1 files changed, 0 insertions, 137 deletions
diff --git a/src/mainboard/olpc/btest/mainboard.c b/src/mainboard/olpc/btest/mainboard.c
deleted file mode 100644
index c6b86ef18d..0000000000
--- a/src/mainboard/olpc/btest/mainboard.c
+++ /dev/null
@@ -1,137 +0,0 @@
-#include <console/console.h>
-#include <device/device.h>
-#include <device/pci.h>
-#include <device/pci_ids.h>
-#include <device/pci_ops.h>
-#include <arch/io.h>
-#include <pc80/mc146818rtc.h>
-#include "chip.h"
-#include "southbridge/amd/cs5536/cs5536_smbus2.h"
-#include <cpu/amd/vr.h>
-
-/* Borrowed from mc146818rtc.c */
-
-#define CMOS_READ(addr) ({ \
-		outb((addr),RTC_PORT(0)); \
-		inb(RTC_PORT(1)); \
-		})
-
-#define CMOS_WRITE(val, addr) ({ \
-		outb((addr),RTC_PORT(0)); \
-		outb((val),RTC_PORT(1)); \
-		})
-
-static void write_bit(unsigned char val) {
-
-	unsigned char byte = CMOS_READ(440 / 8);
-
-	/* Don't change it if its already set */
-
-	if ((byte & 1) == (val & 1))
-		return;
-
-	byte &= ~1;
-	byte |= val & 1;
-	CMOS_WRITE(val, 440/8);
-}
-
-static unsigned short _getsmbusbase(void) {
-	unsigned devfn = PCI_DEVFN(0xf, 0);
-	device_t dev = dev_find_slot(0x0, devfn);
-	unsigned long addr = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
-
-	return (unsigned short) (addr & ~1);
-}
-
-static void init_dcon(void) {
-
-  int ret = 1;
-  unsigned short rev = 0;
-  unsigned short iobase = _getsmbusbase();
-
-  printk(BIOS_DEBUG, "CHECKING FOR DCON (%x)\n", iobase);
-
-  /* Get the IO base for the SMBUS */
-
-  rev = do_smbus_read_word(iobase, 0x0D << 1, 0x00);
-
-  if (rev & 0xDC00) {
-	printk(BIOS_DEBUG, "DCON FOUND - REV %x\n", rev);
-
-	/* Enable the DCON */
-	ret = do_smbus_write_word(iobase, 0x0D << 1, 0x01, 0x0069);
-	if (ret != 0)
-		printk(BIOS_DEBUG, "DCON ENABLE FAILED %d\n", ret);
-  }
-  else
-	  printk(BIOS_DEBUG, "DCON NOT FOUND (%x)\n", rev);
-
-  write_bit(rev > 0 ? 1 : 0);
-}
-
-static void
-init_cafe_irq(void){
-	const unsigned char slots_cafe[4] = {11, 0, 0, 0};
-
-
-	/* CAFE PCI slots */
-	pci_assign_irqs(0, 0x0C, slots_cafe);
-
-	/* Make the pin assignments - NOTENOTENOTE:  This should be
-	  * configurable!
-	  */
-
-	/* Configure the GPIO pins to use - class 0, index 9 to configure
-	  * AB.  Write 0xFF to disable
-	  */
-
-	vrWrite(0x9, 0XFF00);
-
-	/* Configure the GPIO pins to use - class 0, index A to configure
-	  * CD.  Write 0xFF to disable
-	  */
-
-       vrWrite(0xA, 0xFFFF);
-
-}
-
-
-static void init(struct device *dev) {
-/*
-	unsigned bus = 0;
-	unsigned devfn = PCI_DEVFN(0xf, 4);
-	device_t usb = NULL;
-	unsigned char usbirq = 0xa;
-*/
-
-	printk(BIOS_DEBUG, "OLPC BTEST ENTER %s\n", __func__);
-
-#if 0
-	/* I can't think of any reason NOT to just set this. If it turns out we want this to be
-	  * conditional we can make it a config variable later.
-	  */
-
-	printk(BIOS_DEBUG, "%s (%x,%x)SET USB PCI interrupt line to %d\n",
-		__func__, bus, devfn, usbirq);
-	usb = dev_find_slot(bus, devfn);
-	if (! usb){
-		printk(BIOS_ERR, "Could not find USB\n");
-	} else {
-		pci_write_config8(usb, PCI_INTERRUPT_LINE, usbirq);
-	}
-#endif
-
-	init_dcon();
-	init_cafe_irq();
-	printk(BIOS_DEBUG, "OLPC BTEST EXIT %s\n", __func__);
-}
-
-static void enable_dev(struct device *dev)
-{
-        dev->ops->init = init;
-}
-
-struct chip_operations mainboard_ops = {
-	CHIP_NAME("OLPC btest Mainboard")
-        .enable_dev = enable_dev,
-};