1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
|
/* SPDX-License-Identifier: GPL-2.0-or-later */
#include <console/console.h>
#include <delay.h>
#include <stddef.h>
#include <superio/hwm5_conf.h>
#include "env_ctrl.h"
#include "env_ctrl_chip.h"
static void extemp_force_idle_status(const u16 base)
{
u8 reg;
int retries = 10;
/* Wait up to 10ms for non-busy state. */
while (retries > 0) {
reg = pnp_read_hwm5_index(base, ITE_EC_EXTEMP_STATUS);
if ((reg & ITE_EC_EXTEMP_STATUS_HOST_BUSY) == 0x0)
break;
retries--;
mdelay(1);
}
if (retries == 0 && (reg & ITE_EC_EXTEMP_STATUS_HOST_BUSY) == 0x1) {
/*
* SIO is busy due to unfinished peci transaction.
* Re-configure Register 0x8E to terminate processes.
*/
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_CONTROL,
ITE_EC_EXTEMP_CTRL_AUTO_4HZ | ITE_EC_EXTEMP_CTRL_AUTO_START);
}
}
/*
* Setup PECI interface
*/
static void enable_peci(const u16 base)
{
/* Enable PECI interface */
pnp_write_hwm5_index(base, ITE_EC_INTERFACE_SELECT,
ITE_EC_INTERFACE_SEL_PECI | ITE_EC_INTERFACE_SPEED_TOLERANCE);
/* Setup External Temperature using PECI GetTemp */
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_ADDRESS, PECI_CLIENT_ADDRESS);
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_COMMAND, PECI_GETTEMP_COMMAND);
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_WRITE_LENGTH, PECI_GETTEMP_WRITE_LENGTH);
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_READ_LENGTH, PECI_GETTEMP_READ_LENGTH);
pnp_write_hwm5_index(base, ITE_EC_EXTEMP_CONTROL,
ITE_EC_EXTEMP_CTRL_AUTO_4HZ | ITE_EC_EXTEMP_CTRL_AUTO_START);
}
/*
* Set up External Temperature to read via PECI or thermal diode/resistor
* into TMPINx register
*/
static void enable_tmpin(const u16 base, const u8 tmpin,
const struct ite_ec_thermal_config *const conf)
{
u8 reg;
reg = pnp_read_hwm5_index(base, ITE_EC_ADC_TEMP_CHANNEL_ENABLE);
switch (conf->mode) {
case THERMAL_PECI:
if (reg & ITE_EC_ADC_TEMP_EXT_REPORTS_TO_MASK) {
printk(BIOS_WARNING, "PECI specified for multiple TMPIN\n");
return;
}
enable_peci(base);
reg |= ITE_EC_ADC_TEMP_EXT_REPORTS_TO(tmpin);
break;
case THERMAL_DIODE:
reg |= ITE_EC_ADC_TEMP_DIODE_MODE(tmpin);
break;
case THERMAL_RESISTOR:
reg |= ITE_EC_ADC_TEMP_RESISTOR_MODE(tmpin);
break;
default:
printk(BIOS_WARNING, "Unsupported thermal mode 0x%x on TMPIN%d\n",
conf->mode, tmpin);
return;
}
pnp_write_hwm5_index(base, ITE_EC_ADC_TEMP_CHANNEL_ENABLE, reg);
/* Set temperature offsets */
if (conf->mode != THERMAL_RESISTOR) {
reg = pnp_read_hwm5_index(base, ITE_EC_BEEP_ENABLE);
reg |= ITE_EC_TEMP_ADJUST_WRITE_ENABLE;
pnp_write_hwm5_index(base, ITE_EC_BEEP_ENABLE, reg);
pnp_write_hwm5_index(base, ITE_EC_TEMP_ADJUST[tmpin-1], conf->offset);
}
/* Set temperature limits */
u8 max = conf->max;
pnp_write_hwm5_index(base, ITE_EC_HIGH_TEMP_LIMIT(tmpin), max ? max : 127);
pnp_write_hwm5_index(base, ITE_EC_LOW_TEMP_LIMIT(tmpin), conf->min);
/* Enable the startup of monitoring operation */
reg = pnp_read_hwm5_index(base, ITE_EC_CONFIGURATION);
reg |= ITE_EC_CONFIGURATION_START;
pnp_write_hwm5_index(base, ITE_EC_CONFIGURATION, reg);
}
static void fan_smartconfig(const u16 base, const u8 fan,
const enum ite_ec_fan_mode mode,
const struct ite_ec_fan_smartconfig *const conf)
{
u8 pwm_ctrl;
u8 pwm_start = 0;
u8 pwm_auto = 0;
if (mode == FAN_SMART_SOFTWARE) {
pwm_ctrl = ITE_EC_FAN_CTL_PWM_MODE_SOFTWARE;
/* 50% duty cycle by default */
const u8 duty = conf->pwm_start ? conf->pwm_start : 50;
if (CONFIG(SUPERIO_ITE_ENV_CTRL_8BIT_PWM))
pwm_start = ITE_EC_FAN_CTL_PWM_DUTY(duty);
else
pwm_ctrl |= ITE_EC_FAN_CTL_PWM_DUTY(duty);
} else {
pwm_ctrl = ITE_EC_FAN_CTL_PWM_MODE_AUTOMATIC;
pwm_ctrl |= ITE_EC_FAN_CTL_TEMPIN(conf->tmpin);
pwm_start = ITE_EC_FAN_CTL_PWM_START_DUTY(conf->pwm_start);
if (CONFIG(SUPERIO_ITE_ENV_CTRL_7BIT_SLOPE_REG)) {
pwm_auto = conf->slope & 0x7f;
} else {
pwm_start |= ITE_EC_FAN_CTL_PWM_SLOPE_BIT6(conf->slope);
pwm_auto = ITE_EC_FAN_CTL_PWM_SLOPE_LOWER(conf->slope);
}
if (conf->smoothing)
pwm_auto |= ITE_EC_FAN_CTL_AUTO_SMOOTHING_EN;
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_TEMP_LIMIT_OFF(fan), conf->tmp_off);
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_TEMP_LIMIT_START(fan),
conf->tmp_start);
/* Full speed above 127°C by default */
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_TEMP_LIMIT_FULL(fan),
conf->tmp_full ? conf->tmp_full : 127);
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_DELTA_TEMP(fan),
ITE_EC_FAN_CTL_DELTA_TEMP_INTRVL(conf->tmp_delta));
}
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_PWM_CONTROL(fan), pwm_ctrl);
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_PWM_START(fan), pwm_start);
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_PWM_AUTO(fan), pwm_auto);
}
static void enable_fan(const u16 base, const u8 fan,
const struct ite_ec_fan_config *const conf)
{
u8 reg;
if (conf->mode == FAN_IGNORE ||
(CONFIG(SUPERIO_ITE_ENV_CTRL_NO_ONOFF) &&
conf->mode <= FAN_MODE_OFF))
return;
/* FAN_CTL2 might have its own frequency setting */
if (CONFIG(SUPERIO_ITE_ENV_CTRL_PWM_FREQ2) && fan == 2) {
reg = pnp_read_hwm5_index(base, ITE_EC_ADC_TEMP_EXTRA_CHANNEL_ENABLE);
reg &= ~ITE_EC_FAN_PWM_CLOCK_MASK;
reg |= ITE_EC_FAN_PWM_DEFAULT_CLOCK;
pnp_write_hwm5_index(base, ITE_EC_ADC_TEMP_EXTRA_CHANNEL_ENABLE, reg);
}
if (conf->mode >= FAN_SMART_SOFTWARE) {
fan_smartconfig(base, fan, conf->mode, &conf->smart);
} else {
reg = pnp_read_hwm5_index(base, ITE_EC_FAN_CTL_MODE);
if (conf->mode == FAN_MODE_ON)
reg |= ITE_EC_FAN_CTL_ON(fan);
else
reg &= ~ITE_EC_FAN_CTL_ON(fan);
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_MODE, reg);
}
if (CONFIG(SUPERIO_ITE_ENV_CTRL_FAN16_CONFIG) && conf->mode >= FAN_MODE_ON) {
reg = pnp_read_hwm5_index(base, ITE_EC_FAN_TAC_COUNTER_ENABLE);
reg |= ITE_EC_FAN_TAC_16BIT_ENABLE(fan);
pnp_write_hwm5_index(base, ITE_EC_FAN_TAC_COUNTER_ENABLE, reg);
}
if (CONFIG(SUPERIO_ITE_ENV_CTRL_5FANS) && fan > 3) {
reg = pnp_read_hwm5_index(base, ITE_EC_FAN_SEC_CTL);
if (conf->mode >= FAN_MODE_ON)
reg |= ITE_EC_FAN_SEC_CTL_TAC_EN(fan);
else
reg &= ~ITE_EC_FAN_SEC_CTL_TAC_EN(fan);
pnp_write_hwm5_index(base, ITE_EC_FAN_SEC_CTL, reg);
} else {
reg = pnp_read_hwm5_index(base, ITE_EC_FAN_MAIN_CTL);
if (conf->mode >= FAN_MODE_ON)
reg |= ITE_EC_FAN_MAIN_CTL_TAC_EN(fan);
else
reg &= ~ITE_EC_FAN_MAIN_CTL_TAC_EN(fan);
/* Some ITEs have SmartGuardian always enabled */
if (!CONFIG(SUPERIO_ITE_ENV_CTRL_NO_ONOFF)) {
if (conf->mode >= FAN_SMART_SOFTWARE)
reg |= ITE_EC_FAN_MAIN_CTL_SMART(fan);
else
reg &= ~ITE_EC_FAN_MAIN_CTL_SMART(fan);
}
pnp_write_hwm5_index(base, ITE_EC_FAN_MAIN_CTL, reg);
}
}
static void enable_beeps(const u16 base, const struct ite_ec_config *const conf)
{
u8 reg = 0;
u8 freq = ITE_EC_BEEP_TONE_DIVISOR(10) | ITE_EC_BEEP_FREQ_DIVISOR(10);
if (conf->tmpin_beep) {
reg |= ITE_EC_BEEP_ON_TMP_LIMIT;
pnp_write_hwm5_index(base, ITE_EC_BEEP_FREQ_DIV_OF_TMPIN, freq);
}
if (conf->fan_beep) {
reg |= ITE_EC_BEEP_ON_FAN_LIMIT;
pnp_write_hwm5_index(base, ITE_EC_BEEP_FREQ_DIV_OF_FAN, freq);
}
if (conf->vin_beep) {
reg |= ITE_EC_BEEP_ON_VIN_LIMIT;
pnp_write_hwm5_index(base, ITE_EC_BEEP_FREQ_DIV_OF_VIN, freq);
}
if (reg) {
reg |= pnp_read_hwm5_index(base, ITE_EC_BEEP_ENABLE);
pnp_write_hwm5_index(base, ITE_EC_BEEP_ENABLE, reg);
}
}
void ite_ec_init(const u16 base, const struct ite_ec_config *const conf)
{
size_t i;
/* Configure 23.43kHz PWM active high output */
u8 fan_ctl = pnp_read_hwm5_index(base, ITE_EC_FAN_CTL_MODE);
fan_ctl &= ~ITE_EC_FAN_PWM_CLOCK_MASK;
fan_ctl |= ITE_EC_FAN_PWM_DEFAULT_CLOCK;
fan_ctl |= ITE_EC_FAN_CTL_POLARITY_HIGH;
pnp_write_hwm5_index(base, ITE_EC_FAN_CTL_MODE, fan_ctl);
/* Enable HWM if configured */
for (i = 0; i < ITE_EC_TMPIN_CNT; ++i)
enable_tmpin(base, i + 1, &conf->tmpin[i]);
/* Enable External Sensor SMBus Host if configured */
if (conf->smbus_en) {
pnp_write_hwm5_index(base, ITE_EC_INTERFACE_SELECT,
pnp_read_hwm5_index(base, ITE_EC_INTERFACE_SELECT) |
ITE_EC_INTERFACE_SMB_ENABLE);
}
/* Enable reading of voltage pins */
pnp_write_hwm5_index(base, ITE_EC_ADC_VOLTAGE_CHANNEL_ENABLE, conf->vin_mask);
/* Enable FANx if configured */
for (i = 0; i < ITE_EC_FAN_CNT; ++i)
enable_fan(base, i + 1, &conf->fan[i]);
/* Enable beeps if configured */
enable_beeps(base, conf);
/*
* System may get wrong temperature data when SIO is in
* busy state. Therefore, check the status and terminate
* processes if needed.
*/
for (i = 0; i < ITE_EC_TMPIN_CNT; ++i)
if (conf->tmpin[i].mode == THERMAL_PECI)
extemp_force_idle_status(base);
}
|
