1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
/*
* coreboot UEFI PEI wrapper
*
* Copyright (c) 2011, Google Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Google Inc. nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL GOOGLE INC BE LIABLE FOR ANY DIRECT,
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef PEI_DATA_H
#define PEI_DATA_H
#include <stdint.h>
typedef struct {
uint16_t mode; // 0: Disable, 1: Enable, 2: Auto, 3: Smart Auto
uint16_t hs_port_switch_mask; // 4 bit mask, 1: switchable, 0: not switchable
uint16_t preboot_support; // 0: No xHCI preOS driver, 1: xHCI preOS driver
uint16_t xhci_streams; // 0: Disable, 1: Enable
} pch_usb3_controller_settings;
typedef void (*tx_byte_func)(unsigned char byte);
#define PEI_VERSION 6
struct pei_data
{
uint32_t pei_version;
uint32_t mchbar;
uint32_t dmibar;
uint32_t epbar;
uint32_t pciexbar;
uint16_t smbusbar;
uint32_t wdbbar;
uint32_t wdbsize;
uint32_t hpet_address;
uint32_t rcba;
uint32_t pmbase;
uint32_t gpiobase;
uint32_t thermalbase;
uint32_t system_type; // 0 Mobile, 1 Desktop/Server
uint32_t tseg_size;
uint8_t spd_addresses[4];
uint8_t ts_addresses[4];
int boot_mode;
int ec_present;
int gbe_enable;
// 0 = leave channel enabled
// 1 = disable dimm 0 on channel
// 2 = disable dimm 1 on channel
// 3 = disable dimm 0+1 on channel
int dimm_channel0_disabled;
int dimm_channel1_disabled;
/* Seed values saved in CMOS */
uint32_t scrambler_seed;
uint32_t scrambler_seed_s3;
/* Data read from flash and passed into MRC */
unsigned char *mrc_input;
unsigned int mrc_input_len;
/* Data from MRC that should be saved to flash */
unsigned char *mrc_output;
unsigned int mrc_output_len;
/*
* Max frequency DDR3 could be ran at. Could be one of four values:
* 800, 1067, 1333, 1600
*/
uint32_t max_ddr3_freq;
/*
* USB Port Configuration:
* [0] = enable
* [1] = overcurrent pin
* [2] = length
*
* Ports 0-7 can be mapped to OC0-OC3
* Ports 8-13 can be mapped to OC4-OC7
*
* Port Length
* MOBILE:
* < 0x050 = Setting 1 (back panel, 1-5in, lowest tx amplitude)
* < 0x140 = Setting 2 (back panel, 5-14in, highest tx amplitude)
* DESKTOP:
* < 0x080 = Setting 1 (front/back panel, <8in, lowest tx amplitude)
* < 0x130 = Setting 2 (back panel, 8-13in, higher tx amplitude)
* < 0x150 = Setting 3 (back panel, 13-15in, highest tx amplitude)
*/
uint16_t usb_port_config[16][3];
/* See the usb3 struct above for details */
pch_usb3_controller_settings usb3;
/* SPD data array for onboard RAM. Specify address 0xf0,
* 0xf1, 0xf2, 0xf3 to index one of the 4 slots in
* spd_address for a given "DIMM".
*/
uint8_t spd_data[4][256];
tx_byte_func tx_byte;
int ddr3lv_support;
/* pcie_init needs to be set to 1 to have the system agent initialize
* PCIe. Note: This should only be required if your system has Gen3 devices
* and it will increase your boot time by at least 100ms.
*/
int pcie_init;
/* N mode functionality. Leave this setting at 0.
* 0 Auto
* 1 1N
* 2 2N
*/
int nmode;
/* DDR refresh rate config. JEDEC Standard No.21-C Annex K allows
* for DIMM SPD data to specify whether double-rate is required for
* extended operating temperature range.
* 0 Enable double rate based upon temperature thresholds
* 1 Normal rate
* 2 Always enable double rate
*/
int ddr_refresh_rate_config;
} __packed;
#endif
|
