1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2012 Advanced Micro Devices, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <stdint.h>
#include <device/pci_def.h>
#include <arch/io.h>
#include <device/pci_ops.h>
#include <device/pnp.h>
#include <arch/cpu.h>
#include <cpu/x86/lapic.h>
#include <console/console.h>
#include <northbridge/amd/agesa/state_machine.h>
#include <southbridge/amd/pi/hudson/hudson.h>
#include <superio/nuvoton/common/nuvoton.h>
#include <superio/nuvoton/nct5104d/nct5104d.h>
#include <Fch/Fch.h>
#include "gpio_ftns.h"
#define SIO_PORT 0x2e
#define SERIAL1_DEV PNP_DEV(SIO_PORT, NCT5104D_SP1)
#define SERIAL2_DEV PNP_DEV(SIO_PORT, NCT5104D_SP2)
static void early_lpc_init(void);
void board_BeforeAgesa(struct sysinfo *cb)
{
u32 val;
pci_devfn_t dev;
u32 data;
/*
* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". This following register setting has been
* replicated in every reference design since Parmer, so it is
* believed to be required even though it is not documented in
* the SoC BKDGs. Without this setting, there is no serial
* output.
*/
outb(0xd2, 0xcd6);
outb(0x00, 0xcd7);
post_code(0x30);
early_lpc_init();
hudson_clk_output_48Mhz();
post_code(0x31);
dev = PCI_DEV(0, 0x14, 3);
data = pci_read_config32(dev, LPC_IO_OR_MEM_DECODE_ENABLE);
/* enable 0x2e/0x4e IO decoding before configuring SuperIO */
pci_write_config32(dev, LPC_IO_OR_MEM_DECODE_ENABLE, data | 3);
/* COM2 on apu5 is reserved so only COM1 should be supported */
if ((CONFIG_UART_FOR_CONSOLE == 1) &&
!CONFIG(BOARD_PCENGINES_APU5))
nuvoton_enable_serial(SERIAL2_DEV, CONFIG_TTYS0_BASE);
else if (CONFIG_UART_FOR_CONSOLE == 0)
nuvoton_enable_serial(SERIAL1_DEV, CONFIG_TTYS0_BASE);
/* Disable SVI2 controller to wait for command completion */
val = pci_read_config32(PCI_DEV(0, 0x18, 5), 0x12C);
if (!(val & (1 << 30))) {
val |= (1 << 30);
pci_write_config32(PCI_DEV(0, 0x18, 5), 0x12C, val);
}
/* Disable PCI-PCI bridge and release GPIO32/33 for other uses. */
outb(0xea, 0xcd6);
outb(0x1, 0xcd7);
}
static void early_lpc_init(void)
{
u32 setting = 0x0;
//
// Configure output disabled, value low, pull up/down disabled
//
if (CONFIG(BOARD_PCENGINES_APU5)) {
configure_gpio(IOMUX_GPIO_22, Function0, GPIO_22, setting);
}
if (CONFIG(BOARD_PCENGINES_APU2) ||
CONFIG(BOARD_PCENGINES_APU3) ||
CONFIG(BOARD_PCENGINES_APU4)) {
configure_gpio(IOMUX_GPIO_32, Function0, GPIO_32, setting);
}
configure_gpio(IOMUX_GPIO_49, Function2, GPIO_49, setting);
configure_gpio(IOMUX_GPIO_50, Function2, GPIO_50, setting);
configure_gpio(IOMUX_GPIO_71, Function0, GPIO_71, setting);
//
// Configure output enabled, value low, pull up/down disabled
//
setting = GPIO_OUTPUT_ENABLE;
if (CONFIG(BOARD_PCENGINES_APU3) ||
CONFIG(BOARD_PCENGINES_APU4)) {
configure_gpio(IOMUX_GPIO_33, Function0, GPIO_33, setting);
}
configure_gpio(IOMUX_GPIO_57, Function1, GPIO_57, setting);
configure_gpio(IOMUX_GPIO_58, Function1, GPIO_58, setting);
configure_gpio(IOMUX_GPIO_59, Function3, GPIO_59, setting);
//
// Configure output enabled, value high, pull up/down disabled
//
setting = GPIO_OUTPUT_ENABLE | GPIO_OUTPUT_VALUE;
if (CONFIG(BOARD_PCENGINES_APU5)) {
configure_gpio(IOMUX_GPIO_32, Function0, GPIO_32, setting);
configure_gpio(IOMUX_GPIO_33, Function0, GPIO_33, setting);
}
configure_gpio(IOMUX_GPIO_51, Function2, GPIO_51, setting);
configure_gpio(IOMUX_GPIO_55, Function3, GPIO_55, setting);
configure_gpio(IOMUX_GPIO_64, Function2, GPIO_64, setting);
configure_gpio(IOMUX_GPIO_68, Function0, GPIO_68, setting);
}
|