1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootblock_common.h>
#include <stdint.h>
#include <arch/io.h>
#include <device/pnp_ops.h>
#include <device/pci_ops.h>
#include <device/pci_def.h>
#include <option.h>
#include <northbridge/intel/i945/i945.h>
#include <southbridge/intel/i82801gx/i82801gx.h>
#include <superio/smsc/lpc47n227/lpc47n227.h>
/* Override the default lpc decode ranges */
void mainboard_lpc_decode(void)
{
int lpt_en = 0;
if (get_uint_option("lpt", 0))
lpt_en = LPT_LPC_EN; /* enable LPT */
pci_write_config16(PCI_DEV(0, 0x1f, 0), LPC_IO_DEC, 0x0007);
pci_update_config16(PCI_DEV(0, 0x1f, 0), LPC_EN, ~LPT_LPC_EN, lpt_en);
}
/* This box has two superios, so enabling serial becomes slightly excessive.
* We disable a lot of stuff to make sure that there are no conflicts between
* the two. Also set up the GPIOs from the beginning. This is the "no schematic
* but safe anyways" method.
*/
void bootblock_mainboard_early_init(void)
{
const pnp_devfn_t dev = PNP_DEV(0x2e, 0x00);
pnp_enter_conf_state(dev);
pnp_write_config(dev, 0x01, 0x94); /* Extended Parport modes */
pnp_write_config(dev, 0x02, 0x88); /* UART power on */
pnp_write_config(dev, 0x03, 0x72); /* Floppy */
pnp_write_config(dev, 0x04, 0x01); /* EPP + SPP */
pnp_write_config(dev, 0x14, 0x03); /* Floppy */
pnp_write_config(dev, 0x20, (0x3f0 >> 2)); /* Floppy */
pnp_write_config(dev, 0x23, (0x378 >> 2)); /* PP base */
pnp_write_config(dev, 0x24, (0x3f8 >> 2)); /* UART1 base */
pnp_write_config(dev, 0x25, (0x2f8 >> 2)); /* UART2 base */
pnp_write_config(dev, 0x26, (2 << 4) | 0); /* FDC + PP DMA */
pnp_write_config(dev, 0x27, (6 << 4) | 7); /* FDC + PP DMA */
pnp_write_config(dev, 0x28, (4 << 4) | 3); /* UART1,2 IRQ */
/* These are the SMI status registers in the SIO: */
pnp_write_config(dev, 0x30, (0x600 >> 4)); /* Runtime Register Block Base */
pnp_write_config(dev, 0x31, 0x00); /* GPIO1 DIR */
pnp_write_config(dev, 0x32, 0x00); /* GPIO1 POL */
pnp_write_config(dev, 0x33, 0x40); /* GPIO2 DIR */
pnp_write_config(dev, 0x34, 0x00); /* GPIO2 POL */
pnp_write_config(dev, 0x35, 0xff); /* GPIO3 DIR */
pnp_write_config(dev, 0x36, 0x00); /* GPIO3 POL */
pnp_write_config(dev, 0x37, 0xe0); /* GPIO4 DIR */
pnp_write_config(dev, 0x38, 0x00); /* GPIO4 POL */
pnp_write_config(dev, 0x39, 0x80); /* GPIO4 POL */
pnp_exit_conf_state(dev);
}
void mainboard_late_rcba_config(void)
{
/* Device 1f interrupt pin register */
RCBA32(D31IP) = 0x00042220;
/* dev irq route register */
RCBA16(D31IR) = 0x0232;
RCBA16(D30IR) = 0x3246;
RCBA16(D29IR) = 0x0237;
RCBA16(D28IR) = 0x3201;
RCBA16(D27IR) = 0x3216;
/* Disable unused devices */
RCBA32(FD) |= FD_INTLAN;
/* This should probably go into the ACPI OS Init trap */
/* Set up I/O Trap #0 for 0xfe00 (SMIC) */
RCBA32(0x1e84) = 0x00020001;
RCBA32(0x1e80) = 0x0000fe01;
/* Set up I/O Trap #3 for 0x800-0x80c (Trap) */
RCBA32(0x1e9c) = 0x000200f0;
RCBA32(0x1e98) = 0x000c0801;
}
static void init_artec_dongle(void)
{
/* Enable 4MB decoding */
outb(0xf1, 0x88);
outb(0xf4, 0x88);
}
void mainboard_pre_raminit_config(int s3_resume)
{
init_artec_dongle();
}
|
