1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <arch/hpet.h>
#include <bootblock_common.h>
#include <stdint.h>
#include <pc80/mc146818rtc.h>
#include <console/console.h>
#include <bootmode.h>
#include <superio/ite/common/ite.h>
#include <superio/ite/it8772f/it8772f.h>
#include <northbridge/intel/sandybridge/sandybridge.h>
#include <northbridge/intel/sandybridge/raminit.h>
#include <northbridge/intel/sandybridge/raminit_native.h>
#include <southbridge/intel/bd82x6x/pch.h>
#include <southbridge/intel/common/gpio.h>
#include <superio/smsc/lpc47n207/lpc47n207.h>
/* Stumpy USB Reset Disable defined in cmos.layout */
#if CONFIG(USE_OPTION_TABLE)
#include "option_table.h"
#define CMOS_USB_RESET_DISABLE (CMOS_VSTART_stumpy_usb_reset_disable >> 3)
#else
#define CMOS_USB_RESET_DISABLE (400 >> 3)
#endif
#define USB_RESET_DISABLE_MAGIC (0xdd) /* Disable if set to this */
#define SUPERIO_DEV PNP_DEV(0x2e, 0)
#define SERIAL_DEV PNP_DEV(0x2e, IT8772F_SP1)
#define GPIO_DEV PNP_DEV(0x2e, IT8772F_GPIO)
void mainboard_late_rcba_config(void)
{
/*
* GFX INTA -> PIRQA (MSI)
* D28IP_P1IP WLAN INTA -> PIRQB
* D28IP_P4IP ETH0 INTB -> PIRQC
* D29IP_E1P EHCI1 INTA -> PIRQD
* D26IP_E2P EHCI2 INTA -> PIRQE
* D31IP_SIP SATA INTA -> PIRQF (MSI)
* D31IP_SMIP SMBUS INTB -> PIRQG
* D31IP_TTIP THRT INTC -> PIRQH
* D27IP_ZIP HDA INTA -> PIRQG (MSI)
*/
/* Device interrupt pin register (board specific) */
RCBA32(D31IP) = (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) |
(INTB << D31IP_SMIP) | (INTA << D31IP_SIP);
RCBA32(D30IP) = (NOINT << D30IP_PIP);
RCBA32(D29IP) = (INTA << D29IP_E1P);
RCBA32(D28IP) = (INTA << D28IP_P1IP) | (INTC << D28IP_P3IP) |
(INTB << D28IP_P4IP);
RCBA32(D27IP) = (INTA << D27IP_ZIP);
RCBA32(D26IP) = (INTA << D26IP_E2P);
RCBA32(D25IP) = (NOINT << D25IP_LIP);
RCBA32(D22IP) = (NOINT << D22IP_MEI1IP);
/* Device interrupt route registers */
DIR_ROUTE(D31IR, PIRQF, PIRQG, PIRQH, PIRQA);
DIR_ROUTE(D29IR, PIRQD, PIRQE, PIRQF, PIRQG);
DIR_ROUTE(D28IR, PIRQB, PIRQC, PIRQD, PIRQE);
DIR_ROUTE(D27IR, PIRQG, PIRQH, PIRQA, PIRQB);
DIR_ROUTE(D26IR, PIRQE, PIRQF, PIRQG, PIRQH);
DIR_ROUTE(D25IR, PIRQA, PIRQB, PIRQC, PIRQD);
DIR_ROUTE(D22IR, PIRQA, PIRQB, PIRQC, PIRQD);
}
static void setup_sio_gpios(void)
{
/*
* GPIO10 as USBPWRON12#
* GPIO12 as USBPWRON13#
*/
it8772f_gpio_setup(SUPERIO_DEV, 1, 0x05, 0x05, 0x00, 0x05, 0x05);
/*
* GPIO22 as wake SCI#
*/
it8772f_gpio_setup(SUPERIO_DEV, 2, 0x04, 0x04, 0x00, 0x04, 0x04);
/*
* GPIO32 as EXTSMI#
*/
it8772f_gpio_setup(SUPERIO_DEV, 3, 0x04, 0x04, 0x00, 0x04, 0x04);
/*
* GPIO45 as LED_POWER#
*/
it8772f_gpio_led(GPIO_DEV, 4 /* set */, (0x1 << 5) /* select */,
(0x1 << 5) /* polarity */, (0x1 << 5) /* 1 = pullup */,
(0x1 << 5) /* output */, (0x1 << 5) /* 1 = Simple IO function */,
SIO_GPIO_BLINK_GPIO45, IT8772F_GPIO_BLINK_FREQUENCY_1_HZ);
/*
* GPIO51 as USBPWRON8#
* GPIO52 as USBPWRON1#
*/
it8772f_gpio_setup(SUPERIO_DEV, 5, 0x06, 0x06, 0x00, 0x06, 0x06);
it8772f_gpio_setup(SUPERIO_DEV, 6, 0x00, 0x00, 0x00, 0x00, 0x00);
}
void mainboard_fill_pei_data(struct pei_data *pei_data)
{
struct pei_data pei_data_template = {
.pei_version = PEI_VERSION,
.mchbar = CONFIG_FIXED_MCHBAR_MMIO_BASE,
.dmibar = CONFIG_FIXED_DMIBAR_MMIO_BASE,
.epbar = CONFIG_FIXED_EPBAR_MMIO_BASE,
.pciexbar = CONFIG_ECAM_MMCONF_BASE_ADDRESS,
.smbusbar = CONFIG_FIXED_SMBUS_IO_BASE,
.wdbbar = 0x4000000,
.wdbsize = 0x1000,
.hpet_address = HPET_BASE_ADDRESS,
.rcba = (uintptr_t)DEFAULT_RCBA,
.pmbase = DEFAULT_PMBASE,
.gpiobase = DEFAULT_GPIOBASE,
.thermalbase = 0xfed08000,
.system_type = 0, // 0 Mobile, 1 Desktop/Server
.tseg_size = CONFIG_SMM_TSEG_SIZE,
.spd_addresses = { 0xa0, 0x00,0xa4,0x00 },
.ts_addresses = { 0x00, 0x00, 0x00, 0x00 },
.ec_present = 0,
.max_ddr3_freq = 1333,
.usb_port_config = {
{ 1, 0, 0x0080 }, /* P0: Front port (OC0) */
{ 1, 1, 0x0040 }, /* P1: Back port (OC1) */
{ 1, 0, 0x0040 }, /* P2: MINIPCIE1 (no OC) */
{ 1, 0, 0x0040 }, /* P3: MMC (no OC) */
{ 1, 2, 0x0080 }, /* P4: Front port (OC2) */
{ 0, 0, 0x0000 }, /* P5: Empty */
{ 0, 0, 0x0000 }, /* P6: Empty */
{ 0, 0, 0x0000 }, /* P7: Empty */
{ 1, 4, 0x0040 }, /* P8: Back port (OC4) */
{ 1, 4, 0x0040 }, /* P9: MINIPCIE3 (no OC) */
{ 1, 4, 0x0040 }, /* P10: BLUETOOTH (no OC) */
{ 0, 4, 0x0000 }, /* P11: Empty */
{ 1, 6, 0x0040 }, /* P12: Back port (OC6) */
{ 1, 5, 0x0040 }, /* P13: Back port (OC5) */
},
};
*pei_data = pei_data_template;
}
void mainboard_get_spd(spd_raw_data *spd, bool id_only)
{
read_spd(&spd[0], 0x50, id_only);
read_spd(&spd[2], 0x52, id_only);
}
const struct southbridge_usb_port mainboard_usb_ports[] = {
/* enabled power USB oc pin */
{ 1, 1, 0 }, /* P0: Front port (OC0) */
{ 1, 0, 1 }, /* P1: Back port (OC1) */
{ 1, 0, -1 }, /* P2: MINIPCIE1 (no OC) */
{ 1, 0, -1 }, /* P3: MMC (no OC) */
{ 1, 1, 2 }, /* P4: Front port (OC2) */
{ 0, 0, -1 }, /* P5: Empty */
{ 0, 0, -1 }, /* P6: Empty */
{ 0, 0, -1 }, /* P7: Empty */
{ 1, 0, 4 }, /* P8: Back port (OC4) */
{ 1, 0, -1 }, /* P9: MINIPCIE3 (no OC) */
{ 1, 0, -1 }, /* P10: BLUETOOTH (no OC) */
{ 0, 0, -1 }, /* P11: Empty */
{ 1, 0, 6 }, /* P12: Back port (OC6) */
{ 1, 0, 5 }, /* P13: Back port (OC5) */
};
int mainboard_should_reset_usb(int s3resume)
{
if (s3resume) {
/*
* For Stumpy the back USB ports are reset on resume
* so default to resetting the controller to make the
* kernel happy. There is a CMOS flag to disable the
* controller reset in case the kernel can tolerate
* the device power loss better in the future.
*/
u8 magic = cmos_read(CMOS_USB_RESET_DISABLE);
if (magic == USB_RESET_DISABLE_MAGIC) {
printk(BIOS_DEBUG, "USB Controller Reset Disabled\n");
return 0;
} else {
printk(BIOS_DEBUG, "USB Controller Reset Enabled\n");
return 1;
}
} else {
/* Ensure USB reset on resume is enabled at boot */
cmos_write(0, CMOS_USB_RESET_DISABLE);
return 1;
}
}
void bootblock_mainboard_early_init(void)
{
if (CONFIG(DRIVERS_UART_8250IO))
try_enabling_LPC47N207_uart();
setup_sio_gpios();
/* Early SuperIO setup */
it8772f_ac_resume_southbridge(SUPERIO_DEV);
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
}
|
