1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
chip soc/intel/skylake
# IGD Displays
register "gfx" = "GMA_STATIC_DISPLAYS(0)"
register "panel_cfg" = "{
.up_delay_ms = 200,
.down_delay_ms = 50,
.cycle_delay_ms = 500,
.backlight_on_delay_ms = 1,
.backlight_off_delay_ms = 200,
.backlight_pwm_hz = 200,
}"
register "deep_s3_enable_ac" = "0"
register "deep_s3_enable_dc" = "0"
register "deep_s5_enable_ac" = "0"
register "deep_s5_enable_dc" = "0"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
register "eist_enable" = "1"
# Set the Thermal Control Circuit (TCC) activaction value to 95C
# even though FSP integration guide says to set it to 100C for SKL-U
# (offset at 0), because when the TCC activates at 100C, the CPU
# will have already shut itself down from overheating protection.
register "tcc_offset" = "5" # TCC of 95C
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_C"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
# EC host command ranges are in 0x380-0x383 & 0x80-0x8f
register "gen1_dec" = "0x00000381"
# Disable DPTF
register "dptf_enable" = "0"
# FSP Configuration
register "SataSalpSupport" = "0"
register "SataPortsEnable[0]" = "1"
register "SataPortsEnable[1]" = "0"
register "SataPortsEnable[2]" = "1"
register "SataPortsDevSlp[0]" = "0"
register "SataPortsDevSlp[2]" = "0"
register "DspEnable" = "0"
register "IoBufferOwnership" = "0"
register "SsicPortEnable" = "0"
register "ScsEmmcHs400Enabled" = "0"
register "SkipExtGfxScan" = "1"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "1" # 1s
register "PmConfigSlpSusMinAssert" = "3" # 500ms
register "PmConfigSlpAMinAssert" = "3" # 2s
# EC/KBC requires continuous mode
register "serirq_mode" = "SERIRQ_CONTINUOUS"
# VR Settings Configuration for 4 Domains
#+----------------+-----------+-----------+-------------+----------+
#| Domain/Setting | SA | IA | GT Unsliced | GT |
#+----------------+-----------+-----------+-------------+----------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 4A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| IccMax | 7A | 34A | 35A | 35A |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AC LoadLine | 15 mOhm | 5.7 mOhm | 5.2 mOhm | 5.2 mOhm |
#| DC LoadLine | 14.3 mOhm | 4.83 mOhm | 4.2 mOhm | 4.2 mOhm |
#+----------------+-----------+-----------+-------------+----------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(4),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(7),
.voltage_limit = 1520,
.ac_loadline = 1500,
.dc_loadline = 1430,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(34),
.voltage_limit = 1520,
.ac_loadline = 570,
.dc_loadline = 483,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
.ac_loadline = 520,
.dc_loadline = 420,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
.ac_loadline = 520,
.dc_loadline = 420,
}"
# Enable Root Ports 5 and 9
register "PcieRpEnable[4]" = "1"
register "PcieRpEnable[8]" = "1"
# PL2 override 25W
register "power_limits_config" = "{
.tdp_pl2_override = 25,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
device cpu_cluster 0 on end
device domain 0 on
device ref igpu on end
device ref sa_thermal on end
device ref south_xhci on end
device ref south_xdci on end
device ref thermal on end
device ref sata on end
device ref pcie_rp1 on end
device ref pcie_rp9 on end
device ref lpc_espi on
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
end
device ref hda on end
device ref smbus on end
device ref fast_spi on end
end
end
|
