1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <inttypes.h>
#include <console/console.h>
#include <device/mmio.h>
#include <device/smbus_host.h>
#include <amdblocks/acpimmio.h>
#include <amdblocks/smbus.h>
#include <soc/southbridge.h>
/*
* Between 1-10 seconds, We should never timeout normally
* Longer than this is just painful when a timeout condition occurs.
*/
#define SMBUS_TIMEOUT (100 * 1000 * 10)
/* FIXME: Passing host base for SMBUS is not long-term solution.
It is possible to have multiple buses behind same host. */
static u8 controller_read8(const uintptr_t base, const u8 reg)
{
return read8p(base + reg);
}
static void controller_write8(const uintptr_t base, const u8 reg, const u8 val)
{
write8p(base + reg, val);
}
static int smbus_wait_until_ready(uintptr_t mmio)
{
if ((mmio != (uintptr_t)acpimmio_smbus) &&
(mmio != (uintptr_t)acpimmio_asf)) {
printk(BIOS_ERR, "Invalid SMBus or ASF base %#" PRIxPTR "\n", mmio);
return -1;
}
u32 loops;
loops = SMBUS_TIMEOUT;
do {
u8 val;
val = controller_read8(mmio, SMBHSTSTAT);
val &= SMBHST_STAT_VAL_BITS;
if (val == 0) { /* ready now */
return 0;
}
controller_write8(mmio, SMBHSTSTAT, val);
} while (--loops);
return -2; /* time out */
}
static int smbus_wait_until_done(uintptr_t mmio)
{
u32 loops;
loops = SMBUS_TIMEOUT;
do {
u8 val;
val = controller_read8(mmio, SMBHSTSTAT);
val &= SMBHST_STAT_VAL_BITS; /* mask off reserved bits */
if (val & SMBHST_STAT_ERROR_BITS)
return -5; /* error */
/* check IRQ status bit to see if the last host command is completed */
if (val == SMBHST_STAT_INTERRUPT) {
controller_write8(mmio, SMBHSTSTAT, val); /* clr sts */
return 0;
}
} while (--loops);
return -3; /* timeout */
}
int do_smbus_recv_byte(uintptr_t mmio, u8 device)
{
u8 byte;
if (smbus_wait_until_ready(mmio) < 0)
return -2; /* not ready */
/* set the device I'm talking to */
controller_write8(mmio, SMBHSTADDR, ((device & 0x7f) << 1) | 1);
byte = controller_read8(mmio, SMBHSTCTRL);
byte &= ~SMBHST_CTRL_MODE_BITS; /* Clear [4:2] */
byte |= SMBHST_CTRL_STRT | SMBHST_CTRL_BTE_RW; /* set mode, start */
controller_write8(mmio, SMBHSTCTRL, byte);
/* poll for transaction completion */
if (smbus_wait_until_done(mmio) < 0)
return -3; /* timeout or error */
/* read results of transaction */
byte = controller_read8(mmio, SMBHSTDAT0);
return byte;
}
int do_smbus_send_byte(uintptr_t mmio, u8 device, u8 val)
{
u8 byte;
if (smbus_wait_until_ready(mmio) < 0)
return -2; /* not ready */
/* set the command... */
controller_write8(mmio, SMBHSTDAT0, val);
/* set the device I'm talking to */
controller_write8(mmio, SMBHSTADDR, ((device & 0x7f) << 1) | 0);
byte = controller_read8(mmio, SMBHSTCTRL);
byte &= ~SMBHST_CTRL_MODE_BITS; /* Clear [4:2] */
byte |= SMBHST_CTRL_STRT | SMBHST_CTRL_BTE_RW; /* set mode, start */
controller_write8(mmio, SMBHSTCTRL, byte);
/* poll for transaction completion */
if (smbus_wait_until_done(mmio) < 0)
return -3; /* timeout or error */
return 0;
}
int do_smbus_read_byte(uintptr_t mmio, u8 device, u8 address)
{
u8 byte;
if (smbus_wait_until_ready(mmio) < 0)
return -2; /* not ready */
/* set the command/address... */
controller_write8(mmio, SMBHSTCMD, address & 0xff);
/* set the device I'm talking to */
controller_write8(mmio, SMBHSTADDR, ((device & 0x7f) << 1) | 1);
byte = controller_read8(mmio, SMBHSTCTRL);
byte &= ~SMBHST_CTRL_MODE_BITS; /* Clear [4:2] */
byte |= SMBHST_CTRL_STRT | SMBHST_CTRL_BDT_RW; /* set mode, start */
controller_write8(mmio, SMBHSTCTRL, byte);
/* poll for transaction completion */
if (smbus_wait_until_done(mmio) < 0)
return -3; /* timeout or error */
/* read results of transaction */
byte = controller_read8(mmio, SMBHSTDAT0);
return byte;
}
int do_smbus_write_byte(uintptr_t mmio, u8 device, u8 address, u8 val)
{
u8 byte;
if (smbus_wait_until_ready(mmio) < 0)
return -2; /* not ready */
/* set the command/address... */
controller_write8(mmio, SMBHSTCMD, address & 0xff);
/* set the device I'm talking to */
controller_write8(mmio, SMBHSTADDR, ((device & 0x7f) << 1) | 0);
/* output value */
controller_write8(mmio, SMBHSTDAT0, val);
byte = controller_read8(mmio, SMBHSTCTRL);
byte &= ~SMBHST_CTRL_MODE_BITS; /* Clear [4:2] */
byte |= SMBHST_CTRL_STRT | SMBHST_CTRL_BDT_RW; /* set mode, start */
controller_write8(mmio, SMBHSTCTRL, byte);
/* poll for transaction completion */
if (smbus_wait_until_done(mmio) < 0)
return -3; /* timeout or error */
return 0;
}
|
