blob: da285a5f6a54ba61885340a5b3b26431d2cf7554 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
|
uses HAVE_MP_TABLE
uses HAVE_PIRQ_TABLE
uses USE_FALLBACK_IMAGE
uses HAVE_FALLBACK_BOOT
uses HAVE_HARD_RESET
uses HARD_RESET_BUS
uses HARD_RESET_DEVICE
uses HARD_RESET_FUNCTION
uses IRQ_SLOT_COUNT
uses HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
uses FALLBACK_SIZE
uses ROM_SIZE
uses ROM_SECTION_SIZE
uses ROM_IMAGE_SIZE
uses ROM_SECTION_SIZE
uses ROM_SECTION_OFFSET
uses CONFIG_ROM_STREAM
uses CONFIG_ROM_STREAM_START
uses PAYLOAD_SIZE
uses _ROMBASE
uses XIP_ROM_SIZE
uses XIP_ROM_BASE
uses STACK_SIZE
uses HEAP_SIZE
uses USE_OPTION_TABLE
uses LB_CKS_RANGE_START
uses LB_CKS_RANGE_END
uses LB_CKS_LOC
uses MAINBOARD_PART_NUMBER
uses MAINBOARD_VENDOR
uses MAINBOARD
uses LINUXBIOS_EXTRA_VERSION
uses _RAMBASE
uses CC
uses HOSTCC
uses TTYS0_BAUD
uses TTYS0_BASE
uses TTYS0_LCS
uses DEFAULT_CONSOLE_LOGLEVEL
uses MAXIMUM_CONSOLE_LOGLEVEL
uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
###
### Build options
###
##
## ROM_SIZE is the size of boot ROM that this board will use.
##
default ROM_SIZE=524288
##
## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
##
default FALLBACK_SIZE=131072
##
## Build code for the fallback boot
##
default HAVE_FALLBACK_BOOT=1
##
## Build code to reset the motherboard from linuxBIOS
##
default HAVE_HARD_RESET=1
##
## Funky hard reset implementation
##
default HARD_RESET_BUS=1
default HARD_RESET_DEVICE=4
default HARD_RESET_FUNCTION=0
##
## Build code to export a programmable irq routing table
##
default HAVE_PIRQ_TABLE=1
default IRQ_SLOT_COUNT=9
##
## Build code to export an x86 MP table
## Useful for specifying IRQ routing values
##
default HAVE_MP_TABLE=1
##
## Build code to export a CMOS option table
##
default HAVE_OPTION_TABLE=1
##
## Move the default LinuxBIOS cmos range off of AMD RTC registers
##
default LB_CKS_RANGE_START=49
default LB_CKS_RANGE_END=122
default LB_CKS_LOC=123
##
## Build code for SMP support
## Only worry about 2 micro processors
##
default CONFIG_SMP=1
default CONFIG_MAX_CPUS=4
##
## Build code to setup a generic IOAPIC
##
default CONFIG_IOAPIC=1
##
## Clean up the motherboard id strings
##
default MAINBOARD_PART_NUMBER="Tyan"
default MAINBOARD_VENDOR="s4880"
###
### LinuxBIOS layout values
###
## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
default ROM_IMAGE_SIZE = 65536
##
## Use a small 8K stack
##
default STACK_SIZE=0x2000
##
## Use a small 16K heap
##
default HEAP_SIZE=0x4000
##
## Only use the option table in a normal image
##
default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
##
## LinuxBIOS C code runs at this location in RAM
##
default _RAMBASE=0x00004000
##
## Load the payload from the ROM
##
default CONFIG_ROM_STREAM = 1
###
### Defaults of options that you may want to override in the target config file
###
##
## The default compiler
##
default CC="gcc"
default HOSTCC="gcc"
##
## The Serial Console
##
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
## Select the serial console baud rate
default TTYS0_BAUD=115200
#default TTYS0_BAUD=57600
#default TTYS0_BAUD=38400
#default TTYS0_BAUD=19200
#default TTYS0_BAUD=9600
#default TTYS0_BAUD=4800
#default TTYS0_BAUD=2400
#default TTYS0_BAUD=1200
# Select the serial console base port
default TTYS0_BASE=0x3f8
# Select the serial protocol
# This defaults to 8 data bits, 1 stop bit, and no parity
default TTYS0_LCS=0x3
##
### Select the linuxBIOS loglevel
##
## EMERG 1 system is unusable
## ALERT 2 action must be taken immediately
## CRIT 3 critical conditions
## ERR 4 error conditions
## WARNING 5 warning conditions
## NOTICE 6 normal but significant condition
## INFO 7 informational
## DEBUG 8 debug-level messages
## SPEW 9 Way too many details
## Request this level of debugging output
default DEFAULT_CONSOLE_LOGLEVEL=7
## At a maximum only compile in this level of debugging
default MAXIMUM_CONSOLE_LOGLEVEL=7
##
## Select power on after power fail setting
default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
### End Options.lb
end
|
