1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
|
/* SPDX-License-Identifier: GPL-2.0-only */
#ifndef NORTHBRIDGE_INTEL_SANDYBRIDGE_CHIP_H
#define NORTHBRIDGE_INTEL_SANDYBRIDGE_CHIP_H
#include <drivers/intel/gma/i915.h>
/*
* Digital Port Hotplug Enable:
* 0x04 = Enabled, 2ms short pulse
* 0x05 = Enabled, 4.5ms short pulse
* 0x06 = Enabled, 6ms short pulse
* 0x07 = Enabled, 100ms short pulse
*/
struct northbridge_intel_sandybridge_config {
u8 gpu_dp_b_hotplug; /* Digital Port B Hotplug Config */
u8 gpu_dp_c_hotplug; /* Digital Port C Hotplug Config */
u8 gpu_dp_d_hotplug; /* Digital Port D Hotplug Config */
u8 gpu_panel_port_select; /* 0=LVDS 1=DP_B 2=DP_C 3=DP_D */
u8 gpu_panel_power_cycle_delay; /* T4 time sequence */
u16 gpu_panel_power_up_delay; /* T1+T2 time sequence */
u16 gpu_panel_power_down_delay; /* T3 time sequence */
u16 gpu_panel_power_backlight_on_delay; /* T5 time sequence */
u16 gpu_panel_power_backlight_off_delay; /* Tx time sequence */
u32 gpu_cpu_backlight; /* CPU Backlight PWM value */
u32 gpu_pch_backlight; /* PCH Backlight PWM value */
/*
* Maximum memory clock.
* For example 666 for DDR3-1333, or 800 for DDR3-1600
*/
u16 max_mem_clock_mhz;
struct i915_gpu_controller_info gfx;
/*
* Maximum PCI MMIO size in MiB.
*/
u16 pci_mmio_size;
/* Data for RAM init */
/* DIMM SPD address. Use 8bit notation where BIT0 is always zero. */
u8 spd_addresses[4];
/* PEI data for RAM init and early silicon init */
u8 ts_addresses[4];
bool ec_present;
bool ddr3lv_support;
/*
* N mode functionality. Leave this setting at 0.
* 0 Auto
* 1 1N
* 2 2N
*/
enum {
DDR_NMODE_AUTO = 0,
DDR_NMODE_1N,
DDR_NMODE_2N,
} nmode;
/*
* DDR refresh rate config. JEDEC Standard No.21-C Annex K allows for DIMM SPD data to
* specify whether double-rate is required for extended operating temperature range.
*
* 0 Enable double rate based upon temperature thresholds
* 1 Normal rate
* 2 Always enable double rate
*/
enum {
DDR_REFRESH_RATE_TEMP_THRES = 0,
DDR_REFRESH_REATE_NORMAL,
DDR_REFRESH_RATE_DOUBLE,
} ddr_refresh_rate_config;
/*
* USB Port Configuration:
* [0] = enable
* [1] = overcurrent pin
* [2] = length
*
* Ports 0-7 can be mapped to OC0-OC3
* Ports 8-13 can be mapped to OC4-OC7
*
* Port Length
* MOBILE:
* < 0x050 = Setting 1 (back panel, 1-5in, lowest tx amplitude)
* < 0x140 = Setting 2 (back panel, 5-14in, highest tx amplitude)
* DESKTOP:
* < 0x080 = Setting 1 (front/back panel, <8in, lowest tx amplitude)
* < 0x130 = Setting 2 (back panel, 8-13in, higher tx amplitude)
* < 0x150 = Setting 3 (back panel, 13-15in, highest tx amplitude)
*/
u16 usb_port_config[16][3];
struct {
/* 0: Disable, 1: Enable, 2: Auto, 3: Smart Auto */
u8 mode : 2;
/* 4 bit mask, 1: switchable, 0: not switchable */
u8 hs_port_switch_mask : 4;
/* 0: No xHCI preOS driver, 1: xHCI preOS driver */
u8 preboot_support : 1;
/* 0: Disable, 1: Enable */
u8 xhci_streams : 1;
} usb3;
};
#endif /* NORTHBRIDGE_INTEL_SANDYBRIDGE_CHIP_H */
|
