| Age | Commit message (Collapse) | Author |
|---|
|
Disable unused TCSS Port1.
BUG=b:223082190
TEST=Build
Change-Id: I63f4b7d89a1e37a00c58201ecc88bb336d0932c9
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Acoustic noise mitigation and set slew rate to 1/8
BUG=b:223082189
TEST=build and verified by power team
Change-Id: I256cc57fb54e5d62e22470a01e7efef359d57083
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Nissa boards are curretly using chromeos.fmd file of brya. The SPI flash
layout for brya is of 32MB size, and nissa is expected to have 16MB SPI
NOR flash. The current composition of AP firmware exceeds 16MB. To get
an estimate of the unutilized region in the current flash layout for
nissa, added RW_UNUSED regions. The idea is to reduce the AP firmware
size to under 16MB and to remove the RW_UNUSED regions from the final
fmd file.
Below table gives the size reduction from brya fmd to nissa fmd:
+----------------+-------------------+---------------+
| Region | Earlier size (KB) | New size (KB) |
+================+===================+===============+
| SI_ME | 5116 | 3772 |
+----------------+-------------------+---------------+
| RW_SECTION_A/B | 8192 | 4344 |
+----------------+-------------------+---------------+
| VBLOCK_A/B | 64 | 8 |
+----------------+-------------------+---------------+
| ME_RW_A/B* | 3008 | 1434 |
+----------------+-------------------+---------------+
| RW_LEGACY | 2048 | 1024 |
+----------------+-------------------+---------------+
| RW_ELOG | 16 | 4 |
+----------------+-------------------+---------------+
| SHARED_DATA | 8 | 4 |
+----------------+-------------------+---------------+
| VBLOCK_DEV | 8 | 0 |
+----------------+-------------------+---------------+
| RW_SPD_CACHE | 4 | 0 |
+----------------+-------------------+---------------+
| RW_NVRAM | 24 | 8 |
+----------------+-------------------+---------------+
| WP_RO | 8192 | 4096 |
+----------------+-------------------+---------------+
| GBB | 448 | 12 |
+----------------+-------------------+---------------+
*Based on LZMA compression on ME_RW_A/B regions. With LZMA compression,
this region can be 1434K. Without this, ~665K will be more in each of
these regions.
Patch: https://review.coreboot.org/c/coreboot/+/62358/
BUG=b:202783191
BRANCH=None
TEST=Build and boot Nivviks.
Cq-Depend: chrome-internal:4584911
Change-Id: I24b1c19cb71a54fc916a12668f72193f9689e755
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Change-Id: Ib27149c527015bd54f839994e047f815e8922dc4
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add SOC_INTEL_CSE_LITE_COMPRESS_ME_RW Kconfig to enable compression on
ME_RW blobs. Select the Kconfig to add LZMA compressed ME_RW blobs to
ME_RW_A/B regions.
On ADL-N, this results in savings of ~665KB in each of ME_RW_A/B
regions.
FMAP REGION: ME_RW_A
Name Offset Type Size Comp
me_rw 0x0 raw 1275246 LZMA
(1957888 decompressed)
(empty) 0x1375c0 null 193056 none
FMAP REGION: ME_RW_B
Name Offset Type Size Comp
me_rw 0x0 raw 1275246 LZMA
(1957888 decompressed)
(empty) 0x1375c0 null 193056 none
Change-Id: I2e31c358b4969b077d65ce6369a877914d573aed
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
With LinuxBoot Linux relied on the legacy method of fetching the RSDP
pointer to get ACPI. This uses a more modern approach available since
2018 on the Linux kernel, which involves filling in the zero page.
This method takes precedence over any other method of fetching the
RSDP in Linux (UEFI, Kexec, Legacy/BIOS). Some UEFI zealots are
threatening that legacy code will be removed from Linux so it's best
to already adapt to that possibility.
Tested on Qemu:
- With qemu the RSDP is always in the EBDA, so checking if Linux uses
the provided pointer is better done with a forced bad entry
- With a fake bad pointer Linux correctly does not find RDSP
Change-Id: I688b94608b03b0177c42d2834c7e3beb802ae686
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The ACPI RSDP can only be found in:
- legacy BIOS region
- via UEFI service
On some systems like ARM that legacy BIOS region is not an option, so
to avoid needing UEFI it makes sense to expose the RSDP via a coreboot
table entry.
This also adds the respective unit test.
Change-Id: I591312a2c48f0cbbb03b2787e4b365e9c932afff
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62573
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add prompt to Boot Timeout so that it can be easily configured
from a config file.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I62b8f0a9b5bc0796506b991199a457d6b34ae494
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Hook PCH_DEVFN_CNVI (0c.0) to CnviMode.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8b51e98952a39bd432e9bc63eea57a40dd6cf106
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Correct the offsets used for the keyboard backlight control:
ECRAM_KBL_STATE 0x19
ECRAM_KBL_BRIGHTNESS 0x18
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I23bac43301635e6b18f1cbd28311e7210b049c70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I0324747f936be27ee39e586124005530d5c424b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
If it is not cleared and the number of strings is fewer than last
iteration, the match[3] will keep the last value, which actually
should be empty.
Add assert to make sure the level is a legal value.
BUG=b:222038278
Change-Id: If14e0923fbb1648d83784eb5dc1411c93227db5a
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Discovered this chassis identification number on Dell Precision
T1650 which is much OptiPlex 9010 alike. Precision T1650 is a Mid
Tower (MT) chassis.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I2266fe39606b947a3d30a9462377fd56c39c2fa7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I3487b0ab94e565862ed727e9a91bd1efb364d43d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch replaces remaining `cb_err_t` with `enum cb_err` after commit
hash 69cc557c (commonlib/bsd: Remove cb_err_t) removes majority of
`cb_err_t` instances.
TEST=Able to build the brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3392f9c2cfb4a889a999c8ea25066c89979f0900
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
cb_err_t was meant to be used in place of `enum cb_err` in all
situations, but the choice to use a typedef here seems to be
controversial. We should not be arbitrarily using two different
identifiers for the same thing across the codebase, so since there are
no use cases for serializing enum cb_err at the moment (which would be
the primary reason to typedef a fixed-width integer instead), remove
cb_err_t again for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iaec36210d129db26d51f0a105d3de070c03b686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add PCIe support for MediaTek platform.
Reference:
- MT8195 Register Map V0.3-2, Chapter 3.18 PCIe controller (Page 1250)
- linux/drivers/pci/controller/pcie-mediatek-gen3.c
This code is based on MT8195 platform, but it should be common in each
platform with the same PCIe IP in the future.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ib9b6adaafa20aeee136372ec9564273f86776da0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
ADL encodes CK cycle time as tCKMin whereas Sabrina encodes WCK cycle
time. Encode tCKMin as per the respective advisories.
BUG=None
TEST=Generate the SPD and ensure that tCKMin is encoded accordingly.
Minimum CAS Latency time is also impacted and is encoded accordingly.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I99ada7ead3a75befb0f934af871eecc060adcb26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Git uses the .mailmap file to map author and committer names and email
addresses to canonical real names and email addresses.
Before adding this file, coreboot shows 1388 different author names and
email addresses because of typos, people changing email addresses, and
spelling their names differently.
After adding the file, the number of authors is down to 1016.
I tried to determine the best email address for each person by looking
at what they'd used most recently, but I can't promise that I correctly
picked the right address for everyone. Please take a look to make
sure that your email address and name is correct.
To enable .mailmap parsing globally, use:
$ git config --global log.mailmap true
To enable it just for a single log, run:
$ git log --use-mailmap
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I1f9b9bccc9322799234475a1cebf9808edd25693
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
|
|
Device 1f.7 is TraceHub, not the PCH Thermal device, which doesn't exist
anymore on TGL. Correct the device´s alias.
Reference: Intel doc# 631119-007
Change-Id: I30a4ab1e801f6cdb0f2e03f105bf8cc09592eed8
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I937bdf032e1ed86900334d41655f3e6272f66a6f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Guard Max Charge EC write in Kconfig so it's only used on
platforms that support it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I7be39cd9543c8253d53070950edc6908a21e864a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch aims to make timestamps more consistent in naming,
to follow one pattern. Until now there were many naming patterns:
- TS_START_*/TS_END_*
- TS_BEFORE_*/TS_AFTER_*
- TS_*_START/TS_*_END
This change also aims to indicate, that these timestamps can be used
to create time-ranges, e.g. from TS_BOOTBLOCK_START to TS_BOOTBLOCK_END.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I533e32392224d9b67c37e6a67987b09bf1cf51c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Tested using MrChromeBox's `uefipayload_202107` branch:
* Windows 10
* Ubuntu 20.04
* MX Linux 19.4
* Manjaro 21
No known issues.
https://starlabs.systems/pages/labtop-mk-iv-specification
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idbaa907dc38dc521961806132f21b7a90324ec9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58428
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Split entry, remove Michal Motyl and add Jeff Daly.
Change-Id: Ie572d95c9dd85f59bc3fe47bb61bc6b6866fe4c3
Signed-off-by: Mariusz Szafranski <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Suresh Bellampalli <suresh.bellampalli@intel.com>
Reviewed-by: Jeff Daly <jeffd@silicom-usa.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add ability to use ifdtool to add LAN firmware to image using Kconfig
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Change-Id: Id45ab4b69a85a5f8e52c0c4b130b6d729222b4c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Denverton is a special version of IFD2 flash layout. It defines
10GbE firmware regions (11/12) and the IE (10) region which
other IFD2 platforms do not have. Denverton does not include the
legacy GbE region (3) or the EC region (8) which other IFD2
platforms do have.
TEST='ifdtool -p dnv coreboot.rom' and verify correct output
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Change-Id: I15939ce4672123f39a807d63c13ba7df98c57523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the GPIO configuration of moli
BUG=b:220821454
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I7ec41cb843419c32337b66f3877eda5d730cea35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
When entering suspend, ACPI support is disabled by setting OSFG to 0x00.
This has been moved to be the final action, so it is after saving the
current EC settings.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I5705efab42d2fe0fd5abc6c17eeea46ead27db17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use ECRD function, instead of getting raw values from emem, to avoid a
lack of syncronisation as it uses a mutex.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I31113ef9af3a1e171e3e1f226e7adcfa0fbce61b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the log level to BIOS_NOTICE for the case where the mainboard can
not provide a MAC address since this can be a valid case. Showing this
message with log level BIOS_ERR is not appropriate.
In addition, rephrase the message to make clear that if the mainboard
does not provide a MAC address the one stored in the MAC will be used.
Change-Id: Ibfc58845f0ea47ced048b446e685c4860a29f075
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
When using CNVi WLAN on ADL-N, the internal USB2 port 10 is used for
bluetooth. So update the nivviks overridetree to enable port 10 instead
of port 8, which is the external port used for bluetooth with PCIe WLAN.
BUG=b:222595137
TEST=Bluetooth works on nivviks
Change-Id: Ica2067023125c04fc753eabc944ae29ff59dc864
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
These helpers are not architecture dependent and it might be used for
different platform.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ic13a94d91affb7cf65a2f22f08ea39ed671bc8e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62561
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the BayHub eMMC controller is only going into its reset
state when the RTD3 sequence is initiated. This causes it to
still consume too much power in suspend states. This CL adds the
power enable GPIO into the RTD3 sequence as well, which will turn
off the eMMC controller (a true D3cold state) during the RTD3
sequence.
BUG=b:222436260
TEST=USE="project_primus" emerge-brya coreboot chromeos-bootimage
test suspend stress 100 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I2fec6a30707fb1a258cdcc73b0ce38252b6f77c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The headers added are generated as per FSP v3091_00
Previous FSP version was v2511_04
Changes include:
- Update MemInfoHob.h
BUG=b:222415800
BRANCH=None
Change-Id: I260544e0502174ab141fa31ac78ede803b4f161e
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
cr50 firmware revisions starting at 0.5.5 and later are able to extend
their IRQ pulses to be a minimum of 100us long. This change will enable
cr50 long interrupt pulses when it detects the feature is supported by
the detected firmware version. If the capability was detected, then
GPIO PM will be enabled for the device, otherwise it will be disabled.
BUG=b:202246591
TEST=boot brya0, check console logs for the correct message, and
verify the GPIO PM registers.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iaf333dc0f177e17cd03b36ec7e487fc33bde2b93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61722
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This allows mainboards using an I2C bus to communicate with the cr50
to reuse the functionality related to firmware version and BOARD_CFG.
BUG=b:202246591
TEST=boot on brya0, see cr50 FW version in logs
Change-Id: Ide1a7299936193da3cd3d15fdfd1a80994d70da0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Mainboards accessing the cr50 over an I2C bus may want to reuse some of
the same firmware version and BOARD_CFG logic, therefore refactor this
logic out into a bus-agnostic file, drivers/tpm/cr50.c. This file uses
the new tis_vendor_read/write() functions in order to access the cr50
regardless of the bus which is physically used. In order to leave SPI
devices intact, the tis_vendor_* functions are added to the SPI driver.
BUG=b:202246591
TEST=boot to OS on google/dratini, see the same FW version and board_cfg
console prints as before the change.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie68618cbe026a2b9221f93d0fe41d0b2054e8091
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add GL9750 SD card reader support.
BUG=b:222402409
TEST=Build FW and check device function normally.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Ied36719914de214ae7d810f3d03a508e95fbf66a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Disable unused TCSS PCIe port1
BUG=b:217238553
TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage
Change-Id: I2bdfdb23d010a1e24c986ab52b5cef6eedcb674e
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Windows complains on missing drivers for these ACPI devices. Hide them
from OS as it doesn't influence the hardware operation. Linux can
still probe the drivers correctly.
TEST=Boot Windows 11 and see there are no devices with missing drivers.
Boot Ubuntu 20.04 and check that drivers corresponding to ACPI HIDs are
still probed.
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: I6c30c08ab730749bddef7ea67c7470c1554bd572
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Vell has a keyboard MCU connected to USB2 port 7. This patch enables
the port.
localhost# usb_updater2 -f
Found device.
found interface 0 endpoint 1, chunk_len 64
READY
-------
start
target running protocol version 6 (type 1)
maximum PDU size: 4096
Flash protection status: 0000
version: prism_v2.0.12137+c4ae1432f5
key_version: 1
min_rollback: 0
offset: writable at 0xc000
Current versions:
Writable prism_v2.0.12137+c4ae1432f5
BUG=b:203664745,b:211496726
TEST=Run 'usb_updater2 -f' on Vell.
Change-Id: Iad2140dbdf5e34332388f3f43b3ede3d22e73087
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
ChromeOS considers the WWAN devices to be untrusted, therefore enable
the new DmaProperty in the WWAN's _DSD to indicate to the OS that these
devices should have IOMMU restrictions applied to them.
BUG=b:215424986
BRANCH=brya
TEST=dump SSDT
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9c9e73b7ea0575ab87cc980fb4786338047155de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Similar to commit 09c047c, the WWAN device might be considered an
untrusted device by some platforms, therefore add an option to add the
same `DmaProperty` to the WWAN _DSD.
BUG=b:215424986
BRANCH=brya
TEST=dump SSDT, see new property
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If485ac5314fae6e6faefac43fcfcea4f4cdd02c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Commit ebf14826
[mb/google/hatch/var/jinlon: Switch to using device pointers]
broke jinlon boards without an electronic privacy screen (EPS) by
disabling the parent device (iGPU) instead of the EPS when determined to
be not present via SKU ID.
Commit c5a3a4a6
[mb/google/hatch (baseboard): add ACPI backlight support]
broke EPS detection by adding a duplicate iGPU device to the devicetree,
resulting in the EPS entry being skipped.
Fix both of these issues by assigning the device alias to the EPS child
device, not the parent (iGPU). Rename the alias for clarity, and combine
the duplicate device definitions for the iGPU.
Test: build/boot google/jinlon SKU w/o EPS, observe GPU functional
in both firmware boot screens and Linux OS.
Change-Id: I0615ce361497abe6872085b0dec83292607e53dd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62593
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 017b5c453a72f57ec785da1764939e24651ac5eb
[ec/google/chromeec/acpi: Rename EC_ENABLE_TABLET_EVENT config]
broke tablet mode on google/caroline and cave in mainline Linux kernels
by changing the inclusion of the ChromeEC tablet mode ACPI handler. Fix
this by addding it back (using the updated name guarding the inclusion
of the tmbc ACPI).
Test: build/boot google/cave under Linux 5.16, observe tablet mode
handled correctly.
Change-Id: Ie0ae5b6a61f104b5e973383344d289cc2e2a7b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The patch uses Kconfigs for Descriptor Region and Descriptor Region
size instead of locally defined macros
TEST=Build and boot Brya board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3f9461c8604383f995a4438f45286b14fb94deaa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
|
|
The patch defines Kconfigs for FMAP Descriptor Region and Descriptor
Region size. The Kconfigs will be used by follow-up patches.
TEST=Build Brya code
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ia3481acefbda885617607675aef2afbb81c21c77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BT didn't work due to commit 03c0853f4d58c73.
Commit 03c0853f4d58c73 accidentally set the Bluetooth USB2 port
to "empty", therefore re-enable USB2 port 9.
BUG=b:217238553, b:222238381
TEST=build and verfied BT work/suspend successfully
Change-Id: Ie94ef847fc130019f1e06983fc5039f1f564cd3a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change is to move MPTS (Mainboard Prepare To Sleep) method from
wwan_power.asl to SSDT.
MPTS is mainboard-specific method, while wwan_power.asl is meant for
WWAN from its name.
Having fixed MPTS method (i.e. DSDT) can not cover the case where device
only presents and certain CBI bit(s) is(are) set.
In Redrix and Brya, there are SKUs with or without 5G, 4G device. For
those with 4G, MPTS method should be different. For those with no WWAN
device, no MPTS is needed.
Having MPTS generating in SSDT also eliminates the need for introducing
Kconfig flags to support different devices in the future.
MPTS method is created inside mainboard_fill_ssdt function in which the
corresponding variant function is called.
This will generate the following for the mainboard:
Scope (\_SB)
{
Method (MPTS, 1, Serialized)
{
Local0 = \_SB.PCI0.RP01.RTD3._STA ()
If ((Local0 == One))
{
\_SB.PCI0.RP01.PXSX.DPTS (Arg0)
}
}
}
Test:
Check the SSDT for MPTS method under \_SB after boot to OS
Use shutdown command and check the GPIO pins from logical analyzer
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I0f0b7638e90a7862173fca99305398bb250373e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add HID driver for i2c-1 for Ilitek touchscreen.
BRANCH=None
BUG=b:187289163
TEST=Build and flash coreboot; confirm an entry for hidraw for I2C-1 for
Ilitek touchscreen.
Change-Id: I9e42c36a35654cf3e2b41f78b209f4b89e8b05bd
Signed-off-by: Rehan Ghori <rehang@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
coreboot recently introduced non-printable loglevel markers in the CBMEM
console. Payloads were generally unaffected since they don't use log
levels and it is still legal to append lines without a marker to the
log. However, payloads using cbmem_console_snapshot() to display
existing logs from coreboot have started seeing '?' characters in place
of the markers. This patch fixes the issue by filtering out marker
characters.
BUG=b:221909874
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4a9e5d464508320cf43ea572d62896d38c2a128d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This revert commit acb17fec34a609c5b674ad0d2af04d47800530e2.
This issue was fixed in the OS, therefore the workaround can be
reverted.
BUG=b:210497855
BRANCH=firmware-brya-14505.B
TEST=build coreboot and boot into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ic836e0cf53c2f9d30bd12851be285d864b2256b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move some structures to common folder (CB:61293), so we need to update
header version.
BUG=none
TEST=dram calibration pass
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: Id82cbef9cb10dba71489ea96f67c329de9aadc49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Move some structures to common folder (CB:61293), so we need to update
header version for this.
BUG=none
TEST=dram calibration pass
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I8cf12f4967af116eaef88c1f688567f1da9fa6e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
SMMSTORE needs to have 64k size (minimum) and have 64k alignment as
enforced by asserts added in commit 1ba6049
[drivers/smmstore/store.c: Add static assertion based on fmap].
Adjust size and alignment of SMMSTORE region in FMAP to ensure those conditions are met.
Test: build google/morphius without asserts being tripped for above conditions.
Change-Id: Ied04e93379e1507f5e6b2a1b71e4098a4561e5d8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GPP_S6 was accidentally configured twice instead of configuring GPP_S7.
So configure GPP_S7 according to the schematics.
BUG=b:222218450
TEST=WCAM DMIC works on nivviks
Change-Id: I5de36aaa504a8856803c783564162c36416b50b7
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62511
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Infineon TPM 1.2 used on glados boards doesn't use a PIRQ;
Linux only works with 'tpm.tis_interrupts=0" and Windows fails to
init the TPM citing a lack of available resources. With the PIRQ
removed, both Linux and Windows are happy / the TPM is available
for use.
Test: build/boot Linux 5.16.x and Windows 11 on google/chell
Change-Id: I544695505291bbebe062df636cc8ddd139c08c2b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change loglevel prefix "BIOS_ERR" to "BIOS_DEBUG".
BUG=b:220639445
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ie3de63fc13e7a5ed6a4b4617542851782fbb6f00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62508
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a comment to point out that the read_resources functions aren't
missing a pci_dev_read_resources call that would add the resources for
the BARs of the PC device.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie480832e0d7954135d2171dda986e477ef7b6c09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
In the northbridge's and root complex' read_resources function, the
GNB IOAPIC resource used MMIO base address of the GNB IOAPIC as index
which might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 fec01000 base fec01000 limit fec01fff mem (fixed)
After: PCI: 00:00.0 0d base fec01000 limit fec01fff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8061364879d772469882fc060f92676de6f600a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
In the northbridge's and root complex' read_resources function, the
mmconf resource used the number of the MMIO_CONF_BASE MSR as index which
might be misleading. Instead use idx++ as a unique index for this
resource.
TEST=Resource allocator doesn't complain and no related warnings or
errors in dmesg. The update_constraints console output changes like
expected:
Before: PCI: 00:00.0 c0010058 base f8000000 limit fbffffff mem (fixed)
After: PCI: 00:00.0 06 base f8000000 limit fbffffff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id66c6153fad86bed36db7bd2455075f4a0850750
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
TPM1_MODE and TPM2_MODE defines have to be added to vboot and payload
cflags to make them build correctly without requiring payloads to provide
defines.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I567a9f04d7089699840dc7e0a063cf3030fb934b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
In order to align with established standards for establishing DMA
boundaries[1] from ACPI, the UntrustedDevice property has been renamed
to DmaProperty, which follows Microsoft's implementation. After
discussions with Microsoft, they have agreed to make the `UID` property
optional, so it is left out here, and instead it can be applied to:
1) Internal PCI devices
2) PCIe root ports
3) Downstream PCI(e) devices
[1]: https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
BUG=b:215424986
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Id70e916532e3d3d70305fc61473da28c702fc397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
After the patch that moved the generation of the PPKG object to
Stoneyridge's acpi.c, only the PNOT object remained in its cpu.asl, so
rename it to pnot.asl.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0deb2d75cae98b8fcd31297d7fac5f27525efe65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Stoneyridge with the other AMD SoCs. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=None, but equivalent change on Picasso was verified to not break
anything on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib42d718102151a72a5fe812e83eb2eb4f9e7b611
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
After the patch that moved the generation of the PPKG object to
Picasso's acpi.c, only the PNOT object remained in its cpu.asl, so
rename it to pnot.asl.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic77dacb146aa823fc99f779f465fff28b2aead68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Generate the PPKG object in the generate_cpu_entries function instead of
generating the PCNT object that is the used in the PPKG method in
cpu.asl to provide the PPKG object. This both simplifies the code and
aligns Picasso with Cezanne and Sabrina. This will also make the code
behave correctly in a case where the number of CPU cores/threads isn't a
power of two.
TEST=Mandolin still boots successfully to Linux desktop and dmesg
doesn't show any any possibly related problems.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifb84435345c6d8c5d11a8b42e5538cfb86432780
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
If B1FC (Battery Full Capacity) is higher than B1DC (Battery Design
Capacity), only report the design capacity. This handles cases where
the battery calibration is incorrect, and the battery runs out before
the OS thinks it's empty.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib3e4769c809b69e0a237b5f043e6c41c12d53752
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Disabled G2touch driver and add ELAN touchpanel driver for vell.
Due to incorrect BIOS setting, touch screen IC FW can't update and work.
According to ELAN's recommendations, we coreect the ELAN2513 driver's setting and change I2C address to 0x10
BUG=b:221340736
TEST=emerge-brya coreboot and can flash touch screen FW
Change-Id: I22f04fa21b542e21e88c46547779cfb55beb5c12
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Since we want to read the non-x86 CBMEMC from SMM we need to be stricter
on where we read from. This change forces the verstage binary and x86
code to agree on the CBMEMC transfer buffer location and size.
BUG=b:221231786
TEST=Boot guybrush and verify verstage transfer buffer still ends up in
cbmem
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida7d50bef46f280be0db1e1f185b46abb0ae5c8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure GPIOs according to schematics
BUG=b:218786363
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I939bc5f8963e9cba762adeb4828729fd14e29520
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
We don't need to force the caller to look up and cast the transfer
region. We can do it in the function.
BUG=b:221231786
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib46a673ef5a43deb56a6d522152085036a47ab66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
I want to reuse the transfer buffer methods in SMM, so I need to add
them into their own file. I renamed `setup_cbmem_console` to
`replay_transfer_buffer_cbmemc` so it has a more descriptive name. I
also fixed the comment on `verify_psp_transfer_buf`.
BUG=b:221231786
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4f3a8b414b91f601c3a9c3dc7af8f388286fe4da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
We need to save the transfer buffer so we can transfer the cbmem
console and timestamps into x86 DRAM.
BUG=b:221231786
TEST=Boot guybrush and verify S0i3 resume works. Also dumped the
transfer buffer from the OS and verified the console contents got
transferred.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d3b34c90e0e18609b0c6a0cdedab35aeefbd84b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
All SoCs/chipsets that select ARCH_X86 will end up using the
implementation in cpu/x86/lapic/lapic.c, so to avoid confusion, drop the
unused weak implementation that returns a different value.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iffcd8c80260f9a7d81dda41a0ad08bffc7620c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
In order to achieve a stable eMMC interface disable the HS400 capability
of the host controller. This will result in an operating mode of maximum
HS200 (200 MHz single data rate) which leads to a more relaxed timing.
Change-Id: I0e125dd569b00f59ae0fd2f76169c4461291b47a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The QEMU POWER9 target is supported since coreboot version 4.15.
Documentation is available in the tree, but it's not referenced from
the mainboard index page. Fix that.
Change-Id: Ic3b98735840c146cb0bfb122df0e6f762c2beeca
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fix spelling and use the one from their website qemu.org.
Change-Id: I36a88985ce3a7c59b732c1ca3198d86a591de6bd
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The Supermicro X9SAE target is supported since coreboot version 4.15.
Documentation is available in the tree, but it's not referenced from
the mainboard index page. Fix that.
Change-Id: I5d3d0b5b935f1a3ea353a3d9e39208db7c7895ef
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fix the spelling and use the one from their website supermicro.com
Change-Id: Id630d9d130082fb38f9151e0dfb6f6fbb5a2789d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Both the secondary and subordinate bus numbers are configured in this
function but it's not easy to search for in the tree as the PCI writes
are hidden inside a bigger write to 'PCI_PRIMARY_BUS'. Use separate
variables and PCI config writes to improve the readability.
Change-Id: I3bafd6a2e1d3a0b8d1d43997868a787ce3940ca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The XTAL 26MHz test failed on krabby, so we adjust RTC capid from
default value 0x88 to 0xC0 for MT8186. We also add a new log message
to show the capid value which is read from MT6366.
This implementation is according to chapter 5.13 in MT8186 Functional
Specification.
BUG=b:218439447
TEST=set capid to 0xc0.
TEST=XTAL 26MHz test passed.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I16ab46a5697d304e8001de231ffc9b7b7a2f9282
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
RTC_GPIO_USER_MASK is not used in any drivers, so we remove them.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I0a15d5da142bb38feb595610d69566330e31fedd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
google/brask is using SODIMMs for DRAM. Reading spd data is
surprisingly slow (~170 ms), therefore enable the SPD cache.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=run on the device and measure the boot time decrease.
Change-Id: If0a0072160a48b607ad17c0a1819ab49eaad92db
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Align the setting with the adlrvp
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=build pass and works correctly in the brask
Change-Id: Ia4c889e7dd065632e180cf983c7c5ece0c461edd
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
In order to cache the spd data which reads from the memory module, we
add SPD_CACHE_ENABLE option to enable the cache for the spd data. If
this option is enabled, the RW_SPD_CACHE region needs to be added to
the flash layout for caching the data.
Since the user may remove the memory module after the bios caching the
data, we need to add the invalidate flag to invalidate the mrc cache.
Otherwise, the bios will use the mrc cache and can make the device
malfunction.
BUG=b:200243989
BRANCH=firmware-brya-14505.B
TEST=build pass and enable this feature to the brask
the device could speed up around 150ms with this feature.
Change-Id: If7625a00c865dc268e2a22efd71b34b40c40877b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62294
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's easier to read and to add new packages when each package is on its
own line and they're sorted alphabetically.
Indenting them also makes it easier to see what's getting installed and
what's a command.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ibfe297bd408ed0783fcff09c1ecb5672fe785c48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62446
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The linkchecker tool is now being used to find broken links in our
websites. Since it's not needed for building anything, just add it to
the jenkins-node Dockerfile instead.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Iac2246b5378e556b5cd9f2107fc5a7e51d583b5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62445
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch removes Rcomp settings. In MRC design, it checks if the
Rcomp settings from the board is 0 or null, if so, it uses the
recommended Rcomp values. Otherwise, it uses the Rcomp settings passed
from the UPD. From the change history of MRC, we're chasing a moving
target. This RCOMP setting in coreboot is an old setting while the
Rcomp settins in MRC are optimized settings. Moving forward, if there
is a new stepping, it might be changed again which increases the
maintenance effort in coreboot. IMHO, we should let MRC to set the
optimized RCOMP values for the design.
BUG=b:219378758
TEST=emerge-byra coreboot chromeos-bootimage and boots up with QS and
PRQ CPUs. Checks with MRC log and ensure the RCOMP settings are
filled properly by MRC.
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Change-Id: I8547e187b74f9b2cee57ddad2883d60c05d0b9fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
With GPP_B3 locked, primus eMMC SKU encounter eMMC storage lost after
warm reboot.
Config GPP_B3 unlocked to make reboot works on primus. Also set
GPP_B3 to low in early_gpio_table to meet eMMC-PCIe bridge IC power
on sequence.
BUG=b:221488504
TEST=USE="project_primus" emerge-brya coreboo chromeos-bootimage
test reboot 30 cycles passed on primus.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ifd5f9d59d33cd1c5ebe0454ab3aa4c5641c16ff6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
If an AMD FSP binary has no valid image revision information, print a
warning instead of an error.
Change-Id: Ie9c5a387b81205fe93382778090260e41e261776
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62349
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Chausie doesn't have recovery mode buttons so it's impossible to
manually enter recovery mode to enable developer mode. This means we
need to force developer mode.
BUG=none
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id0b08ee8e009e8603f63e691b5a7a2ac04e1fc3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In order to abstract bus-specific logic from TPM logic, the prototype
for two vendor-specific tis functions are added in this
patch. tis_vendor_read() can be used to read directly from TPM
registers, and tis_vendor_write() can be used to write directly to TPM
registers.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I939cf5b6620b6f5f6d454c53fcaf37c153702acc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Instead of using raw integers to indicate success/failure, enum cb_err
can be used to makes things clearer, so this patch converts most
functions to return that instead of int.
TEST=boot to OS on google/dratini, no TPM errors seen
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ifb749c931fe008b16d42fcf157af820ec8fbf5ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable STT and decrease sustained_power_limit_mW to 12W
BUG=b:219616787
BRANCH=guybrush
TEST=emerge-guybrush coreboot
update the thermal setting value by measurement and
pass the thermal performance test
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I5b7b0156fb4a1e2be8528a5787ed82acff93f06c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
coreboot should skip sending EOP during S3 resume since CSE doesn't
require EOP in resume path.
Currently EOP is being sent during PAYLOAD_BOOT or PAYLOAD_LOAD stage
which doesn't get called during S3 resume.
In case EOP is moved in earlier stage, coreboot might send EOP in S3
resume as well. This patch adds check before calling cse_send_eop.
BUG=b:211085685
BRANCH=None
TEST=Check by moving EOP to earlier stage. EOP sending is skipped during
S3 resume.
Change-Id: I8f22446974bc1e7b2d57468633c36bb99ffe1436
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Move the instructions for flashing coreboot with fwupd to common
directory as the process is identical across all models and variants.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I293acf962b32c81fdf482e0df15363e1cffa39bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iddbf2022d03735d6a0e6d098c21643f5fdc875f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
