1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
|
/*
* Copyright (c) 2012 - 2013 The Linux Foundation. All rights reserved.
*/
#include <common.h>
#include <asm/arch-ipq806x/clock.h>
#include <asm/arch-ipq806x/nss/clock.h>
#include <asm/arch-ipq806x/iomap.h>
#include <asm/io.h>
/**
* uart_pll_vote_clk_enable - enables PLL8
*/
void uart_pll_vote_clk_enable(unsigned int clk_dummy)
{
setbits_le32(BB_PLL_ENA_SC0_REG, BIT(8));
if (!clk_dummy)
while((readl(PLL_LOCK_DET_STATUS_REG) & BIT(8)) == 0);
}
/**
* uart_set_rate_mnd - configures divider M and D values
*
* Sets the M, D parameters of the divider to generate the GSBI UART
* apps clock.
*/
static void uart_set_rate_mnd(unsigned int gsbi_port, unsigned int m,
unsigned int n)
{
/* Assert MND reset. */
setbits_le32(GSBIn_UART_APPS_NS_REG(gsbi_port), BIT(7));
/* Program M and D values. */
writel(MD16(m, n), GSBIn_UART_APPS_MD_REG(gsbi_port));
/* Deassert MND reset. */
clrbits_le32(GSBIn_UART_APPS_NS_REG(gsbi_port), BIT(7));
}
/**
* uart_branch_clk_enable_reg - enables branch clock
*
* Enables branch clock for GSBI UART port.
*/
static void uart_branch_clk_enable_reg(unsigned int gsbi_port)
{
setbits_le32(GSBIn_UART_APPS_NS_REG(gsbi_port), BIT(9));
}
/**
* uart_local_clock_enable - configures N value and enables root clocks
*
* Sets the N parameter of the divider and enables root clock and
* branch clocks for GSBI UART port.
*/
static void uart_local_clock_enable(unsigned int gsbi_port, unsigned int n,
unsigned int m)
{
unsigned int reg_val, uart_ns_val;
void *const reg = (void *)GSBIn_UART_APPS_NS_REG(gsbi_port);
/*
* Program the NS register, if applicable. NS registers are not
* set in the set_rate path because power can be saved by deferring
* the selection of a clocked source until the clock is enabled.
*/
reg_val = readl(reg); // REG(0x29D4+(0x20*((n)-1)))
reg_val &= ~(Uart_clk_ns_mask);
uart_ns_val = NS(BIT_POS_31,BIT_POS_16,n,m, 5, 4, 3, 1, 2, 0,3);
reg_val |= (uart_ns_val & Uart_clk_ns_mask);
writel(reg_val,reg);
/* enable MNCNTR_EN */
reg_val = readl(reg);
reg_val |= BIT(8);
writel(reg_val, reg);
/* set source to PLL8 running @384MHz */
reg_val = readl(reg);
reg_val |= 0x3;
writel(reg_val, reg);
/* Enable root. */
reg_val |= Uart_en_mask;
writel(reg_val, reg);
uart_branch_clk_enable_reg(gsbi_port);
}
/**
* uart_set_gsbi_clk - enables HCLK for UART GSBI port
*/
static void uart_set_gsbi_clk(unsigned int gsbi_port)
{
setbits_le32(GSBIn_HCLK_CTL_REG(gsbi_port), BIT(4));
}
/**
* uart_clock_config - configures UART clocks
*
* Configures GSBI UART dividers, enable root and branch clocks.
*/
void uart_clock_config(unsigned int gsbi_port, unsigned int m,
unsigned int n, unsigned int d, unsigned int clk_dummy)
{
uart_set_rate_mnd(gsbi_port, m, d);
uart_pll_vote_clk_enable(clk_dummy);
uart_local_clock_enable(gsbi_port, n, m);
uart_set_gsbi_clk(gsbi_port);
}
/**
* nand_clock_config - configure NAND controller clocks
*
* Enable clocks to EBI2. Must be invoked before touching EBI2
* registers.
*/
void nand_clock_config(void)
{
writel(CLK_BRANCH_ENA(1) | ALWAYS_ON_CLK_BRANCH_ENA(1),
EBI2_CLK_CTL_REG);
/* Wait for clock to stabilize. */
udelay(10);
}
|
