1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
#include "smbus.h"
#define SMBUS_IO_BASE 0x0f00
static void enable_smbus(void)
{
device_t dev = PCI_DEV(0x0, 0x1f, 0x3);
printk(BIOS_SPEW, "SMBus controller enabled\n");
pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1);
printk(BIOS_DEBUG, "%08x", pci_read_config32(dev, 0x20));
/* Set smbus enable */
pci_write_config8(dev, 0x40, 1);
/* Set smbus iospace enable */
pci_write_config8(dev, 0x4, 1);
/* SMBALERT_DIS */
pci_write_config8(dev, 0x11, 4);
/* Disable interrupt generation */
outb(0, SMBUS_IO_BASE + SMBHSTCTL);
/* clear any lingering errors, so the transaction will run */
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
}
static int smbus_read_byte(unsigned device, unsigned address)
{
return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
}
#ifdef UNUSED_CODE
static void smbus_write_byte(unsigned device, unsigned address, unsigned char val)
{
if (smbus_wait_until_ready(SMBUS_IO_BASE) < 0) {
return;
}
printk(BIOS_DEBUG, "Unimplemented smbus_write_byte() called.\n");
#if 0
/* setup transaction */
/* disable interrupts */
outw(inw(SMBUS_IO_BASE + SMBGCTL) & ~((1<<10)|(1<<9)|(1<<8)|(1<<4)),
SMBUS_IO_BASE + SMBGCTL);
/* set the device I'm talking too */
outw(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBHSTADDR);
outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
/* set up for a byte data write */ /* FIXME */
outw((inw(SMBUS_IO_BASE + SMBGCTL) & ~7) | (0x1), SMBUS_IO_BASE + SMBGCTL);
/* clear any lingering errors, so the transaction will run */
/* Do I need to write the bits to a 1 to clear an error? */
outw(inw(SMBUS_IO_BASE + SMBGSTATUS), SMBUS_IO_BASE + SMBGSTATUS);
/* clear the data word...*/
outw(val, SMBUS_IO_BASE + SMBHSTDAT);
/* start the command */
outw((inw(SMBUS_IO_BASE + SMBGCTL) | (1 << 3)), SMBUS_IO_BASE + SMBGCTL);
/* poll for transaction completion */
smbus_wait_until_done(SMBUS_IO_BASE);
#endif
return;
}
static int smbus_write_block(unsigned device, unsigned length, unsigned cmd,
unsigned data1, unsigned data2)
{
unsigned char byte;
unsigned char stat;
int i;
/* chear the PM timeout flags, SECOND_TO_STS */
outw(inw(0x0400 + 0x66), 0x0400 + 0x66);
if (smbus_wait_until_ready(SMBUS_IO_BASE) < 0) {
return -2;
}
/* setup transaction */
/* Obtain ownership */
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
for(stat=0;(stat&0x40)==0;) {
stat = inb(SMBUS_IO_BASE + SMBHSTSTAT);
}
/* clear the done bit */
outb(0x80, SMBUS_IO_BASE + SMBHSTSTAT);
/* disable interrupts */
outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL);
/* set the device I'm talking too */
outb(((device & 0x7f) << 1), SMBUS_IO_BASE + SMBXMITADD);
/* set the command address */
outb(cmd & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
/* set the block length */
outb(length & 0xFF, SMBUS_IO_BASE + SMBHSTDAT0);
/* try sending out the first byte of data here */
byte=(data1>>(0))&0x0ff;
outb(byte,SMBUS_IO_BASE + SMBBLKDAT);
/* issue a block write command */
outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x5 << 2) | 0x40,
SMBUS_IO_BASE + SMBHSTCTL);
for(i=0;i<length;i++) {
/* poll for transaction completion */
if (smbus_wait_until_blk_done(SMBUS_IO_BASE) < 0) {
return -3;
}
/* load the next byte */
if(i>3)
byte=(data2>>(i%4))&0x0ff;
else
byte=(data1>>(i))&0x0ff;
outb(byte,SMBUS_IO_BASE + SMBBLKDAT);
/* clear the done bit */
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT),
SMBUS_IO_BASE + SMBHSTSTAT);
}
printk(BIOS_DEBUG, "SMBUS Block complete\n");
return 0;
}
#endif
|
