1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <console/console.h>
#include <device/mmio.h>
#include <device/pci_ops.h>
#include <device/pci_def.h>
#include <southbridge/intel/common/rcba.h>
#include <southbridge/intel/common/pmbase.h>
#include "pch.h"
#include "chip.h"
void early_usb_init(void)
{
u32 reg32;
const u32 rcba_dump[8] = {
/* 3560 */ 0x024c8001, 0x000024a3, 0x00040002, 0x01000050,
/* 3570 */ 0x02000772, 0x16000f9f, 0x1800ff4f, 0x0001d630,
};
/* Care should be taken to limit this array to not more than 80 (0x50) entries.
* See below. */
const u32 currents[] = { USBIR_TXRX_GAIN_MOBILE_LOW, USBIR_TXRX_GAIN_DEFAULT,
USBIR_TXRX_GAIN_HIGH, 0x20000f51, 0x2000094a, 0x2000035f,
USBIR_TXRX_GAIN_DESKTOP6_LOW, USBIR_TXRX_GAIN_DESKTOP6_HIGH,
USBIR_TXRX_GAIN_DESKTOP7_LOW, USBIR_TXRX_GAIN_DESKTOP7_MED,
0x20000053, 0x2000055f, 0x20000f5f};
const struct device *dev = pcidev_on_root(0x1d, 0);
const struct southbridge_intel_bd82x6x_config *config = dev->chip_info;
const struct southbridge_usb_port *portmap = config->usb_port_config;
int i;
/* Unlock registers. */
write_pmbase16(UPRWC, read_pmbase16(UPRWC) | UPRWC_WR_EN);
for (i = 0; i < 14; i++) {
/*
* If the value from devicetree is beyond the highest possible current map
* index, it is meant to go directly into (bottom 12 bits of) USBIRx.
*/
if (portmap[i].current >= ARRAY_SIZE(currents)) {
RCBA32(USBIR0 + 4 * i) = 0x20000000 | (portmap[i].current & 0xfff);
continue;
}
if (portmap[i].enabled && !pch_is_mobile() &&
currents[portmap[i].current] == USBIR_TXRX_GAIN_MOBILE_LOW) {
/*
* Note for developers: You can fix this by re-running autoport on
* vendor firmware and then updating portmap currents accordingly.
* If that is not possible, another option is to choose a non-zero
* current setting. In either case, please test all the USB ports.
*/
printk(BIOS_ERR, "%s: USB%02d: USBIR_TXRX_GAIN_MOBILE_LOW is an invalid setting for desktop!\n",
__func__, i);
RCBA32(USBIR0 + 4 * i) = USBIR_TXRX_GAIN_DEFAULT;
} else {
RCBA32(USBIR0 + 4 * i) = currents[portmap[i].current];
}
}
for (i = 0; i < 10; i++)
RCBA32(0x3538 + 4 * i) = 0;
for (i = 0; i < 8; i++)
RCBA32(0x3560 + 4 * i) = rcba_dump[i];
for (i = 0; i < 8; i++)
RCBA32(0x3580 + 4 * i) = 0;
reg32 = 0;
for (i = 0; i < 14; i++)
if (!portmap[i].enabled)
reg32 |= (1 << i);
RCBA32(USBPDO) = reg32;
reg32 = 0;
for (i = 0; i < 8; i++)
if (portmap[i].enabled && portmap[i].oc_pin >= 0)
reg32 |= (1 << (i + 8 * portmap[i].oc_pin));
RCBA32(USBOCM1) = reg32;
reg32 = 0;
for (i = 8; i < 14; i++)
if (portmap[i].enabled && portmap[i].oc_pin >= 4)
reg32 |= (1 << (i - 8 + 8 * (portmap[i].oc_pin - 4)));
RCBA32(USBOCM2) = reg32;
for (i = 0; i < 22; i++)
RCBA32(0x35a8 + 4 * i) = 0;
pci_write_config32(PCH_XHCI_DEV, 0xe4, 0x00000000);
/* Relock registers. */
write_pmbase16(UPRWC, 0);
}
|
