1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
|
//#define SMBUS_IO_BASE 0x1000
#define SMBUS_IO_BASE 0x0f00
#define SMBHSTSTAT 0x0
#define SMBHSTCTL 0x2
#define SMBHSTCMD 0x3
#define SMBXMITADD 0x4
#define SMBHSTDAT0 0x5
#define SMBHSTDAT1 0x6
#define SMBBLKDAT 0x7
#define SMBTRNSADD 0x9
#define SMBSLVDATA 0xa
#define SMLINK_PIN_CTL 0xe
#define SMBUS_PIN_CTL 0xf
/* Between 1-10 seconds, We should never timeout normally
* Longer than this is just painful when a timeout condition occurs.
*/
#define SMBUS_TIMEOUT (100*1000*10)
static void enable_smbus(void)
{
device_t dev = PCI_DEV(0x0, 0x1f, 0x3);
print_debug("SMBus controller enabled\r\n");
/* set smbus iobase */
pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1);
/* Set smbus enable */
pci_write_config8(dev, 0x40, 0x01);
/* Set smbus iospace enable */
pci_write_config16(dev, 0x4, 0x01);
/* Disable interrupt generation */
outb(0, SMBUS_IO_BASE + SMBHSTCTL);
/* clear any lingering errors, so the transaction will run */
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
}
static inline void smbus_delay(void)
{
outb(0x80, 0x80);
}
static int smbus_wait_until_active(void)
{
unsigned long loops;
loops = SMBUS_TIMEOUT;
do {
unsigned char val;
smbus_delay();
val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
if ((val & 1)) {
break;
}
} while(--loops);
return loops?0:-4;
}
static int smbus_wait_until_ready(void)
{
unsigned long loops;
loops = SMBUS_TIMEOUT;
do {
unsigned char val;
smbus_delay();
val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
if ((val & 1) == 0) {
break;
}
if(loops == (SMBUS_TIMEOUT / 2)) {
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT),
SMBUS_IO_BASE + SMBHSTSTAT);
}
} while(--loops);
return loops?0:-2;
}
static int smbus_wait_until_done(void)
{
unsigned long loops;
loops = SMBUS_TIMEOUT;
do {
unsigned char val;
smbus_delay();
val = inb(SMBUS_IO_BASE + SMBHSTSTAT);
if ( (val & 1) == 0) {
break;
}
if ((val & ~((1<<6)|(1<<0)) ) != 0 ) {
break;
}
} while(--loops);
return loops?0:-3;
}
static int smbus_read_byte(unsigned device, unsigned address)
{
unsigned char global_control_register;
unsigned char global_status_register;
unsigned char byte;
/*print_err("smbus_read_byte\r\n");*/
if (smbus_wait_until_ready() < 0) {
print_err_hex8(-2);
return -2;
}
/* setup transaction */
/* disable interrupts */
outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL);
/* set the device I'm talking too */
outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD);
/* set the command/address... */
outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
/* set up for a byte data read */
outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2<<2), SMBUS_IO_BASE + SMBHSTCTL);
/* clear any lingering errors, so the transaction will run */
outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
/* clear the data byte...*/
outb(0, SMBUS_IO_BASE + SMBHSTDAT0);
/* start a byte read, with interrupts disabled */
outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL);
/* poll for it to start */
if (smbus_wait_until_active() < 0) {
print_err_hex8(-4);
return -4;
}
/* poll for transaction completion */
if (smbus_wait_until_done() < 0) {
print_err_hex8(-3);
return -3;
}
global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~(1<<6); /* Ignore the In Use Status... */
/* read results of transaction */
byte = inb(SMBUS_IO_BASE + SMBHSTDAT0);
if (global_status_register != 2) {
print_err_hex8(-1);
return -1;
}
/*
print_err("smbus_read_byte: ");
print_err_hex32(device); print_err(" ad "); print_err_hex32(address);
print_err("value "); print_err_hex8(byte); print_err("\r\n");
*/
return byte;
}
#if 0
static void smbus_write_byte(unsigned device, unsigned address, unsigned char val)
{
if (smbus_wait_until_ready() < 0) {
return;
}
/* by LYH */
outb(0x37,SMBUS_IO_BASE + SMBHSTSTAT);
/* set the device I'm talking too */
outw(((device & 0x7f) << 1) | 0, SMBUS_IO_BASE + SMBHSTADDR);
/* data to send */
outb(val, SMBUS_IO_BASE + SMBHSTDAT);
outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD);
/* start the command */
outb(0xa, SMBUS_IO_BASE + SMBHSTCTL);
/* poll for transaction completion */
smbus_wait_until_done();
return;
}
#endif
|
