1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
|
/*
* (C) 2003 Linux Networx, SuSE Linux AG
* (C) 2004 Tyan Computer
* (c) 2005 Digital Design Corporation
*/
#include <console/console.h>
#include <device/device.h>
#include <device/pci.h>
#include <device/pci_ids.h>
#include <device/pci_ops.h>
#include <pc80/mc146818rtc.h>
#include <pc80/isa-dma.h>
#include <arch/io.h>
#include "i82801ca.h"
#define NMI_OFF 0
#ifndef MAINBOARD_POWER_ON_AFTER_POWER_FAIL
#define MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif
#define MAINBOARD_POWER_OFF 0
#define MAINBOARD_POWER_ON 1
void i82801ca_enable_ioapic( struct device *dev)
{
uint32_t dword;
volatile uint32_t* ioapic_index = (volatile uint32_t*)0xfec00000;
volatile uint32_t* ioapic_data = (volatile uint32_t*)0xfec00010;
dword = pci_read_config32(dev, GEN_CNTL);
dword |= (3 << 7); /* enable ioapic & disable SMBus interrupts */
dword |= (1 <<13); /* coprocessor error enable */
dword |= (1 << 1); /* delay transaction enable */
dword |= (1 << 2); /* DMA collection buf enable */
pci_write_config32(dev, GEN_CNTL, dword);
printk_debug("ioapic southbridge enabled %x\n",dword);
// Must program the APIC's ID before using it
*ioapic_index = 0; // Select APIC ID register
*ioapic_data = (2<<24);
// Hang if the ID didn't take (chip not present?)
*ioapic_index = 0;
dword = *ioapic_data;
printk_debug("Southbridge apic id = %x\n", (dword>>24) & 0xF);
if(dword != (2<<24))
die("");
*ioapic_index = 3; // Select Boot Configuration register
*ioapic_data = 1; // Use Processor System Bus to deliver interrupts
}
// This is how interrupts are received from the Super I/O chip
void i82801ca_enable_serial_irqs( struct device *dev)
{
// Recognize serial IRQs, continuous mode, frame size 21, 4 clock start frame pulse width
pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0<< 0));
}
//----------------------------------------------------------------------------------
// Function: i82801ca_lpc_route_dma
// Parameters: dev
// mask - identifies whether each channel should be used for PCI DMA
// (bit = 0) or LPC DMA (bit = 1). The LSb controls channel 0.
// Channel 4 is not used (reserved).
// Return Value: None
// Description: Route all DMA channels to either PCI or LPC.
//
void i82801ca_lpc_route_dma( struct device *dev, uint8_t mask)
{
uint16_t dmaConfig;
int channelIndex;
dmaConfig = pci_read_config16(dev, PCI_DMA_CFG);
dmaConfig &= 0x300; // Preserve reserved bits
for(channelIndex = 0; channelIndex < 8; channelIndex++) {
if (channelIndex == 4)
continue; // Register doesn't support channel 4
dmaConfig |= ((mask & (1 << channelIndex))? 3:1) << (channelIndex*2);
}
pci_write_config16(dev, PCI_DMA_CFG, dmaConfig);
}
void i82801ca_rtc_init(struct device *dev)
{
uint32_t dword;
int rtc_failed;
int pwr_on = MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
uint8_t pmcon3 = pci_read_config8(dev, GEN_PMCON_3);
rtc_failed = pmcon3 & RTC_BATTERY_DEAD;
if (rtc_failed) {
// Clear the RTC_BATTERY_DEAD bit, but preserve
// the RTC_POWER_FAILED, G3 state, and reserved bits
// NOTE: RTC_BATTERY_DEAD and RTC_POWER_FAILED are "write-1-clear" bits
pmcon3 &= ~RTC_POWER_FAILED;
}
get_option(&pwr_on, "power_on_after_fail");
pmcon3 &= ~SLEEP_AFTER_POWER_FAIL;
if (!pwr_on) {
pmcon3 |= SLEEP_AFTER_POWER_FAIL;
}
pci_write_config8(dev, GEN_PMCON_3, pmcon3);
printk_info("set power %s after power fail\n",
pwr_on ? "on" : "off");
// See if the Safe Mode jumper is set
dword = pci_read_config32(dev, GEN_STS);
rtc_failed |= dword & (1 << 2);
rtc_init(rtc_failed);
}
void i82801ca_1f0_misc(struct device *dev)
{
// Prevent LPC disabling, enable parity errors, and SERR# (System Error)
pci_write_config16(dev, PCI_COMMAND, 0x014f);
// Set ACPI base address to 0x1000 (I/O space)
pci_write_config32(dev, PMBASE, 0x00001001);
// Enable ACPI I/O and power management
pci_write_config8(dev, ACPI_CNTL, 0x10);
// Set GPIO base address to 0x1180 (I/O space)
pci_write_config32(dev, GPIO_BASE, 0x00001181);
// Enable GPIO
pci_write_config8(dev, GPIO_CNTL, 0x10);
// Route PIRQA to IRQ11, PIRQB to IRQ3, PIRQC to IRQ5, PIRQD to IRQ10
pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B);
// Route PIRQE to IRQ7. Leave PIRQF - PIRQH unrouted.
pci_write_config8(dev, PIRQE_ROUT, 0x07);
// Enable access to the upper 128 byte bank of CMOS RAM
pci_write_config8(dev, RTC_CONF, 0x04);
// Decode 0x3F8-0x3FF (COM1) for COMA port,
// 0x2F8-0x2FF (COM2) for COMB
pci_write_config8(dev, COM_DEC, 0x10);
// LPT decode defaults to 0x378-0x37F and 0x778-0x77F
// Floppy decode defaults to 0x3F0-0x3F5, 0x3F7
// Enable COMA, COMB, LPT, floppy;
// disable microcontroller, Super I/O, sound, gameport
pci_write_config16(dev, LPC_EN, 0x000F);
}
static void lpc_init(struct device *dev)
{
uint8_t byte;
int pwr_on=-1;
int nmi_option;
/* IO APIC initialization */
i82801ca_enable_ioapic(dev);
i82801ca_enable_serial_irqs(dev);
/* power after power fail */
/* FIXME this doesn't work! */
/* Which state do we want to goto after g3 (power restored)?
* 0 == S0 Full On
* 1 == S5 Soft Off
*/
byte = pci_read_config8(dev, GEN_PMCON_3);
if (pwr_on)
byte &= ~1; // Return to S0 (boot) after power is re-applied
else
byte |= 1; // Return to S5
pci_write_config8(dev, GEN_PMCON_3, byte);
printk_info("set power %s after power fail\n", pwr_on?"on":"off");
/* Set up NMI on errors */
byte = inb(0x61);
byte &= ~(1 << 3); /* IOCHK# NMI Enable */
byte &= ~(1 << 2); /* PCI SERR# Enable */
outb(byte, 0x61);
byte = inb(0x70);
nmi_option = NMI_OFF;
get_option(&nmi_option, "nmi");
if (nmi_option) {
byte &= ~(1 << 7); /* set NMI */
outb(byte, 0x70);
}
/* Initialize the real time clock */
i82801ca_rtc_init(dev);
i82801ca_lpc_route_dma(dev, 0xff);
/* Initialize isa dma */
isa_dma_init();
i82801ca_1f0_misc(dev);
}
static void i82801ca_lpc_read_resources(device_t dev)
{
struct resource *res;
/* Get the normal pci resources of this device */
pci_dev_read_resources(dev);
/* Add an extra subtractive resource for both memory and I/O */
res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED;
}
static void i82801ca_lpc_enable_resources(device_t dev)
{
pci_dev_enable_resources(dev);
enable_childrens_resources(dev);
}
static struct device_operations lpc_ops = {
.read_resources = i82801ca_lpc_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = i82801ca_lpc_enable_resources,
.init = lpc_init,
.scan_bus = scan_static_bus,
.enable = 0,
};
static struct pci_driver lpc_driver __pci_driver = {
.ops = &lpc_ops,
.vendor = PCI_VENDOR_ID_INTEL,
.device = PCI_DEVICE_ID_INTEL_82801CA_LPC,
};
|
