1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
|
#include <console/console.h>
#include <device/device.h>
#include <device/pci.h>
#include <device/pci_ops.h>
#include <device/pci_ids.h>
#include <pc80/mc146818rtc.h>
#include <arch/ioapic.h>
#include "chip.h"
/* PIRQ init
*/
static const unsigned char southbridgeIrqs[4] = { 11, 5, 10, 12 };
static const unsigned char enetIrqs[4] = { 11, 5, 10, 12 };
static const unsigned char slotIrqs[4] = { 5, 10, 12, 11 };
/*
Our IDSEL mappings are as follows
PCI slot is AD31 (device 15) (00:14.0)
Southbridge is AD28 (device 12) (00:11.0)
*/
static void pci_routing_fixup(struct device *dev)
{
printk(BIOS_INFO, "%s: dev is %p\n", __func__, dev);
if (dev) {
/* initialize PCI interupts - these assignments depend
on the PCB routing of PINTA-D
PINTA = IRQ11
PINTB = IRQ5
PINTC = IRQ10
PINTD = IRQ12
*/
pci_write_config8(dev, 0x55, 0xb0);
pci_write_config8(dev, 0x56, 0xa5);
pci_write_config8(dev, 0x57, 0xc0);
}
// Standard southbridge components
printk(BIOS_INFO, "setting southbridge\n");
pci_assign_irqs(0, 0x11, southbridgeIrqs);
// Ethernet built into southbridge
printk(BIOS_INFO, "setting ethernet\n");
pci_assign_irqs(0, 0x12, enetIrqs);
// PCI slot
printk(BIOS_INFO, "setting pci slot\n");
pci_assign_irqs(0, 0x14, slotIrqs);
printk(BIOS_INFO, "%s: DONE\n", __func__);
}
static void vt8231_init(struct device *dev)
{
unsigned char enables;
printk(BIOS_DEBUG, "vt8231 init\n");
// enable the internal I/O decode
enables = pci_read_config8(dev, 0x6C);
enables |= 0x80;
pci_write_config8(dev, 0x6C, enables);
// Set bit 6 of 0x40, because Award does it (IO recovery time)
// IMPORTANT FIX - EISA 0x4d0 decoding must be on so that PCI
// interrupts can be properly marked as level triggered.
enables = pci_read_config8(dev, 0x40);
pci_write_config8(dev, 0x40, enables);
// Set 0x42 to 0xf0 to match Award bios
enables = pci_read_config8(dev, 0x42);
enables |= 0xf0;
pci_write_config8(dev, 0x42, enables);
// Set bit 3 of 0x4a, to match award (dummy pci request)
enables = pci_read_config8(dev, 0x4a);
enables |= 0x08;
pci_write_config8(dev, 0x4a, enables);
// Set bit 3 of 0x4f to match award (use INIT# as cpu reset)
enables = pci_read_config8(dev, 0x4f);
enables |= 0x08;
pci_write_config8(dev, 0x4f, enables);
// Set 0x58 to 0x03 to match Award
pci_write_config8(dev, 0x58, 0x03);
// enable the ethernet/RTC
if (dev) {
enables = pci_read_config8(dev, 0x51);
enables |= 0x18;
pci_write_config8(dev, 0x51, enables);
}
// enable IDE, since Linux won't do it.
// First do some more things to devfn (17,0)
// note: this should already be cleared, according to the book.
enables = pci_read_config8(dev, 0x50);
printk(BIOS_DEBUG, "IDE enable in reg. 50 is 0x%x\n", enables);
enables &= ~8; // need manifest constant here!
printk(BIOS_DEBUG, "set IDE reg. 50 to 0x%x\n", enables);
pci_write_config8(dev, 0x50, enables);
// set default interrupt values (IDE)
enables = pci_read_config8(dev, 0x4c);
printk(BIOS_DEBUG, "IRQs in reg. 4c are 0x%x\n", enables & 0xf);
// clear out whatever was there.
enables &= ~0xf;
enables |= 4;
printk(BIOS_DEBUG, "setting reg. 4c to 0x%x\n", enables);
pci_write_config8(dev, 0x4c, enables);
// set up the serial port interrupts.
// com2 to 3, com1 to 4
pci_write_config8(dev, 0x46, 0x04);
pci_write_config8(dev, 0x47, 0x03);
pci_write_config8(dev, 0x6e, 0x98);
/* set up isa bus -- i/o recovery time, rom write enable, extend-ale */
pci_write_config8(dev, 0x40, 0x54);
//ethernet_fixup();
// Start the rtc
rtc_init(0);
}
static void vt8231_read_resources(device_t dev)
{
struct resource *res;
pci_dev_read_resources(dev);
res = new_resource(dev, 1);
res->base = 0x0UL;
res->size = 0x1000UL;
res->limit = 0xffffUL;
res->flags = IORESOURCE_IO | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
res = new_resource(dev, 3); /* IOAPIC */
res->base = IO_APIC_ADDR;
res->size = 0x00001000;
res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
}
static void southbridge_init(struct device *dev)
{
vt8231_init(dev);
pci_routing_fixup(dev);
}
static struct device_operations vt8231_lpc_ops = {
.read_resources = vt8231_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
.init = &southbridge_init,
.scan_bus = scan_static_bus,
.enable = 0,
.ops_pci = 0,
};
static const struct pci_driver lpc_driver __pci_driver = {
.ops = &vt8231_lpc_ops,
.vendor = PCI_VENDOR_ID_VIA,
.device = PCI_DEVICE_ID_VIA_8231,
};
|
