1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <boot_device.h>
#include <console/console.h>
#include <soc/alternate_cbfs.h>
#include <soc/power.h>
#include <soc/spi.h>
#include <symbols.h>
/* This allows USB A-A firmware upload from a compatible host in four parts:
* The first two are the bare BL1 and the coreboot boot block, which are just
* written to their respective loading addresses. These transfers are initiated
* by the IROM / BL1, so this code has nothing to do with them.
*
* The third transfer is a valid CBFS image that contains only the romstage,
* and must be small enough to fit into the PRE_RAM CBFS cache in
* IRAM. It is loaded when this function gets called in the boot block, and
* the normal CBFS code extracts the romstage from it.
*
* The fourth transfer is also a CBFS image, but can be of arbitrary size and
* should contain all available stages/payloads/etc. It is loaded when this
* function is called a second time at the end of the romstage, and copied to
* the romstage/ramstage CBFS cache in DRAM. It will reside there for the
* rest of the firmware's lifetime and all subsequent stages can just directly
* reference it there.
*/
static int usb_cbfs_open(void)
{
if (!ENV_ROMSTAGE_OR_BEFORE)
return 0;
static int first_run = 1;
int (*irom_load_usb)(void) = *irom_load_image_from_usb_ptr;
if (!first_run)
return 0;
if (!irom_load_usb()) {
printk(BIOS_EMERG, "Unable to load CBFS image via USB!\n");
return -1;
}
/*
* We need to trust the host/irom to copy the image to our
* _cbfs_cache address... there is no way to control or even
* check the transfer size or target address from our side.
*/
printk(BIOS_DEBUG, "USB A-A transfer successful, CBFS image should now"
" be at %p\n", _cbfs_cache);
first_run = 0;
return 0;
}
/*
* SDMMC works very similar to USB A-A: we copy the CBFS image into memory
* and read it from there. While SDMMC would also allow direct block by block
* on-demand reading, we might run into problems if we call back into the IROM
* in very late boot stages (e.g. after initializing/changing MMC clocks)... so
* this seems like a safer approach. It also makes it easy to pass our image
* down to payloads.
*/
static int sdmmc_cbfs_open(void)
{
if (!ENV_ROMSTAGE_OR_BEFORE)
return 0;
/*
* In the bootblock, we just copy the small part that fits in the buffer
* and hope that it's enough (since the romstage is currently always the
* first component in the image, this should work out). In the romstage,
* we copy until our cache is full (currently 12M) to avoid the pain of
* figuring out the true image size from in here. Since this is mainly a
* developer/debug boot mode, those shortcomings should be bearable.
*/
const u32 count = REGION_SIZE(cbfs_cache) / 512;
static int first_run = 1;
int (*irom_load_sdmmc)(u32 start, u32 count, void *dst) =
*irom_sdmmc_read_blocks_ptr;
if (!first_run)
return 0;
if (!irom_load_sdmmc(1, count, _cbfs_cache)) {
printk(BIOS_EMERG, "Unable to load CBFS image from SDMMC!\n");
return -1;
}
printk(BIOS_DEBUG, "SDMMC read successful, CBFS image should now be"
" at %p\n", _cbfs_cache);
first_run = 0;
return 0;
}
const static struct mem_region_device alternate_rdev =
MEM_REGION_DEV_RO_INIT(_cbfs_cache, REGION_SIZE(cbfs_cache));
const struct region_device *boot_device_ro(void)
{
if (*iram_secondary_base == SECONDARY_BASE_BOOT_USB)
return &alternate_rdev.rdev;
switch (exynos_power->om_stat & OM_STAT_MASK) {
case OM_STAT_SDMMC:
return &alternate_rdev.rdev;
case OM_STAT_SPI:
return exynos_spi_boot_device();
default:
printk(BIOS_EMERG, "Exynos OM_STAT value 0x%x not supported!\n",
exynos_power->om_stat);
return NULL;
}
}
void boot_device_init(void)
{
if (*iram_secondary_base == SECONDARY_BASE_BOOT_USB) {
printk(BIOS_DEBUG, "Using Exynos alternate boot mode USB A-A\n");
usb_cbfs_open();
return;
}
switch (exynos_power->om_stat & OM_STAT_MASK) {
case OM_STAT_SDMMC:
printk(BIOS_DEBUG, "Using Exynos alternate boot mode SDMMC\n");
sdmmc_cbfs_open();
break;
case OM_STAT_SPI:
exynos_init_spi_boot_device();
break;
default:
printk(BIOS_EMERG, "Exynos OM_STAT value 0x%x not supported!\n",
exynos_power->om_stat);
}
}
|
