1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/io.h>
#include "it8712f.h"
/* The base address is 0x2e or 0x4e, depending on config bytes. */
#define SIO_BASE 0x2e
#define SIO_INDEX SIO_BASE
#define SIO_DATA (SIO_BASE + 1)
/* Global configuration registers. */
#define IT8712F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8712F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8712F_CONFIG_REG_CONFIGSEL 0x22 /* Configuration Select. */
#define IT8712F_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */
#define IT8712F_CONFIG_REG_SWSUSP 0x24 /* Software Suspend, Flash I/F. */
#define IT8712F_CONFIG_REG_MFC 0x2a /* Multi-function control */
#define IT8712F_CONFIG_REG_WATCHDOG 0x72 /* Watchdog control. */
static void it8712f_sio_write(u8 ldn, u8 index, u8 value)
{
outb(IT8712F_CONFIG_REG_LDN, SIO_BASE);
outb(ldn, SIO_DATA);
outb(index, SIO_BASE);
outb(value, SIO_DATA);
}
static void it8712f_enter_conf(void)
{
u16 port = 0x2e; /* TODO: Don't hardcode! */
outb(0x87, port);
outb(0x01, port);
outb(0x55, port);
outb((port == 0x4e) ? 0xaa : 0x55, port);
}
static void it8712f_exit_conf(void)
{
it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CC, 0x02);
}
/* Select 24MHz CLKIN (48MHz is the default). */
void it8712f_24mhz_clkin(void)
{
it8712f_enter_conf();
it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CLOCKSEL, 0x1);
it8712f_exit_conf();
}
/*
* We need to set enable 3VSBSW#, this was documented only in IT8712F_V0.9.2!
*
* LDN 7, reg 0x2a - needed for S3, or memory power will be cut off.
*
* Enable 3VSBSW#. (For System Suspend-to-RAM)
* 0: 3VSBSW# will be always inactive.
* 1: 3VSBSW# enabled. It will be (NOT SUSB#) NAND SUSC#.
*/
void it8712f_enable_3vsbsw(void)
{
it8712f_enter_conf();
it8712f_sio_write(IT8712F_GPIO, IT8712F_CONFIG_REG_MFC, 0x80);
it8712f_exit_conf();
}
void it8712f_kill_watchdog(void)
{
it8712f_enter_conf();
it8712f_sio_write(IT8712F_GPIO, IT8712F_CONFIG_REG_WATCHDOG, 0x00);
it8712f_exit_conf();
}
/* Enable the serial port(s). */
void it8712f_enable_serial(device_t dev, u16 iobase)
{
/* (1) Enter the configuration state (MB PnP mode). */
it8712f_enter_conf();
/* (2) Modify the data of configuration registers. */
/*
* Select the chip to configure (if there's more than one).
* Set bit 7 to select JP3=1, clear bit 7 to select JP3=0.
* If this register is not written, both chips are configured.
*/
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_CONFIGSEL, 0x00); */
/* Enable serial port(s). */
it8712f_sio_write(IT8712F_SP1, 0x30, 0x1); /* Serial port 1 */
it8712f_sio_write(IT8712F_SP2, 0x30, 0x1); /* Serial port 2 */
/* Clear software suspend mode (clear bit 0). TODO: Needed? */
/* it8712f_sio_write(0x00, IT8712F_CONFIG_REG_SWSUSP, 0x00); */
/* (3) Exit the configuration state (MB PnP mode). */
it8712f_exit_conf();
}
|
