| Age | Commit message (Collapse) | Author |
|---|
|
The `reset` gpio is currently being consumed by the btusb kernel driver.
The functionality was added in https://crrev.com/c/3342774. The goal of
the patch was to reset the BT device when command timeouts occur. This
works, but it doesn't support the case where the BT device is having
problems with USB enumeration. In that case the device can't enumerate
so the driver can't help resetting the device.
If we instead switch to using an ACPI power resource, the kernel can
control the BT device's power. This is beneficial when the device is
having USB communication problems since the kernel will try and power
cycle the device.
We don't lose the ability to reset the device on command timeouts
either since `btusb_qca_cmd_timeout` will enqueue a USB port reset if
there is no `reset` GPIO. So win / win.
This results in the following power resource:
PowerResource (PR02, 0x00, 0x0000)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x01)
}
Method (_ON, 0, Serialized) // _ON_: Power On
{
\_SB.CTXS (0x84)
Sleep (0x01F4)
}
Method (_OFF, 0, Serialized) // _OFF: Power Off
{
\_SB.STXS (0x84)
Sleep (0x0A)
}
}
I switched the device tree entry from using reset_gpio to enable_gpio
because the acpi_device_add_power_res method asserts the reset in the
_ON method unconditionally. This results in a small glitch on the line.
By using the enable_gpio we get the correct behavior.
I don't have a datasheet right now, so I just picked some values for the
reset timing. The kernel driver was using 200ms. We can revisit the
numbers when we get a datasheet.
BUG=b:218295688
TEST=Suspend stress test on nipperkin with 600+ cycles. Verify power
resource is created on the kernel. This should allow the kernel to
power cycle the device via usb_acpi_set_power_state.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib1eff86db76929f76432cd6f765880c892e7a786
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
When brya boards that use ChromeOS autoupdate update their firmware,
devices with SOC_INTEL_CSE_SUB_PART_UPDATE will end up attempting to
replace IOM and NPHY BPDT firmware in the CSE region. However, because
of the way the autoupdate works, the CSE RO will not be updated during
autoupdate. This means that these boards now have different stitching
schemes between CSE RO and RW and this causes the sub-partition update
to fail and the boot hangs. To remedy the situation for these boards,
a separate FMD files is provided so they can continue to use the
cse_serger tool for stitching. The only boards affected were kano and
brask, so they are updated here.
BUG=b:218376385
TEST=use flashrom to downgrade to 14474 then use futility to update to
image with this patch and system boots.
Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Change-Id: Ia8bdf6b28d952f6d983b84e39da96e159027a822
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This fixes building with -jx
Change-Id: I51efc03839c53b96fa248e6fe5dc0e00b773aa53
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
create SOC_INTEL_GFX_MEMBASE_OFFSET for platform to map graphic memory
base if required, because it may vary by platfrom.
BUG=b:216756721
TEST= Check default offset for existing platform and
update platform specific offset in Kconfig under SoC directory.
Change-Id: I6b1e34ada9b895dabcdc8116d2470e8831ed0a9e
Signed-off-by: Ethan Tsao <ethan.tsao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61389
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Brask cannot pass powerd_dbus_suspend test because the NIC does not
enter ASPM L1.2. Here we add "enable_aspm_l1_2" in devicetree for
RTL8125 to enable ASPM L1.2.
BUG=b:204309459
BRANCH=None
TEST=emerge and test with command powerd_dbus_suspend
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I9a56df1d68696f409f9ee681d37de6759a588d80
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add a new configuration parameter "enable_aspm_l1_2".
Write value 0xe059000f to register offset 0xb0 to allow kernel driver to
enable ASPM L1.2.
Use Kconfig "PCIEXP_ASPM" and "enable_aspm_l1_2" to decide whether to
enable ASPM L1.2.
BUG=b:204309459
TEST=emerge and test if the driver can read the correct value
Change-Id: I944dbf04d3ca19df4de224540bee538bff4d1f12
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add/update initial GPIO pin descriptions and initialization types for
chausie mainboard.
Change-Id: I14ea0e1086f626398a867896ee81ce07cf530182
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the APIC bus isn't used since a long time and the IOAPIC and LAPIC
talk to each other via the system bus, there is no longer the
requirement that the IOAPIC IDs mustn't overlap with the LAPIC IDs that
start at 0 and end at CONFIG_MAX_CPUS - 1. The current Intel code uses 2
as the IOAPIC ID while most of their CPUs have more than 2 logical cores
resulting in the IOAPIC having the same ID as one of the LAPICs.
All chipsets in soc/amd use the defines for FCH_IOAPIC_ID and
GNB_IOAPIC_ID for initializing the IOAPIC register, writing both MADT
and IVRS ACPI tables and there's no MPTable support for those SoCs that
might also rely on those IDs being consistent.
This patch changes the definitions for FCH_IOAPIC_ID and GNB_IOAPIC_ID
from CONFIG_MAX_CPUS and CONFIG_MAX_CPUS + 1 to 0 and 1. This also makes
sure that the IOAPIC IDs still fit in 4 bits despite Cezanne having a
CONFIG_MAX_CPUS of 16 resulting in the IOAPIC IDs being larger than 4
bits with the old code. While the Cezanne FCH IOAPIC supports 8 bits of
IOAPIC IDs, this is non-standard.
TEST=AMD Mandolin and Google Liara still work.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Id3a356480bb8407e0347cb5cef691fde7edc8deb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The following error message is now gone:
CC bootblock/arch/x86/id.o
/tmp/id-35b17a.s:35:7: error: expected relocatable expression
.long - ver
^
/tmp/id-35b17a.s:36:7: error: expected relocatable expression
.long - vendor
^
/tmp/id-35b17a.s:37:7: error: expected relocatable expression
.long - part
^
Tested with BUILD_TIMELESS=1 on x86_32 with gcc. The binary stays the
same.
Change-Id: I930e7b96c4428bcb95ff1903e6a3e7679171ffee
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch makes SKIP_CSE_RBP=y default for Apollo Lake if Boot Device is
memory mapped and ensures SkipCseRbp UPD is guarded against this config.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ifd01a25443e2582a90529e55be8d34a88342a103
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change adds LTE modem for beadrix.
BUG=b:204882915
BRANCH=dedede
TEST=Build and boot beadrix, check with command modem status
Change-Id: I7acb88634478ff486810b2c3fc14d6739c3268e1
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61328
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FCH_UART_ID_MAX == 2, and there are 2 UARTS, so we don't need the -1.
BUG=b:215599230
TEST=Build guybrush
Found-by: Coverity CID 1469611
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5f0171ed2d3da7f86ba3cfd0457f60d2d5722625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61869
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace `LEqual(a, b)` with `a == b`.
Change-Id: Iabfaaee22011a75cc981607d366d61660838ab21
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Agah port 0 does not have a retimer so the port needs
to be configured for the SOC to handle Aux orientation flipping.
Add the "TcssAuxOri" and "typec_aux_bias_pads" to lets the SoC IOM firmware control the Aux DC bias voltages.
BUG=b:210970640
BRANCH=NONE
TEST=emerge-draco coreboot chromeos-bootimage
Change-Id: I1fa5c4574b1a0e8dd2f66f3f6382436337c530fa
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Alder Lake N has single memory controller with 64-bit bus width. Alder
Lake common meminit block driver considers bus width to be 128-bit and
populates the meminit data accordingly. By setting half_populated to
true, only the bottom half is populated.
Ideally, half_populated is used in platforms with multiple channels to
enable only one half of the channel. Alder Lake N has single channel,
and it would require for new structures to be defined in meminit block
driver for LPx memory configurations. In order to avoid adding new
structures, set half_populated to true. This has the same effect as
having single channel with 64-bit width.
Change-Id: I414e5dc82caf47b6b96c474b3ef6e01c2ce0226e
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Change-Id: Iafe1a3476c0afa5ebfb75fb704429594e24e96f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The mainboards mc_apl{2,4,5,6} use VBOOT for verification and can be in
a recovery state for different reasons. In this case we still want the
MRC cache to be around to avoid the DRAM retraining on every boot.
This patch enables the Kconfig switch HAS_RECOVERY_MRC_CACHE which makes
the already available MRC recovery region in FMAP useable.
Test=Boot mc_apl2 in recovery mode and make sure the recovery MRC
cache is used.
Change-Id: I2ea4993f05dd87a0e637f55e84b4fc06f5e29ecc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
BUG=b:216096562
Change-Id: I4a5ee335ea8808b595dc65ebafd15baedfbdd06e
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This IRQ routing info is taken from mb/google/guybrush. The IRQ routing
on Chausie that was a 1:1 copy caused some issues with the I2C driver,
so port the Chausie IRQ mapping change back to Majolica.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb958639dd8aef7c60c050ad107dde7d1cd6a8bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This IRQ routing info is taken from mb/google/guybrush. This should fix
these errors:
[ 0.655051] i2c_designware AMDI0010:00: IRQ index 0 not found
[ 0.659239] i2c_designware AMDI0010:01: IRQ index 0 not found
[ 0.663198] i2c_designware AMDI0010:02: IRQ index 0 not found
[ 0.667200] i2c_designware AMDI0010:03: IRQ index 0 not found
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8c85c8e4b1c860d6ca25060353355f703a49e1e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
|
|
BUG=b:204401306
BRANCH=guybrush
TEST=emerge-guybrush coreboot
dump SSDT, see _HID instead of _ADR
Change-Id: I3f45fabac1548cca39379f91cc42fed0cd04f8a3
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Scan devices behind SoCs GPU controller to expose more buses.
BUG=b:204401306
BRANCH=guybrush
TEST=emerge-guybrush coreboot
Change-Id: Ib78e6570f101c71efaf9cc1843defcb05301cd30
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
For the generic board which uses Cezanne, we use the generic SPL
table. For the Guybrush Chromebook, we need to use a customized SPL
file.
BUG=b:216096562
Change-Id: I385b0fe13cb78a053c07127ec3ea1c61dc42c7e4
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Fix issue where registers always seem to contain their own offset.
After writing the desired register into SIRI, the requested data is
returned in SIRD. This register is 4 bytes after SIRI, commonly 0xA4.
Tested on TGL-H (SATA SIR registers are common), genuine data is
returned.
Change-Id: I322b11d53178e5b64e353c1b4e576548592c16c3
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Currently the SPM version string is stored at the end of the blob,
possibly without a trailing '\0'. Therefore, we should be careful not to
print characters beyond the blob size.
BUG=b:211944565
TEST=emerge-corsola coreboot
TEST=SPM version looked good in AP console
BRANCH=asurada,cherry
Change-Id: Icfeb686539dc20cf5b78de77c27bdbb137b5d624
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Several recovery images for newer ChromeOS boards fail in
extract_partition() due to parted detecting that there are overlapping
partitions, and therefore failing to print the partition layout
(this is potentially a parted bug; requries further investigation).
To work around this, fall back to using fdisk, making the assumption
that ROOT-A is always partition #3, and calculate the partition
start and size using the sector size.
Test: successfully extract coreboot firmware images from recovery
images which previously failed to extract (fizz, octopus, volteer).
Change-Id: I03234170ba0544af9eb0879253f0a8e0e7bf33f5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Wile historically there was a unique recovery image for each Chrome OS
board/HWID (with matching names), this is no longer the case. Now,
multiple boards share a single recovery image, so adjust how the proper
recovery image is determined, and how the coreboot image is extracted from it.
Test: successfully extract coreboot images for older 1:1 boards (e.g. CAVE)
and newer 1:N boards (e.g. DROBIT)
Change-Id: If478aa6eadea3acf3ee9d4c5fa266acd72c99b7a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds a new --loglevel option to the CBMEM utility which can
be used either numerically (e.g. `cbmem -1 --loglevel 6`) or by name
(e.g. `cbmem -c --loglevel INFO`) to restrict the lines that will be
printed from the CBMEM console log to a maximum loglevel. By default,
using this option means that lines without a loglevel (which usually
happens when payloads or other non-coreboot components add their own
logs to the CBMEM console) will not be printed. Prefixing a `+`
character to the option value (e.g. `--loglevel +6` or
`--loglevel +INFO`) can be used to change that behavior.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8458027083246df5637dffd3ebfeb4d0a78deadf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Config USE_PM_ACPI_TIMER to y for primus4es only as
commit 1ce0f3aab7 (mb/google/brya: Fix S0i3 regression)
breaks suspend stress test on ES CPU SKU.
BUG=b:211377699
TEST=USE="project_primus emerge-brya coreboot" and verified
the suspend stress test works on primus4es.
Change-Id: I8d19c10e2029e233542a8ceec272f8ede2b4bfac
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Few of the Alder Lake-N Device IDs according to EDS, are named as ADL_M
IDs in the current code. Hence rename those device IDs as ADL_M_N and
use them for Alder Lake-N platform.
Document Number: 619501, 645548
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I6042017c6189cbc3ca9dce0e50acfb68ea4003f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Refactor existing acp code into acp_gen1 variant as preparation for gen2
variant in sabrina.
Change-Id: Id9248584237196b5404b79d3a8552cb90fe4491e
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Check if FSP binary and coreboot FSP structures (fspmupd.h) match
sufficiently.
A change in minor number denotes less critical changes or additions
to the FSP API that still allow for the boot process to proceed.
A change of the AMD image revision major number will halt boot.
The Fspmupd.h header now defines IMAGE_REVISION_ macros for AMD
Picasso, Cezanne and Sabrina APUs.
BUG=b:184650244
TEST=build, boot and check fsp image revision info. Example:
FSP major = 1
FSP minor = 0
FSP revision = 5
FSP build = 0
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: I0fbf9413b0cf3e6093ee9c61ff692ff78ebefebc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
It's available in %r3 in bootblock and needs to be passed to payload in
%r27. We use one of two hypervisor's special registers as a buffer,
which aren't used for anything by the code.
Change-Id: I0911f4b534c6f8cacfa057a5bad7576fec711637
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
Change-Id: I309be370d66a808b355241fcee880883631f38ce
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
"hb-mode" is a -machine flag for QEMU. "hb" stands for Hostboot, which
is OpenPower firmware created by IBM.
QEMU for PPC64 can run initial program in two different modes:
* hb-mode=off with load address 0x00000000
* hb-mode=on with load address 0x08000000
Real hardware always loads firmware at 0x08000000 and coreboot shouldn't
require a special build to be run on QEMU.
Memory layout is updated to reflect change of load address.
Change-Id: I1bdc97a095bd46fccc862985b3bd24f4fa5bc054
Signed-off-by: Yaroslav Kurlaev <yaroslav.kurlaev@3mdeb.com>
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: Ie333294c7a311f6d47bdfbd1fc3cec0128cf63e7
Signed-off-by: Yaroslav Kurlaev <yaroslav.kurlaev@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Change-Id: I9895fc0dcc0ab72151f3b2bde409c8556525433d
Signed-off-by: Yaroslav Kurlaev <yaroslav.kurlaev@3mdeb.com>
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Add initial implementation for booting on QEMU POWER9 emulation.
Change-Id: I079c5b9ad564024dd13296ef75c263bdc40c9d39
Signed-off-by: Yaroslav Kurlaev <yaroslav.kurlaev@3mdeb.com>
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
This change adds mem_parts_uesd.txt that contains the new memory parts
used (H54G46CYRBX267,H54G56CYRBX247) by primus and Makefile.inc
generated by gen_part_id using mem_parts_used.txt.
BUG=b:218415732
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I0d236c51f0c996a22954046876f3494ba9e62693
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
makefile variables
Currently apu/amdfw_a-position and apu/amdfw_b-position currently depend on CEZANNE_FW_A_POSITION and CEZANNE_FW_B_POSITION. This causes error messages from awk as these variables are sourced from fmap_config.h and these variables are expanded before fmap_config.h is built. However these variables should not be set to CEZANNE_FW_*_POSITION. These files end up in the FW_MAIN_* fmap regions. These regions are placed at the proper locations through the chromeos.fmd file. The apu/amdfw_*-position variables are the positions within these regions where the files end up. These variables should be set to 0x40 to coincide with the beginning of the FW_MAIN_* regions, accounting for the size of struct cbfs_file + filename + metadata, aligned to 64 bytes. Currently they end up in the correct locations only because fmap_config.h does not exist when the apu/amdfw_*-position variables are expanded.
This change explicity sets the value of these variables to 0x40, removing the errors from awk and ensuring that these files end up in the correct location in the resulting image. These changes are also applied to the Picasso and Sabrina makefiles as well.
BUG=b:198322933
TEST=Verified that the apu/amdfw_* files end up in the correct locations as reported by cbfstool during the build, did timeless builds and confirmed that coreboot.rom images were identical, tested AP firmware on guybrush and zork devices
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: If1c2b61c5be0bcab52e19349dacbcc391e8aa909
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Introduce and use functions to translate eSPI IO/MMIO decode range IDs
into the corresponding register bits and the IO/MMIO range and size
register IDs into register offsets. This is a preparation to support the
additional eSPI decode ranges on Sabrina where not all enable bits and
base/size registers for one type of decode ranges are consecutive.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id91fe32447a06b049e33dfdacc8edfa2ebb2df39
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This aligns the register names more with the PPR.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4e7dc8dfc0fa5e86b9d4425f2496be86e039b686
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Nissa is using the FM101, which has the following power sequencing
requirements:
Power on: assert WWAN_EN, delay 20 ms, deassert WWAN_RST_L
Power off: assert WWAN_RST_L, delay 20 ms, deassert WWAN_EN
Add a power resource to the USB device, and use wwan_power.asl to
handle the power off sequence.
BUG=b:217092522
TEST=abuild -a -x -c max -p none -t google/brya -b nivviks
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ibe1b863a550c6af1ac3eb98f2aaa3db15b149ada
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Nissa is using the FM101 which is USB only. To allow us to reuse the
existing wwan_power.asl for power sequencing, move the PCIe-specific
part behind a new Kconfig HAVE_PCIE_WWAN.
BUG=b:217092522
TEST=Build brya0 and check that generated dsdt.asl doesn't change.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Icb6db91ce00deb2b30379f5ff7a974d1feb62ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If the LTE USB DB is not connected, disable the LTE-related GPIOs.
BUG=b:197479026
TEST=abuild -a -x -c max -p none -t google/brya -b nivviks
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I86251d8ad58d82ff2112ac5f2dfafdabbff4c76f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add an initial overridetree for nivviks based on the pre-proto schematic
and build matrix.
BUG=b:197479026
TEST=abuild -a -x -c max -p none -t google/brya -b nivviks
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Id3ecd184415a20a3a52da8bb5e60fe2ce0495b44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
There may be occasions where an I2C device was initialized during
"early initialization," but when used again in ENV_PAYLOAD_LOADER
before resource allocation happens, it would currently return that it
has not been assigned a BAR. However, because of the early BAR
assigned to it, it should still be valid to use that until proper
resources have been assigned, therefore return any BAR that may have
been assigned to the device during early initialization.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8ab599199592a72ae96cd9f95accfaa0d84e66b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The `chip` argument passed around to many functions in this driver is
actualy unused, so remove it where it is unused.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib8d32fdf340c8ef49fefd11da433e3b6ee561f29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change-Id: Ie20a2c35afc2b849396ddb023b99aab33836b8de
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The current SPI NOR speed mainpll_d7_d2 (78MHz) is too fast for MT8186's
HW design, which is capable of up to 52MHz. Therefore, lower the speed
to univpll_d3_d8 (52MHz).
BUG=b:218775654
TEST=emerge-corsola coreboot
TEST=Boot time didn't increase significantly
BRAHCH=none
Change-Id: I5a03e41d4ce47d45b97a805b9b98877ef0dac7b7
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
BSS is loaded as part of the bootblock, it is zeroed in the file so it
doesn't have to be cleared explicitly by the code.
Code for clearing is left as a comment along with a warning about alignment
requirements.
Vector operations are sometimes generated for code such as
'uint8_t x[32] = {0}', this results in an exception when vector registers
(VR) are not enabled. VSR (vector-scalar register) operations are also
enabled, there is no reason not to.
Change-Id: I878ef61619eb4a191805c8911d001312a0d717a0
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Fix regression after commit 9ec7227c9b
cpu/x86/lapic: Move LAPIC configuration to MP init
The call to disable_lapic() got removed and with asus/p2b
SeaBIOS payload was unable to load kernel.
The combination of entering SeaBIOS payload with an
enabled lapic but not having programmed LAPIC_LVT0
for DELIVERY_MODE_EXTINT apparently disconnects i8259
PIC interrupt delivery pin.
Change-Id: If51e5d65153a02ac7af191e7897c04bd4e298006
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Change-Id: I4a244df01f6d15cbefb3b01079f6eec943136983
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ib555ce51294c94b22d9a7c0db84d38d7928f7015
Signed-off-by: Igor Bagnucki <igor.bagnucki@3mdeb.com>
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
To prevent to modify original value of wdt_mode, we use setbits32 to
update required bits.
BUG=b:218420108
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I743c1af3583c18ec8500fc1eb89f31cdbce5317c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61729
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SMMSTORE region needs to be 64K aligned or error will be thrown.
Change-Id: I5d4f71f80c3219ac2c7000e1fa95fd04100d9cfe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Instead of having runtime failures that are hard to debug because SMM
debugging is disabled by default assert some properties of fmap at
buildtime.
Change-Id: I5b5b511142d93d5799565a8936e9a087117044b3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Guard macro via CONFIG_INTEL_GMA_ADD_VBT, rather than guarding
each of the calls to it (most of which are currently unguarded).
Test: build google/coral w/ and w/o CONFIG_INTEL_GMA_ADD_VBT selected,
verify VBTs added (or not) to CBFS based on Kconfig selection.
Change-Id: Ic25554cb2c61b81bdb4b0987094c3558e0bbcbd8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Adjust Kconfig so all variants use proper VBTs.
Add Makefile entries for variants which use multiple VBTs.
extracted from ChromeOS firmwares:
Google_Coral.10068.113.0
Google_Pyro.9042.233.0
Google_Reef.9042.233.0
Google_Sand.9042.220.0
Google_Snappy.9042.253.0
Change-Id: I46ad4ec321e32d019e44f0741956b18a464fb8ae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Drop unnecessary switch break after return, to alleviate linter warnings.
Change-Id: I7cc49caaeafb490cb62b75ec5c3ca4822573464b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Several commits were made to the Chromium coral branch
(firmware-coral-10068.B) which were not committed upstream first.
Pull them in here:
486ce56 mainboard/google/coral: Override VBT selection for babymako
c1d7720 Babymako: add touchpad i2c speed config
911d547 mainboard/google/coral: Override VBT selection for babytiger
730a5af Babytiger: add touchpad i2c speed config
724711e rabbid: add the touchpad i2c speed config
80c5d16 mainboard/google/coral: Override VBT selection for babymega
e8931a4 Babymega: add touchpad i2c speed config
These add support for additional coral sub-variants. The I2C speed config
changes were adapted to account for upstream changes not present in the
coral Chromium branch.
Change-Id: Idf2a53a351138aff310385f4026197d74ab6848b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Release firmware on Nasher/Nasher360 are built as coral
sub-variants; remove the old/unused code
Change-Id: Ie8d10a31e663230b7deabf92e1c06cd991bbdccb
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Updating from commit id 73193689c:
2021-12-06 16:47:33 +0100 - (Merge changes I7c9f8490,Ia92c6d19 into integration)
to commit id e0a6a512b:
2022-02-03 22:59:34 +0100 - (Merge changes from topic "msm8916" into integration)
This brings in 324 new commits.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I44bca36f4b05e08fe7d7de0966131be84c0a7d2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
EMPTY_WRAP() might be useful for tests other than CBFS's ones. Move it
to the main tests header file to make it easily accessible.
Change-Id: Ic06c55912488681daf6d2c48cb0c879fa97ba4be
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Updating from commit id 98db386:
2021-08-03 11:57:30 -0700 - (herobrine: Add gsi_fw_blobs and Release Notes)
to commit id 9ab0f0b:
2022-01-18 19:01:30 +0530 - (sc7280: Update AOP firmware to version 379)
This brings in 13 new commits:
9ab0f0b sc7280: Update AOP firmware to version 379
826cb9c sc7180/boot : Update qclib blobs binaries and release notes
ddf67d1 sc7280/ boot and shrm blobs updated
8592f11 sc7280: Update AOP firmware to version 364
aef8a0a sc7280/ boot and shrm blobs updated
c72bc4e sc7280/cpucp: Update cpucp blobs binaries and release notes version from 054 to 060
33e57fe sc7280/boot,/shrm : Update qclib blobs binaries and release notes version 13
511851b sc7180/boot : Update qclib blobs binaries and release notes version 30
f91d0ef herobrine: qc_sec blob update
8c50f78 sc7180/boot : Update qclib blobs binaries and release notes
8523ef4 sc7180/qtiseclib: Update version from 26 to 44
5b77a37 sc7280/qtiseclib: Update version from 33 to 44
4815cc2 sc7280: Update AOP firmware to version 360
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I510141916900507fd29a0e9315a3f8d954bc0cab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Updating from commit id 3f97690:
2021-06-08 09:44:38 -0700 - (microcode-20210608 Release)
to commit id 115c3e4:
2022-02-07 18:23:52 -0800 - (microcode-20220207 Release)
This brings in 1 new commits:
115c3e4 microcode-20220207 Release
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Idb2dcd3e3ef9692e21109ac0e8bdfa9f61740f14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Create the moli variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:214439135
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_MOLI
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I3f3bfd3db12cba8b73b351e7c700b6a58797c906
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
When booting ADL RVP, coreboot is unable to load VBT binary as
makefile will rename VBT binary to "vbt.bin" when building
coreboot.rom.
The reason for having this function is that chromeOS has emerge
tool to streamline the VBT stitching process to support multiple
VBTs for different RVP boards; while we only need 1 vbt for generic
non-chromeOS usage. Hence add a chomeos kconfig to guard this.
TEST=Able to boot ADL RVP DDR5 with DP display.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I5f6f9554b75f4d62198aac9938e65c71c3e7cee9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add Alder Lake and Tiger Lake specific Crash Log and PMC SRAM device
IDs.
Document Number: 619501, 645548
Change-Id: I64b58b8c345bd54774c4dab7b65258714cd8dc9e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add wifi sar for magneto.
Due to fw-config cannot distinguish between magolor and magneto.
Using sku_id to decide to load magneto custom wifi sar.
BUG=b:208261420
TEST= emerge-dedede coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I77f141372ba8e7b8f5849b00e115ad8bb1e7ca00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different _HID
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:204517112
BRANCH=volteer
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5c1c9819af1e0bc2278dadeffb6b19c3f9068f30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different _HID
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:218245715
BRANCH=volteer
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I081dcf5451c82c03592f954ee25267b31ad81753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
use DEV_PTR to get codec HID for simplify the variant.c code
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:204523176
BRANCH=volteer
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Idf5b3661e74a189390d25381e03448c28a966f38
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61671
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Mainboards using Sabrina SoC will be using LP5 memory technology.
Generate the initial set of SPDs for the existing LP5 memory parts.
BUG=b:211510456
TEST=util/spd_tools/bin/spd_gen spd/lp5/memory_parts.json lp5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ibb43f26b36460290341c5ffcad1ef5a2ff1647c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add fw_config NAU88L25B_I2S field, I2S2 configuration and
enabling CnviBtAudioOffload UPD bit.
BUG=none
TEST=temerge-brask coreboot
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Change-Id: Id5da8c5c471be176bc0fe1eda4da7faf8ed2e8d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61404
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
log message
Change-Id: I846c21bd690372ec416fb3d3b3954bf181b0204c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61637
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CBFS MCache size was assigned a value of the coreboot tables entry size
instead of the MCache size.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I8a8c3a10c6032121b4c5246d53d2643742968c09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Some PCIe devices have extended capability lists that contain
multiples instances of the same capability. This patch provides a
function similar to pciexp_find_extended_cap that can be used to
search through multiple instances of the same capability by returning
the offset of the next extended capability of the given type following
the passed-in offset. The base functionality of searching for a given
capability from an offset is extracted to a local helper function and
both pciexp_find_extended_cap and pciexp_find_next_extended_cap use
this helper.
Change-Id: Ie68dc26012ba57650484c4f2ff53cc694a5347aa
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This reverts commit ceaf959678905f44a54a116f37bd15acab5d4608.
The AMD Picasso SoC doesn't support x2APIC and neither advertises the
presence of its support via bit 21 in EAX of CPUID leaf 1 nor has the
bit 10 in the APIC base address MSR 0x1b set, but it does have 0xd CPUID
leaves, so just checking for the presence of that CPUID leaf isn't
sufficient to be sure that EDX of the CPUID leaf 0xb will contain a
valid APIC ID.
In the case of Picasso EDX of the CPUID leaf 0xb returns 0 for all cores
which causes coreboot to get stuck somewhere at the end of MP init.
I'm not 100% sure if we should additionally check bit 21 in EAX of CPUID
function 1 is set instead of adding back the is_x2apic_mode check.
TEST=Mandolin with a Picasso SoC boots again.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If1e3c55ce2d048b14c08e06bb79810179a87993d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The headers added are generated as per Alder Lake N FSP v2503_00.
Changes include:
- Add all header files for Alder Lake N FSP.
- List of header files: FirmwareVersionInfoHob.h, FspmUpd.h, FspsUpd.h,
FspUpd.h, MemInfoHob.h
- Select FSP_HEADER_PATH
BUG=b:213828776
BRANCH=None
Change-Id: I97afa6d47cc825703a8dc82216250bfc5e09dc9b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
volmar boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I36355af771fbf97e655f2fd6e0505c657e0420b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
vell boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0c39d06e3b2f39db88d924205786bfa1b27df3fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
taniks boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icf6cb0d057f9ad3cbcc1155423ed7efa58a46d0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
taeko4es boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I82bdf8a1bfe2df0fc1d50d154def8742714321ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
taeko boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib30815dbe99342b6afd9af9f1aa9ff61c9a4fe80
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
redrix boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ifd69a9c2f1a71aefc19adf6931e10de62d05fb2c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
redrix boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If08ae5c96232efd03d77090c3c6979c77f95c998
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
primus boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I71f7391df6d827b75f87e54e17f6f7983a9e829b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
primus boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3133a992617c833fd13df97795c46ec04ebb8bf9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
kano boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1d8c003b19381e6a76aff8c844546694c5710e53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
gimble boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If71ceb07a9894a0571a9983d008058598693986f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
gimble boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idd398d819dcb30a3ec588ce2ef4562a728f99405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
felwinter boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic1e0bfc53b74bd5af9ac8d598bb80833499dd997
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage'
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id5a2136e57e842fbd0b2c2836833106e7344afee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
Also fix the gpio order of GPP_F19.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
anahera4es boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9a73aca1c364dcbc3f3957cd4193d86f399a40bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
Also fix the gpio order of GPP_F19.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
anahera boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie50ba20a10ded184fd880be9ed288b90d346c22b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Variant should honor locked gpios from baseboard, but not the last.
Variant can add more gpios to lock if needed.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
agah boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia9272f704e5656e6d0dc318dd1b51d50fc549839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add rest of soc sensitive gpios to lock for brask.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
brask boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iad87d13d3df0ad87c075027e3fcc4c75aa711159
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add rest of soc sensitive gpios to lock for brya.
BUG=b:216583542
TEST='emerge-brya coreboot chromeos-bootimage', flash and verify that
brya0 boots successfully to kernel.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I41393e7a0e8bacb3cc98610f7101dabe66308f94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add PAD_NC_LOCK and PAD_CFG_GPI_SCI_LOCK macro to support mainboard
to lock NC and GPI_SCI pins as applicable.
BUG=b:216583542
TEST=build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie44d72f4152b55183d900228df3e3670358f7518
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61655
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
