1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2011 Advanced Micro Devices, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/io.h>
#if CONFIG_CONSOLE_POST
/* Data */
#define UART_RBR 0x00
#define UART_TBR 0x00
/* Control */
#define UART_IER 0x01
#define UART_IIR 0x02
#define UART_FCR 0x02
#define UART_LCR 0x03
#define UART_MCR 0x04
#define UART_DLL 0x00
#define UART_DLM 0x01
/* Status */
#define UART_LSR 0x05
#define UART_MSR 0x06
#define UART_SCR 0x07
#ifndef CONFIG_TTYS0_DIV
#if ((115200%CONFIG_TTYS0_BAUD) != 0)
#error Bad ttys0 baud rate
#endif
#define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD)
#endif // CONFIG_TTYS0_DIV
#define UART_LCS CONFIG_TTYS0_LCS
#endif // CONFIG_CONSOLE_POST == 1
static void sb900_enable_rom(void)
{
u32 word;
u32 dword;
device_t dev;
dev = PCI_DEV(0, 0x14, 0x03);
/* SB900 LPC Bridge 0:20:3:44h.
* BIT6: Port Enable for serial port 0x3f8-0x3ff
* BIT29: Port Enable for KBC port 0x60 and 0x64
* BIT30: Port Enable for ACPI Micro-Controller port 0x66 and 0x62
*/
dword = pci_io_read_config32(dev, 0x44);
//dword |= (1<<6) | (1<<29) | (1<<30) ;
/*Turn on all of LPC IO Port decode enable */
dword = 0xffffffff;
pci_io_write_config32(dev, 0x44, dword);
/* SB900 LPC Bridge 0:20:3:48h.
* BIT0: Port Enable for SuperIO 0x2E-0x2F
* BIT1: Port Enable for SuperIO 0x4E-0x4F
* BIT4: Port Enable for LPC ROM Address Arrage2 (0x68-0x6C)
* BIT6: Port Enable for RTC IO 0x70-0x73
* BIT21: Port Enable for Port 0x80
*/
dword = pci_io_read_config32(dev, 0x48);
dword |= (1<<0) | (1<<1) | (1<<4) | (1<<6) | (1<<21) ;
pci_io_write_config32(dev, 0x48, dword);
/* Enable 4MB rom access at 0xFFE00000 - 0xFFFFFFFF */
/* Set the 4MB enable bits */
word = pci_io_read_config16(dev, 0x6c);
word = 0xFFC0;
pci_io_write_config16(dev, 0x6c, word);
}
static void bootblock_southbridge_init(void)
{
/* Setup the rom access for 2M */
sb900_enable_rom();
}
|
