gets rid
of the emmc tuning parameters in devicetree. Once emmc tuning tests
are run for octopus, these parameters can be added back.
BUG=b:75986903
BRANCH=None
TEST=Verified that octopus boots from eMMC without any errors in
depthcharge.
Change-Id: I7ac44a54afd1ecfe355a9654ac8e92133b67637f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch changes the GBB flag configuration to the latest usage in
upstream vboot (as of https://chromium-review.googlesource.com/976660).
Change-Id: I585d662d7de34b4964d028e3d06b4df5665fbe9e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The EC needs to set the PPCM value depending on whether
Turbo is enabled or not, and the values differ between
Broadwell (0, 1) and Skylake (1, 2) platforms.
Change-Id: I662dce54415e685c054ffc00b6afde0f1f7765e2
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The LPC I/O ports for EC communication were not set properly,
causing ectool to fail to read the Index I/O from the EC.
The EC Index I/O is on port 0x380 and the LPC I/O port needs to be
decoded by the PCI device for it to be accessible.
Correct the value for the Librem 13v1, 13v2 and 15v3.
Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change remove work-around code for the power issue of MIPI and
USB cameras on previous board revision. With the work-around code,
PMOF ACPI method cannot turn off MIPI camera. So we need to remove
it.
BUG=b:74214248
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/25337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The code is based on autoport and that for revolve_810g1
Tested:
- CPU i5-3437U
- Slotted DIMM 8GiB
- Onboard USB2 interfaces (wlan slot, wwan slot, camera, smart card)
- Mini pci-e on wlan slot
- On board SDHCI connected to pci-e
- USB3 ports
- USB3 hub on dock (connected to USB3 port 1)
- NVRAM options for North and South bridges
- S3
- TPM1 on LPC
- Linux 4.13.17-1 within Debian GNU/Linux testing, loaded from
SeaBIOS, or Linux payload (Heads)
Not tested:
- Fingerprint reader on USB2
Not working well:
- EHCI debug on port SSP2,(The USB port on the left, wired to ehci
before OS) it has always-on enabled by default (maybe via EC),
which disturbs FT232H's own power up, requiring a very critical
timing to plug it in for it to work.
Change-Id: I52e549ec18e8aa661a506a16dbc7f83417c0da78
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/25218
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=build
Change-Id: I32d185741ce20a3a82e6895de3026ade52d0bcc8
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
TEST=build
Change-Id: Ie54e310a94f61b8d86c13261937015e3f5a2ab01
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
A change introduced by commit fe4983e5 [1] in order to prevent
re-initialization of the TPM if already set up in verstage
had the wrong logic in the if statement, causing the TPM
to never be initialized if vboot is disabled.
The RESUME_PATH_SAME_AS_BOOT config is enabled by default for
ARCH_X86, resulting in the if statement to always evaluate to
false. Remove that condition from the if statement to allow it
to function as intended.
This patch also enables TPM initialization for FSP 2.0 with
the same conditions.
[1] intel/fsp1_1: Do not re-init TPM in romstage if already setup in verstage
https://review.coreboot.org/#/c/coreboot/+/14106/
Change-Id: Ic43d1aa31a296386c7eab6d997f9b701e9ea0fe5
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23680
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the support for KBL-S MCH and Z270, H270, B250 and
Q250 PCH chips.
BUG=None
BRANCH=None
TEST=Boot with KBL-S CPU and B250/H270 PCHs.
Change-Id: If03abb215f225d648505e05274e2f08ff02cebdc
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/25305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
In an attempt at consolidation, commit 0a203d1 [1] introduced
an additional read/write of the MISC_ENABLE msr, as well a bug
which nullified the setting of Intel SpeedStep by inserting said
read/write calls in between another set of read/write calls to the
same msr. Fix by reverting to previous (simpler) implementation.
[1] soc/intel/skylake: Use CPU common library code
https://review.coreboot.org/19566
Test: boot Linux on Librem13v2, read MISC_ENABLE msr and verify
SpeedStep bit correctly set based on devicetree setting.
Change-Id: Id2ac660bf8ea56d45e8c3f631a586b74106a6cc9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch sets the PNP config value to PNP_PERF_POWER.
The config values for soc can be found in chip.h
TEST = Build for octopus.
Change-Id: I2239aa70cb708e6e1c06339ca9d517e7eaa198ed
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25310
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Don't write more bytes than the caller requests.
Based on I484b5c1e3809781033d146609a35a9e5e666c8ed.
Change-Id: I336de417c7cd6f35cf84947fc4ae161c15bd93ef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch sets the PNP config value to PNP_PERF_POWER.
The config values for soc can be found in chip.h
TEST = Built and booted glkrvp, verified warm and cold
reboot and suspend resume.
Change-Id: Ia390c0fafe2de64bd9e4ca44e5ed5d904663ae3c
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds a new Kconfig option for mainboard octopus "HAS_TPM"
that auto-selects all TPM related options only if VBOOT_MOCK_SECDATA
is not selected.
BUG=b:76203913
TEST=Compiles fine with mocktpm.
Change-Id: Ib28fc47a70be58cd9a9ec65ce3b1cda68d558437
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25340
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Example output:
AGESA TYPE 17 DMI INFO:
Handle: 1
TotalWidth: 64
DataWidth: 64
MemorySize: 8192
DeviceSet: 0
Speed: 1200
ManufacturerIdCode: 44416
Attributes: 1
ExtSize: 0
ConfigSpeed: 933
MemoryType: 0x1a
FormFactor: 0xd
DeviceLocator: DIMM 0
BankLocator: CHANNEL A
SerialNumber(8): 00000000
PartNumber(20): HMAA51S6AMR6N-UH
CBMEM_ID_MEMINFO:
dimm_size: 0
ddr_type: 0x1a
ddr_frequency: 1200
rank_per_dimm: 1
channel_num: 0
dimm_num: 0
bank_locator: 0
mod_id: 44416
mod_type: 0x1a
bus_width: 64
serial(4): 0000
module_part_number(23): HMAA51S6AMR6N-UH ��@
dimm_size, mod_type, bus_width need to be updated so they return the
correct values. module_part_number is missing a null terminator due to
the AGESA part number being larger than the dimm_info buffer.
Example dmidecode output:
Memory Device
Array Handle: 0x0000
Error Information Handle: Not Provided
Total Width: 8 bits
Data Width: 8 bits
Size: No Module Installed
Form Factor: Unknown
Set: None
Locator: Channel-0-DIMM-0
Bank Locator: BANK 0
Type: DDR4
Type Detail: Synchronous
Speed: 1200 MT/s
Manufacturer: Hynix/Hyundai
Serial Number: 0000
Asset Tag: Not Specified
Part Number: HMAA51S6AMR6N-UH
Rank: 1
Configured Clock Speed: 1200 MT/s
Minimum Voltage: Unknown
Maximum Voltage: Unknown
Configured Voltage: Unknown
To enable the output set CONFIG_DEBUG_RAM_SETUP.
The Kconfig change is required in order to enable
CONFIG_DEBUG_RAM_SETUP, otherwise it's not a valid option.
BUG=b:65403853
TEST=Test output shown above
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5eac00b9400056357915761287770a400b3f9f8b
Reviewed-on: https://review.coreboot.org/25303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
dmidecode used to print
'HMAA51S6AMR6N-UH '
it now prints
'HMAA51S6AMR6N-UH'
BUG=b:65403853
TEST=Verified using dmidecode
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia10ef434a2377e34ae7a8f733c6465c2f8ee8dfa
Reviewed-on: https://review.coreboot.org/25302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Reference the JEDEC SPD spec and clarify some comments.
BRANCH=dimm-info
BUG=b:65403853
TEST=Documentation change only
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1f2a3a70919c34f17472904323ec5accdfc876be
Reviewed-on: https://review.coreboot.org/25301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables S0ix from the devicetree.
Change-Id: I38662dc7203366bdee5f1c7aaa18979867a79ba1
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25293
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the ACPI FADT flag ACPI_FADT_LOW_POWER_S0
if S0ix is enabled for the platform. This also sets the
FSPUPD to indicate the status of S0ix on the platform.
TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0 flag
is set in FACP table - FADT.Flags[21] bit.
Change-Id: I6214ebb61f25ef8b704e60c8474808493c92e6f6
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25292
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Always report that EC is in RO mode. This is a temporary workaround
for a hardware issue that is causing EC to appear to be in RW mode
when it is not. This change will be reverted once transition is made
to newer hardware.
BUG=b:74215817
BRANCH=master
TEST=Verify meowth can boot to recovery's insert screen.
Change-Id: Ib3705bba0bb1f351da79e599566fbffab94428f3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the config for setting SPD DIMM size to 512 bytes
for KBLRVP8 with DDR4 memory. Configure the DIMM1 memory
SPD data for channel0 and channel1. Set the UserBd UPD to
BOARD_TYPE_DESKTOP for kblrvp8.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I985968d331991884050c3920ec9798cd4cb371c7
Reviewed-on: https://review.coreboot.org/25194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
The VA space needs to be extended to support 48bit, as on Cavium SoCs
the MMIO starts at 1 << 47.
The following changes were done to coreboot and libpayload:
* Use page table lvl 0
* Increase VA bits to 48
* Enable 256TB in MMU controller
* Add additional asserts
Tested on Cavium SoC and two ARM64 Chromebooks.
Change-Id: I89e6a4809b6b725c3945bad7fce82b0dfee7c262
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/24970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:76058338
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I1858c7843d16b6b63fc30762a889916bbb9b781a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25311
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update FSP header files to match GLK FSP Reference Code Release v2.0.0
Change-Id: I93d95e1977a4e31981e8b91882059611d91f78a5
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/25247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SeaBIOS 1.11.1 was released with the changes below.
```
$ git log --oneline rel-1.11.0..rel-1.11.1
0551a4b paravirt: Only enable sercon in NOGRAPHIC mode if no other console
specified
a7aa43e pci: fix 'io hints' capability for RedHat PCI bridges
0e739f2 shadow: Don't invoke a shutdown on reboot unless in a reboot loop
5d9a515 build: Use git describe --always
```
Change-Id: Ia77e98edcd42b28677de9670ce13c2ea5d327315
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/25284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
BUG=b:72120814
BRANCH=master
TEST=none
Change-Id: I64ab38dda78345c1f3d7d3f2bf3cb04c19290ceb
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:73292699
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ic73ad38ad9a12bec614e530f7f35619246b9f57f
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25288
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print the wake status bits to the console. The format is kept similar
to Intel's to maintain compatilibity with inspection utilities. Add
relevant wake events from the register to the ELOG. Clear the register
before continuing.
TEST=Inspect console and ELOG for Grunt
BUG=b:75020968
Change-Id: Idc9d12326abb290e4f7a5c60677eb6e057d475b2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Update Cannonlake FSP header to version 7.x.2A.20, the following changes
were made:
1. Add MemtestonWarmBoot option.
2. Add enable8254clockgatingonS3 option.
3. Default disable Tccoffsetlock
BUG=None
TEST=None
Change-Id: Ie794960f0253b2a6dbd55ffda973756d15e35c01
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This change defines IFD_CHIPSET as sklkbl to allow ifdtool to set the
right access control bits for SKL/KBL platforms.
BUG=b:76098647
BRANCH=poppy
TEST=Verified that the access control bits on KBL platforms are set correctly.
Change-Id: I7b2131caa06d6a975e703262931ec0ea519a86aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The default values used by ifdtool for setting region access control
do not match the expected values for SKL/KBL as per the SPI
programming guide. This change adds platform "sklkbl" that sets region
access control bits differently for SKL/KBL images.
BUG=b:76098647
BRANCH=poppy
TEST=Verified that the access control bits on KBL images is set
correctly.
Change-Id: I1328d8006c25be282b3223268d8f1fd0a64e2ed3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I5eac0ae55e759ac9eb26783c11057db15fa62574
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/25254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
I2C bus 2 goes to the custom add-in card slot and it was disalbed cuase
it was idle.
Google CFM add-in card is going to use this I2C bus so it needs to be
re-enabled.
BUG=b:73006317
TEST=Tested with add-in card on fizz hardware and verified I2C bus 2 is
working properly.
Change-Id: I2c9b5a9323fd51872e340c35005c4a3432716808
Signed-off-by: Zhongze Hu <frankhu@chromium.org>
Reviewed-on: https://review.coreboot.org/25258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update the size in WP_RO segment of the flash to accommodate builds using
debug FSP.
Change-Id: I8b24422e1eef2d0a81006286d4fc58f238fdce11
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/25255
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the size in WP_RO segment of the flash to accommodate builds using
debug FSP.
Change-Id: I0a0d1d0121b503ff390adf3ce25973d72e59fdeb
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/25253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This creates a bip variant for octopus. Nothing is set in the variant
files here-- everything is picked up from baseboard.
BUG=b:75976864
TEST=None
Change-Id: I7a8ac3d8bb71416f05ef1a605684d92d5902abda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25285
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:73078053
TEST=build & boot Grunt
Change-Id: I2d4ba197b19c4948b867a61575e858b2a826a286
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Tools/scripts, like mosys/arc-setup, use int (4 bytes) to
read the sku id. In order to support "-1", we need to use
uint32_t (4 bytes) instead of using uint16_t (2 bytes) data type.
Otherwise, tools/scripts will read 65535 instead of -1.
Another reason to change this is that sku_id can be
supported by ec up to 4 bytes.
BUG=b:73792190
TEST=mosys output "Platform not supported" for -1 sku id
arc-setup read -1 sku id
Change-Id: Ib3baa8419f138abeb412ac09c2e7dc608e3b758b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:73133848
BRANCH=None
TEST=Build coreboot for Octopus board. Tested the GSPI interface
with a SPI EEPROM and got correct response to a RDID command
Change-Id: Ia10ab9da0055b54a96134a6e4c51b2a229a6fecf
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/24907
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove extra tab before printk statement.
Change-Id: Id82239f74ac030f25000a08764637f6d1b52b87b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/25295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change configures GPP_E22 to GPO_HIGH to enable CABC feature
on nautilus board.
BUG=b:68789889
BRANCH=poppy
TEST=emerge-nautilus coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ifed0d37bf8147aa1b580f594f36f186051c2eb52
Reviewed-on: https://review.coreboot.org/25120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Audio machine driver will enable/disable clock by making it as
a CCF clock in kernel.
BUG=b:74570989
TEST=cherry-picked https://patchwork.kernel.org/patch/10291875/
on 4.14 kernel
aplay -vv <file>
check register to see clock enabled
kill aplay
check register to see clock disabled
Change-Id: Ia553e55ffb358415067000d2d2d2744322d1c4db
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up the EC communication a little earlier so we can read the board
ID before programming GPIOS.
BUG=b:73078053
TEST=Build & Boot grunt, board_id() now gets ID correctly
Change-Id: Icf3f598824cfed69fa03ba2bb86503bb3c3699a5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25286
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:73133848
BRANCH=None
TEST=Build coreboot for Octopus board. Tested the GSPI interface
with a SPI EEPROM and got correct response to a RDID command
Change-Id: Iec96f926ba7162074090617b7cf1c84e36b0fb37
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/24906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The following PCI device ID can be included for jefferson peak wifi
devices driver support, and they are:
9df0 for jefferson peak on Cannonlake-LP w/CNVi
A370 for jefferson peak on Cannonlake-H w/CNVi
31dc for jefferson peak on Geminilake w/CNVi
BUG=None
TEST=None
Change-Id: I48886cea5578a302f6ef033cb35df4a38bd64ea8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to the schematic, Octopus boards have WLAN_PE_RST connected to
GPIO_164. This change configures that properly in devicetree.
BUG=None
TEST=None
Change-Id: I2ba4839e036f02c5e0316d08599894879133894a
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25248
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO pad configurations for GPIO68-71 are incorrectly configured as
outputs. This change corrects them to be inputs.
BUG=b:74932341
TEST=None
Change-Id: I319f8a64d83c29ed150316c15a8d429cc7c024f3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25217
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:74177699
BRANCH=poppy
TEST=Verify audio recorder function by different SKU ID
Change-Id: Ic6570703f6ab4a1b03cbba8370fc0f597ab6bcf2
Signed-off-by: amanda_hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
PCIe de-emphasis is enabled by default. Thunderpeak Wi-Fi requires
it to be disabled. Therefore allow it to be configured via a
device tree setting.
TEST=On GLKRVP, verify Thunderpeak Wi-Fi card shows up in lspci when
de-emphasis is disabled in device tree.
Change-Id: Iae204768dfe00a638c764644c44c7cda269e73e0
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25185
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO for EEPROM write-protect should be configured early, before
romstage. This change configures that pad earlier. This pad is the same
on the existing Octopus schematics.
BUG=None
TEST=None
Change-Id: Idf296ba6aad75b890afabd6f7c7c51fbaf911214
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We are enabling at the kernel level, but that is triggering an issue
where FSP expects it to be disabled so it forces a cold reboot on
every warm reboot, clearing the ramoops logs. Enabling in BIOS so it
matches what the kernel expects.
This is the same change that were done for eve:
https://review.coreboot.org/#/c/22449/
BUG=None
BRANCH=None
TEST=echo PANIC > /sys/kernel/debug/provoke-crash/DIRECT
check for /dev/pstore/console-ramoops
Change-Id: Icd0bd01f5aee4c89f503eebba0808a1f3059e739
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The GPIO programming of configure_stoneyridge_UART() can be done by the early
GPIO table, AOAC enabling was already removed. So configure_stoneyridge_uart()
became redundant. Remove procedure configure_stoneyridge_uart().
BUG=b:74258015
TEST=Build and boot kahlee, observing serial output does not changes from
previous serial output.
Change-Id: Ie67051d7b90fa294090f6bfc518c6c074d98cc98
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25192
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO_149 is used as ESPI clock feedback and configuring it as a GPO
results in EC communication failure. This change removes the
configuration of GPIO_149 as GPO in ramstage so that it remains
configured for ESPI (as it was when AP came out of reset).
BUG=b:75348718
Change-Id: Ie4f21b12fae027cdba54ce147e6d1a88ee854792
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Call sb_spibase() early so that it will set up the SPI base address.
This is another step to moving AGESA calls out of the bootblock.
BUG=b:74427893
BRANCH=master
TEST=Build and boot Grunt.
Change-Id: I665d32f3acb0046eb6abbd363735561f0372f2a0
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
glk has different memory profile values than apl. Therefore, a
translation is required to correctly set the proper profile value
depending on what SoC (and therefore FSP) is being used. Based on
SOC_INTEL_GLK Kconfig value use different profiles.
BUG=b:74932341
Change-Id: I6ea84d3339caf666aea5034ab8f0287bd1915e06
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25249
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It was required for all cores use the same CAR teardown function
(exit_car.S and gcccar.inc). AGESA has already been modified to do the
AP to do the call out. Create assembly code to call chipset_teardown_car
and then enter an endless loop with halt instruction. Then create the
call out that will call this new assembly code.
BUG=b:70338633
AGESA COMMIT=3313d277
TEST=Created a debug version of AGESA that would print the returned
status of HALT_THIS_AP. Build code without the fix, see the return.
Build code with the fix, see that there's no return.
Change-Id: I05ee405812211d93dfdbdc5ee7d9978c2eb585e1
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/24999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
AGESA.bin was updated in the binary repo, so update the submodule pointer.
Among other changes, this added a callback "AGESA_HALT_THIS_AP", which
requires updated header files.
BUG=b:70338633
TEST=build kahlee.
Change-Id: I5a07f1c539d00aed34cfe45d6d7ef60c1dc56566
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25183
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Devices that need to have their AOAC register enabled do have a delay before
they become available. Currently each device has their own wait loop. Create
a procedure that initializes all AOAC devices in a table and wait for all
AOAC to become alive, then call this new procedure before the call to
initialize the UART. Then change all procedures that initialize some AOAC by
moving the devices to the table and removing AOAC initialization code.
BUG=b:74416098
TEST=Build and boot kahlee checking that UART is sending debug messages out.
Change-Id: I359791c2a332629aa991f2f17a67e94726a21eb5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PcieRpHotPlug in apollolake UPD is default enabled. This change adds a
config option to enable hotplug only if explicitly requested by
mainboard. This changes the default behavior on all apollolake boards
to have hotplug disabled.
BUG=b:74633273
BRANCH=reef,coral
Change-Id: I572c054d31aaf5d43a79c4b1773ec9356da48d9d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change uses an array pcie_rp_clkreq_pin for accepting CLKREQ#
from mainboards instead of defining a separate property for each root
port. This allows us to use memcpy to copy the entire array into FSP
params as well as new properties for PCIe root ports can be added as
arrays in future CLs.
BUG=b:74633273
BRANCH=reef,coral
Change-Id: Ifa05f1e38fcfd95063ec327712e472cdbd12dbb7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1) Set the critical temperature threshold to 100C to match changes
on other boards. This is intended to reduce DPTF-initiated thermal
shutdowns before it has had a chance to react.
2) Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
BUG=b:67459049
BRANCH=eve
TEST=manual performance/power testing on Eve hardware
Change-Id: Ib660dcb25422fea0aa692fac5ba65b49808965ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
* Fix tlcl_read() for TPM 1.2
* https://github.com/nccgroup/TPMGenie
Change-Id: I1618b2cc579d189bccca7a781e2bed0976a8b471
Signed-off-by: zaolin <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/25184
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use gpio_keys driver to add ACPI node for pen eject event. Also
setting gpio wake pin for wake events.
BUG=b:73121017
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I5d87d938ac3a4e52e676850b9d8b80e83726275d
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Touchscreen power enable for Nami has moved from GBB_C22 to GPP_B4 in
the latest schematics.
BUG=b:74347464
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I3b1794d44f25c0d42d082d63b9e3ec3dfcef7528
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/25154
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Call function sb_acpi_mmio_decode() from bootblock_fch_early_init().
This enables decoding of the FCH ACPI MMIO regions 0xfed80000 -
0xfed81fff. This is another step to moving AGESA out of the bootblock
for StoneyRidge
BUG=b:74586747
BRANCH=master
TEST=Build and boot on Grunt.
Change-Id: I8cf329e5cd2002b225742fefa5c1ddd2598de674
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25161
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I18315e48653b16b34d1473e6c0bb2a2662a1a2c3
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/23870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to generate ACPI OpRegion, save the
table address in ASLB, and restore table address upon S3 resume.
Implementation largely based on existing Haswell/Lynxpoint code.
Test: boot Windows 10 on google/lulu with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: I024f4f0784df3cbbb9977692e9ef0ff9c3552725
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Octopus uses MAX98357A speaker amplifier and DA7219 codec.
Add device tree entries and Kconfig settings for these
components.
BUG=b:73292699,b:73230879
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I27b5113677a8bd44dbbae587e27616d9e0b90d7f
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25117
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7bb142d9f936b73e84d301028069d85cc15d596a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/25143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This change uses gpio_keys driver to add ACPI node for pen eject event.
BUG=b:74413116
TEST=Verified using evtest that pen eject event results in events as
expected.
Change-Id: I6019d633f4337137bb9fbba770040cb5b30da773
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/25147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The cannonlake FSP enables PchLockDownRtcMemoryLock by default, but we
need this memory to be writable. We normally over-ride this in the
SoC chip init code, so we'll do the same on cannonlake.
BUG=b:71722386
BRANCH=none
TEST=Filled /dev/nvram with 0xff and 0x00 bytes to verify we can flip
all the bits.
Change-Id: I7cdd4abc2b3795d7dd82236fbe3c112428ee882b
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
|
|
Fix the IRQ configuration: it must be level-sensitive not edge-sensitive
(and match the GPIO configuration).
BUG=b:71986991
BRANCH=none
TEST=on Meowth, /proc/interrupts shows 'IO-APIC 46-fasteoi chromeos-ec'
then run 'ectool --name=cros_fp fpmode fingerup' and see the number of
interrupts incrementing and the MKBP event happening.
Change-Id: Iba8cff21d637fe6bf4ef5152fc01aaf98906477d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/25110
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable System Agent dynamic frequency support by default.
BUG=None
TEST=Build and flash with debug version FSP, check SaGv in serial print
to be set to "4".
Change-Id: I7dd29db206b06e600407bb0b1d0bc7530f4ac93e
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25093
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SaGv(Sytem Agent Dynamic Frequency) have four settings, disabled,
disabled but running at fixed lower frequency, disabled but running at
fixed middle frquency, disabled but running at fixed high frequency and
totally enabled.
BUG=None.
Change-Id: Ib5fb648179e7889aaa64d91e6cf7a7a7503f4225
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/25116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Supported burst lengths are described at byte 16
Change-Id: I502710bdac7eec715b29febefd64be88e5a1b80a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
In preparation for moving AGESA calls out of the bootblock:
* Add sb_tpm_decode to enable FCH decoding of TPM 1.2 regions and Legacy
TPM IO 0x7f-0x7e and 0xef-0xee
* Modify sb_tpm_decode_spi to additionally call sb_tpm_decode.
BUG=b:65442212
BRANCH=master
TEST=abuild, build Gardenia, build and boot Grunt (with other changes
to call code not committed at this time)
Change-Id: I0e2399e113c765393209dd11fd835fc758cf3029
Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to generate ACPI OpRegion, save the
table address in ASLB, and restore table address upon S3 resume.
Implementation largely based on existing Broadwell code.
Test: boot Windows 10 on google/squawks with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: Iab15e1de2bb7d8fbec2e8705a621cfca0f255d4b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Most Intel platforms use separate registers for software-based
SMI (0xe0) and SCI (0xe8), but Atom-based platforms use a single
combined register (0xe0) for both. Adjust opregion implementation
to use the correct register for Atom-based platforms.
Test: Boot Windows on Atom-based ChromeOS device with Tianocore
payload and non-VBIOS graphics init; observe Intel display
driver loaded correctly and internal display not blank.
(requires additional change for Atom platforms to select
CONFIG_INTEL_GMA_SWSMISCI)
Change-Id: I636986226ff951dae637dca5bc3ad0e023d94243
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
ACPI ID for coreboot is now "BOOT" according to CL:18521.
BUG=none
BRANCH=master
TEST=none
Change-Id: I802ce284001b186f6cd8839b8c303d49f42b4d38
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/25042
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This creates a yorp variant for octopus; nothing too interesting now,
just picks up values from the baseboard.
BUG=b:74443669,b:74067452
TEST=Build
Change-Id: I55af8f02d33138a3b6bab7860a665e3deb5595c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables SAR configs when building with CHROMEOS option.
BUG=b:74439919
Change-Id: I11a8fa04a77f688ed288780f2c605b8ac701f5a9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since nami proto did not have any external pull on MEM_CONFIG_4, use a
weak internal pull down before reading it.
BUG=b:74420123
TEST=Verified that the value read for MEM_CONFIG_4 is correct on nami.
Change-Id: I45989d2ca35b863f391baba9e2f2e602033217d4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The current lpddr4 skus entries do not match the RAMID table in the
schematic. This commit updates that so they are consistent. Thankfully,
the values are the same as for glkrvp, so I just copied from there.
BUG=b:74392818
TEST=None
Change-Id: I2e63ea0b27ef58038e5a37949c31a808989c98c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
