1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
/*
* This file is part of the LinuxBIOS project.
*
* Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/romcc_io.h>
#include "it8673f.h"
/* The base address is 0x3f0, 0x3bd, or 0x370, depending on config bytes. */
#define SIO_BASE 0x3f0
#define SIO_INDEX SIO_BASE
#define SIO_DATA SIO_BASE+1
/* Global configuration registers. */
#define IT8673F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8673F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8673F_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */
#define IT8673F_CONFIG_REG_SWSUSP 0x24 /* Software Suspend. */
#define IT8673F_CONFIGURATION_PORT 0x0279 /* Write-only. */
/* Special values used for entering MB PnP mode. The first four bytes of
each line determine the address port, the last four are data. */
static const uint8_t init_values[] = {
0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
0xb0, 0x58, 0x2c, 0x16, /**/ 0x8b, 0x45, 0xa2, 0xd1,
0xe8, 0x74, 0x3a, 0x9d, /**/ 0xce, 0xe7, 0x73, 0x39,
};
/* The content of IT8673F_CONFIG_REG_LDN (index 0x07) must be set to the
LDN the register belongs to, before you can access the register. */
static void it8673f_sio_write(uint8_t ldn, uint8_t index, uint8_t value)
{
outb(IT8673F_CONFIG_REG_LDN, SIO_BASE);
outb(ldn, SIO_DATA);
outb(index, SIO_BASE);
outb(value, SIO_DATA);
}
/* Enable the peripheral devices on the IT8673F Super I/O chip. */
static void it8673f_enable_serial(device_t dev, unsigned iobase)
{
uint8_t i;
/* (1) Enter the configuration state (MB PnP mode). */
/* Perform MB PnP setup to put the SIO chip at 0x3f0. */
/* Base address 0x3f0: 0x86 0x80 0x55 0x55. */
/* Base address 0x3bd: 0x86 0x80 0x55 0xaa. */
/* Base address 0x370: 0x86 0x80 0xaa 0x55. */
outb(0x86, IT8673F_CONFIGURATION_PORT);
outb(0x80, IT8673F_CONFIGURATION_PORT);
outb(0x55, IT8673F_CONFIGURATION_PORT);
outb(0x55, IT8673F_CONFIGURATION_PORT);
/* Sequentially write the 32 special values. */
for (i = 0; i < 32; i++) {
outb(init_values[i], SIO_BASE);
}
/* (2) Modify the data of configuration registers. */
/* Enable all devices. */
it8673f_sio_write(IT8673F_FDC, 0x30, 0x1); /* Floppy */
it8673f_sio_write(IT8673F_SP1, 0x30, 0x1); /* Serial port 1 */
it8673f_sio_write(IT8673F_SP2, 0x30, 0x1); /* Serial port 2 */
it8673f_sio_write(IT8673F_PP, 0x30, 0x1); /* Parallel port */
it8673f_sio_write(IT8673F_FAN, 0x30, 0x1); /* Fan controller */
it8673f_sio_write(IT8673F_KBCK, 0x30, 0x1); /* Keyboard */
it8673f_sio_write(IT8673F_KBCM, 0x30, 0x1); /* Mouse */
/* Select 24MHz CLKIN (clear bit 0). */
it8673f_sio_write(0x00, IT8673F_CONFIG_REG_CLOCKSEL, 0x00);
/* Clear software suspend mode (clear bit 0). */
it8673f_sio_write(0x00, IT8673F_CONFIG_REG_SWSUSP, 0x00);
/* (3) Exit the configuration state (MB PnP mode). */
it8673f_sio_write(0x00, IT8673F_CONFIG_REG_CC, 0x02);
}
|
