path: root/src/southbridge/intel/fsp_i89xx/pch.h

/*
 * This file is part of the coreboot project.
 *
 * Copyright (C) 2008-2009 coresystems GmbH
 * Copyright (C) 2012 The Chromium OS Authors.  All rights reserved.
 * Copyright (C) 2013-2015 Sage Electronic Engineering, LLC.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#ifndef SOUTHBRIDGE_INTEL_I89XX_PCH_H
#define SOUTHBRIDGE_INTEL_I89XX_PCH_H

#include <arch/acpi.h>

/* PCH types */
#define PCH_TYPE_CC	0x23 /* CaveCreek */

/* PCH stepping values for LPC device */
#define PCH_STEP_A0	0
#define PCH_STEP_A1	1
#define PCH_STEP_B0	2
#define PCH_STEP_B1	3
#define PCH_STEP_B2	4
#define PCH_STEP_B3	5

/*
 * It does not matter where we put the SMBus I/O base, as long as we
 * keep it consistent and don't interfere with other devices.  Stage2
 * will relocate this anyways.
 * Our solution is to have SMB initialization move the I/O to SMBUS_IO_BASE
 * again. But handling static BARs is a generic problem that should be
 * solved in the device allocator.
 */
#define SMBUS_IO_BASE		0x0500
#define SMBUS_SLAVE_ADDR	0x24
/* TODO Make sure these don't get changed by stage2 */
#define DEFAULT_GPIOBASE	0x0480
#define DEFAULT_PMBASE		0x0400

#ifndef __ACPI__
#define DEFAULT_RCBA		((u8 *)0xfed1c000)
#else
#define DEFAULT_RCBA		0xfed1c000
#endif

#ifndef __ACPI__
#define DEBUG_PERIODIC_SMIS 0

#if defined (__SMM__) && !defined(__ASSEMBLER__)
void intel_pch_finalize_smm(void);
#endif

#if !defined(__ASSEMBLER__) && !defined(__ROMCC__)
#if !defined(__PRE_RAM__) && !defined(__SMM__)
#include "chip.h"
int pch_silicon_revision(void);
int pch_silicon_type(void);
int pch_silicon_supported(int type, int rev);
void pch_enable(device_t dev);
#if IS_ENABLED(CONFIG_ELOG)
void pch_log_state(void);
#endif
#else
/* writes an address and one byte of data */
s16 smbus_write_single_byte(u8 device, u8 address, u8 data);

/* Sends an address and reads one byte of data */
int smbus_read_byte(unsigned device, unsigned address);

/* writes a single byte of data to smbus without an address byte */
s16 smbus_quick_write(u8 device, u8 data);

/* gets one byte of data from smbus without writing an address. */
s16 smbus_quick_read(u8 device);

void enable_smbus(void);
void enable_usb_bar(void);
int early_spi_read(u32 offset, u32 size, u8 *buffer);
void sandybridge_sb_early_initialization(void);
void early_pch_init(void);
#endif
#endif

#define MAINBOARD_POWER_OFF	0
#define MAINBOARD_POWER_ON	1
#define MAINBOARD_POWER_KEEP	2

#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif

#define PCH_EHCI1_DEV		PCI_DEV(0, 0x1d, 0)
#define PCH_ME_DEV		PCI_DEV(0, 0x16, 0)
#define PCH_PCIE_DEV_SLOT	28

/* PCI Configuration Space (D31:F0): LPC */
#define PCH_LPC_DEV		PCI_DEV(0, 0x1f, 0)
#define SERIRQ_CNTL		0x64

#define GEN_PMCON_1		0xa0
#define GEN_PMCON_2		0xa2
#define GEN_PMCON_3		0xa4
#define ETR3			0xac
#define  ETR3_CWORWRE		(1 << 18)
#define  ETR3_CF9GR		(1 << 20)

/* GEN_PMCON_3 bits */
#define RTC_BATTERY_DEAD	(1 << 2)
#define RTC_POWER_FAILED	(1 << 1)
#define SLEEP_AFTER_POWER_FAIL	(1 << 0)

#define PMBASE			0x40
#define ACPI_CNTL		0x44
#define BIOS_CNTL		0xDC
#define GPIO_BASE		0x48 /* LPC GPIO Base Address Register */
#define GPIO_CNTL		0x4C /* LPC GPIO Control Register */
#define GPIO_ROUT		0xb8

/* PIRQ[A-H] Routing registers */
#define PIRQA_ROUT		0x60
#define PIRQB_ROUT		0x61
#define PIRQC_ROUT		0x62
#define PIRQD_ROUT		0x63
#define PIRQE_ROUT		0x68
#define PIRQF_ROUT		0x69
#define PIRQG_ROUT		0x6A
#define PIRQH_ROUT		0x6B

#define LPC_IO_DEC		0x80 /* IO Decode Ranges Register */
#define LPC_EN			0x82 /* LPC IF Enables Register */
#define  CNF2_LPC_EN		(1 << 13) /* 0x4e/0x4f */
#define  CNF1_LPC_EN		(1 << 12) /* 0x2e/0x2f */
#define  MC_LPC_EN		(1 << 11) /* 0x62/0x66 */
#define  KBC_LPC_EN		(1 << 10) /* 0x60/0x64 */
#define  GAMEH_LPC_EN		(1 << 9)  /* 0x208/0x20f */
#define  GAMEL_LPC_EN		(1 << 8)  /* 0x200/0x207 */
#define  FDD_LPC_EN		(1 << 3)  /* LPC_IO_DEC[12] */
#define  LPT_LPC_EN		(1 << 2)  /* LPC_IO_DEC[9:8] */
#define  COMB_LPC_EN		(1 << 1)  /* LPC_IO_DEC[6:4] */
#define  COMA_LPC_EN		(1 << 0)  /* LPC_IO_DEC[3:2] */
#define LPC_GEN1_DEC		0x84 /* LPC IF Generic Decode Range 1 */
#define LPC_GEN2_DEC		0x88 /* LPC IF Generic Decode Range 2 */
#define LPC_GEN3_DEC		0x8c /* LPC IF Generic Decode Range 3 */
#define LPC_GEN4_DEC		0x90 /* LPC IF Generic Decode Range 4 */

/* PCI Configuration Space (D31:F2/5) */
#define PCH_SATA_DEV		PCI_DEV(0, 0x1f, 2)
#define PCH_SATA2_DEV		PCI_DEV(0, 0x1f, 5)
#define INTR_LN			0x3c
#define SATA_SIRI		0xa0 /* SATA Indexed Register Index */
#define SATA_SIRD		0xa4 /* SATA Indexed Register Data */
#define SATA_SP			0xd0 /* Scratchpad */

/* SATA IOBP Registers */
#define SATA_IOBP_SP0G3IR	0xea000151
#define SATA_IOBP_SP1G3IR	0xea000051

/* PCI Configuration Space (D31:F3): SMBus */
#define PCH_SMBUS_DEV		PCI_DEV(0, 0x1f, 3)
#define SMB_BASE		0x20
#define HOSTC			0x40
#define SMB_RCV_SLVA		0x09

/* HOSTC bits */
#define I2C_EN			(1 << 2)
#define SMB_SMI_EN		(1 << 1)
#define HST_EN			(1 << 0)

/* Southbridge IO BARs */

#define GPIOBASE		0x48

#define PMBASE		0x40

/* Root Complex Register Block */
#define RCBA		0xf0

#define RCBA8(x) *((volatile u8 *)(DEFAULT_RCBA + x))
#define RCBA16(x) *((volatile u16 *)(DEFAULT_RCBA + x))
#define RCBA32(x) *((volatile u32 *)(DEFAULT_RCBA + x))

#define RCBA_AND_OR(bits, x, and, or) \
        RCBA##bits(x) = ((RCBA##bits(x) & (and)) | (or))
#define RCBA8_AND_OR(x, and, or)  RCBA_AND_OR(8, x, and, or)
#define RCBA16_AND_OR(x, and, or) RCBA_AND_OR(16, x, and, or)
#define RCBA32_AND_OR(x, and, or) RCBA_AND_OR(32, x, and, or)
#define RCBA32_OR(x, or) RCBA_AND_OR(32, x, ~0UL, or)

#define V0CTL		0x0014	/* 32bit */
#define V0STS		0x001a	/* 16bit */

#define V1CAP		0x001c	/* 32bit */
#define V1CTL		0x0020	/* 32bit */
#define V1STS		0x0026	/* 16bit */

#define RPC		0x0224	/* 32bit */
#define RPFN		0x0238	/* 32bit */

/* Root Port configuratinon space hide */
#define RPFN_HIDE(port)         (1 << (((port) * 4) + 3))
/* Get the function number assigned to a Root Port */
#define RPFN_FNGET(reg,port)    (((reg) >> ((port) * 4)) & 7)
/* Set the function number for a Root Port */
#define RPFN_FNSET(port,func)   (((func) & 7) << ((port) * 4))
/* Root Port function number mask */
#define RPFN_FNMASK(port)       (7 << ((port) * 4))

#define TRSR		0x1e00	/*  8bit */
#define TRCR		0x1e10	/* 64bit */
#define TWDR		0x1e18	/* 64bit */

#define TCTL		0x3000	/*  8bit */

/* IO Buffer Programming */
#define IOBPIRI		0x2330
#define IOBPD		0x2334
#define IOBPS		0x2338
#define  IOBPS_RW_BX    ((1 << 9)|(1 << 10))
#define  IOBPS_WRITE_AX	((1 << 9)|(1 << 10))
#define  IOBPS_READ_AX	((1 << 8)|(1 << 9)|(1 << 10))

/*
 * Interrupt Pin (IP) and Interrupt Route (IR)
 * registers
 */
#define D31IP		0x3100	/* 32bit */
#define D31IP_TTIP	24	/* Thermal Throttle Pin */
#define D31IP_SIP2	20	/* SATA Pin 2 */
#define D31IP_SMIP	12	/* SMBUS Pin */
#define D31IP_SIP	8	/* SATA Pin */
#define D29IP		0x3108	/* 32bit */
#define D29IP_E1P	0	/* EHCI #1 Pin */
#define D28IP		0x310c	/* 32bit */
#define D28IP_P4IP	12	/* PCI Express Port 4 */
#define D28IP_P3IP	8	/* PCI Express Port 3 */
#define D28IP_P2IP	4	/* PCI Express Port 2 */
#define D28IP_P1IP	0	/* PCI Express Port 1 */
#define D22IP		0x3124	/* 32bit */
#define D22IP_KTIP	12	/* KT Pin */
#define D22IP_IDERIP	8	/* IDE-R Pin */
#define D22IP_MEI2IP	4	/* MEI #2 Pin */
#define D22IP_MEI1IP	0	/* MEI #1 Pin */
#define D31IR		0x3140	/* 16bit */
#define D29IR		0x3144	/* 16bit */
#define D28IR		0x3146	/* 16bit */
#define D22IR		0x315c	/* 16bit */
#define OIC		0x31fe	/* 16bit */
#define SOFT_RESET_CTRL 0x38f4
#define SOFT_RESET_DATA 0x38f8

#if !defined(__ASSEMBLER__)
#define NUM_IR_DEVS 32

/* Certain device numbers have Interrupt registers in the RCBA */
#define PCH_ALLOWED_IRQ_DEVNUM 0xB0400000	/* 31, 29, 28, 22 */

/*
 * Some devices have specific IRQ registers in
 * the LPC for interrupt control
 */
struct dev_irq_regs {
	uint32_t ip_reg;	/* Interrupt Pin register */
	uint32_t ir_reg;	/* Interrupt Route register */
};

/*
 * Certain PCH device numbers have specific IRQ registers
 * associated with them (D(x)IP / D(x)IR) for Interrupt Pin
 * and Interrupt Routing information.
 */
static const struct dev_irq_regs irq_regs[NUM_IR_DEVS] = {
		[31] = {D31IP, D31IR},
		[29] = {D29IP, D29IR},
		[28] = {D28IP, D28IR},
		[22] = {D22IP, D22IR},
};
#endif

#define RC		0x3400	/* 32bit */
#define HPTC		0x3404	/* 32bit */
#define GCS		0x3410	/* 32bit */
#define BUC		0x3414	/* 32bit */
#define PCH_DISABLE_GBE		(1 << 5)
#define FD		0x3418	/* 32bit */
#define DISPBDF		0x3424  /* 16bit */
#define FD2		0x3428	/* 32bit */
#define CG		0x341c	/* 32bit */

/* Function Disable 1 RCBA 0x3418 */
#define PCH_DISABLE_ALWAYS	0
#define PCH_DISABLE_SATA1	(1 << 2)
#define PCH_DISABLE_SMBUS	(1 << 3)
#define PCH_DISABLE_LPC		(1 << 14)
#define PCH_DISABLE_EHCI1	(1 << 15)
#define PCH_DISABLE_PCIE(x)	(1 << (16 + x))
#define PCH_DISABLE_THERMAL	(1 << 24)
#define PCH_DISABLE_SATA2	(1 << 25)

/* Function Disable 2 RCBA 0x3428 */
#define PCH_DISABLE_KT		(1 << 4)
#define PCH_DISABLE_IDER	(1 << 3)
#define PCH_DISABLE_MEI2	(1 << 2)
#define PCH_DISABLE_MEI1	(1 << 1)

/* ICH7 GPIOBASE */
#define GPIO_USE_SEL	0x00
#define GP_IO_SEL	0x04
#define GP_LVL		0x0c
#define GPO_BLINK	0x18
#define GPI_INV		0x2c
#define GPIO_USE_SEL2	0x30
#define GP_IO_SEL2	0x34
#define GP_LVL2		0x38
#define GPIO_USE_SEL3	0x40
#define GP_IO_SEL3	0x44
#define GP_LVL3		0x48
#define GP_RST_SEL1	0x60
#define GP_RST_SEL2	0x64
#define GP_RST_SEL3	0x68

/* ICH7 PMBASE */
#define PM1_STS		0x00
#define   WAK_STS	(1 << 15)
#define   PCIEXPWAK_STS	(1 << 14)
#define   PRBTNOR_STS	(1 << 11)
#define   RTC_STS	(1 << 10)
#define   PWRBTN_STS	(1 << 8)
#define   GBL_STS	(1 << 5)
#define   BM_STS	(1 << 4)
#define   TMROF_STS	(1 << 0)
#define PM1_EN		0x02
#define   PCIEXPWAK_DIS	(1 << 14)
#define   RTC_EN	(1 << 10)
#define   PWRBTN_EN	(1 << 8)
#define   GBL_EN	(1 << 5)
#define   TMROF_EN	(1 << 0)
#define PM1_CNT		0x04
#define   GBL_RLS	(1 << 2)
#define   BM_RLD	(1 << 1)
#define   SCI_EN	(1 << 0)
#define PM1_TMR		0x08
#define PROC_CNT	0x10
#define LV2		0x14
#define LV3		0x15
#define LV4		0x16
#define PM2_CNT		0x50 // mobile only
#define GPE0_STS	0x20
#define   PME_B0_STS	(1 << 13)
#define   PME_STS	(1 << 11)
#define   BATLOW_STS	(1 << 10)
#define   PCI_EXP_STS	(1 << 9)
#define   RI_STS	(1 << 8)
#define   SMB_WAK_STS	(1 << 7)
#define   TCOSCI_STS	(1 << 6)
#define   SWGPE_STS	(1 << 2)
#define   HOT_PLUG_STS	(1 << 1)
#define GPE0_EN		0x28
#define   PME_B0_EN	(1 << 13)
#define   PME_EN	(1 << 11)
#define   TCOSCI_EN	(1 << 6)
#define SMI_EN		0x30
#define   INTEL_USB2_EN	 (1 << 18) // Intel-Specific USB2 SMI logic
#define   LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic
#define   PERIODIC_EN	 (1 << 14) // SMI on PERIODIC_STS in SMI_STS
#define   TCO_EN	 (1 << 13) // Enable TCO Logic (BIOSWE et al)
#define   MCSMI_EN	 (1 << 11) // Trap microcontroller range access
#define   BIOS_RLS	 (1 <<  7) // asserts SCI on bit set
#define   SWSMI_TMR_EN	 (1 <<  6) // start software smi timer on bit set
#define   APMC_EN	 (1 <<  5) // Writes to APM_CNT cause SMI#
#define   SLP_SMI_EN	 (1 <<  4) // Write to SLP_EN in PM1_CNT asserts SMI#
#define   LEGACY_USB_EN  (1 <<  3) // Legacy USB circuit SMI logic
#define   BIOS_EN	 (1 <<  2) // Assert SMI# on setting GBL_RLS bit
#define   EOS		 (1 <<  1) // End of SMI (deassert SMI#)
#define   GBL_SMI_EN	 (1 <<  0) // SMI# generation at all?
#define SMI_STS		0x34
#define ALT_GP_SMI_EN	0x38
#define ALT_GP_SMI_STS	0x3a
#define GPE_CNTL	0x42
#define DEVACT_STS	0x44
#define SS_CNT		0x50
#define C3_RES		0x54
#define TCO1_STS	0x64
#define   DMISCI_STS	(1 << 9)
#define TCO2_STS	0x66

/*
 * SPI Opcode Menu setup for SPIBAR lockdown
 * should support most common flash chips.
 */

#define SPI_OPMENU_0 0x01 /* WRSR: Write Status Register */
#define SPI_OPTYPE_0 0x01 /* Write, no address */

#define SPI_OPMENU_1 0x02 /* BYPR: Byte Program */
#define SPI_OPTYPE_1 0x03 /* Write, address required */

#define SPI_OPMENU_2 0x03 /* READ: Read Data */
#define SPI_OPTYPE_2 0x02 /* Read, address required */

#define SPI_OPMENU_3 0x05 /* RDSR: Read Status Register */
#define SPI_OPTYPE_3 0x00 /* Read, no address */

#define SPI_OPMENU_4 0x20 /* SE20: Sector Erase 0x20 */
#define SPI_OPTYPE_4 0x03 /* Write, address required */

#define SPI_OPMENU_5 0x9f /* RDID: Read ID */
#define SPI_OPTYPE_5 0x00 /* Read, no address */

#define SPI_OPMENU_6 0xd8 /* BED8: Block Erase 0xd8 */
#define SPI_OPTYPE_6 0x03 /* Write, address required */

#define SPI_OPMENU_7 0x0b /* FAST: Fast Read */
#define SPI_OPTYPE_7 0x02 /* Read, address required */

#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \
			  (SPI_OPMENU_5 << 8) | SPI_OPMENU_4)
#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \
			  (SPI_OPMENU_1 << 8) | SPI_OPMENU_0)

#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \
		    (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) |  \
		    (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) |	  \
		    (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0))

#define SPI_OPPREFIX ((0x50 << 8) | 0x06) /* EWSR and WREN */

#define SPIBAR_HSFS                 0x3804   /* SPI hardware sequence status */
#define  SPIBAR_HSFS_SCIP           (1 << 5) /* SPI Cycle In Progress */
#define  SPIBAR_HSFS_AEL            (1 << 2) /* SPI Access Error Log */
#define  SPIBAR_HSFS_FCERR          (1 << 1) /* SPI Flash Cycle Error */
#define  SPIBAR_HSFS_FDONE          (1 << 0) /* SPI Flash Cycle Done */
#define SPIBAR_HSFC                 0x3806   /* SPI hardware sequence control */
#define  SPIBAR_HSFC_BYTE_COUNT(c)  (((c - 1) & 0x3f) << 8)
#define  SPIBAR_HSFC_CYCLE_READ     (0 << 1) /* Read cycle */
#define  SPIBAR_HSFC_CYCLE_WRITE    (2 << 1) /* Write cycle */
#define  SPIBAR_HSFC_CYCLE_ERASE    (3 << 1) /* Erase cycle */
#define  SPIBAR_HSFC_GO             (1 << 0) /* GO: start SPI transaction */
#define SPIBAR_FADDR                0x3808   /* SPI flash address */
#define SPIBAR_FDATA(n)             (0x3810 + (4 * n)) /* SPI flash data */

#endif /* __ACPI__ */
#endif				/* SOUTHBRIDGE_INTEL_I89XX_PCH_H */