1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
|
chip soc/intel/skylake
# IGD Displays
register "gfx" = "GMA_STATIC_DISPLAYS(0)"
register "panel_cfg" = "{
.up_delay_ms = 200,
.down_delay_ms = 50,
.cycle_delay_ms = 500,
.backlight_on_delay_ms = 1,
.backlight_off_delay_ms = 200,
.backlight_pwm_hz = 200,
}"
register "deep_s3_enable_ac" = "0"
register "deep_s3_enable_dc" = "0"
register "deep_s5_enable_ac" = "0"
register "deep_s5_enable_dc" = "0"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
register "eist_enable" = "1"
# Set the Thermal Control Circuit (TCC) activaction value to 95C
# even though FSP integration guide says to set it to 100C for SKL-U
# (offset at 0), because when the TCC activates at 100C, the CPU
# will have already shut itself down from overheating protection.
register "tcc_offset" = "5" # TCC of 95C
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_C"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
# EC host command ranges are in 0x380-0x383 & 0x80-0x8f
register "gen1_dec" = "0x00000381"
# Disable DPTF
register "dptf_enable" = "0"
# FSP Configuration
register "SataSalpSupport" = "0"
register "SataMode" = "0"
register "SataPortsEnable[0]" = "1"
register "SataPortsEnable[1]" = "0"
register "SataPortsEnable[2]" = "1"
register "SataPortsDevSlp[0]" = "0"
register "SataPortsDevSlp[2]" = "0"
register "DspEnable" = "0"
register "IoBufferOwnership" = "0"
register "SsicPortEnable" = "0"
register "ScsEmmcHs400Enabled" = "0"
register "SkipExtGfxScan" = "1"
register "HeciEnabled" = "0"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "1" # 1s
register "PmConfigSlpSusMinAssert" = "3" # 500ms
register "PmConfigSlpAMinAssert" = "3" # 2s
# EC/KBC requires continuous mode
register "serirq_mode" = "SERIRQ_CONTINUOUS"
# VR Settings Configuration for 4 Domains
#+----------------+-----------+-----------+-------------+----------+
#| Domain/Setting | SA | IA | GT Unsliced | GT |
#+----------------+-----------+-----------+-------------+----------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 4A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| IccMax | 7A | 34A | 35A | 35A |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AC LoadLine | 15 mOhm | 5.7 mOhm | 5.2 mOhm | 5.2 mOhm |
#| DC LoadLine | 14.3 mOhm | 4.83 mOhm | 4.2 mOhm | 4.2 mOhm |
#+----------------+-----------+-----------+-------------+----------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(4),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(7),
.voltage_limit = 1520,
.ac_loadline = 1500,
.dc_loadline = 1430,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(34),
.voltage_limit = 1520,
.ac_loadline = 570,
.dc_loadline = 483,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
.ac_loadline = 520,
.dc_loadline = 420,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
.ac_loadline = 520,
.dc_loadline = 420,
}"
# Enable Root Ports 5 and 9
register "PcieRpEnable[4]" = "1"
register "PcieRpEnable[8]" = "1"
# PL2 override 25W
register "power_limits_config" = "{
.tdp_pl2_override = 25,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
device cpu_cluster 0 on
device lapic 0 on end
end
device domain 0 on
device pci 00.0 on end # Host Bridge
device pci 02.0 on end # Integrated Graphics Device
device pci 04.0 on end # SA thermal subsystem
device pci 14.0 on end # USB xHCI
device pci 14.1 on end # USB xDCI (OTG)
device pci 14.2 on end # Thermal Subsystem
device pci 14.3 off end # Camera
device pci 16.0 on end # Management Engine Interface 1
device pci 16.1 off end # Management Engine Interface 2
device pci 16.2 off end # Management Engine IDE-R
device pci 16.3 off end # Management Engine KT Redirection
device pci 16.4 off end # Management Engine Interface 3
device pci 17.0 on end # SATA
device pci 1c.0 on end # PCI Express Port 1
device pci 1c.1 off end # PCI Express Port 2
device pci 1c.2 off end # PCI Express Port 3
device pci 1c.3 off end # PCI Express Port 4
device pci 1c.4 off end # PCI Express Port 5
device pci 1c.5 off end # PCI Express Port 6
device pci 1c.6 off end # PCI Express Port 7
device pci 1c.7 off end # PCI Express Port 8
device pci 1d.0 on end # PCI Express Port 9
device pci 1d.1 off end # PCI Express Port 10
device pci 1d.2 off end # PCI Express Port 11
device pci 1d.3 off end # PCI Express Port 12
device pci 1e.6 off end # SDXC
device pci 1f.0 on
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
end # LPC Interface
device pci 1f.1 on end # P2SB
device pci 1f.2 on end # Power Management Controller
device pci 1f.3 on end # Intel HDA
device pci 1f.4 on end # SMBus
device pci 1f.5 on end # PCH SPI
device pci 1f.6 off end # GbE
end
end
|
