1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <device/pci_def.h>
#include <reg_script.h>
#include <stdint.h>
#include <uart8250.h>
#include <soc/iobp.h>
#include <soc/serialio.h>
const struct reg_script uart_init[] = {
/* Set MMIO BAR */
REG_PCI_WRITE32(PCI_BASE_ADDRESS_0, CONFIG_TTYS0_BASE),
/* Enable Memory access and Bus Master */
REG_PCI_OR32(PCI_COMMAND, PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER),
/* Initialize LTR */
REG_MMIO_RMW32(CONFIG_TTYS0_BASE + SIO_REG_PPR_GEN,
~SIO_REG_PPR_GEN_LTR_MODE_MASK, 0),
REG_MMIO_RMW32(CONFIG_TTYS0_BASE + SIO_REG_PPR_RST,
~(SIO_REG_PPR_RST_ASSERT), 0),
/* Take UART out of reset */
REG_MMIO_OR32(CONFIG_TTYS0_BASE + SIO_REG_PPR_RST,
SIO_REG_PPR_RST_ASSERT),
/* Set M and N divisor inputs and enable clock */
REG_MMIO_WRITE32(CONFIG_TTYS0_BASE + SIO_REG_PPR_CLOCK,
SIO_REG_PPR_CLOCK_EN | SIO_REG_PPR_CLOCK_UPDATE |
(SIO_REG_PPR_CLOCK_N_DIV << 16) |
(SIO_REG_PPR_CLOCK_M_DIV << 1)),
REG_SCRIPT_END
};
void pch_uart_init(void)
{
/* Program IOBP CB000154h[12,9:8,4:0] = 1001100011111b */
u32 gpiodf = 0x131f;
#if defined(__SIMPLE_DEVICE__)
pci_devfn_t dev;
#else
struct device *dev;
#endif
/* Put UART in byte access mode for 16550 compatibility */
switch (CONFIG_INTEL_PCH_UART_CONSOLE_NUMBER) {
case 0:
dev = PCH_DEV_UART0;
gpiodf |= SIO_IOBP_GPIODF_UART0_BYTE_ACCESS;
break;
case 1:
dev = PCH_DEV_UART1;
gpiodf |= SIO_IOBP_GPIODF_UART1_BYTE_ACCESS;
break;
default:
return;
}
/* Program IOBP GPIODF */
pch_iobp_update(SIO_IOBP_GPIODF, ~gpiodf, gpiodf);
/* Program IOBP CB000180h[5:0] = 111111b (undefined register) */
pch_iobp_update(0xcb000180, ~0x0000003f, 0x0000003f);
/* Initialize chipset uart interface */
reg_script_run_on_dev(dev, uart_init);
/*
* Perform standard UART initialization
* Divisor 1 is 115200 BAUD
*/
uart8250_mem_init(CONFIG_TTYS0_BASE, 1);
}
|
