1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
/* SPDX-License-Identifier: GPL-2.0-or-later */
#ifndef SUPERIO_ITE_ENV_CTRL_CHIP_H
#define SUPERIO_ITE_ENV_CTRL_CHIP_H
#define ITE_EC_TMPIN_CNT 3
#if CONFIG(SUPERIO_ITE_ENV_CTRL_5FANS)
#define ITE_EC_FAN_CNT 5
#else
#define ITE_EC_FAN_CNT 3
#endif
/* Supported thermal mode on TMPINx */
enum ite_ec_thermal_mode {
THERMAL_MODE_DISABLED = 0,
THERMAL_DIODE,
THERMAL_RESISTOR,
THERMAL_PECI,
};
struct ite_ec_thermal_config {
enum ite_ec_thermal_mode mode;
/* Offset is used for diode sensors and PECI */
u8 offset;
/* Limits */
u8 min;
u8 max;
};
/* Bit mask for voltage pins VINx */
enum ite_ec_voltage_pin {
VIN0 = 0x01,
VIN1 = 0x02,
VIN2 = 0x04,
VIN3 = 0x08,
VIN4 = 0x10,
VIN5 = 0x20,
VIN6 = 0x40,
VIN7 = 0x80,
VIN_ALL = 0xff
};
enum ite_ec_fan_mode {
FAN_IGNORE = 0,
FAN_MODE_ON,
FAN_MODE_OFF,
FAN_SMART_SOFTWARE,
FAN_SMART_AUTOMATIC,
};
struct ite_ec_fan_smartconfig {
u8 tmpin; /* select TMPINx (1, 2 or 3) */
u8 tmp_off; /* turn fan off below (°C) */
u8 tmp_start; /* turn fan on above (°C) */
u8 tmp_full; /* 100% duty cycle above (°C) */
u8 tmp_delta; /* adapt fan speed when temperature changed by
at least `tmp_delta`°C */
u8 full_lmt; /* force fan to full PWM at thermal limit */
u8 smoothing; /* enable smoothing */
u8 pwm_start; /* start at this duty cycle (%) */
u8 slope; /* increase duty cycle by `slope`%/°C */
u8 clsd_loop; /* tachometer closed-loop mode enable */
u16 rpm_start; /* start at this RPM (clsd_loop = 1) */
};
struct ite_ec_fan_config {
enum ite_ec_fan_mode mode;
struct ite_ec_fan_smartconfig smart;
};
struct ite_ec_config {
/*
* Enable reading of voltage pins VINx.
*/
enum ite_ec_voltage_pin vin_mask;
/*
* Enable temperature sensors in given mode.
*/
struct ite_ec_thermal_config tmpin[ITE_EC_TMPIN_CNT];
/*
* Enable a FAN in given mode.
*/
struct ite_ec_fan_config fan[ITE_EC_FAN_CNT];
bool tmpin_beep;
bool fan_beep;
bool vin_beep;
/*
* Enable SMBus for external thermal sensor.
*/
bool smbus_en;
/*
* Select 24 MHz clock for external host instead of an
* internally generated 32 MHz clock.
*/
bool smbus_24mhz;
};
/* Some shorthands for device trees */
#define TMPIN1 ec.tmpin[0]
#define TMPIN2 ec.tmpin[1]
#define TMPIN3 ec.tmpin[2]
#define FAN1 ec.fan[0]
#define FAN2 ec.fan[1]
#define FAN3 ec.fan[2]
#define FAN4 ec.fan[3]
#define FAN5 ec.fan[4]
#endif /* SUPERIO_ITE_ENV_CTRL_CHIP_H */
|
