blob: f0fd6a85f08b7f9c6c2b526ddb4b79fd65e5304e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
|
config BOARD_PURISM_BASEBOARD_LIBREM_CNL
def_bool n
select BOARD_ROMSIZE_KB_16384
select DRIVERS_GENERIC_CBFS_SERIAL
select DRIVERS_USB_ACPI
select HAVE_ACPI_RESUME
select HAVE_ACPI_TABLES
select INTEL_GMA_HAVE_VBT
select MAINBOARD_HAS_LIBGFXINIT
select NO_UART_ON_SUPERIO
select SOC_INTEL_COMMON_BLOCK_HDA_VERB
select SPD_CACHE_IN_FMAP
select SPD_READ_BY_WORD
select USE_LEGACY_8254_TIMER
if BOARD_PURISM_BASEBOARD_LIBREM_CNL
config MAINBOARD_DIR
default "purism/librem_cnl"
config MAINBOARD_FAMILY
string
default "Librem Mini" if BOARD_PURISM_LIBREM_MINI || BOARD_PURISM_LIBREM_MINI_V2
default "Librem 14" if BOARD_PURISM_LIBREM_14
config MAINBOARD_PART_NUMBER
default "Librem Mini" if BOARD_PURISM_LIBREM_MINI
default "Librem Mini v2" if BOARD_PURISM_LIBREM_MINI_V2
default "Librem 14" if BOARD_PURISM_LIBREM_14
config VARIANT_DIR
default "librem_mini" if BOARD_PURISM_LIBREM_MINI || BOARD_PURISM_LIBREM_MINI_V2
default "librem_14" if BOARD_PURISM_LIBREM_14
config OVERRIDE_DEVICETREE
default "variants/\$(CONFIG_VARIANT_DIR)/overridetree.cb"
config CBFS_SIZE
default 0x800000 if BOARD_PURISM_LIBREM_MINI
default 0xA00000 if BOARD_PURISM_LIBREM_MINI_V2
default 0x900000 if BOARD_PURISM_LIBREM_14
config DIMM_MAX
default 2
config DIMM_SPD_SIZE
default 512
config VGA_BIOS_ID
string
default "8086,3ea0" if BOARD_PURISM_LIBREM_MINI
default "8086,9b41" if BOARD_PURISM_LIBREM_MINI_V2 || BOARD_PURISM_LIBREM_14
config PXE_ROM_ID
string
default "10ec,8168"
# This platform has limited means to display POST codes
config NO_POST
default y
endif
config ENABLE_EC_UART1
bool "Enable EC UART1"
depends on BOARD_PURISM_LIBREM_MINI || BOARD_PURISM_LIBREM_MINI_V2
default n
select DRIVERS_UART_8250IO
help
Enable UART1 on the EC.
This UART can be used for boot logging by coreboot, SeaBIOS, or
Linux. It also works as a general-purpose UART.
Soldering is required to access these signals. Locate the pads for
U81 on the bottom of the board near the front edge; the IC is not
populated. TX is pin 14, RX is pin 19. The signals are 3.3V (do NOT
connect directly to an RS-232 serial port).
|
