mb/starlabs: Rename LabTop to StarBook

The LabTop was renamed to StarBook since the release of the Mk V.
This change keeps the directory name more relevant, as there are
more boards using the name StarBook.

Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3513fb56c1adf663ed7bcdade2cc52cd8c0d6f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65640
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>

1 files changed, 234 insertions, 0 deletions

diff --git a/src/mainboard/starlabs/starbook/variants/tgl/devicetree.cb b/src/mainboard/starlabs/starbook/variants/tgl/devicetree.cb
new file mode 100644
index 0000000000..c5f7040058
--- /dev/null
+++ b/src/mainboard/starlabs/starbook/variants/tgl/devicetree.cb
@@ -0,0 +1,234 @@
+chip soc/intel/tigerlake
+# CPU
+	# Enable Enhanced Intel SpeedStep
+	register "eist_enable"			= "1"
+
+	# Graphics
+	# Not used but timings left for reference
+	# register "panel_cfg" = "{
+	#	.up_delay_ms			= 2000,				// T3
+	#	.backlight_on_delay_ms		= 0,				// T7
+	#	.backlight_off_delay_ms		= 2000,				// T9
+	#	.down_delay_ms			= 500,				// T10
+	#	.cycle_delay_ms			= 500,				// T12
+	#	.backlight_pwm_hz		= 200,				// PWM
+	# }"
+
+	# FSP Memory
+	register "CnviBtCore"			= "true"
+	register "CnviBtAudioOffload"		= "1"
+	register "enable_c6dram"		= "1"
+	register "SaGv"				= "SaGv_Enabled"
+	register "TcssD3ColdDisable"		= "1"
+
+	# FSP Silicon
+	# Serial I/O
+	register "SerialIoI2cMode" = "{
+		[PchSerialIoIndexI2C0]		= PchSerialIoPci,
+		[PchSerialIoIndexI2C4]		= PchSerialIoSkipInit,
+	}"
+
+	register "SerialIoUartMode" = "{
+		[PchSerialIoIndexUART2]		= PchSerialIoSkipInit,
+	}"
+
+	# Power
+	register "PchPmSlpS3MinAssert"		= "2"				# 50ms
+	register "PchPmSlpS4MinAssert"		= "3"				# 1s
+	register "PchPmSlpSusMinAssert"		= "3"				# 500ms
+	register "PchPmSlpAMinAssert"		= "3"				# 2s
+
+	# PM Util
+	# GPE configuration
+	# Note that GPE events called out in ASL code rely on this
+	# route. i.e. If this route changes then the affected GPE
+	# offset bits also need to be changed.
+	# sudo devmem2 0xfe001920 (pmc_bar + GPIO_GPE_CFG)
+	register "pmc_gpe0_dw0"			= "GPP_B"
+	register "pmc_gpe0_dw1"			= "GPP_C"
+	register "pmc_gpe0_dw2"			= "GPP_E"
+
+	# Enable the correct decode ranges on the LPC bus.
+	register "lpc_ioe"			= "LPC_IOE_EC_4E_4F |
+						   LPC_IOE_SUPERIO_2E_2F |
+						   LPC_IOE_KBC_60_64 |
+						   LPC_IOE_EC_62_66 |
+						   LPC_IOE_LGE_200"
+
+	# PCIe Clock
+	register "PcieClkSrcClkReq[0]"		= "PCIE_CLK_NOTUSED"
+	register "PcieClkSrcClkReq[1]"		= "PCIE_CLK_NOTUSED"
+	register "PcieClkSrcClkReq[2]"		= "PCIE_CLK_NOTUSED"
+	register "PcieClkSrcClkReq[4]"		= "PCIE_CLK_NOTUSED"
+	register "PcieClkSrcClkReq[5]"		= "PCIE_CLK_NOTUSED"
+	register "PcieClkSrcClkReq[6]"		= "PCIE_CLK_NOTUSED"
+
+# Actual device tree.
+	device cpu_cluster 0 on
+		device lapic 0 on end
+	end
+
+	device domain 0 on
+		device pci 00.0 on  end						# Host Bridge
+		device pci 02.0 on  end						# Integrated Graphics Device
+		device pci 04.0 on  end						# SA Thermal Device
+		device pci 05.0 off end						# IPU
+		device pci 06.0 off end						# PEG60
+		device pci 07.0 on  end						# TBT_PCIe0
+		device pci 07.1 off end						# TBT_PCIe1
+		device pci 07.2 off end						# TBT_PCIe2
+		device pci 07.3 off end						# TBT_PCIe3
+		device pci 08.0 on  end						# Gaussian Mixture Model
+		device pci 09.0 off end						# NPK
+		device pci 0a.0 off end						# Crash-log SRAM
+		device pci 0d.0 on						# USB xHCI
+			register "UsbTcPortEn"			= "1"
+			register "TcssXhciEn"			= "1"
+			register "TcssAuxOri"			= "0"
+		end
+		device pci 0d.1 off end						# USB xDCI (OTG)
+		device pci 0d.2 on						# TBT DMA0
+			chip drivers/intel/usb4/retimer
+				register "dfp[0].power_gpio"	= "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A23)"
+				use tcss_usb3_port1 as dfp[0].typec_port
+				device generic 0 on end
+			end
+		end
+		device pci 0d.3 off end						# TBT
+		device pci 0e.0 off end						# VMD
+		device pci 10.6 off end
+		device pci 10.7 off end
+		device pci 12.0 off end						# Thermal Subsystem
+		device pci 12.6 off end						# GSPI #2
+		device pci 14.0 on						# USB xHCI
+			# Motherboard USB Type C
+			register "usb2_ports[0]"		= "USB2_PORT_TYPE_C(OC_SKIP)"
+			register "tcss_ports[0]"		= "TCSS_PORT_DEFAULT(OC_SKIP)"
+
+			# Motherboard USB 3.0
+			register "usb2_ports[1]"		= "USB2_PORT_MID(OC_SKIP)"
+			register "usb3_ports[0]"		= "USB3_PORT_DEFAULT(OC_SKIP)"
+
+			# Daughterboard USB 3.0
+			register "usb2_ports[2]"		= "USB2_PORT_MID(OC_SKIP)"
+			register "usb3_ports[1]"		= "USB3_PORT_DEFAULT(OC_SKIP)"
+
+			# Daughterboard SD Card
+			register "usb2_ports[5]"		= "USB2_PORT_MID(OC_SKIP)"
+
+			# Webcam
+			register "usb2_ports[CONFIG_CCD_PORT]"	= "USB2_PORT_MID(OC_SKIP)"
+
+			# Internal Bluetooth
+			register "usb2_ports[9]"		= "USB2_PORT_MID(OC_SKIP)"
+		end
+		device pci 14.1 off end						# USB xDCI (OTG)
+		device pci 14.2 on  end						# USB xDCI (OTG)
+		device pci 14.3 on						# CNVi
+			chip drivers/wifi/generic
+				register "wake"			= "GPE0_PME_B0"
+				device generic 0 on end
+			end
+		end
+		device pci 15.0 on						# I2C0
+			chip drivers/i2c/hid
+				register "generic.hid"		= ""STAR0001""
+				register "generic.desc"		= ""Touchpad""
+				register "generic.irq"		= "ACPI_IRQ_LEVEL_LOW(GPP_C8_IRQ)"
+				register "generic.probed"	= "1"
+				register "hid_desc_reg_offset"	= "0x20"
+				device i2c 2c on end
+			end
+		end
+		device pci 15.1 off end						# I2C1
+		device pci 15.2 off end						# I2C2
+		device pci 15.3 off end						# I2C3
+		device pci 16.0 on  end						# Management Engine Interface 1
+		device pci 16.1 off end						# Management Engine Interface 2
+		device pci 16.2 off end						# Management Engine IDE-R
+		device pci 16.3 off end						# Management Engine KT Redirection
+		device pci 16.4 off end						# Management Engine Interface 3
+		device pci 16.5 off end						# Management Engine Interface 4
+		device pci 17.0 on						# SATA
+			register "SataSalpSupport"		= "1"
+			# Port 1
+			register "SataPortsEnable[1]"		= "1"
+			register "SataPortsDevSlp[1]"		= "1"
+		end
+		device pci 19.0 on  end						# I2C4
+		device pci 19.1 off end						# I2C5
+		device pci 19.2 on  end						# UART #2
+		device pci 1c.0 off end						# PCI Express Port 1
+		device pci 1c.1 off end						# PCI Express Port 2
+		device pci 1c.2 off end						# PCI Express Port 3
+		device pci 1c.3 off end						# PCI Express Port 4
+		device pci 1c.4 off end						# PCI Express Port 5
+		device pci 1c.5 off end						# PCI Express Port 6
+		device pci 1c.6 off end						# PCI Express Port 7
+		device pci 1c.7 off end						# PCI Express Port 8
+		device pci 1d.0 on						# PCI Express Port 9 (SSD x4)
+			register "HybridStorageMode"		= "0"
+			register "PcieRpEnable[8]"		= "1"
+			register "PcieRpLtrEnable[8]"		= "1"
+			register "PcieClkSrcUsage[3]"		= "0x08"
+			register "PcieClkSrcClkReq[3]"		= "3"
+			register "PcieRpSlotImplemented[8]"	= "1"
+			smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" "M.2/M 2280" "SlotDataBusWidth4X"
+			chip soc/intel/common/block/pcie/rtd3
+				register "enable_gpio"		= "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D16)"
+				register "reset_gpio"		= "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)"
+				register "srcclk_pin"		= "3"
+				device generic 0 on end
+			end
+		end
+		device pci 1d.1 off end						# PCI Express Port 10
+		device pci 1d.2 off end						# PCI Express Port 11
+		device pci 1d.3 off end						# PCI Express Port 12
+		device pci 1e.0 off end						# UART #0
+		device pci 1e.1 off end						# UART #1
+		device pci 1e.2 off end						# GSPI #0
+		device pci 1e.3 on  end						# GSPI #1
+		device pci 1f.0 on						# LPC Interface
+			register "gen1_dec"			= "0x000c1641"
+			register "gen2_dec"			= "0x000c0681"
+			register "gen3_dec"			= "0x000c0081"
+
+			chip drivers/pc80/tpm
+				device pnp 0c31.0 on end
+			end
+
+			chip ec/starlabs/merlin
+				# Port pair 4Eh/4Fh
+				device pnp 4e.00 on  end			# IO Interface
+				device pnp 4e.01 off end			# Com 1
+				device pnp 4e.02 off end			# Com 2
+				device pnp 4e.04 off end			# System Wake-Up
+				device pnp 4e.05 off end			# PS/2 Mouse
+				device pnp 4e.06 on				# PS/2 Keyboard
+					io 0x60			= 0x0060
+					io 0x62			= 0x0064
+					irq 0x70		= 1
+				end
+				device pnp 4e.0a off end			# Consumer IR
+				device pnp 4e.0f off end			# Shared Memory/Flash Interface
+				device pnp 4e.10 off end			# RTC-like Timer
+				device pnp 4e.11 off end			# Power Management Channel 1
+				device pnp 4e.12 off end			# Power Management Channel 2
+				device pnp 4e.13 off end			# Serial Peripheral Interface
+				device pnp 4e.14 off end			# Platform EC Interface
+				device pnp 4e.17 off end			# Power Management Channel 3
+				device pnp 4e.18 off end			# Power Management Channel 4
+				device pnp 4e.19 off end			# Power Management Channel 5
+			end
+		end
+		device pci 1f.1 off end						# P2SB
+		device pci 1f.2 hidden end					# Power Management Controller
+		device pci 1f.3 on						# Intel HDA
+			register "PchHdaAudioLinkHdaEnable"	= "1"
+		end
+		device pci 1f.4 on  end						# SMBus
+		device pci 1f.5 on  end						# PCH SPI
+		device pci 1f.6 off end						# GbE
+		device pci 1f.7 off end						# TH
+	end
+end