1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
|
/* SPDX-License-Identifier: GPL-2.0-only */
/* DDR3 mem setup file for SMDK5250 board based on EXYNOS5 */
#include <device/mmio.h>
#include <console/console.h>
#include <delay.h>
#include <soc/clk.h>
#include <soc/cpu.h>
#include <soc/dmc.h>
#include <soc/setup.h>
#define RDLVL_COMPLETE_TIMEOUT 10000
static void reset_phy_ctrl(void)
{
write32(&exynos_clock->lpddr3phy_ctrl,
LPDDR3PHY_CTRL_PHY_RESET_ENABLE);
write32(&exynos_clock->lpddr3phy_ctrl,
LPDDR3PHY_CTRL_PHY_RESET_DISABLE);
udelay(500);
}
int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
int mem_reset)
{
unsigned int val;
int i;
if (mem_reset)
reset_phy_ctrl();
/* Set Impedance Output Driver */
val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
(mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
(mem->impedance << CA_CS_DRVR_DS_OFFSET) |
(mem->impedance << CA_ADR_DRVR_DS_OFFSET);
write32(&exynos_phy0_control->phy_con39, val);
write32(&exynos_phy1_control->phy_con39, val);
/* Set Read Latency and Burst Length for PHY0 and PHY1 */
val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
write32(&exynos_phy0_control->phy_con42, val);
write32(&exynos_phy1_control->phy_con42, val);
/* ZQ Calibration */
if (dmc_config_zq(mem, exynos_phy0_control, exynos_phy1_control)){
printk(BIOS_EMERG, "DRAM ZQ CALIBRATION FAILURE\n");
return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
}
/* DQ Signal */
write32(&exynos_phy0_control->phy_con14, mem->phy0_pulld_dqs);
write32(&exynos_phy1_control->phy_con14, mem->phy1_pulld_dqs);
write32(&exynos_dmc->concontrol, mem->concontrol |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT) |
(mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT));
update_reset_dll(exynos_dmc, DDR_MODE_DDR3);
/* DQS Signal */
write32(&exynos_phy0_control->phy_con4, mem->phy0_dqs);
write32(&exynos_phy1_control->phy_con4, mem->phy1_dqs);
write32(&exynos_phy0_control->phy_con6, mem->phy0_dq);
write32(&exynos_phy1_control->phy_con6, mem->phy1_dq);
write32(&exynos_phy0_control->phy_con10, mem->phy0_tFS);
write32(&exynos_phy1_control->phy_con10, mem->phy1_tFS);
val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
write32(&exynos_phy0_control->phy_con12, val);
write32(&exynos_phy1_control->phy_con12, val);
/* Start DLL locking */
write32(&exynos_phy0_control->phy_con12,
val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT));
write32(&exynos_phy1_control->phy_con12,
val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT));
update_reset_dll(exynos_dmc, DDR_MODE_DDR3);
write32(&exynos_dmc->concontrol,
mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT));
/* Memory Channel Inteleaving Size */
write32(&exynos_dmc->ivcontrol, mem->iv_size);
/* Set DMC MEMCONTROL register */
val = mem->memcontrol & ~DMC_MEMCONTROL_DSREF_ENABLE;
write32(&exynos_dmc->memcontrol, val);
write32(&exynos_dmc->memconfig0, mem->memconfig);
write32(&exynos_dmc->memconfig1, mem->memconfig);
write32(&exynos_dmc->membaseconfig0, mem->membaseconfig0);
write32(&exynos_dmc->membaseconfig1, mem->membaseconfig1);
/* Precharge Configuration */
write32(&exynos_dmc->prechconfig,
mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT);
/* Power Down mode Configuration */
write32(&exynos_dmc->pwrdnconfig,
mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT);
/* TimingRow, TimingData, TimingPower and Timingaref
* values as per Memory AC parameters
*/
write32(&exynos_dmc->timingref, mem->timing_ref);
write32(&exynos_dmc->timingrow, mem->timing_row);
write32(&exynos_dmc->timingdata, mem->timing_data);
write32(&exynos_dmc->timingpower, mem->timing_power);
/* Send PALL command */
dmc_config_prech(mem, exynos_dmc);
if (mem_reset) {
/* Send NOP, MRS and ZQINIT commands.
* Sending MRS command will reset the DRAM. We should not be
* resetting the DRAM after resume, this will lead to memory
* corruption as DRAM content is lost after DRAM reset
*/
dmc_config_mrs(mem, exynos_dmc);
}
if (mem->gate_leveling_enable) {
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
write32(&exynos_phy0_control->phy_con0, val);
write32(&exynos_phy1_control->phy_con0, val);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
write32(&exynos_phy0_control->phy_con2, val);
write32(&exynos_phy1_control->phy_con2, val);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
write32(&exynos_phy0_control->phy_con0, val);
write32(&exynos_phy1_control->phy_con0, val);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
write32(&exynos_phy0_control->phy_con12, val);
write32(&exynos_phy1_control->phy_con12, val);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
val |= RDLVL_GATE_EN;
write32(&exynos_phy0_control->phy_con2, val);
write32(&exynos_phy1_control->phy_con2, val);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
val |= CTRL_SHGATE;
write32(&exynos_phy0_control->phy_con0, val);
write32(&exynos_phy1_control->phy_con0, val);
val = PHY_CON1_RESET_VAL;
val &= ~(CTRL_GATEDURADJ_MASK);
write32(&exynos_phy0_control->phy_con1, val);
write32(&exynos_phy1_control->phy_con1, val);
write32(&exynos_dmc->rdlvl_config, CTRL_RDLVL_GATE_ENABLE);
i = RDLVL_COMPLETE_TIMEOUT;
while ((read32(&exynos_dmc->phystatus) &
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
/*
* TODO(waihong): Comment on how long this take to
* timeout
*/
udelay(1);
i--;
}
if (!i){
printk(BIOS_EMERG, "Timeout on RDLVL. No DRAM.\n");
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
}
write32(&exynos_dmc->rdlvl_config, CTRL_RDLVL_GATE_DISABLE);
write32(&exynos_phy0_control->phy_con14, 0);
write32(&exynos_phy1_control->phy_con14, 0);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
write32(&exynos_phy0_control->phy_con12, val);
write32(&exynos_phy1_control->phy_con12, val);
update_reset_dll(exynos_dmc, DDR_MODE_DDR3);
}
/* Send PALL command */
dmc_config_prech(mem, exynos_dmc);
write32(&exynos_dmc->memcontrol, mem->memcontrol);
/* Set DMC Concontrol and enable auto-refresh counter */
write32(&exynos_dmc->concontrol, mem->concontrol |
(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT) |
(mem->aref_en << CONCONTROL_AREF_EN_SHIFT));
return 0;
}
|
