1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc.
*/
#include <arch/io.h>
#include <device/pnp.h>
#include <stdint.h>
#include "it8671f.h"
/* The base address is 0x3f0, 0x3bd, or 0x370, depending on config bytes. */
#define SIO_BASE 0x3f0
#define SIO_INDEX SIO_BASE
#define SIO_DATA (SIO_BASE + 1)
/* Global configuration registers. */
#define IT8671F_CONFIG_REG_CC 0x02 /* Configure Control (write-only). */
#define IT8671F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */
#define IT8671F_CONFIG_REG_LDE 0x23 /* PnP Logical Device Enable. */
#define IT8671F_CONFIG_REG_SWSUSP 0x24 /* Software Suspend. */
#define IT8671F_CONFIGURATION_PORT 0x0279 /* Write-only. */
/*
* Special values used for entering MB PnP mode. The first four bytes of
* each line determine the address port, the last four are data.
*/
static const u8 init_values[] = {
0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe,
0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61,
0xb0, 0x58, 0x2c, 0x16, /**/ 0x8b, 0x45, 0xa2, 0xd1,
0xe8, 0x74, 0x3a, 0x9d, /**/ 0xce, 0xe7, 0x73, 0x39,
};
static void it8671f_sio_write(u8 ldn, u8 index, u8 value)
{
outb(IT8671F_CONFIG_REG_LDN, SIO_BASE);
outb(ldn, SIO_DATA);
outb(index, SIO_BASE);
outb(value, SIO_DATA);
}
/* Enter the configuration state (MB PnP mode). */
static void it8671f_enter_conf(void)
{
int i;
/* Perform MB PnP setup to put the SIO chip at 0x3f0. */
/* Base address 0x3f0: 0x86 0x80 0x55 0x55. */
/* Base address 0x3bd: 0x86 0x80 0x55 0xaa. */
/* Base address 0x370: 0x86 0x80 0xaa 0x55. */
outb(0x86, IT8671F_CONFIGURATION_PORT);
outb(0x80, IT8671F_CONFIGURATION_PORT);
outb(0x55, IT8671F_CONFIGURATION_PORT);
outb(0x55, IT8671F_CONFIGURATION_PORT);
/* Sequentially write the 32 special values. */
for (i = 0; i < 32; i++)
outb(init_values[i], SIO_BASE);
}
/* Exit the configuration state (MB PnP mode). */
static void it8671f_exit_conf(void)
{
it8671f_sio_write(0x00, IT8671F_CONFIG_REG_CC, 0x02);
}
/* Select 48MHz CLKIN (24MHz is the default). */
void it8671f_48mhz_clkin(void)
{
it8671f_enter_conf();
it8671f_sio_write(0x00, IT8671F_CONFIG_REG_SWSUSP, (1 << 6));
it8671f_exit_conf();
}
/* Enable the serial port(s). */
void it8671f_enable_serial(pnp_devfn_t dev, u16 iobase)
{
it8671f_enter_conf();
/*
* Allow all devices to be enabled. Bits: FDC (0), Com1 (1), Com2 (2),
* PP (3), Reserved (4), KBCK (5), KBCM (6), Reserved (7).
*/
it8671f_sio_write(0x00, IT8671F_CONFIG_REG_LDE, 0x6f);
/* Enable serial port(s). */
it8671f_sio_write(IT8671F_SP1, 0x30, 0x01); /* Serial port 1 */
it8671f_sio_write(IT8671F_SP2, 0x30, 0x01); /* Serial port 2 */
it8671f_exit_conf();
}
|
