1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/romcc_io.h>
#include "it8712f.h"
/* The base address is 0x2e or 0x4e, depending on config bytes. */
#define SIO_BASE 0x2e
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
/* Global configuration registers. */
#define IT8712F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8712F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8712F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
#define IT8712F_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */
#define IT8712F_CONFIG_REG_SWSUSP 0x24 /* Software Suspend, Flash I/F. */
#define IT8712F_CONFIG_REG_MFC 0x2a /* Multi-function control */
#define IT8712F_CONFIG_REG_WATCHDOG 0x72 /* Watchdog control. */
#define IT8712F_CONFIGURATION_PORT 0x2e /* Write-only. */
/* The content of IT8712F_CONFIG_REG_LDN (index 0x07) must be set to the
LDN the register belongs to, before you can access the register. */
static void it8712f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8712F_CONFIG_REG_LDN, SIO_BASE);
outb(ldn, SIO_DATA);
outb(index, SIO_BASE);
outb(value, SIO_DATA);
}
static void it8712f_enter_conf(void)
{
/* Enter the configuration state (MB PnP mode). */
/* Perform MB PnP setup to put the SIO chip at 0x2e. */
/* Base address 0x2e: 0x87 0x01 0x55 0x55. */
/* Base address 0x4e: 0x87 0x01 0x55 0xaa. */
outb(0x87, IT8712F_CONFIGURATION_PORT);
outb(0x01, IT8712F_CONFIGURATION_PORT);
outb(0x55, IT8712F_CONFIGURATION_PORT);
outb(0x55, IT8712F_CONFIGURATION_PORT);
}
static void it8712f_exit_conf(void)
{
/* Exit the configuration state (MB PnP mode). */
it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CC, 0x02);
}
static void it8712f_24mhz_clkin(void)
{
it8712f_enter_conf();
/* Select 24MHz CLKIN (48MHZ default)*/
it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CLOCKSEL, 0x1);
it8712f_exit_conf();
}
static void it8712f_enable_3vsbsw(void) {
/* We need to set enable 3VSBSW#, this was documented only in IT8712F_V0.9.2!
LDN 7, reg 0x2a - needed for S3, or memory power will be cut off.
Enable 3VSBSW#. (For System Suspend-to-RAM)
0: 3VSBSW# will be always inactive.
1: 3VSBSW# enabled. It will be (NOT SUSB#) NAND SUSC#.
*/
it8712f_enter_conf();
it8712f_sio_write(0x07, IT8712F_CONFIG_REG_MFC, 0x80);
it8712f_exit_conf();
}
static void it8712f_kill_watchdog(void)
{
it8712f_enter_conf();
/* Kill the Watchdog */
it8712f_sio_write(0x07, IT8712F_CONFIG_REG_WATCHDOG, 0x00);
it8712f_exit_conf();
}
/* Enable the peripheral devices on the IT8712F Super I/O chip. */
static void it8712f_enable_serial(device_t dev, unsigned iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
it8712f_enter_conf();
/* (2) Modify the data of configuration registers. */
/* Select the chip to configure (if there's more than one).
Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
If this register is not written, both chips are configured. */
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable serial port(s). */
it8712f_sio_write(IT8712F_SP1, 0x30, 0x1); /* Serial port 1 */
it8712f_sio_write(IT8712F_SP2, 0x30, 0x1); /* Serial port 2 */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
it8712f_exit_conf();
}
|
