1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
## SPDX-License-Identifier: GPL-2.0-only
chip northbridge/intel/sandybridge
# IGD Displays
register "gfx.ndid" = "4"
register "gfx.did" = "{ 0x80000400, 0x80000300, 0x80000301, 0x80000100, }"
# Enable Panel as eDP and configure power delays
register "gpu_panel_port_select" = "PANEL_PORT_DP_A"
register "gpu_panel_power_cycle_delay" = "6" # 500ms
register "gpu_panel_power_up_delay" = "2000" # 200ms
register "gpu_panel_power_down_delay" = "500" # 50ms
register "gpu_panel_power_backlight_on_delay" = "1" # 100us as recommended by PRM
register "gpu_panel_power_backlight_off_delay" = "2000" # 200ms
# Set backlight PWM values for eDP
register "gpu_cpu_backlight" = "0x00000ac8"
register "gpu_pch_backlight" = "0x13120000"
device cpu_cluster 0 on
chip cpu/intel/model_206ax
# Magic APIC ID to locate this chip
device lapic 0x0 on end
device lapic 0xacac off end
register "acpi_c1" = "1" # ACPI(C1) = MWAIT(C1)
register "acpi_c2" = "4" # ACPI(C2) = MWAIT(C6)
register "acpi_c3" = "0"
end
end
device domain 0 on
device pci 00.0 on end # host bridge
device pci 02.0 on end # vga controller
chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH
# LPC i/o generic decodes
register "gen1_dec" = "0x003c0a01" # ITE environment controller
register "gen2_dec" = "0x000403e9" # additional com port
register "gen3_dec" = "0x000402e9" # additional com port
# Enable both SATA ports 0, 1
register "sata_port_map" = "0x03"
# Set max SATA speed to 6.0 Gb/s (should be the default, anyway)
register "sata_interface_speed_support" = "0x3"
# Route GPI7 (EC SCI) as SCI
register "gpi7_routing" = "2"
# Enable GPE17 (GPI7) and TCO SCI
register "gpe0_en" = "0x00800040"
# Disable root port coalescing
register "pcie_port_coalesce" = "0"
register "pcie_hotplug_map" = "{ 0, 0, 0, 0, 0, 0, 1, 1 }"
register "xhci_overcurrent_mapping" = "0x00000c03"
register "xhci_switchable_ports" = "0x0f"
register "superspeed_capable_ports" = "0x0f"
register "spi_uvscc" = "0x2005"
register "spi_lvscc" = "0x2005"
device pci 14.0 on end # USB 3.0 Controller
device pci 16.0 on end # Management Engine Interface 1
device pci 16.1 off end # Management Engine Interface 2
device pci 16.2 off end # Management Engine IDE-R
device pci 16.3 off end # Management Engine KT
device pci 19.0 on end # Intel Gigabit Ethernet
device pci 1a.0 on end # USB2 EHCI #2
device pci 1b.0 on # High Definition Audio
subsystemid 0x1a86 0x4352
end
# Disabling 1c.0 might break IRQ settings as it enables port coalescing
device pci 1c.0 on end # PCIe Port #1
device pci 1c.1 on end # PCIe Port #2
device pci 1c.2 on end # PCIe Port #3
device pci 1c.3 on end # PCIe Port #4
device pci 1c.4 on end # PCIe Port #5
device pci 1c.5 on end # PCIe Port #6
device pci 1c.6 on end # PCIe Port #7
device pci 1c.7 on end # PCIe Port #8
device pci 1d.0 on end # USB2 EHCI #1
device pci 1e.0 off end # PCI bridge
device pci 1f.0 on # LPC bridge
chip ec/roda/it8518
register "cpuhot_limit" = "100"
# 60h/64h KBC
device pnp ff.0 on # dummy address
end
end
chip superio/ite/it8783ef
register "TMPIN1.mode" = "THERMAL_RESISTOR"
register "TMPIN2.mode" = "THERMAL_RESISTOR"
register "ec.vin_mask" = "VIN_ALL"
register "FAN1.mode" = "FAN_SMART_AUTOMATIC"
register "FAN1.smart.tmpin" = " 1"
register "FAN1.smart.tmp_off" = "60"
register "FAN1.smart.tmp_start" = "64"
register "FAN1.smart.tmp_delta" = " 2"
register "FAN1.smart.pwm_start" = "30"
register "FAN1.smart.slope" = "64"
register "FAN2.mode" = "FAN_SMART_AUTOMATIC"
register "FAN2.smart.tmpin" = " 1"
register "FAN2.smart.tmp_off" = "60"
register "FAN2.smart.tmp_start" = "64"
register "FAN2.smart.tmp_delta" = " 2"
register "FAN2.smart.pwm_start" = "30"
register "FAN2.smart.slope" = "64"
register "FAN3.mode" = "FAN_MODE_OFF"
device pnp 2e.0 off end # Floppy
device pnp 2e.1 on # COM 1
io 0x60 = 0x3f8
irq 0x70 = 4
end
device pnp 2e.2 on # COM 2
io 0x60 = 0x2f8
irq 0x70 = 3
end
device pnp 2e.3 on # Printer Port
io 0x60 = 0x378
io 0x62 = 0x000
irq 0x70 = 7
drq 0x74 = 4
irq 0xf0 = 0x00
end
device pnp 2e.4 on # Environment Controller
io 0x60 = 0xa30
io 0x62 = 0xa20
irq 0x70 = 0
irq 0xf0 = 0x80
end
device pnp 2e.5 off end # Keyboard
device pnp 2e.6 off end # Mouse
device pnp 2e.7 off end # GPIO
device pnp 2e.8 on # COM 3
io 0x60 = 0x3e8
irq 0x70 = 4
end
device pnp 2e.9 on # COM 4
io 0x60 = 0x2e8
irq 0x70 = 3
end
device pnp 2e.a off end # COM 5
device pnp 2e.b off end # COM 6
device pnp 2e.c off end # CIR
end
end # LPC bridge
device pci 1f.2 on end # SATA Controller 1
device pci 1f.3 on end # SMBus
device pci 1f.5 off end # SATA Controller 2
device pci 1f.6 off end # Thermal
end
end
end
|
